| fw_config |
| field CAMERA_WFC 38 40 |
| option CAMERA_UNPROVISIONED 0 |
| option CAMERA_OVTI5675 1 |
| option CAMERA_OVTI8856 2 |
| end |
| field CAMERA_UFC 41 42 |
| option CAMERA_UFC_UNPROVISIONED 0 |
| end |
| field CAMERA_VCM 43 44 |
| option CAMERA_VCM_UNPROVISIONED 0 |
| option CAMERA_VCM0 1 |
| end |
| field TS_SOURCE 45 48 |
| option TS_UNPROVISIONED 0 |
| option TS_ELAN_6915 1 |
| option TS_ELAN_6918 2 |
| option TS_ELAN_0001 3 |
| option TS_RAYD_0001 4 |
| option TS_WDHT0002 5 |
| option TS_GTCH7503 6 |
| option TS_ELAN_9004 7 |
| end |
| field AUDIO_CODEC_SOURCE 49 51 |
| option AUDIO_CODEC_UNPROVISIONED 0 |
| option AUDIO_CODEC_DA7219 1 |
| option AUDIO_CODEC_RT5682 2 |
| option AUDIO_CODEC_ALC5682I_VS 3 |
| end |
| end |
| |
| chip soc/intel/jasperlake |
| |
| # USB Port Configuration |
| register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # Camera |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI0 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| | before memory is up | |
| #| I2C0 | Trackpad | |
| #| I2C1 | TBD | |
| #| I2C2 | Touchscreen | |
| #| I2C3 | Camera | |
| #| I2C4 | Audio | |
| #| I2C5 | TBD | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .gspi[0] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 190, |
| .scl_hcnt = 100, |
| .sda_hold = 40, |
| } |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 190, |
| .scl_hcnt = 100, |
| .sda_hold = 40, |
| } |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 190, |
| .scl_hcnt = 100, |
| .sda_hold = 40, |
| } |
| }, |
| .i2c[4] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 190, |
| .scl_hcnt = 100, |
| .sda_hold = 40, |
| } |
| }, |
| }" |
| |
| register "power_limits_config" = "{ |
| .tdp_pl1_override = 7, |
| .tdp_pl2_override = 12, |
| }" |
| |
| register "tcc_offset" = "15" # TCC of 90C |
| |
| # Enable Acoustic noise mitigation and set slew rate to 1/8 |
| # Rest of the parameters are 0 by default. |
| register "AcousticNoiseMitigation" = "1" |
| register "SlowSlewRate" = "SlewRateFastBy8" |
| register "FastPkgCRampDisable" = "1" |
| |
| device domain 0 on |
| device pci 04.0 on |
| chip drivers/intel/dptf |
| register "options.tsr[0].desc" = ""Memory"" |
| register "options.tsr[1].desc" = ""Ambient"" |
| |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 90, 5000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 70, 6000), |
| [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 60, 5000)}" |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 80, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 80, SHUTDOWN)}" |
| register "controls.power_limits.pl1" = "{ |
| .min_power = 3000, |
| .max_power = 7000, |
| .time_window_min = 1 * MSECS_PER_SEC, |
| .time_window_max = 1 * MSECS_PER_SEC, |
| .granularity = 200,}" |
| register "controls.power_limits.pl2" = "{ |
| .min_power = 12000, |
| .max_power = 12000, |
| .time_window_min = 1 * MSECS_PER_SEC, |
| .time_window_max = 1 * MSECS_PER_SEC, |
| .granularity = 1000,}" |
| |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf[0]" = "{ 255, 3000 }" |
| register "controls.charger_perf[1]" = "{ 24, 1500 }" |
| register "controls.charger_perf[2]" = "{ 16, 1000 }" |
| register "controls.charger_perf[3]" = "{ 8, 500 }" |
| |
| device generic 0 on end |
| end |
| end # SA Thermal device |
| device pci 05.0 on # IPU - MIPI Camera |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "0x50000" |
| register "acpi_name" = ""IPU0"" |
| register "device_type" = "INTEL_ACPI_CAMERA_CIO2" |
| |
| register "cio2_num_ports" = "1" |
| register "cio2_lanes_used" = "{2}" |
| register "cio2_lane_endpoint[0]" = ""^I2C3.CAM0"" |
| register "cio2_prt[0]" = "2" |
| device generic 0 on end |
| end |
| end |
| device pci 14.0 on |
| chip drivers/usb/acpi |
| device usb 0.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 2.5 on end |
| end |
| end |
| end |
| end # USB xHCI |
