Google Git
Sign in
cos / mirrors / cros / chromiumos / third_party / coreboot / refs/heads/factory-brya-14517.B / . / src / vendorcode / intel / fsp / fsp2_0 / raptorlake / FspsUpd.h
blob: ceac191faef4ea8f77fd2bd2e99a4dae44d9135e [file] [log] [blame]
/** @file
Copyright (c) 2022, Intel Corporation. All rights reserved.<BR>
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
* Redistributions of source code must retain the above copyright notice, this
list of conditions and the following disclaimer.
* Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
* Neither the name of Intel Corporation nor the names of its contributors may
be used to endorse or promote products derived from this software without
specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
This file is automatically generated. Please do NOT modify !!!
**/
#ifndef __FSPSUPD_H__
#define __FSPSUPD_H__
#include <FspUpd.h>
#pragma pack(1)
///
/// Azalia Header structure
///
typedef struct {
UINT16 VendorId; ///< Codec Vendor ID
UINT16 DeviceId; ///< Codec Device ID
UINT8 RevisionId; ///< Revision ID of the codec. 0xFF matches any revision.
UINT8 SdiNum; ///< SDI number, 0xFF matches any SDI.
UINT16 DataDwords; ///< Number of data DWORDs pointed by the codec data buffer.
UINT32 Reserved; ///< Reserved for future use. Must be set to 0.
} AZALIA_HEADER;
///
/// Audio Azalia Verb Table structure
///
typedef struct {
AZALIA_HEADER Header; ///< AZALIA PCH header
UINT32 *Data; ///< Pointer to the data buffer. Its length is specified in the header
} AUDIO_AZALIA_VERB_TABLE;
///
/// Refer to the definition of PCH_INT_PIN
///
typedef enum {
SiPchNoInt, ///< No Interrupt Pin
SiPchIntA,
SiPchIntB,
SiPchIntC,
SiPchIntD
} SI_PCH_INT_PIN;
///
/// The PCH_DEVICE_INTERRUPT_CONFIG block describes interrupt pin, IRQ and interrupt mode for PCH device.
///
typedef struct {
UINT8 Device; ///< Device number
UINT8 Function; ///< Device function
UINT8 IntX; ///< Interrupt pin: INTA-INTD (see SI_PCH_INT_PIN)
UINT8 Irq; ///< IRQ to be set for device.
} SI_PCH_DEVICE_INTERRUPT_CONFIG;
#define SI_PCH_MAX_DEVICE_INTERRUPT_CONFIG 64 ///< Number of all PCH devices
/** Fsp S Configuration
**/
typedef struct {
/** Offset 0x0040 - Logo Pointer
Points to PEI Display Logo Image
**/
UINT32 LogoPtr;
/** Offset 0x0044 - Logo Size
Size of PEI Display Logo Image
**/
UINT32 LogoSize;
/** Offset 0x0048 - Blt Buffer Address
Address of Blt buffer
**/
UINT32 BltBufferAddress;
/** Offset 0x004C - Blt Buffer Size
Size of Blt Buffer, is equal to PixelWidth * PixelHeight * 4 bytes (the size of
EFI_GRAPHICS_OUTPUT_BLT_PIXEL)
**/
UINT32 BltBufferSize;
/** Offset 0x0050 - Graphics Configuration Ptr
Points to VBT
**/
UINT32 GraphicsConfigPtr;
/** Offset 0x0054 - Enable Device 4
Enable/disable Device 4
$EN_DIS
**/
UINT8 Device4Enable;
/** Offset 0x0055 - Show SPI controller
Enable/disable to show SPI controller.
$EN_DIS
**/
UINT8 ShowSpiController;
/** Offset 0x0056 - Reserved
**/
UINT8 Reserved0[2];
/** Offset 0x0058 - MicrocodeRegionBase
Memory Base of Microcode Updates
**/
UINT32 MicrocodeRegionBase;
/** Offset 0x005C - MicrocodeRegionSize
Size of Microcode Updates
**/
UINT32 MicrocodeRegionSize;
/** Offset 0x0060 - Turbo Mode
Enable/Disable Turbo mode. 0: disable, 1: enable
$EN_DIS
**/
UINT8 TurboMode;
/** Offset 0x0061 - Enable SATA SALP Support
Enable/disable SATA Aggressive Link Power Management.
$EN_DIS
**/
UINT8 SataSalpSupport;
/** Offset 0x0062 - Enable SATA ports
Enable/disable SATA ports. One byte for each port, byte0 for port0, byte1 for port1,
and so on.
**/
UINT8 SataPortsEnable[8];
/** Offset 0x006A - Enable SATA DEVSLP Feature
Enable/disable SATA DEVSLP per port. 0 is disable, 1 is enable. One byte for each
port, byte0 for port0, byte1 for port1, and so on.
**/
UINT8 SataPortsDevSlp[8];
/** Offset 0x0072 - Reserved
**/
UINT8 Reserved1[2];
/** Offset 0x0074 - Reserved
**/
UINT32 Reserved2[8];
/** Offset 0x0094 - Enable USB2 ports
Enable/disable per USB2 ports. One byte for each port, byte0 for port0, byte1 for
port1, and so on.
**/
UINT8 PortUsb20Enable[16];
/** Offset 0x00A4 - Enable USB3 ports
Enable/disable per USB3 ports. One byte for each port, byte0 for port0, byte1 for
port1, and so on.
**/
UINT8 PortUsb30Enable[10];
/** Offset 0x00AE - Enable xDCI controller
Enable/disable to xDCI controller.
$EN_DIS
**/
UINT8 XdciEnable;
/** Offset 0x00AF - Reserved
**/
UINT8 Reserved3;
/** Offset 0x00B0 - Address of PCH_DEVICE_INTERRUPT_CONFIG table.
The address of the table of PCH_DEVICE_INTERRUPT_CONFIG.
**/
UINT32 DevIntConfigPtr;
/** Offset 0x00B4 - Number of DevIntConfig Entry
Number of Device Interrupt Configuration Entry. If this is not zero, the DevIntConfigPtr
must not be NULL.
**/
UINT8 NumOfDevIntConfig;
/** Offset 0x00B5 - PIRQx to IRQx Map Config
PIRQx to IRQx mapping. The valid value is 0x00 to 0x0F for each. First byte is for
PIRQA, second byte is for PIRQB, and so on. The setting is only available in Legacy
8259 PCI mode.
**/
UINT8 PxRcConfig[8];
/** Offset 0x00BD - Select GPIO IRQ Route
GPIO IRQ Select. The valid value is 14 or 15.
**/
UINT8 GpioIrqRoute;
/** Offset 0x00BE - Select SciIrqSelect
SCI IRQ Select. The valid value is 9, 10, 11, and 20, 21, 22, 23 for APIC only.
**/
UINT8 SciIrqSelect;
/** Offset 0x00BF - Select TcoIrqSelect
TCO IRQ Select. The valid value is 9, 10, 11, 20, 21, 22, 23.
**/
UINT8 TcoIrqSelect;
/** Offset 0x00C0 - Enable/Disable Tco IRQ
Enable/disable TCO IRQ
$EN_DIS
**/
UINT8 TcoIrqEnable;
/** Offset 0x00C1 - PCH HDA Verb Table Entry Number
Number of Entries in Verb Table.
**/
UINT8 PchHdaVerbTableEntryNum;
/** Offset 0x00C2 - Reserved
**/
UINT8 Reserved4[2];
/** Offset 0x00C4 - PCH HDA Verb Table Pointer
Pointer to Array of pointers to Verb Table.
**/
UINT32 PchHdaVerbTablePtr;
/** Offset 0x00C8 - PCH HDA Codec Sx Wake Capability
Capability to detect wake initiated by a codec in Sx
**/
UINT8 PchHdaCodecSxWakeCapability;
/** Offset 0x00C9 - Enable SATA
Enable/disable SATA controller.
$EN_DIS
**/
UINT8 SataEnable;
/** Offset 0x00CA - SATA Mode
Select SATA controller working mode.
0:AHCI, 1:RAID
**/
UINT8 SataMode;
/** Offset 0x00CB - SPIn Device Mode
Selects SPI operation mode. N represents controller index: SPI0, SPI1, ... Available
modes: 0:SerialIoSpiDisabled, 1:SerialIoSpiPci, 2:SerialIoSpiHidden
**/
UINT8 SerialIoSpiMode[7];
/** Offset 0x00D2 - SPI<N> Chip Select Polarity
Sets polarity for each chip Select. Available options: 0:SerialIoSpiCsActiveLow,
1:SerialIoSpiCsActiveHigh
**/
UINT8 SerialIoSpiCsPolarity[14];
/** Offset 0x00E0 - SPI<N> Chip Select Enable
0:Disabled, 1:Enabled. Enables GPIO for CS0 or CS1 if it is Enabled
**/
UINT8 SerialIoSpiCsEnable[14];
/** Offset 0x00EE - SPIn Default Chip Select Output
Sets Default CS as Output. N represents controller index: SPI0, SPI1, ... Available
options: 0:CS0, 1:CS1
**/
UINT8 SerialIoSpiDefaultCsOutput[7];
/** Offset 0x00F5 - SPIn Default Chip Select Mode HW/SW
Sets Default CS Mode Hardware or Software. N represents controller index: SPI0,
SPI1, ... Available options: 0:HW, 1:SW
**/
UINT8 SerialIoSpiCsMode[7];
/** Offset 0x00FC - SPIn Default Chip Select State Low/High
Sets Default CS State Low or High. N represents controller index: SPI0, SPI1, ...
Available options: 0:Low, 1:High
**/
UINT8 SerialIoSpiCsState[7];
/** Offset 0x0103 - UARTn Device Mode
Selects Uart operation mode. N represents controller index: Uart0, Uart1, ... Available
modes: 0:SerialIoUartDisabled, 1:SerialIoUartPci, 2:SerialIoUartHidden, 3:SerialIoUartCom,
4:SerialIoUartSkipInit
**/
UINT8 SerialIoUartMode[7];
/** Offset 0x010A - Reserved
**/
UINT8 Reserved5[2];
/** Offset 0x010C - Default BaudRate for each Serial IO UART
Set default BaudRate Supported from 0 - default to 6000000
**/
UINT32 SerialIoUartBaudRate[7];
/** Offset 0x0128 - Default ParityType for each Serial IO UART
Set default Parity. 0: DefaultParity, 1: NoParity, 2: EvenParity, 3: OddParity
**/
UINT8 SerialIoUartParity[7];
/** Offset 0x012F - Default DataBits for each Serial IO UART
Set default word length. 0: Default, 5,6,7,8
**/
UINT8 SerialIoUartDataBits[7];
/** Offset 0x0136 - Default StopBits for each Serial IO UART
Set default stop bits. 0: DefaultStopBits, 1: OneStopBit, 2: OneFiveStopBits, 3:
TwoStopBits
**/
UINT8 SerialIoUartStopBits[7];
/** Offset 0x013D - Power Gating mode for each Serial IO UART that works in COM mode
Set Power Gating. 0: Disabled, 1: Enabled, 2: Auto
**/
UINT8 SerialIoUartPowerGating[7];
/** Offset 0x0144 - Enable Dma for each Serial IO UART that supports it
Set DMA/PIO mode. 0: Disabled, 1: Enabled
**/
UINT8 SerialIoUartDmaEnable[7];
/** Offset 0x014B - Enables UART hardware flow control, CTS and RTS lines
Enables UART hardware flow control, CTS and RTS lines.
