| chip soc/intel/tigerlake |
| |
| register "power_limits_config[POWER_LIMITS_U_2_CORE]" = "{ |
| .tdp_pl1_override = 15, |
| .tdp_pl2_override = 51, |
| .tdp_pl4 = 71, |
| }" |
| register "power_limits_config[POWER_LIMITS_U_4_CORE]" = "{ |
| .tdp_pl1_override = 15, |
| .tdp_pl2_override = 51, |
| .tdp_pl4 = 105, |
| }" |
| |
| register "tcc_offset" = "5" # TCC of 95 |
| register "TcssAuxOri" = "1" |
| register "DdiPort1Hpd" = "0" |
| register "DdiPort2Hpd" = "0" |
| register "IomTypeCPortPadCfg[0]" = "0x090E000A" |
| register "IomTypeCPortPadCfg[1]" = "0x090E000D" |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| chipset_lockdown | CHIPSET_LOCKDOWN_COREBOOT | |
| #| GSPI0 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| | before memory is up | |
| #| GSPI1 | Fingerprint MCU | |
| #| I2C0 | Audio | |
| #| I2C1 | Touchscreen | |
| #| I2C2 | WLAN, SAR0 | |
| #| I2C3 | Camera, SAR1 | |
| #| I2C5 | Trackpad | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT, |
| .gspi[0] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 163, |
| .scl_hcnt = 75, |
| .sda_hold = 36, |
| }, |
| }, |
| }" |
| |
| #Disable Type-A Port A1 |
| register "usb2_ports[1]" = "USB2_PORT_EMPTY" |
| |
| #Disable M.2 WWAN |
| register "usb2_ports[2]" = "USB2_PORT_EMPTY" |
| |
| #improve the USB2 Port1 eye diagram |
| register "usb2_ports[3]" = "{ |
| .enable = 1, |
| .ocpin = OC_SKIP, |
| .tx_bias = USB2_BIAS_39P35MV, |
| .tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON, |
| .pre_emp_bias = USB2_BIAS_39P35MV, |
| .pre_emp_bit = USB2_FULL_BIT_PRE_EMP, |
| .type_c = 1, |
| }" |
| |
| #lower camera driving |
| register "usb2_ports[4]" = "{ |
| .enable = 1, |
| .tx_bias = 0, |
| .tx_emp_enable = 0, |
| .pre_emp_bias = 0, |
| .pre_emp_bit = 0, |
| }" |
| |
| #Type-A / Type-C C0 |
| register "usb2_ports[8]" = "USB2_PORT_TYPE_C(OC_SKIP)" |
| |
| device domain 0 on |
| device ref dptf on |
| # DPTF Policy for Eldrid board |
| chip drivers/intel/dptf |
| |
| ## Disable Active Policy from baseboard |
| register "policies.active" = "{[0] = {.target=DPTF_NONE}}" |
| |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU,CPU,87,5000), |
| [1] = DPTF_PASSIVE(CPU,TEMP_SENSOR_2,60.8,6000)}" |
| |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU,100,SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_2,75,SHUTDOWN)}" |
| |
| ## Power Limits Control |
| # 3-15W PL1 in 200mW increments, avg over 26-34s interval |
| # PL2 is fixed at 51W, avg over 26-34s interval |
| register "controls.power_limits" = "{ |
| .pl1 = {.min_power = 3000, |
| .max_power = 15000, |
| .time_window_min = 26 * MSECS_PER_SEC, |
| .time_window_max = 34 * MSECS_PER_SEC, |
| .granularity = 250,}, |
| .pl2 = {.min_power = 51000, |
| .max_power = 51000, |
| .time_window_min = 26 * MSECS_PER_SEC, |
| .time_window_max = 34 * MSECS_PER_SEC, |
| .granularity = 250,}}" |
| |
| device generic 0 on end |
| end |
| end |
| device ref i2c0 on |
| chip drivers/i2c/generic |
| register "hid" = ""10EC5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Headset Codec"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_F8)" |
| # Set the jd_src to RT5668_JD1 for jack detection |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on end |
| end |
| end |
| device ref i2c1 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""GDIX0000"" |
| register "generic.desc" = ""Goodix Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_E7_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" |
| register "generic.reset_delay_ms" = "30" |
| register "generic.reset_off_delay_ms" = "3" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" |
| register "generic.enable_delay_ms" = "12" |
| register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E3)" |
| register "generic.stop_off_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 14 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN90FC"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_E7_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" |
| register "generic.reset_delay_ms" = "20" |
| register "generic.has_power_resource" = "1" |
| register "generic.disable_gpio_export_in_crs" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 10 on end |
| end |
| end |
| device ref i2c5 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" |
| register "wake" = "GPE0_DW2_15" |
| register "probed" = "1" |
| device i2c 15 on end |
| end |
| end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| use conn1 as mux_conn[1] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref pcie_rp9 on |
| chip soc/intel/common/block/pcie/rtd3 |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B2)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A11)" |
| register "srcclk_pin" = "0" |
| device generic 0 on end |
| end |
| end |
| device ref hda on |
| chip drivers/generic/max98357a |
| register "hid" = ""MX98357A"" |
| register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A10)" |
| register "sdmode_delay" = "5" |
| device generic 0 on end |
| end |
| end |
| device ref pmc hidden |
| # The pmc_mux chip driver is a placeholder for the |
| # PMC.MUX device in the ACPI hierarchy. |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| register "usb2_port_number" = "9" |
| register "usb3_port_number" = "1" |
| # SBU & HSL follow CC |
| device generic 0 alias conn0 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| register "usb2_port_number" = "4" |
| register "usb3_port_number" = "2" |
| # SBU is fixed, HSL follows CC |
| register "sbu_orientation" = "TYPEC_ORIENTATION_NORMAL" |
| device generic 1 alias conn1 on end |
| end |
| end |
| end |
| end # PMC |
| device ref north_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(3, 2)" |
| device ref tcss_usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(2, 2)" |
| device ref tcss_usb3_port2 on |
| probe DB_USB USB3_ACTIVE |
| end |
| end |
| end |
| end |
| end |
| device ref south_xhci on |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "group" = "ACPI_PLD_GROUP(1, 1)" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(2, 1)" |
| device ref usb2_port4 on |
| probe DB_USB USB3_ACTIVE |
| end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| # The Linux Kernel does not allow an inverted BOTH_EDGE irq |
| # So we need to use GpioIO() instead of GpioInt() |
| # https://www.kernel.org/doc/Documentation/acpi/gpio-properties.txt |
| register "privacy_gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(3, 1)" |
| device ref usb2_port9 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A13)" |
| device ref usb2_port10 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(1, 2)" |
| device ref usb3_port1 on end |
| end |
| end |
| end |
| end |
| end |
| end |