| device pci 15.0 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""PNP0C50"" |
| register "generic.desc" = ""Synaptics Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_B3_IRQ)" |
| register "generic.wake" = "GPE0_DW0_03" |
| register "generic.probed" = "1" |
| register "hid_desc_reg_offset" = "0x20" |
| device i2c 0x2c on end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPP_B3_IRQ)" |
| register "wake" = "GPE0_DW0_03" |
| register "probed" = "1" |
| device i2c 15 on end |
| end |
| end # I2C 0 |
| device pci 15.2 on |
| chip drivers/generic/gpio_keys |
| register "name" = ""PENH"" |
| register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_C12)" |
| register "key.wakeup_route" = "WAKEUP_ROUTE_GPIO_IRQ" |
| register "key.wakeup_event_action" = "EV_ACT_DEASSERTED" |
| register "key.dev_name" = ""EJCT"" |
| register "key.linux_code" = "SW_PEN_INSERTED" |
| register "key.linux_input_type" = "EV_SW" |
| register "key.label" = ""pen_eject"" |
| device generic 0 on |
| probe STYLUS STYLUS_PRESENT |
| end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN6915"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D4_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D5)" |
| register "generic.reset_delay_ms" = "20" |
| register "generic.reset_off_delay_ms" = "2" |
| register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A11)" |
| register "generic.stop_delay_ms" = "280" |
| register "generic.stop_off_delay_ms" = "2" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "generic.enable_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "generic.disable_gpio_export_in_crs" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 15 on |
| probe TS_SOURCE TS_UNPROVISIONED |
| probe TS_SOURCE TS_ELAN_6915 |
| end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN6918"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D4_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D5)" |
| register "generic.reset_delay_ms" = "20" |
| register "generic.reset_off_delay_ms" = "2" |
| register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A11)" |
| register "generic.stop_delay_ms" = "280" |
| register "generic.stop_off_delay_ms" = "2" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "generic.enable_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "generic.disable_gpio_export_in_crs" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 10 on |
| probe TS_SOURCE TS_ELAN_6918 |
| end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN9004"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D4_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D5)" |
| register "generic.reset_delay_ms" = "20" |
| register "generic.reset_off_delay_ms" = "2" |
| register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A11)" |
| register "generic.stop_delay_ms" = "280" |
| register "generic.stop_off_delay_ms" = "2" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "generic.enable_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "generic.disable_gpio_export_in_crs" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 10 on |
| probe TS_SOURCE TS_ELAN_9004 |
| end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""WDHT0002"" |
| register "generic.desc" = ""WDT Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D4_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D5)" |
| register "generic.reset_delay_ms" = "20" |
| register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A11)" |
| register "generic.stop_delay_ms" = "130" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "generic.enable_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "generic.disable_gpio_export_in_crs" = "1" |
| register "hid_desc_reg_offset" = "0x20" |
| device i2c 2c on |
| probe TS_SOURCE TS_UNPROVISIONED |
| probe TS_SOURCE TS_WDHT0002 |
| end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""GTCH7503"" |
| register "generic.desc" = ""G2 Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D4_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D5)" |