**/
UINT8 SerialIoUartAutoFlow[7];
/** Offset 0x0152 - Reserved
**/
UINT8 Reserved6[2];
/** Offset 0x0154 - SerialIoUartRtsPinMuxPolicy
Select SerialIo Uart Rts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RTS*
for possible values.
**/
UINT32 SerialIoUartRtsPinMuxPolicy[7];
/** Offset 0x0170 - SerialIoUartCtsPinMuxPolicy
Select SerialIo Uart Cts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_CTS*
for possible values.
**/
UINT32 SerialIoUartCtsPinMuxPolicy[7];
/** Offset 0x018C - SerialIoUartRxPinMuxPolicy
Select SerialIo Uart Rx pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RX* for
possible values.
**/
UINT32 SerialIoUartRxPinMuxPolicy[7];
/** Offset 0x01A8 - SerialIoUartTxPinMuxPolicy
Select SerialIo Uart Tx pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_TX* for
possible values.
**/
UINT32 SerialIoUartTxPinMuxPolicy[7];
/** Offset 0x01C4 - UART Number For Debug Purpose
UART number for debug purpose. 0:UART0, 1:UART1, 2:UART2, 3:UART3, 4:UART4, 5:UART5,
6:UART6. Note: If UART0 is selected as CNVi BT Core interface, it cannot be used
for debug purpose.
0:UART0, 1:UART1, 2:UART2, 3:UART3, 4:UART4, 5:UART5, 6:UART6
**/
UINT8 SerialIoDebugUartNumber;
/** Offset 0x01C5 - Serial IO UART DBG2 table
Enable or disable Serial Io UART DBG2 table, default is Disable; <b>0: Disable;</b>
1: Enable.
**/
UINT8 SerialIoUartDbg2[7];
/** Offset 0x01CC - I2Cn Device Mode
Selects I2c operation mode. N represents controller index: I2c0, I2c1, ... Available
modes: 0:SerialIoI2cDisabled, 1:SerialIoI2cPci, 2:SerialIoI2cHidden
**/
UINT8 SerialIoI2cMode[8];
/** Offset 0x01D4 - Serial IO I2C SDA Pin Muxing
Select SerialIo I2c Sda pin muxing. Refer to GPIO_*_MUXING_SERIALIO_I2Cx_SDA* for
possible values.
**/
UINT32 PchSerialIoI2cSdaPinMux[8];
/** Offset 0x01F4 - Serial IO I2C SCL Pin Muxing
Select SerialIo I2c Scl pin muxing. Refer to GPIO_*_MUXING_SERIALIO_I2Cx_SCL* for
possible values.
**/
UINT32 PchSerialIoI2cSclPinMux[8];
/** Offset 0x0214 - PCH SerialIo I2C Pads Termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo I2C0,I2C1,... pads termination
respectively. One byte for each controller, byte0 for I2C0, byte1 for I2C1, and so on.
**/
UINT8 PchSerialIoI2cPadsTermination[8];
/** Offset 0x021C - ISH GP GPIO Pin Muxing
Determines ISH GP GPIO Pin muxing. See GPIO_*_MUXING_ISH_GP_x_GPIO_*. 'x' are GP_NUMBER
**/
UINT32 IshGpGpioPinMuxing[8];
/** Offset 0x023C - ISH UART Rx Pin Muxing
Determines ISH UART Rx Pin muxing. See GPIO_*_MUXING_ISH_UARTx_TXD_*
**/
UINT32 IshUartRxPinMuxing[3];
/** Offset 0x0248 - ISH UART Tx Pin Muxing
Determines ISH UART Tx Pin muxing. See GPIO_*_MUXING_ISH_UARTx_RXD_*
**/
UINT32 IshUartTxPinMuxing[3];
/** Offset 0x0254 - ISH UART Rts Pin Muxing
Select ISH UART Rts Pin muxing. Refer to GPIO_*_MUXING_ISH_UARTx_RTS_* for possible values.
**/
UINT32 IshUartRtsPinMuxing[3];
/** Offset 0x0260 - ISH UART Rts Pin Muxing
Select ISH UART Cts Pin muxing. Refer to GPIO_*_MUXING_ISH_UARTx_CTS_* for possible values.
**/
UINT32 IshUartCtsPinMuxing[3];
/** Offset 0x026C - ISH I2C SDA Pin Muxing
Select ISH I2C SDA Pin muxing. Refer to GPIO_*_MUXING_ISH_I2Cx_SDA_* for possible values.
**/
UINT32 IshI2cSdaPinMuxing[3];
/** Offset 0x0278 - ISH I2C SCL Pin Muxing
Select ISH I2C SCL Pin muxing. Refer to GPIO_*_MUXING_ISH_I2Cx_SCL_* for possible values.
**/
UINT32 IshI2cSclPinMuxing[3];
/** Offset 0x0284 - ISH SPI MOSI Pin Muxing
Select ISH SPI MOSI Pin muxing. Refer to GPIO_*_MUXING_ISH_SPIx_MOSI_* for possible values.
**/
UINT32 IshSpiMosiPinMuxing[2];
/** Offset 0x028C - ISH SPI MISO Pin Muxing
Select ISH SPI MISO Pin muxing. Refer to GPIO_*_MUXING_ISH_SPIx_MISO_* for possible values.
**/
UINT32 IshSpiMisoPinMuxing[2];
/** Offset 0x0294 - ISH SPI CLK Pin Muxing
Select ISH SPI CLK Pin muxing. Refer to GPIO_*_MUXING_ISH_SPIx_CLK_* for possible values.
**/
UINT32 IshSpiClkPinMuxing[2];
/** Offset 0x029C - ISH SPI CS#N Pin Muxing
Select ISH SPI CS#N Pin muxing. Refer to GPIO_*_MUXING_ISH_SPIx_CS<N>_* for possible
values. N-SPI number, 0-1.
**/
UINT32 IshSpiCsPinMuxing[4];
/** Offset 0x02AC - ISH GP GPIO Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo GP#N GPIO pads termination
respectively. #N are GP_NUMBER, not strictly relate to indexes of this table. Index
0-23 -> ISH_GP_0-23, Index 24-25 -> ISH_GP_30-31
**/
UINT8 IshGpGpioPadTermination[8];
/** Offset 0x02B4 - ISH UART Rx Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo UART#N Rx pads termination
respectively. #N-byte for each controller, byte0 for UART0 Rx, byte1 for UART1
Rx, and so on.
**/
UINT8 IshUartRxPadTermination[3];
/** Offset 0x02B7 - ISH UART Tx Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo UART#N Tx pads termination
respectively. #N-byte for each controller, byte0 for UART0 Tx, byte1 for UART1
Tx, and so on.
**/
UINT8 IshUartTxPadTermination[3];
/** Offset 0x02BA - ISH UART Rts Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo UART#N Rts pads termination
respectively. #N-byte for each controller, byte0 for UART0 Rts, byte1 for UART1
Rts, and so on.
**/
UINT8 IshUartRtsPadTermination[3];
/** Offset 0x02BD - ISH UART Rts Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo UART#N Cts pads termination
respectively. #N-byte for each controller, byte0 for UART0 Cts, byte1 for UART1
Cts, and so on.
**/
UINT8 IshUartCtsPadTermination[3];
/** Offset 0x02C0 - ISH I2C SDA Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo I2C#N Sda pads termination
respectively. #N-byte for each controller, byte0 for I2C0 Sda, byte1 for I2C1 Sda,
and so on.
**/
UINT8 IshI2cSdaPadTermination[3];
/** Offset 0x02C3 - ISH I2C SCL Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo I2C#N Scl pads termination
respectively. #N-byte for each controller, byte0 for I2C0 Scl, byte1 for I2C1 Scl,
and so on.
**/
UINT8 IshI2cSclPadTermination[3];
/** Offset 0x02C6 - ISH SPI MOSI Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo SPI#N Mosi pads termination
respectively. #N-byte for each controller, byte0 for SPI0 Mosi, byte1 for SPI1
Mosi, and so on.
**/
UINT8 IshSpiMosiPadTermination[2];
/** Offset 0x02C8 - ISH SPI MISO Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo SPI#N Miso pads termination
respectively. #N-byte for each controller, byte0 for SPI0 Miso, byte1 for SPI1
Miso, and so on.
**/
UINT8 IshSpiMisoPadTermination[2];
/** Offset 0x02CA - ISH SPI CLK Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo SPI#N Clk pads termination
respectively. #N-byte for each controller, byte0 for SPI0 Clk, byte1 for SPI1 Clk,
and so on.
**/
UINT8 IshSpiClkPadTermination[2];
/** Offset 0x02CC - ISH SPI CS#N Pad termination
0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
0x19: 20kOhm weak pull-up - Enable/disable SerialIo SPI#N Cs#M pads termination
respectively. N*M-byte for each controller, byte0 for SPI0 Cs0, byte1 for SPI1
Cs1, SPI1 Cs0, byte2, SPI1 Cs1, byte3
**/
UINT8 IshSpiCsPadTermination[4];
/** Offset 0x02D0 - Enable PCH ISH SPI Cs#N pins assigned
Set if ISH SPI Cs#N pins are to be enabled by BIOS. 0: Disable; 1: Enable. N-Cs
number: 0-1
**/
UINT8 PchIshSpiCsEnable[4];
/** Offset 0x02D4 - USB Per Port HS Preemphasis Bias
USB Per Port HS Preemphasis Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV,
100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV. One byte for each port.
**/
UINT8 Usb2PhyPetxiset[16];
/** Offset 0x02E4 - USB Per Port HS Transmitter Bias
USB Per Port HS Transmitter Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV,
100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV, One byte for each port.
**/
UINT8 Usb2PhyTxiset[16];
/** Offset 0x02F4 - USB Per Port HS Transmitter Emphasis
USB Per Port HS Transmitter Emphasis. 00b - Emphasis OFF, 01b - De-emphasis ON,
10b - Pre-emphasis ON, 11b - Pre-emphasis & De-emphasis ON. One byte for each port.
**/
UINT8 Usb2PhyPredeemp[16];
/** Offset 0x0304 - USB Per Port Half Bit Pre-emphasis
USB Per Port Half Bit Pre-emphasis. 1b - half-bit pre-emphasis, 0b - full-bit pre-emphasis.
One byte for each port.
**/
UINT8 Usb2PhyPehalfbit[16];
/** Offset 0x0314 - Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment
Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment. Each value
in arrary can be between 0-1. One byte for each port.
**/
UINT8 Usb3HsioTxDeEmphEnable[10];
/** Offset 0x031E - USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting
USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting, HSIO_TX_DWORD5[21:16],
<b>Default = 29h</b> (approximately -3.5dB De-Emphasis). One byte for each port.
**/
UINT8 Usb3HsioTxDeEmph[10];
/** Offset 0x0328 - Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment
Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment, Each value
in arrary can be between 0-1. One byte for each port.
**/
UINT8 Usb3HsioTxDownscaleAmpEnable[10];
/** Offset 0x0332 - USB 3.0 TX Output Downscale Amplitude Adjustment
USB 3.0 TX Output Downscale Amplitude Adjustment, HSIO_TX_DWORD8[21:16], <b>Default
= 00h</b>. One byte for each port.
