| fw_config |
| field TOUCHSCREEN_SOURCE 39 40 |
| option TOUCHSCREEN_UNPROVISIONED 0 |
| option TOUCHSCREEN_ELAN1001 1 |
| option TOUCHSCREEN_ELAN9008 2 |
| end |
| end |
| |
| fw_config |
| field AUDIO_CODEC_SOURCE 41 43 |
| option AUDIO_CODEC_UNPROVISIONED 0 |
| option AUDIO_CODEC_ALC5682 1 |
| option AUDIO_CODEC_ALC5682I_VS 2 |
| end |
| end |
| |
| chip soc/intel/jasperlake |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI0 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| | before memory is up | |
| #| I2C0 | Trackpad | |
| #| I2C2 | Touchscreen | |
| #| I2C4 | Audio | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .gspi[0] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 190, |
| .scl_hcnt = 100, |
| .sda_hold = 40, |
| } |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 190, |
| .scl_hcnt = 100, |
| .sda_hold = 40, |
| } |
| }, |
| .i2c[4] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 190, |
| .scl_hcnt = 100, |
| .sda_hold = 40, |
| } |
| }, |
| }" |
| |
| register "SerialIoI2cMode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C2] = PchSerialIoPci, |
| [PchSerialIoIndexI2C3] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C4] = PchSerialIoPci, |
| }" |
| |
| # USB Port Configuration |
| register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # Camera |
| |
| register "tcc_offset" = "8" # TCC of 97C |
| |
| device domain 0 on |
| device pci 04.0 on |
| # Default DPTF Policy for all Dedede boards if not overridden |
| chip drivers/intel/dptf |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 67, 1000), |
| [1] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_0, 62, 1000), |
| [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 58, 1000), |
| [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 40, 1000) |
| }" |
| |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 98, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 80, SHUTDOWN), |
| [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 80, SHUTDOWN) |
| }" |
| |
| ## Power Limits Control |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 6000, |
| .max_power = 6000, |
| .time_window_min = 1 * MSECS_PER_SEC, |
| .time_window_max = 1 * MSECS_PER_SEC, |
| .granularity = 200, |
| }, |
| .pl2 = { |
| .min_power = 20000, |
| .max_power = 20000, |
| .time_window_min = 1 * MSECS_PER_SEC, |
| .time_window_max = 1 * MSECS_PER_SEC, |
| .granularity = 1000, |
| } |
| }" |
| |
| register "options.tsr[0].desc" = ""Charger"" |
| register "options.tsr[1].desc" = ""Vcore"" |
| register "options.tsr[2].desc" = ""Ambient"" |
| |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 32, 2048 }, |
| [1] = { 28, 1792 }, |
| [2] = { 24, 1536 }, |
| [3] = { 20, 1280 } |
| }" |
| |
| device generic 0 on end |
| end |
| end # SA Thermal device |
| device pci 14.0 on |
| chip drivers/usb/acpi |
| device usb 0.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 2.5 on end |
| end |
| end |
| end |
| end # USB xHCI |
| |
| device pci 15.0 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPP_B3_IRQ)" |
| register "wake" = "GPE0_DW0_03" |
| register "probed" = "1" |
| device i2c 15 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN2702"" |
| register "generic.desc" = ""ELAN Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_B3_IRQ)" |
| register "generic.wake" = "GPE0_DW0_03" |
| register "generic.probed" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 15 on end |
| end |
| end |
| device pci 15.2 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0001"" |
| register "desc" = ""ELAN Touchscreen"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_D4_IRQ)" |
| register "probed" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D5)" |
| register "reset_delay_ms" = "20" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "enable_delay_ms" = "1" |
| register "has_power_resource" = "1" |
| device i2c 10 on |
| probe TOUCHSCREEN_SOURCE TOUCHSCREEN_ELAN1001 |
| probe TOUCHSCREEN_SOURCE TOUCHSCREEN_UNPROVISIONED |
| end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN9008"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D4_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D5)" |
| register "generic.enable_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "generic.enable_delay_ms" = "7" |
| register "generic.reset_delay_ms" = "70" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 10 on |
| probe TOUCHSCREEN_SOURCE TOUCHSCREEN_ELAN9008 |
| end |
| end |
| end # I2C 2 |
| device pci 19.0 on |
| chip drivers/i2c/generic |
| register "hid" = ""10EC5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5682"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on |
| probe AUDIO_CODEC_SOURCE AUDIO_CODEC_ALC5682 |
| probe AUDIO_CODEC_SOURCE AUDIO_CODEC_UNPROVISIONED |
| end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""RTL5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5682"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on |
| probe AUDIO_CODEC_SOURCE AUDIO_CODEC_ALC5682I_VS |
| end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""10EC1015"" |
| register "desc" = ""Realtek SPK AMP L"" |
| register "uid" = "0" |
| device i2c 28 on |
| probe AUDIO_AMP RT1015_I2C |
| probe AUDIO_AMP UNPROVISIONED |
| end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""10EC1015"" |
| register "desc" = ""Realtek SPK AMP R"" |
| register "uid" = "1" |
| device i2c 29 on |
| probe AUDIO_AMP RT1015_I2C |
| probe AUDIO_AMP UNPROVISIONED |
| end |
| end |
| end |
| device pci 1f.3 on |
| chip drivers/generic/alc1015 |
| register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D17)" |
| device generic 0 on |
| probe AUDIO_AMP RT1015P_AUTO |
| end |
| end |
| end # Intel HDA |
| end |
| end |