| register "generic.reset_delay_ms" = "120" |
| register "generic.reset_off_delay_ms" = "3" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "generic.enable_delay_ms" = "12" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 0x40 on |
| probe TS_SOURCE TS_UNPROVISIONED |
| probe TS_SOURCE TS_GTCH7503 |
| end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0001"" |
| register "desc" = ""ELAN Touchscreen"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_D4_IRQ)" |
| register "probed" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D5)" |
| register "reset_delay_ms" = "20" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "enable_delay_ms" = "1" |
| register "has_power_resource" = "1" |
| device i2c 10 on |
| probe TS_SOURCE TS_UNPROVISIONED |
| probe TS_SOURCE TS_ELAN_0001 |
| end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""RAYD0001"" |
| register "desc" = ""Raydium Touchscreen"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_D4_IRQ)" |
| register "probed" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D5)" |
| register "reset_delay_ms" = "100" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "enable_delay_ms" = "50" |
| register "has_power_resource" = "1" |
| register "disable_gpio_export_in_crs" = "1" |
| device i2c 39 on |
| probe TS_SOURCE TS_UNPROVISIONED |
| probe TS_SOURCE TS_RAYD_0001 |
| end |
| end |
| end # I2C 2 |
| device pci 15.3 on # I2C 3 |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = ""OVTI5675"" |
| register "acpi_uid" = "0" |
| register "acpi_name" = ""CAM0"" |
| register "chip_name" = ""Ov 5675 Camera"" |
| register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" |
| |
| register "ssdb.lanes_used" = "2" |
| register "ssdb.link_used" = "1" |
| register "ssdb.vcm_type" = "0x0C" |
| register "vcm_name" = ""VCM0"" |
| register "num_freq_entries" = "1" |
| register "link_freq[0]" = "DEFAULT_LINK_FREQ" |
| register "remote_name" = ""IPU0"" |
| |
| register "has_power_resource" = "1" |
| #Controls |
| register "clk_panel.clks[0].clknum" = "1" #IMGCLKOUT_1 |
| register "clk_panel.clks[0].freq" = "1" #19.2 Mhz |
| |
| register "gpio_panel.gpio[0].gpio_num" = "GPP_D13" #power_enable_2p8 |
| register "gpio_panel.gpio[1].gpio_num" = "GPP_D14" #power_enable_1p2 |
| register "gpio_panel.gpio[2].gpio_num" = "GPP_D12" #reset |
| |
| #_ON |
| register "on_seq.ops_cnt" = "5" |
| register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" |
| register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" |
| register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" |
| register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" |
| register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" |
| |
| #_OFF |
| register "off_seq.ops_cnt" = "4" |
| register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" |
| register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" |
| register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" |
| register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" |
| |
| device i2c 36 on |
| probe CAMERA_WFC CAMERA_UNPROVISIONED |
| probe CAMERA_WFC CAMERA_OVTI5675 |
| end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = ""OVTI8856"" |
| register "acpi_uid" = "0" |
| register "acpi_name" = ""CAM0"" |
| register "chip_name" = ""Ov 8856 Camera"" |
| register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" |
| |
| register "ssdb.lanes_used" = "2" |
| register "ssdb.link_used" = "1" |
| register "ssdb.vcm_type" = "0x0C" |
| register "vcm_name" = ""VCM0"" |
| register "num_freq_entries" = "2" |
| register "link_freq[0]" = "720000000" |
| register "link_freq[1]" = "360000000" |
| register "remote_name" = ""IPU0"" |
| |
| register "has_power_resource" = "1" |
| #Controls |
| register "clk_panel.clks[0].clknum" = "1" #IMGCLKOUT_1 |
| register "clk_panel.clks[0].freq" = "1" #19.2 Mhz |
| |