**/
UINT8 Usb3HsioTxDownscaleAmp[10];
/** Offset 0x033C
**/
UINT8 PchUsb3HsioCtrlAdaptOffsetCfgEnable[10];
/** Offset 0x0346
**/
UINT8 PchUsb3HsioFilterSelNEnable[10];
/** Offset 0x0350
**/
UINT8 PchUsb3HsioFilterSelPEnable[10];
/** Offset 0x035A
**/
UINT8 PchUsb3HsioOlfpsCfgPullUpDwnResEnable[10];
/** Offset 0x0364
**/
UINT8 PchUsb3HsioCtrlAdaptOffsetCfg[10];
/** Offset 0x036E
**/
UINT8 PchUsb3HsioOlfpsCfgPullUpDwnRes[10];
/** Offset 0x0378
**/
UINT8 PchUsb3HsioFilterSelN[10];
/** Offset 0x0382
**/
UINT8 PchUsb3HsioFilterSelP[10];
/** Offset 0x038C - Enable LAN
Enable/disable LAN controller.
$EN_DIS
**/
UINT8 PchLanEnable;
/** Offset 0x038D - Enable PCH TSN
Enable/disable TSN on the PCH.
$EN_DIS
**/
UINT8 PchTsnEnable;
/** Offset 0x038E - TSN Link Speed
Set TSN Link Speed.
0: 24Mhz 2.5Gbps, 1: 24Mhz 1Gbps, 2: 38.4Mhz 2.5Gbps, 3: 38.4Mhz 1Gbps
**/
UINT8 PchTsnLinkSpeed;
/** Offset 0x038F - Reserved
**/
UINT8 Reserved7;
/** Offset 0x0390 - Reserved
**/
UINT32 Reserved8;
/** Offset 0x0394 - Reserved
**/
UINT32 Reserved9;
/** Offset 0x0398 - PCIe PTM enable/disable
Enable/disable Precision Time Measurement for PCIE Root Ports.
**/
UINT8 PciePtm[28];
/** Offset 0x03B4 - PCIe DPC enable/disable
Enable/disable Downstream Port Containment for PCIE Root Ports.
**/
UINT8 PcieDpc[28];
/** Offset 0x03D0 - PCIe DPC extensions enable/disable
Enable/disable Downstream Port Containment Extensions for PCIE Root Ports.
**/
UINT8 PcieEdpc[28];
/** Offset 0x03EC - USB PDO Programming
Enable/disable PDO programming for USB in PEI phase. Disabling will allow for programming
during later phase. 1: enable, 0: disable
$EN_DIS
**/
UINT8 UsbPdoProgramming;
/** Offset 0x03ED - Reserved
**/
UINT8 Reserved10[3];
/** Offset 0x03F0 - Power button debounce configuration
Debounce time for PWRBTN in microseconds. For values not supported by HW, they will
be rounded down to closest supported on. 0: disable, 250-1024000us: supported range
**/
UINT32 PmcPowerButtonDebounce;
/** Offset 0x03F4 - PCH eSPI Host and Device BME enabled
PCH eSPI Host and Device BME enabled
$EN_DIS
**/
UINT8 PchEspiBmeMasterSlaveEnabled;
/** Offset 0x03F5 - PCH eSPI Link Configuration Lock (SBLCL)
Enable/Disable lock of communication through SET_CONFIG/GET_CONFIG to eSPI slaves
addresseses from range 0x0 - 0x7FF
$EN_DIS
**/
UINT8 PchEspiLockLinkConfiguration;
/** Offset 0x03F6 - Mask to enable the usage of external V1p05 VR rail in specific S0ix or Sx states
Enable External V1P05 Rail in: BIT0:S0i1/S0i2, BIT1:S0i3, BIT2:S3, BIT3:S4, BIT4:S5, BIT5:S0
**/
UINT8 PchFivrExtV1p05RailEnabledStates;
/** Offset 0x03F7 - Mask to enable the platform configuration of external V1p05 VR rail
External V1P05 Rail Supported Configuration
**/
UINT8 PchFivrExtV1p05RailSupportedVoltageStates;
/** Offset 0x03F8 - External V1P05 Voltage Value that will be used in S0i2/S0i3 states
Value is given in 2.5mV increments (0=0mV, 1=2.5mV, 2=5mV...)
**/
UINT16 PchFivrExtV1p05RailVoltage;
/** Offset 0x03FA - External V1P05 Icc Max Value
Granularity of this setting is 1mA and maximal possible value is 200mA
**/
UINT8 PchFivrExtV1p05RailIccMax;
/** Offset 0x03FB - Mask to enable the usage of external Vnn VR rail in specific S0ix or Sx states
Enable External Vnn Rail in: BIT0:S0i1/S0i2, BIT1:S0i3, BIT2:S3, BIT3:S4, BIT5:S5
**/
UINT8 PchFivrExtVnnRailEnabledStates;
/** Offset 0x03FC - Mask to enable the platform configuration of external Vnn VR rail
External Vnn Rail Supported Configuration
**/
UINT8 PchFivrExtVnnRailSupportedVoltageStates;
/** Offset 0x03FD - Reserved
**/
UINT8 Reserved11;
/** Offset 0x03FE - External Vnn Voltage Value that will be used in S0ix/Sx states
Value is given in 2.5mV increments (0=0mV, 1=2.5mV, 2=5mV...), Default is set to 420
**/
UINT16 PchFivrExtVnnRailVoltage;
/** Offset 0x0400 - External Vnn Icc Max Value that will be used in S0ix/Sx states
Granularity of this setting is 1mA and maximal possible value is 200mA
**/
UINT8 PchFivrExtVnnRailIccMax;
/** Offset 0x0401 - Mask to enable the usage of external Vnn VR rail in Sx states
Use only if Ext Vnn Rail config is different in Sx. Enable External Vnn Rail in
Sx: BIT0-1:Reserved, BIT2:S3, BIT3:S4, BIT4:S5, BIT5:S0
**/
UINT8 PchFivrExtVnnRailSxEnabledStates;
/** Offset 0x0402 - External Vnn Voltage Value that will be used in Sx states
Use only if Ext Vnn Rail config is different in Sx. Value is given in 2.5mV increments
(0=0mV, 1=2.5mV, 2=5mV...)
**/
UINT16 PchFivrExtVnnRailSxVoltage;
/** Offset 0x0404 - External Vnn Icc Max Value that will be used in Sx states
Use only if Ext Vnn Rail config is different in Sx. Granularity of this setting
is 1mA and maximal possible value is 200mA
**/
UINT8 PchFivrExtVnnRailSxIccMax;
/** Offset 0x0405 - Transition time in microseconds from Low Current Mode Voltage to High Current Mode Voltage
This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX
to low current mode voltage.
**/
UINT8 PchFivrVccinAuxLowToHighCurModeVolTranTime;
/** Offset 0x0406 - Transition time in microseconds from Retention Mode Voltage to High Current Mode Voltage
This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX
to retention mode voltage.
**/
UINT8 PchFivrVccinAuxRetToHighCurModeVolTranTime;
/** Offset 0x0407 - Transition time in microseconds from Retention Mode Voltage to Low Current Mode Voltage
This field has 1us resolution. When value is 0 PCH will not transition VCCIN_AUX
to retention mode voltage.
**/
UINT8 PchFivrVccinAuxRetToLowCurModeVolTranTime;
/** Offset 0x0408 - Transition time in microseconds from Off (0V) to High Current Mode Voltage
This field has 1us resolution. When value is 0 Transition to 0V is disabled.
**/
UINT16 PchFivrVccinAuxOffToHighCurModeVolTranTime;
/** Offset 0x040A - PMC Debug Message Enable
When Enabled, PMC HW will send debug messages to trace hub; When Disabled, PMC HW
will never send debug meesages to trace hub. Noted: When Enabled, may not enter S0ix
$EN_DIS
**/
UINT8 PmcDbgMsgEn;
/** Offset 0x040B - Reserved
**/
UINT8 Reserved12;
/** Offset 0x040C - Pointer of ChipsetInit Binary
ChipsetInit Binary Pointer.
**/
UINT32 ChipsetInitBinPtr;
/** Offset 0x0410 - Length of ChipsetInit Binary
ChipsetInit Binary Length.
**/
UINT32 ChipsetInitBinLen;
/** Offset 0x0414 - FIVR Dynamic Power Management
Enable/Disable FIVR Dynamic Power Management.
$EN_DIS
**/
UINT8 PchFivrDynPm;
/** Offset 0x0415 - Reserved
**/
UINT8 Reserved13;
/** Offset 0x0416 - External V1P05 Icc Max Value
Granularity of this setting is 1mA and maximal possible value is 500mA
**/
UINT16 PchFivrExtV1p05RailIccMaximum;
/** Offset 0x0418 - External Vnn Icc Max Value that will be used in S0ix/Sx states
Granularity of this setting is 1mA and maximal possible value is 500mA
**/
UINT16 PchFivrExtVnnRailIccMaximum;
/** Offset 0x041A - External Vnn Icc Max Value that will be used in Sx states
Use only if Ext Vnn Rail config is different in Sx. Granularity of this setting
is 1mA and maximal possible value is 500mA
**/
UINT16 PchFivrExtVnnRailSxIccMaximum;
/** Offset 0x041C - Extented BIOS Direct Read Decode enable
Enable/Disable access to bigger than 16MB BIOS Region through Direct Memory Reads.
0: disabled (default), 1: enabled
$EN_DIS
**/
UINT8 PchSpiExtendedBiosDecodeRangeEnable;
/** Offset 0x041D - Reserved
**/
UINT8 Reserved14[3];
/** Offset 0x0420 - Extended BIOS Direct Read Decode Range base
Bits of 31:16 of a memory address that'll be a base for Extended BIOS Direct Read Decode.
**/
UINT32 PchSpiExtendedBiosDecodeRangeBase;
/** Offset 0x0424 - Extended BIOS Direct Read Decode Range limit
Bits of 31:16 of a memory address that'll be a limit for Extended BIOS Direct Read Decode.
**/
UINT32 PchSpiExtendedBiosDecodeRangeLimit;
/** Offset 0x0428 - Reserved
**/
UINT8 Reserved15;
/** Offset 0x0429 - Reserved
**/
UINT8 Reserved16[3];
/** Offset 0x042C - Reserved
**/
UINT32 Reserved17;
/** Offset 0x0430 - Reserved
**/
UINT32 Reserved18;
/** Offset 0x0434 - CNVi Configuration
This option allows for automatic detection of Connectivity Solution. [Auto Detection]
assumes that CNVi will be enabled when available, [Disable] allows for disabling CNVi.
0:Disable, 1:Auto
**/
UINT8 CnviMode;
/** Offset 0x0435 - Reserved
**/
UINT8 Reserved19;
/** Offset 0x0436 - CNVi BT Core
Enable/Disable CNVi BT Core, Default is ENABLE. 0: DISABLE, 1: ENABLE
$EN_DIS
**/
UINT8 CnviBtCore;
/** Offset 0x0437 - CNVi BT Audio Offload
Enable/Disable BT Audio Offload, Default is DISABLE. 0: DISABLE, 1: ENABLE
$EN_DIS
**/
UINT8 CnviBtAudioOffload;
/** Offset 0x0438 - CNVi RF_RESET pin muxing
Select CNVi RF_RESET# pin depending on board routing. ADP-P/M: GPP_A8 = 0x2942E408(default)
or GPP_F4 = 0x194CE404. ADP-S: 0. Refer to GPIO_*_MUXING_CNVI_RF_RESET_* in GpioPins*.h.
**/
UINT32 CnviRfResetPinMux;
/** Offset 0x043C - CNVi CLKREQ pin muxing
Select CNVi CLKREQ pin depending on board routing. ADP-P/M: GPP_A9 = 0x3942E609(default)
or GPP_F5 = 0x394CE605. ADP-S: 0. Refer to GPIO_*_MUXING_CNVI_CRF_XTAL_CLKREQ_*
in GpioPins*.h.
**/
UINT32 CnviClkreqPinMux;
/** Offset 0x0440 - Enable Host C10 reporting through eSPI
Enable/disable Host C10 reporting to Device via eSPI Virtual Wire.
$EN_DIS
**/
UINT8 PchEspiHostC10ReportEnable;
/** Offset 0x0441 - PCH USB2 PHY Power Gating enable
1: Will enable USB2 PHY SUS Well Power Gating, 0: Will not enable PG of USB2 PHY
Sus Well PG
$EN_DIS
**/
UINT8 PmcUsb2PhySusPgEnable;
/** Offset 0x0442 - PCH USB OverCurrent mapping enable
1: Will program USB OC pin mapping in xHCI controller memory, 0: Will clear OC pin
mapping allow for NOA usage of OC pins
$EN_DIS
**/
UINT8 PchUsbOverCurrentEnable;
/** Offset 0x0443 - Espi Lgmr Memory Range decode
This option enables or disables espi lgmr
$EN_DIS
**/
UINT8 PchEspiLgmrEnable;
/** Offset 0x0444 - External V1P05 Control Ramp Timer value
Hold off time to be used when changing the v1p05_ctrl for external bypass value in us
**/
UINT8 PchFivrExtV1p05RailCtrlRampTmr;
/** Offset 0x0445 - External VNN Control Ramp Timer value
Hold off time to be used when changing the vnn_ctrl for external bypass value in us
**/
UINT8 PchFivrExtVnnRailCtrlRampTmr;
/** Offset 0x0446 - Set SATA DEVSLP GPIO Reset Config
Set SATA DEVSLP GPIO Reset Config per port. 0x00 - GpioResetDefault, 0x01 - GpioResumeReset,
0x03 - GpioHostDeepReset, 0x05 - GpioPlatformReset, 0x07 - GpioDswReset. One byte
for each port, byte0 for port0, byte1 for port1, and so on.
**/
UINT8 SataPortsDevSlpResetConfig[8];
/** Offset 0x044E - PCHHOT# pin
Enable PCHHOT# pin assertion when temperature is higher than PchHotLevel. 0: disable, 1: enable
$EN_DIS
**/
UINT8 PchHotEnable;
/** Offset 0x044F - SATA LED
SATA LED indicating SATA controller activity. 0: disable, 1: enable
$EN_DIS
**/
UINT8 SataLedEnable;
/** Offset 0x0450 - VRAlert# Pin
When VRAlert# feature pin is enabled and its state is '0', the PMC requests throttling
to a T3 Tstate to the PCH throttling unit.. 0: disable, 1: enable
$EN_DIS
**/
UINT8 PchPmVrAlert;
/** Offset 0x0451 - AMT Switch
Enable/Disable. 0: Disable, 1: enable, Enable or disable AMT functionality.
$EN_DIS
**/
UINT8 AmtEnabled;
/** Offset 0x0452 - WatchDog Timer Switch
Enable/Disable. 0: Disable, 1: enable, Enable or disable WatchDog timer. Setting
is invalid if AmtEnabled is 0.
$EN_DIS
**/
UINT8 WatchDogEnabled;
/** Offset 0x0453 - PET Progress
Enable/Disable. 0: Disable, 1: enable, Enable/Disable PET Events Progress to receive
PET Events. Setting is invalid if AmtEnabled is 0.
$EN_DIS
**/
UINT8 FwProgress;
/** Offset 0x0454 - SOL Switch
Enable/Disable. 0: Disable, 1: enable, Serial Over Lan enable/disable state by Mebx.
Setting is invalid if AmtEnabled is 0.
$EN_DIS
**/
UINT8 AmtSolEnabled;
/** Offset 0x0455 - Reserved
**/
UINT8 Reserved20;
/** Offset 0x0456 - OS Timer
16 bits Value, Set OS watchdog timer. Setting is invalid if AmtEnabled is 0.
**/
UINT16 WatchDogTimerOs;
/** Offset 0x0458 - BIOS Timer
16 bits Value, Set BIOS watchdog timer. Setting is invalid if AmtEnabled is 0.
**/
UINT16 WatchDogTimerBios;
/** Offset 0x045A - Force MEBX execution
Enable/Disable. 0: Disable, 1: enable, Force MEBX execution.
$EN_DIS
**/
UINT8 ForcMebxSyncUp;
/** Offset 0x045B - PCH PCIe root port connection type
0: built-in device, 1:slot
**/
UINT8 PcieRpSlotImplemented[28];
/** Offset 0x0477 - PCIE RP Access Control Services Extended Capability
Enable/Disable PCIE RP Access Control Services Extended Capability
**/
UINT8 PcieRpAcsEnabled[28];
/** Offset 0x0493 - PCIE RP Clock Power Management
Enable/Disable PCIE RP Clock Power Management, even if disabled, CLKREQ# signal
can still be controlled by L1 PM substates mechanism
**/
UINT8 PcieRpEnableCpm[28];
/** Offset 0x04AF - Reserved
**/
UINT8 Reserved21[1];
/** Offset 0x04B0 - PCIE RP Detect Timeout Ms
The number of milliseconds within 0~65535 in reference code will wait for link to
exit Detect state for enabled ports before assuming there is no device and potentially
disabling the port.
**/
UINT16 PcieRpDetectTimeoutMs[28];
/** Offset 0x04E8 - ModPHY SUS Power Domain Dynamic Gating
Enable/Disable ModPHY SUS Power Domain Dynamic Gating. Setting not supported on
PCH-H. 0: disable, 1: enable
$EN_DIS
**/
UINT8 PmcModPhySusPgEnable;
/** Offset 0x04E9 - V1p05-PHY supply external FET control
Enable/Disable control using EXT_PWR_GATE# pin of external FET to power gate v1p05-PHY
supply. 0: disable, 1: enable
$EN_DIS
**/
UINT8 PmcV1p05PhyExtFetControlEn;
/** Offset 0x04EA - V1p05-IS supply external FET control
Enable/Disable control using EXT_PWR_GATE2# pin of external FET to power gate v1p05-IS
supply. 0: disable, 1: enable
$EN_DIS
**/
UINT8 PmcV1p05IsExtFetControlEn;
/** Offset 0x04EB - Enable/Disable PavpEnable
Enable(Default): Enable PavpEnable, Disable: Disable PavpEnable
$EN_DIS
**/
UINT8 PavpEnable;
/** Offset 0x04EC - CdClock Frequency selection
0 (Default) Auto (Max based on reference clock frequency), 0: 192, 1: 307.2, 2:
312 Mhz, 3: 324Mhz, 4: 326.4 Mhz, 5: 552 Mhz, 6: 556.8 Mhz, 7: 648 Mhz, 8: 652.8 Mhz
0xFF: Auto (Max based on reference clock frequency), 0: 192, 1: 307.2, 2: 312 Mhz,
3: 324Mhz, 4: 326.4 Mhz, 5: 552 Mhz, 6: 556.8 Mhz, 7: 648 Mhz, 8: 652.8 Mhz
**/
UINT8 CdClock;
/** Offset 0x04ED - Enable/Disable PeiGraphicsPeimInit
<b>Enable(Default):</b> FSP will initialize the framebuffer and provide it via EFI_PEI_GRAPHICS_INFO_HOB.
Disable: FSP will NOT initialize the framebuffer.
$EN_DIS
**/
UINT8 PeiGraphicsPeimInit;
/** Offset 0x04EE - Enable D3 Hot in TCSS
This policy will enable/disable D3 hot support in IOM
$EN_DIS
**/
UINT8 D3HotEnable;
/** Offset 0x04EF - Enable or disable GNA device
0=Disable, 1(Default)=Enable
$EN_DIS
**/
UINT8 GnaEnable;
/** Offset 0x04F0 - TypeC port GPIO setting
GPIO Ping number for Type C Aux Oritation setting, use the GpioPad that is defined
in GpioPinsXXXH.h and GpioPinsXXXLp.h as argument.(XXX is platform name, Ex: Adl
= AlderLake)
**/
UINT32 IomTypeCPortPadCfg[8];
/** Offset 0x0510 - CPU USB3 Port Over Current Pin
Describe the specific over current pin number of USBC Port N.
**/
UINT8 CpuUsb3OverCurrentPin[8];
/** Offset 0x0518 - Enable D3 Cold in TCSS
This policy will enable/disable D3 cold support in IOM
$EN_DIS
**/
UINT8 D3ColdEnable;
/** Offset 0x0519 - Enable/Disable PCIe tunneling for USB4
Enable/Disable PCIe tunneling for USB4, default is enable
$EN_DIS
**/
UINT8 ITbtPcieTunnelingForUsb4;
/** Offset 0x051A - Enable/Disable SkipFspGop
Enable: Skip FSP provided GOP driver, Disable(Default): Use FSP provided GOP driver
$EN_DIS
**/
UINT8 SkipFspGop;
/** Offset 0x051B - TC State in TCSS
This TC C-State Limit in IOM
**/
UINT8 TcCstateLimit;
/** Offset 0x051C - Intel Graphics VBT (Video BIOS Table) Size
Size of Internal Graphics VBT Image
**/
UINT32 VbtSize;
/** Offset 0x0520 - Platform LID Status for LFP Displays.
LFP Display Lid Status (LID_STATUS enum): 0 (Default): LidClosed, 1: LidOpen.
0: LidClosed, 1: LidOpen
**/
UINT8 LidStatus;
/** Offset 0x0521 - Reserved
**/
UINT8 Reserved22;
/** Offset 0x0522 - Reserved
**/
UINT8 Reserved23;
/** Offset 0x0523 - Reserved
**/
UINT8 Reserved24[5];
/** Offset 0x0528 - Reserved
**/
UINT8 Reserved25;
/** Offset 0x0529 - Enable VMD controller
Enable/disable to VMD controller.0: Disable; 1: Enable(Default)
$EN_DIS
**/
UINT8 VmdEnable;
/** Offset 0x052A - Map port under VMD
Map/UnMap port under VMD
$EN_DIS
**/
UINT8 VmdPort[31];
/** Offset 0x0549 - VMD Port Device
VMD Root port device number.
**/
UINT8 VmdPortDev[31];
/** Offset 0x0568 - VMD Port Func
VMD Root port function number.
**/
UINT8 VmdPortFunc[31];
/** Offset 0x0587 - VMD Config Bar size
Set The VMD Config Bar Size.
**/
UINT8 VmdCfgBarSize;
/** Offset 0x0588 - VMD Config Bar Attributes
0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH(Default), 2: VMD_64BIT_PREFETCH
0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH
**/
UINT8 VmdCfgBarAttr;
/** Offset 0x0589 - VMD Mem Bar1 size
Set The VMD Mem Bar1 Size.
**/
UINT8 VmdMemBarSize1;
/** Offset 0x058A - VMD Mem Bar1 Attributes
0: VMD_32BIT_NONPREFETCH(Default), 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH
0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH
**/
UINT8 VmdMemBar1Attr;
/** Offset 0x058B - VMD Mem Bar2 size
Set The VMD Mem Bar2 Size.
**/
UINT8 VmdMemBarSize2;
/** Offset 0x058C - VMD Mem Bar2 Attributes
0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH(Default), 2: VMD_64BIT_PREFETCH
0: VMD_32BIT_NONPREFETCH, 1: VMD_64BIT_NONPREFETCH, 2: VMD_64BIT_PREFETCH
**/
UINT8 VmdMemBar2Attr;
/** Offset 0x058D - Reserved
**/
UINT8 Reserved26[3];
/** Offset 0x0590 - VMD Variable
VMD Variable Pointer.
**/
UINT32 VmdVariablePtr;
/** Offset 0x0594 - Temporary CfgBar address for VMD
VMD Variable Pointer.