| register "gpio_panel.gpio[0].gpio_num" = "GPP_D13" #power_enable_2p8 |
| register "gpio_panel.gpio[1].gpio_num" = "GPP_D14" #power_enable_1p2 |
| register "gpio_panel.gpio[2].gpio_num" = "GPP_D12" #reset |
| |
| #_ON |
| register "on_seq.ops_cnt" = "5" |
| register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" |
| register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" |
| register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" |
| register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" |
| register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" |
| |
| #_OFF |
| register "off_seq.ops_cnt" = "4" |
| register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" |
| register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" |
| register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" |
| register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" |
| |
| device i2c 10 on |
| probe CAMERA_WFC CAMERA_OVTI8856 |
| end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "3" |
| register "acpi_name" = ""VCM0"" |
| register "chip_name" = ""DW AF DAC"" |
| register "device_type" = "INTEL_ACPI_CAMERA_VCM" |
| |
| register "pr0" = ""\\_SB.PCI0.I2C3.CAM0.PRIC"" |
| register "vcm_compat" = ""dongwoon,dw9714"" |
| |
| device i2c 0C on |
| probe CAMERA_VCM CAMERA_VCM_UNPROVISIONED |
| probe CAMERA_VCM CAMERA_VCM0 |
| end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = "ACPI_DT_NAMESPACE_HID" |
| register "acpi_uid" = "1" |
| register "acpi_name" = ""NVM0"" |
| register "chip_name" = ""GT24C08"" |
| register "device_type" = "INTEL_ACPI_CAMERA_NVM" |
| |
| register "pr0" = ""\\_SB.PCI0.I2C3.CAM0.PRIC"" |
| |
| register "nvm_size" = "0x2000" |
| register "nvm_pagesize" = "1" |
| register "nvm_readonly" = "1" |
| register "nvm_width" = "0x10" |
| register "nvm_compat" = ""atmel,24c08"" |
| |
| device i2c 50 on end |
| end |
| end |
| device pci 19.0 on |
| chip drivers/i2c/generic |
| register "hid" = ""10EC5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5682"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on |
| probe AUDIO_CODEC_SOURCE AUDIO_CODEC_UNPROVISIONED |
| probe AUDIO_CODEC_SOURCE AUDIO_CODEC_RT5682 |
| end |
| end |
| chip drivers/i2c/da7219 |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)" |
| register "btn_cfg" = "50" |
| register "mic_det_thr" = "500" |
| register "jack_ins_deb" = "20" |
| register "jack_det_rate" = ""32ms_64ms"" |
| register "jack_rem_deb" = "1" |
| register "a_d_btn_thr" = "0xa" |
| register "d_b_btn_thr" = "0x16" |
| register "b_c_btn_thr" = "0x21" |
| register "c_mic_btn_thr" = "0x3e" |
| register "btn_avg" = "4" |
| register "adc_1bit_rpt" = "1" |
| register "micbias_lvl" = "2600" |
| register "mic_amp_in_sel" = ""diff"" |
| device i2c 1a on |
| probe AUDIO_CODEC_SOURCE AUDIO_CODEC_DA7219 |
| end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""RTL5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5682"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on |
| probe AUDIO_CODEC_SOURCE AUDIO_CODEC_ALC5682I_VS |
| end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""10EC1015"" |
| register "desc" = ""Realtek SPK AMP L"" |
| register "uid" = "0" |
| device i2c 28 on |
| probe AUDIO_AMP UNPROVISIONED |
| probe AUDIO_AMP RT1015_I2C |
| end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""10EC1015"" |
| register "desc" = ""Realtek SPK AMP R"" |
| register "uid" = "1" |
| device i2c 29 on |
| probe AUDIO_AMP UNPROVISIONED |
| probe AUDIO_AMP RT1015_I2C |
| end |
| end |
| end |
| device pci 1f.3 on |
| chip drivers/generic/alc1015 |
| register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D17)" |
| device generic 0 on |
| probe AUDIO_AMP RT1015P_AUTO |
| end |
| end |
| end # Intel HDA |
| device pci 1c.7 on |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_DW2_03" |
| device pci 00.0 on end |
| end |
| end # PCI Express Root Port 8 - WLAN |
| end |
| end |