**/
UINT32 VmdCfgBarBase;
/** Offset 0x0598 - Temporary MemBar1 address for VMD
VMD Variable Pointer.
**/
UINT32 VmdMemBar1Base;
/** Offset 0x059C - Temporary MemBar2 address for VMD
VMD Variable Pointer.
**/
UINT32 VmdMemBar2Base;
/** Offset 0x05A0 - Reserved
**/
UINT8 Reserved27;
/** Offset 0x05A1 - Enable/Disable PMC-PD Solution
This policy will enable/disable PMC-PD Solution vs EC-TCPC Solution
$EN_DIS
**/
UINT8 PmcPdEnable;
/** Offset 0x05A2 - TCSS Aux Orientation Override Enable
Bits 0, 2, ... 10 control override enables, bits 1, 3, ... 11 control overrides
**/
UINT16 TcssAuxOri;
/** Offset 0x05A4 - TCSS HSL Orientation Override Enable
Bits 0, 2, ... 10 control override enables, bits 1, 3, ... 11 control overrides
**/
UINT16 TcssHslOri;
/** Offset 0x05A6 - USB override in IOM
This policy will enable/disable USB Connect override in IOM
$EN_DIS
**/
UINT8 UsbOverride;
/** Offset 0x05A7 - ITBT Root Port Enable
ITBT Root Port Enable, 0:Disable, 1:Enable
0:Disable, 1:Enable
**/
UINT8 ITbtPcieRootPortEn[4];
/** Offset 0x05AB - TCSS USB Port Enable
Bits 0, 1, ... max Type C port control enables
**/
UINT8 UsbTcPortEn;
/** Offset 0x05AC - ITBTForcePowerOn Timeout value
ITBTForcePowerOn value. Specified increment values in miliseconds. Range is 0-1000.
100 = 100 ms.
**/
UINT16 ITbtForcePowerOnTimeoutInMs;
/** Offset 0x05AE - ITbtConnectTopology Timeout value
ITbtConnectTopologyTimeout value. Specified increment values in miliseconds. Range
is 0-10000. 100 = 100 ms.
**/
UINT16 ITbtConnectTopologyTimeoutInMs;
/** Offset 0x05B0 - VCCST request for IOM
This policy will enable/disable VCCST and also decides if message would be replayed in S4/S5
$EN_DIS
**/
UINT8 VccSt;
/** Offset 0x05B1 - Reserved
**/
UINT8 Reserved28[1];
/** Offset 0x05B2 - ITBT DMA LTR
TCSS DMA1, DMA2 LTR value
**/
UINT16 ITbtDmaLtr[2];
/** Offset 0x05B6 - Reserved
**/
UINT8 Reserved29;
/** Offset 0x05B7 - Enable/Disable PTM
This policy will enable/disable Precision Time Measurement for TCSS PCIe Root Ports
$EN_DIS
**/
UINT8 PtmEnabled[4];
/** Offset 0x05BB - PCIE RP Ltr Enable
Latency Tolerance Reporting Mechanism.
**/
UINT8 SaPcieItbtRpLtrEnable[4];
/** Offset 0x05BF - PCIE RP Snoop Latency Override Mode
Latency Tolerance Reporting, Snoop Latency Override Mode.
**/
UINT8 SaPcieItbtRpSnoopLatencyOverrideMode[4];
/** Offset 0x05C3 - PCIE RP Snoop Latency Override Multiplier
Latency Tolerance Reporting, Snoop Latency Override Multiplier.
**/
UINT8 SaPcieItbtRpSnoopLatencyOverrideMultiplier[4];
/** Offset 0x05C7 - Reserved
**/
UINT8 Reserved30[1];
/** Offset 0x05C8 - PCIE RP Snoop Latency Override Value
Latency Tolerance Reporting, Snoop Latency Override Value.
**/
UINT16 SaPcieItbtRpSnoopLatencyOverrideValue[4];
/** Offset 0x05D0 - PCIE RP Non Snoop Latency Override Mode
Latency Tolerance Reporting, Non-Snoop Latency Override Mode.
**/
UINT8 SaPcieItbtRpNonSnoopLatencyOverrideMode[4];
/** Offset 0x05D4 - PCIE RP Non Snoop Latency Override Multiplier
Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier.
**/
UINT8 SaPcieItbtRpNonSnoopLatencyOverrideMultiplier[4];
/** Offset 0x05D8 - PCIE RP Non Snoop Latency Override Value
Latency Tolerance Reporting, Non-Snoop Latency Override Value.
**/
UINT16 SaPcieItbtRpNonSnoopLatencyOverrideValue[4];
/** Offset 0x05E0 - Force LTR Override
Force LTR Override.
**/
UINT8 SaPcieItbtRpForceLtrOverride[4];
/** Offset 0x05E4 - PCIE RP Ltr Config Lock
0: Disable; 1: Enable.
**/
UINT8 SaPcieItbtRpLtrConfigLock[4];
/** Offset 0x05E8 - Advanced Encryption Standard (AES) feature
Enable or Disable Advanced Encryption Standard (AES) feature; </b>0: Disable; <b>1: Enable
$EN_DIS
**/
UINT8 AesEnable;
/** Offset 0x05E9 - Power State 3 enable/disable
PCODE MMIO Mailbox: Power State 3 enable/disable; 0: Disable; <b>1: Enable</b>.
For all VR Indexes
**/
UINT8 Psi3Enable[5];
/** Offset 0x05EE - Power State 4 enable/disable
PCODE MMIO Mailbox: Power State 4 enable/disable; 0: Disable; <b>1: Enable</b>.For
all VR Indexes
**/
UINT8 Psi4Enable[5];
/** Offset 0x05F3 - Reserved
**/
UINT8 Reserved31[1];
/** Offset 0x05F4 - Imon slope correction
PCODE MMIO Mailbox: Imon slope correction. Specified in 1/100 increment values.
Range is 0-200. 125 = 1.25. <b>0: Auto</b>.For all VR Indexes
**/
UINT16 ImonSlope[5];
/** Offset 0x05FE - Imon offset correction
PCODE MMIO Mailbox: Imon offset correction. Value is a 2's complement signed integer.
Units 1/1000, Range 0-63999. For an offset = 12.580, use 12580. <b>0: Auto</b>
**/
UINT16 ImonOffset[5];
/** Offset 0x0608 - Enable/Disable BIOS configuration of VR
Enable/Disable BIOS configuration of VR; <b>0: Disable</b>; 1: Enable.For all VR Indexes
**/
UINT8 VrConfigEnable[5];
/** Offset 0x060D - Thermal Design Current enable/disable
PCODE MMIO Mailbox: Thermal Design Current enable/disable; <b>0: Disable</b>; 1:
Enable.For all VR Indexes
**/
UINT8 TdcEnable[5];
/** Offset 0x0612 - Reserved
**/
UINT8 Reserved32[2];
/** Offset 0x0614 - Thermal Design Current time window
PCODE MMIO Mailbox: Thermal Design Current time window. Defined in milli seconds.
Range 1ms to 448s
**/
UINT32 TdcTimeWindow[5];
/** Offset 0x0628 - Thermal Design Current Lock
PCODE MMIO Mailbox: Thermal Design Current Lock; <b>0: Disable</b>; 1: Enable.For
all VR Indexes
**/
UINT8 TdcLock[5];
/** Offset 0x062D - Platform Psys slope correction
PCODE MMIO Mailbox: Platform Psys slope correction. <b>0 - Auto</b> Specified in
1/100 increment values. Range is 0-200. 125 = 1.25
**/
UINT8 PsysSlope;
/** Offset 0x062E - Platform Psys offset correction
PCODE MMIO Mailbox: Platform Psys offset correction. <b>0 - Auto</b> Units 1/1000,
Range 0-63999. For an offset of 25.348, enter 25348.
**/
UINT16 PsysOffset;
/** Offset 0x0630 - Acoustic Noise Mitigation feature
Enable or Disable Acoustic Noise Mitigation feature. <b>0: Disabled</b>; 1: Enabled
$EN_DIS
**/
UINT8 AcousticNoiseMitigation;
/** Offset 0x0631 - Disable Fast Slew Rate for Deep Package C States for VR domains
Disable Fast Slew Rate for Deep Package C States based on Acoustic Noise Mitigation
feature enabled. <b>0: False</b>; 1: True
$EN_DIS
**/
UINT8 FastPkgCRampDisable[5];
/** Offset 0x0636 - Slew Rate configuration for Deep Package C States for VR domains
Slew Rate configuration for Deep Package C States for VR domains based on Acoustic
Noise Mitigation feature enabled. ADL supports VCCIA FAST/2/4/8/16, VCCGT FAST/2/4/8
and VCCSA FAST/2 <b>0: Fast/2</b>; 1: Fast/4; 2: Fast/8; 3: Fast/16
0: Fast/2, 1: Fast/4, 2: Fast/8, 3: Fast/16
**/
UINT8 SlowSlewRate[5];
/** Offset 0x063B - Reserved
**/
UINT8 Reserved33[1];
/** Offset 0x063C - Thermal Design Current current limit
PCODE MMIO Mailbox: Thermal Design Current current limit. Specified in 1/8A units.
Range is 0-4095. 1000 = 125A. <b>0: Auto</b>. For all VR Indexes
**/
UINT16 TdcCurrentLimit[5];
/** Offset 0x0646 - AcLoadline
PCODE MMIO Mailbox: AcLoadline in 1/100 mOhms (ie. 1250 = 12.50 mOhm); Range is
0-6249. <b>Intel Recommended Defaults vary by domain and SKU.
**/
UINT16 AcLoadline[5];
/** Offset 0x0650 - DcLoadline
PCODE MMIO Mailbox: DcLoadline in 1/100 mOhms (ie. 1250 = 12.50 mOhm); Range is
0-6249.<b>Intel Recommended Defaults vary by domain and SKU.</b>
**/
UINT16 DcLoadline[5];
/** Offset 0x065A - Power State 1 Threshold current
PCODE MMIO Mailbox: Power State 1 current cuttof in 1/4 Amp increments. Range is 0-128A.
**/
UINT16 Psi1Threshold[5];
/** Offset 0x0664 - Power State 2 Threshold current
PCODE MMIO Mailbox: Power State 2 current cuttof in 1/4 Amp increments. Range is 0-128A.
**/
UINT16 Psi2Threshold[5];
/** Offset 0x066E - Power State 3 Threshold current
PCODE MMIO Mailbox: Power State 3 current cuttof in 1/4 Amp increments. Range is 0-128A.
**/
UINT16 Psi3Threshold[5];
/** Offset 0x0678 - Icc Max limit
PCODE MMIO Mailbox: VR Icc Max limit. 0-512A in 1/4 A units. 400 = 100A
**/
UINT16 IccMax[5];
/** Offset 0x0682 - Enable or Disable TXT
Enable or Disable TXT; 0: Disable; <b>1: Enable</b>.
$EN_DIS
**/
UINT8 TxtEnable;
/** Offset 0x0683 - Skip Multi-Processor Initialization
When this is skipped, boot loader must initialize processors before SilicionInit
API. </b>0: Initialize; <b>1: Skip
$EN_DIS
**/
UINT8 SkipMpInit;
/** Offset 0x0684 - FIVR RFI Frequency
PCODE MMIO Mailbox: Set the desired RFI frequency, in increments of 100KHz. <b>0:
Auto</b>. Range varies based on XTAL clock: 0-1918 (Up to 191.8HMz) for 24MHz clock;
0-1535 (Up to 153.5MHz) for 19MHz clock.
**/
UINT16 FivrRfiFrequency;
/** Offset 0x0686 - FIVR RFI Spread Spectrum
Set the Spread Spectrum Range. <b>1.5%</b>; Range: 0.5%, 1%, 1.5%, 2%, 3%, 4%, 5%,
6%. Each Range is translated to an encoded value for FIVR register. 0.5% = 0, 1%
= 3, 1.5% = 8, 2% = 18, 3% = 28, 4% = 34, 5% = 39, 6% = 44.
**/
UINT8 FivrSpreadSpectrum;
/** Offset 0x0687 - Reserved
**/
UINT8 Reserved34;
/** Offset 0x0688 - CpuBistData
Pointer CPU BIST Data
**/
UINT32 CpuBistData;
/** Offset 0x068C - CpuMpPpi
<b>Optional</b> pointer to the boot loader's implementation of EFI_PEI_MP_SERVICES_PPI.
If not NULL, FSP will use the boot loader's implementation of multiprocessing.
See section 5.1.4 of the FSP Integration Guide for more details.
**/
UINT32 CpuMpPpi;
/** Offset 0x0690 - Pre Wake Randomization time
PCODE MMIO Mailbox: Acoustic Noise Mitigation Range.Defines the maximum pre-wake
randomization time in micro ticks.This can be programmed only if AcousticNoiseMitigation
is enabled. Range 0-255 <b>0</b>.
**/
UINT8 PreWake;
/** Offset 0x0691 - Ramp Up Randomization time
PCODE MMIO Mailbox: Acoustic Noise Mitigation Range.Defines the maximum Ramp Up
randomization time in micro ticks.This can be programmed only if AcousticNoiseMitigation
is enabled.Range 0-255 <b>0</b>.
**/
UINT8 RampUp;
/** Offset 0x0692 - Ramp Down Randomization time
PCODE MMIO Mailbox: Acoustic Noise Mitigation Range.Defines the maximum Ramp Down
randomization time in micro ticks.This can be programmed only if AcousticNoiseMitigation
is enabled.Range 0-255 <b>0</b>.
**/
UINT8 RampDown;
/** Offset 0x0693 - Reserved
**/
UINT8 Reserved35[1];
/** Offset 0x0694 - VR Voltage Limit
PCODE MMIO Mailbox: Voltage Limit. Range is 0 - 7999mV
**/
UINT16 VrVoltageLimit[5];
/** Offset 0x069E - VccIn Aux Imon IccMax
PCODE MMIO Mailbox: VccIn Aux Imon IccMax. <b>0 - Auto</b> Values are in 1/4 Amp
increments. Range is 0-512.
**/
UINT16 VccInAuxImonIccImax;
/** Offset 0x06A0 - Reserved
**/
UINT8 Reserved36;
/** Offset 0x06A1 - Reserved
**/
UINT8 Reserved37;
/** Offset 0x06A2 - Reserved
**/
UINT8 Reserved38;
/** Offset 0x06A3 - Reserved
**/
UINT8 Reserved39;
/** Offset 0x06A4 - Reserved
**/
UINT8 Reserved40;
/** Offset 0x06A5 - Reserved
**/
UINT8 Reserved41;
/** Offset 0x06A6 - Reserved
**/
UINT8 Reserved42;
/** Offset 0x06A7 - Reserved
**/
UINT8 Reserved43;
/** Offset 0x06A8 - Reserved
**/
UINT16 Reserved44;
/** Offset 0x06AA - FIVR RFI Spread Spectrum Enable or disable
Enable or Disable FIVR RFI Spread Spectrum. 0: Disable ; <b> 1: Enable </b>
**/
UINT8 FivrSpectrumEnable;
/** Offset 0x06AB - Reserved
**/
UINT8 Reserved45[1];
/** Offset 0x06AC - Reserved
**/
UINT16 Reserved46[5];
/** Offset 0x06B6 - Reserved
**/
UINT8 Reserved47[2];
/** Offset 0x06B8 - PpinSupport to view Protected Processor Inventory Number
Enable or Disable or Auto (Based on End of Manufacturing flag. Disabled if this
flag is set) for PPIN Support
0: Disable, 1: Enable, 2: Auto
**/
UINT8 PpinSupport;
/** Offset 0x06B9 - Enable or Disable Minimum Voltage Override
Enable or disable Minimum Voltage overrides ; <b>0: Disable</b>; 1: Enable.
$EN_DIS
**/
UINT8 EnableMinVoltageOverride;
/** Offset 0x06BA - Min Voltage for Runtime
PCODE MMIO Mailbox: Minimum voltage for runtime. Valid if EnableMinVoltageOverride
= 1. Range 0 to 1999mV. <b> 0: 0mV </b>
**/
UINT16 MinVoltageRuntime;
/** Offset 0x06BC - Reserved
**/
UINT8 Reserved48;
/** Offset 0x06BD - Reserved
**/
UINT8 Reserved49;
/** Offset 0x06BE - Min Voltage for C8
PCODE MMIO Mailbox: Minimum voltage for C8. Valid if EnableMinVoltageOverride =
1. Range 0 to 1999mV. <b> 0: 0mV </b>
**/
UINT16 MinVoltageC8;
/** Offset 0x06C0 - Smbios Type4 Max Speed Override
Provide the option for platform to override the MaxSpeed field of Smbios Type 4.
If this value is not zero, it dominates the field.
**/
UINT16 SmbiosType4MaxSpeedOverride;
/** Offset 0x06C2 - Current root mean square
PCODE MMIO Mailbox: Current root mean square; <b>0: Disable</b>; 1: Enable.For all
VR Indexes
**/
UINT8 Irms[5];
/** Offset 0x06C7 - AvxDisable
Enable or Disable AVX Support. This only applicable when all small core is disabled.
0: Enable, 1: Disable
**/
UINT8 AvxDisable;
/** Offset 0x06C8 - Avx3Disable
DEPRECATED
0: Enable, 1: Disable
**/
UINT8 Avx3Disable;
/** Offset 0x06C9 - Reserved
**/
UINT8 Reserved50;
/** Offset 0x06CA - CPU VR Power Delivery Design
Used to communicate the power delivery design capability of the board. This value
is an enum of the available power delivery segments that are defined in the Platform
Design Guide.
**/
UINT8 VrPowerDeliveryDesign;
/** Offset 0x06CB - Reserved
**/
UINT8 Reserved51[5];
/** Offset 0x06D0 - Reserved
**/
UINT32 Reserved52;
/** Offset 0x06D4 - Reserved
**/
UINT32 Reserved53;
/** Offset 0x06D8 - Reserved
**/
UINT32 Reserved54;
/** Offset 0x06DC - Reserved
**/
UINT32 Reserved55;
/** Offset 0x06E0 - Reserved
**/
UINT8 Reserved56[11];
/** Offset 0x06EB - Enable Power Optimizer
Enable DMI Power Optimizer on PCH side.
$EN_DIS
**/
UINT8 PchPwrOptEnable;
/** Offset 0x06EC - PCH Flash Protection Ranges Write Enble
Write or erase is blocked by hardware.
**/
UINT8 PchWriteProtectionEnable[5];
/** Offset 0x06F1 - PCH Flash Protection Ranges Read Enble
Read is blocked by hardware.
**/
UINT8 PchReadProtectionEnable[5];
/** Offset 0x06F6 - PCH Protect Range Limit
Left shifted address by 12 bits with address bits 11:0 are assumed to be FFFh for
limit comparison.
**/
UINT16 PchProtectedRangeLimit[5];
/** Offset 0x0700 - PCH Protect Range Base
Left shifted address by 12 bits with address bits 11:0 are assumed to be 0.
**/
UINT16 PchProtectedRangeBase[5];
/** Offset 0x070A - Enable Pme
Enable Azalia wake-on-ring.
$EN_DIS
**/
UINT8 PchHdaPme;
/** Offset 0x070B - HD Audio Link Frequency
HDA Link Freq (PCH_HDAUDIO_LINK_FREQUENCY enum): 0: 6MHz, 1: 12MHz, 2: 24MHz.
0: 6MHz, 1: 12MHz, 2: 24MHz
**/
UINT8 PchHdaLinkFrequency;
/** Offset 0x070C - Enable PCH ISH SPI Cs0 pins assigned
Set if ISH SPI Cs0 pins are to be enabled by BIOS. 0: Disable; 1: Enable.
**/
UINT8 PchIshSpiCs0Enable[1];
/** Offset 0x070D - Enable PCH Io Apic Entry 24-119
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchIoApicEntry24_119;
/** Offset 0x070E - PCH Io Apic ID
This member determines IOAPIC ID. Default is 0x02.
**/
UINT8 PchIoApicId;
/** Offset 0x070F - Enable PCH ISH SPI pins assigned
Set if ISH SPI native pins are to be enabled by BIOS. 0: Disable; 1: Enable.
**/
UINT8 PchIshSpiEnable[1];
/** Offset 0x0710 - Enable PCH ISH UART pins assigned
Set if ISH UART native pins are to be enabled by BIOS. 0: Disable; 1: Enable.
**/
UINT8 PchIshUartEnable[2];
/** Offset 0x0712 - Enable PCH ISH I2C pins assigned
Set if ISH I2C native pins are to be enabled by BIOS. 0: Disable; 1: Enable.
**/
UINT8 PchIshI2cEnable[3];
/** Offset 0x0715 - Enable PCH ISH GP pins assigned
Set if ISH GP native pins are to be enabled by BIOS. 0: Disable; 1: Enable.
**/
UINT8 PchIshGpEnable[8];
/** Offset 0x071D - PCH ISH PDT Unlock Msg
0: False; 1: True.
$EN_DIS
**/
UINT8 PchIshPdtUnlock;
/** Offset 0x071E - Enable PCH Lan LTR capabilty of PCH internal LAN
0: Disable; 1: Enable.
$EN_DIS
**/
UINT8 PchLanLtrEnable;
/** Offset 0x071F - Enable LOCKDOWN BIOS LOCK
Enable the BIOS Lock feature and set EISS bit (D31:F5:RegDCh[5]) for the BIOS region
protection.
$EN_DIS
**/
UINT8 PchLockDownBiosLock;
/** Offset 0x0720 - PCH Compatibility Revision ID
This member describes whether or not the CRID feature of PCH should be enabled.
$EN_DIS
**/
UINT8 PchCrid;
/** Offset 0x0721 - RTC BIOS Interface Lock
Enable RTC BIOS interface lock. When set, prevents RTC TS (BUC.TS) from being changed.
$EN_DIS
**/
UINT8 RtcBiosInterfaceLock;
/** Offset 0x0722 - RTC Cmos Memory Lock
Enable RTC lower and upper 128 byte Lock bits to lock Bytes 38h-3Fh in the upper
and and lower 128-byte bank of RTC RAM.
$EN_DIS
**/
UINT8 RtcMemoryLock;
/** Offset 0x0723 - Enable PCIE RP HotPlug
Indicate whether the root port is hot plug available.
**/
UINT8 PcieRpHotPlug[28];
/** Offset 0x073F - Enable PCIE RP Pm Sci
Indicate whether the root port power manager SCI is enabled.
**/
UINT8 PcieRpPmSci[28];
/** Offset 0x075B - Enable PCIE RP Transmitter Half Swing
Indicate whether the Transmitter Half Swing is enabled.
**/
UINT8 PcieRpTransmitterHalfSwing[28];
/** Offset 0x0777 - Enable PCIE RP Clk Req Detect
Probe CLKREQ# signal before enabling CLKREQ# based power management.
**/
UINT8 PcieRpClkReqDetect[28];
/** Offset 0x0793 - PCIE RP Advanced Error Report
Indicate whether the Advanced Error Reporting is enabled.
**/
UINT8 PcieRpAdvancedErrorReporting[28];
/** Offset 0x07AF - PCIE RP Unsupported Request Report
Indicate whether the Unsupported Request Report is enabled.
**/
UINT8 PcieRpUnsupportedRequestReport[28];
/** Offset 0x07CB - PCIE RP Fatal Error Report
Indicate whether the Fatal Error Report is enabled.
**/
UINT8 PcieRpFatalErrorReport[28];
/** Offset 0x07E7 - PCIE RP No Fatal Error Report
Indicate whether the No Fatal Error Report is enabled.
**/
UINT8 PcieRpNoFatalErrorReport[28];
/** Offset 0x0803 - PCIE RP Correctable Error Report
Indicate whether the Correctable Error Report is enabled.
**/
UINT8 PcieRpCorrectableErrorReport[28];
/** Offset 0x081F - PCIE RP System Error On Fatal Error
Indicate whether the System Error on Fatal Error is enabled.
**/
UINT8 PcieRpSystemErrorOnFatalError[28];
/** Offset 0x083B - PCIE RP System Error On Non Fatal Error
Indicate whether the System Error on Non Fatal Error is enabled.
**/
UINT8 PcieRpSystemErrorOnNonFatalError[28];
/** Offset 0x0857 - PCIE RP System Error On Correctable Error
Indicate whether the System Error on Correctable Error is enabled.
**/
UINT8 PcieRpSystemErrorOnCorrectableError[28];
/** Offset 0x0873 - PCIE RP Max Payload
Max Payload Size supported, Default 128B, see enum PCH_PCIE_MAX_PAYLOAD.
**/
UINT8 PcieRpMaxPayload[28];
/** Offset 0x088F - Touch Host Controller Port 0 Assignment
Assign THC Port 0
0x0:ThcAssignmentNone, 0x1:ThcAssignmentThc0
**/
UINT8 ThcPort0Assignment;
/** Offset 0x0890 - Touch Host Controller Port 0 Interrupt Pin Mux
Set THC Port 0 Pin Muxing Value if signal can be enabled on multiple pads. Refer
to GPIO_*_MUXING_THC_SPIx_INTB_* for possible values.
**/
UINT32 ThcPort0InterruptPinMuxing;
/** Offset 0x0894 - Reserved
**/
UINT8 Reserved57;
/** Offset 0x0895 - Touch Host Controller Port 1 Assignment
Assign THC Port 1
0x0:ThcAssignmentNone, 0x1:ThcPort1AssignmentThc0, 0x2:ThcAssignmentThc1
**/
UINT8 ThcPort1Assignment;
/** Offset 0x0896 - Reserved
**/
UINT16 Reserved58;
/** Offset 0x0898 - Touch Host Controller Port 1 Interrupt Pin Mux
Set THC Port 1 Pin Muxing Value if signal can be enabled on multiple pads. Refer
to GPIO_*_MUXING_THC_SPIx_INTB_* for possible values.
**/
UINT32 ThcPort1InterruptPinMuxing;
/** Offset 0x089C - Reserved
**/
UINT8 Reserved59;
/** Offset 0x089D - PCIE RP Pcie Speed
Determines each PCIE Port speed capability. 0: Auto; 1: Gen1; 2: Gen2; 3: Gen3;
4: Gen4 (see: PCIE_SPEED).
**/
UINT8 PcieRpPcieSpeed[28];
/** Offset 0x08B9 - PCIE RP Physical Slot Number
Indicates the slot number for the root port. Default is the value as root port index.
**/
UINT8 PcieRpPhysicalSlotNumber[28];
/** Offset 0x08D5 - PCIE RP Completion Timeout
The root port completion timeout(see: PCIE_COMPLETION_TIMEOUT). Default is PchPcieCompletionTO_Default.
**/
UINT8 PcieRpCompletionTimeout[28];
/** Offset 0x08F1 - PCIE RP Aspm
The ASPM configuration of the root port (see: PCH_PCIE_ASPM_CONTROL). Default is
PchPcieAspmAutoConfig.
**/
UINT8 PcieRpAspm[28];
/** Offset 0x090D - PCIE RP L1 Substates
The L1 Substates configuration of the root port (see: PCH_PCIE_L1SUBSTATES_CONTROL).
Default is PchPcieL1SubstatesL1_1_2.
**/
UINT8 PcieRpL1Substates[28];
/** Offset 0x0929 - Reserved
**/
UINT8 Reserved60[28];
/** Offset 0x0945 - PCIE RP Ltr Enable
Latency Tolerance Reporting Mechanism.
**/
UINT8 PcieRpLtrEnable[28];
/** Offset 0x0961 - PCIE RP Ltr Config Lock
0: Disable; 1: Enable.
**/
UINT8 PcieRpLtrConfigLock[28];
/** Offset 0x097D - PCIe override default settings for EQ
Choose PCIe EQ method
$EN_DIS
**/
UINT8 PcieEqOverrideDefault;
/** Offset 0x097E - PCIe choose EQ method
Choose PCIe EQ method
0: HardwareEq, 1: FixedEq
**/
UINT8 PcieEqMethod;
/** Offset 0x097F - PCIe choose EQ mode
Choose PCIe EQ mode
0: PresetEq, 1: CoefficientEq
**/
UINT8 PcieEqMode;
/** Offset 0x0980 - PCIe EQ local transmitter override
Enable/Disable local transmitter override
$EN_DIS
**/
UINT8 PcieEqLocalTransmitterOverrideEnable;
/** Offset 0x0981 - PCIe number of valid list entries
Select number of presets or coefficients depending on the mode
**/
UINT8 PcieEqPh3NumberOfPresetsOrCoefficients;
/** Offset 0x0982 - PCIe pre-cursor coefficient list
Provide a list of pre-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieEqPh3PreCursorList[10];
/** Offset 0x098C - PCIe post-cursor coefficient list
Provide a list of post-cursor coefficients to be used during phase 3 EQ
**/
UINT8 PcieEqPh3PostCursorList[10];
/** Offset 0x0996 - PCIe preset list
Provide a list of presets to be used during phase 3 EQ
**/
UINT8 PcieEqPh3PresetList[11];
/** Offset 0x09A1 - Reserved
**/
UINT8 Reserved61;
/** Offset 0x09A2 - Reserved
**/
UINT16 Reserved62;
/** Offset 0x09A4 - PCIe EQ phase 1 downstream transmitter port preset
Allows to select the downstream port preset value that will be used during phase
1 of equalization
**/
UINT32 PcieEqPh1DownstreamPortTransmitterPreset;
/** Offset 0x09A8 - PCIe EQ phase 1 upstream tranmitter port preset
Allows to select the upstream port preset value that will be used during phase 1
of equalization
**/
UINT32 PcieEqPh1UpstreamPortTransmitterPreset;
/** Offset 0x09AC - PCIe EQ phase 2 local transmitter override preset
Allows to select the value of the preset used during phase 2 local transmitter override
**/
UINT8 PcieEqPh2LocalTransmitterOverridePreset;
/** Offset 0x09AD - PCIE Enable Peer Memory Write
This member describes whether Peer Memory Writes are enabled on the platform.
$EN_DIS
**/
UINT8 PcieEnablePeerMemoryWrite[28];
/** Offset 0x09C9 - PCIE Compliance Test Mode
Compliance Test Mode shall be enabled when using Compliance Load Board.
$EN_DIS
**/
UINT8 PcieComplianceTestMode;
/** Offset 0x09CA - PCIE Rp Function Swap
DEPRECATED. Allows BIOS to use root port function number swapping when root port
of function 0 is disabled.
$EN_DIS
**/
UINT8 PcieRpFunctionSwap;
/** Offset 0x09CB - Enable/Disable PEG GEN3 Static EQ Phase1 programming
Program Gen3 EQ Phase1 Static Presets. Disabled(0x0): Disable EQ Phase1 Static Presets
Programming, Enabled(0x1)(Default): Enable EQ Phase1 Static Presets Programming
$EN_DIS
**/
UINT8 CpuPcieGen3ProgramStaticEq;
/** Offset 0x09CC - Enable/Disable GEN4 Static EQ Phase1 programming
Program Gen4 EQ Phase1 Static Presets. Disabled(0x0): Disable EQ Phase1 Static Presets
Programming, Enabled(0x1)(Default): Enable EQ Phase1 Static Presets Programming
$EN_DIS
**/
UINT8 CpuPcieGen4ProgramStaticEq;
/** Offset 0x09CD - PCH Pm PME_B0_S5_DIS
When cleared (default), wake events from PME_B0_STS are allowed in S5 if PME_B0_EN = 1.
$EN_DIS
**/
UINT8 PchPmPmeB0S5Dis;
/** Offset 0x09CE - PCIE IMR
Enables Isolated Memory Region for PCIe.
$EN_DIS
**/
UINT8 PcieRpImrEnabled;
/** Offset 0x09CF - PCIE IMR port number
Selects PCIE root port number for IMR feature.
**/
UINT8 PcieRpImrSelection;
/** Offset 0x09D0 - PCH Pm Wol Enable Override
Corresponds to the WOL Enable Override bit in the General PM Configuration B (GEN_PMCON_B) register.
$EN_DIS
**/
UINT8 PchPmWolEnableOverride;
/** Offset 0x09D1 - PCH Pm Pcie Wake From DeepSx
Determine if enable PCIe to wake from deep Sx.
$EN_DIS
**/
UINT8 PchPmPcieWakeFromDeepSx;
/** Offset 0x09D2 - PCH Pm WoW lan Enable
Determine if WLAN wake from Sx, corresponds to the HOST_WLAN_PP_EN bit in the PWRM_CFG3 register.
$EN_DIS
**/
UINT8 PchPmWoWlanEnable;
/** Offset 0x09D3 - PCH Pm WoW lan DeepSx Enable
Determine if WLAN wake from DeepSx, corresponds to the DSX_WLAN_PP_EN bit in the
PWRM_CFG3 register.
$EN_DIS
**/
UINT8 PchPmWoWlanDeepSxEnable;
/** Offset 0x09D4 - PCH Pm Lan Wake From DeepSx
Determine if enable LAN to wake from deep Sx.
$EN_DIS
**/
UINT8 PchPmLanWakeFromDeepSx;
/** Offset 0x09D5 - PCH Pm Deep Sx Pol
Deep Sx Policy.
$EN_DIS
**/
UINT8 PchPmDeepSxPol;
/** Offset 0x09D6 - PCH Pm Slp S3 Min Assert
SLP_S3 Minimum Assertion Width Policy. Default is PchSlpS350ms.
**/
UINT8 PchPmSlpS3MinAssert;
/** Offset 0x09D7 - PCH Pm Slp S4 Min Assert
SLP_S4 Minimum Assertion Width Policy. Default is PchSlpS44s.
**/
UINT8 PchPmSlpS4MinAssert;
/** Offset 0x09D8 - PCH Pm Slp Sus Min Assert
SLP_SUS Minimum Assertion Width Policy. Default is PchSlpSus4s.
**/
UINT8 PchPmSlpSusMinAssert;
/** Offset 0x09D9 - PCH Pm Slp A Min Assert
SLP_A Minimum Assertion Width Policy. Default is PchSlpA2s.
**/
UINT8 PchPmSlpAMinAssert;
/** Offset 0x09DA - USB Overcurrent Override for VISA
This option overrides USB Over Current enablement state that USB OC will be disabled
after enabling this option. Enable when VISA pin is muxed with USB OC
$EN_DIS
**/
UINT8 PchEnableDbcObs;
/** Offset 0x09DB - PCH Pm Slp Strch Sus Up
Enable SLP_X Stretching After SUS Well Power Up.
$EN_DIS
**/
UINT8 PchPmSlpStrchSusUp;
/** Offset 0x09DC - PCH Pm Slp Lan Low Dc
Enable/Disable SLP_LAN# Low on DC Power.
$EN_DIS
**/
UINT8 PchPmSlpLanLowDc;
/** Offset 0x09DD - PCH Pm Pwr Btn Override Period
PCH power button override period. 000b-4s, 001b-6s, 010b-8s, 011b-10s, 100b-12s, 101b-14s.
**/
UINT8 PchPmPwrBtnOverridePeriod;
/** Offset 0x09DE - PCH Pm Disable Dsx Ac Present Pulldown
When Disable, PCH will internal pull down AC_PRESENT in deep SX and during G3 exit.
$EN_DIS
**/
UINT8 PchPmDisableDsxAcPresentPulldown;
/** Offset 0x09DF - PCH Pm Disable Native Power Button
Power button native mode disable.
$EN_DIS
**/
UINT8 PchPmDisableNativePowerButton;
/** Offset 0x09E0 - PCH Pm ME_WAKE_STS
Clear the ME_WAKE_STS bit in the Power and Reset Status (PRSTS) register.
$EN_DIS
**/
UINT8 PchPmMeWakeSts;
/** Offset 0x09E1 - PCH Pm WOL_OVR_WK_STS
Clear the WOL_OVR_WK_STS bit in the Power and Reset Status (PRSTS) register.
$EN_DIS
**/
UINT8 PchPmWolOvrWkSts;
/** Offset 0x09E2 - PCH Pm Reset Power Cycle Duration
Could be customized in the unit of second. Please refer to EDS for all support settings.
0 is default, 1 is 1 second, 2 is 2 seconds, ...
**/
UINT8 PchPmPwrCycDur;
/** Offset 0x09E3 - PCH Pm Pcie Pll Ssc
Specifies the Pcie Pll Spread Spectrum Percentage. The default is 0xFF: AUTO - No
BIOS override.
**/
UINT8 PchPmPciePllSsc;
/** Offset 0x09E4 - PCH Legacy IO Low Latency Enable
Set to enable low latency of legacy IO. <b>0: Disable</b>, 1: Enable
$EN_DIS
**/
UINT8 PchLegacyIoLowLatency;
/** Offset 0x09E5 - PCH Sata Pwr Opt Enable
SATA Power Optimizer on PCH side.
$EN_DIS
**/
UINT8 SataPwrOptEnable;
/** Offset 0x09E6 - PCH Sata eSATA Speed Limit
When enabled, BIOS will configure the PxSCTL.SPD to 2 to limit the eSATA port speed.
$EN_DIS
**/
UINT8 EsataSpeedLimit;
/** Offset 0x09E7 - PCH Sata Speed Limit
Indicates the maximum speed the SATA controller can support 0h: PchSataSpeedDefault.
**/
UINT8 SataSpeedLimit;
/** Offset 0x09E8 - Enable SATA Port HotPlug
Enable SATA Port HotPlug.
**/
UINT8 SataPortsHotPlug[8];
/** Offset 0x09F0 - Enable SATA Port Interlock Sw
Enable SATA Port Interlock Sw.
**/
UINT8 SataPortsInterlockSw[8];
/** Offset 0x09F8 - Enable SATA Port External
Enable SATA Port External.
**/
UINT8 SataPortsExternal[8];
/** Offset 0x0A00 - Enable SATA Port SpinUp
Enable the COMRESET initialization Sequence to the device.
**/
UINT8 SataPortsSpinUp[8];
/** Offset 0x0A08 - Enable SATA Port Solid State Drive
0: HDD; 1: SSD.
**/
UINT8 SataPortsSolidStateDrive[8];
/** Offset 0x0A10 - Enable SATA Port Enable Dito Config
Enable DEVSLP Idle Timeout settings (DmVal, DitoVal).
**/
UINT8 SataPortsEnableDitoConfig[8];
/** Offset 0x0A18 - Enable SATA Port DmVal
DITO multiplier. Default is 15.
**/
UINT8 SataPortsDmVal[8];
/** Offset 0x0A20 - Enable SATA Port DmVal
DEVSLP Idle Timeout (DITO), Default is 625.
**/
UINT16 SataPortsDitoVal[8];
/** Offset 0x0A30 - Enable SATA Port ZpOdd
Support zero power ODD.
**/
UINT8 SataPortsZpOdd[8];
/** Offset 0x0A38 - PCH Sata Rst Raid Alternate Id
Enable RAID Alternate ID.
$EN_DIS
**/
UINT8 SataRstRaidDeviceId;
/** Offset 0x0A39 - PCH Sata Rst Pcie Storage Remap enable
Enable Intel RST for PCIe Storage remapping.
**/
UINT8 SataRstPcieEnable[3];
/** Offset 0x0A3C - PCH Sata Rst Pcie Storage Port
Intel RST for PCIe Storage remapping - PCIe Port Selection (1-based, 0 = autodetect).
**/
UINT8 SataRstPcieStoragePort[3];
/** Offset 0x0A3F - PCH Sata Rst Pcie Device Reset Delay
PCIe Storage Device Reset Delay in milliseconds. Default value is 100ms
**/
UINT8 SataRstPcieDeviceResetDelay[3];
/** Offset 0x0A42 - UFS enable/disable
PCIe Storage Device Reset Delay in milliseconds. Default value is 100ms
$EN_DIS
**/
UINT8 UfsEnable[2];
/** Offset 0x0A44 - IEH Mode
Integrated Error Handler Mode, 0: Bypass, 1: Enable
0: Bypass, 1:Enable
**/
UINT8 IehMode;
/** Offset 0x0A45 - Reserved
**/
UINT8 Reserved63;
/** Offset 0x0A46 - Thermal Throttling Custimized T0Level Value
Custimized T0Level value.
**/
UINT16 PchT0Level;
/** Offset 0x0A48 - Thermal Throttling Custimized T1Level Value
Custimized T1Level value.
**/
UINT16 PchT1Level;
/** Offset 0x0A4A - Thermal Throttling Custimized T2Level Value
Custimized T2Level value.
**/
UINT16 PchT2Level;
/** Offset 0x0A4C - Enable The Thermal Throttle
Enable the thermal throttle function.
$EN_DIS
**/
UINT8 PchTTEnable;
/** Offset 0x0A4D - PMSync State 13
When set to 1 and the programmed GPIO pin is a 1, then PMSync state 13 will force
at least T2 state.
$EN_DIS
**/
UINT8 PchTTState13Enable;
/** Offset 0x0A4E - Thermal Throttle Lock
Thermal Throttle Lock.
$EN_DIS
**/
UINT8 PchTTLock;
/** Offset 0x0A4F - Thermal Throttling Suggested Setting
Thermal Throttling Suggested Setting.
$EN_DIS
**/
UINT8 TTSuggestedSetting;
/** Offset 0x0A50 - Enable PCH Cross Throttling
Enable/Disable PCH Cross Throttling
$EN_DIS
**/
UINT8 TTCrossThrottling;
/** Offset 0x0A51 - DMI Thermal Sensor Autonomous Width Enable
DMI Thermal Sensor Autonomous Width Enable.
$EN_DIS
**/
UINT8 PchDmiTsawEn;
/** Offset 0x0A52 - DMI Thermal Sensor Suggested Setting
DMT thermal sensor suggested representative values.
$EN_DIS
**/
UINT8 DmiSuggestedSetting;
/** Offset 0x0A53 - Thermal Sensor 0 Target Width
Thermal Sensor 0 Target Width.
0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
UINT8 DmiTS0TW;
/** Offset 0x0A54 - Thermal Sensor 1 Target Width
Thermal Sensor 1 Target Width.
0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
UINT8 DmiTS1TW;
/** Offset 0x0A55 - Thermal Sensor 2 Target Width
Thermal Sensor 2 Target Width.
0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
UINT8 DmiTS2TW;
/** Offset 0x0A56 - Thermal Sensor 3 Target Width
Thermal Sensor 3 Target Width.
0:x1, 1:x2, 2:x4, 3:x8, 4:x16
**/
UINT8 DmiTS3TW;
/** Offset 0x0A57 - Port 0 T1 Multipler
Port 0 T1 Multipler.
**/
UINT8 SataP0T1M;
/** Offset 0x0A58 - Port 0 T2 Multipler
Port 0 T2 Multipler.
**/
UINT8 SataP0T2M;
/** Offset 0x0A59 - Port 0 T3 Multipler
Port 0 T3 Multipler.
**/
UINT8 SataP0T3M;
/** Offset 0x0A5A - Port 0 Tdispatch
Port 0 Tdispatch.
**/
UINT8 SataP0TDisp;
/** Offset 0x0A5B - Port 1 T1 Multipler
Port 1 T1 Multipler.
**/
UINT8 SataP1T1M;
/** Offset 0x0A5C - Port 1 T2 Multipler
Port 1 T2 Multipler.
**/
UINT8 SataP1T2M;
/** Offset 0x0A5D - Port 1 T3 Multipler
Port 1 T3 Multipler.
**/
UINT8 SataP1T3M;
/** Offset 0x0A5E - Port 1 Tdispatch
Port 1 Tdispatch.
**/
UINT8 SataP1TDisp;
/** Offset 0x0A5F - Port 0 Tinactive
Port 0 Tinactive.
**/
UINT8 SataP0Tinact;
/** Offset 0x0A60 - Port 0 Alternate Fast Init Tdispatch
Port 0 Alternate Fast Init Tdispatch.
$EN_DIS
**/
UINT8 SataP0TDispFinit;
/** Offset 0x0A61 - Port 1 Tinactive
Port 1 Tinactive.
**/
UINT8 SataP1Tinact;
/** Offset 0x0A62 - Port 1 Alternate Fast Init Tdispatch
Port 1 Alternate Fast Init Tdispatch.
$EN_DIS
**/
UINT8 SataP1TDispFinit;
/** Offset 0x0A63 - Sata Thermal Throttling Suggested Setting
Sata Thermal Throttling Suggested Setting.
$EN_DIS
**/
UINT8 SataThermalSuggestedSetting;
/** Offset 0x0A64 - Enable Memory Thermal Throttling
Enable Memory Thermal Throttling.
$EN_DIS
**/
UINT8 PchMemoryThrottlingEnable;
/** Offset 0x0A65 - Memory Thermal Throttling
Enable Memory Thermal Throttling.
**/
UINT8 PchMemoryPmsyncEnable[2];
/** Offset 0x0A67 - Enable Memory Thermal Throttling
Enable Memory Thermal Throttling.
**/
UINT8 PchMemoryC0TransmitEnable[2];
/** Offset 0x0A69 - Enable Memory Thermal Throttling
Enable Memory Thermal Throttling.
**/
UINT8 PchMemoryPinSelection[2];
/** Offset 0x0A6B - Reserved
**/
UINT8 Reserved64;
/** Offset 0x0A6C - Thermal Device Temperature
Decides the temperature.
**/
UINT16 PchTemperatureHotLevel;
/** Offset 0x0A6E - USB2 Port Over Current Pin
Describe the specific over current pin number of USB 2.0 Port N.
**/
UINT8 Usb2OverCurrentPin[16];
/** Offset 0x0A7E - USB3 Port Over Current Pin
Describe the specific over current pin number of USB 3.0 Port N.
**/
UINT8 Usb3OverCurrentPin[10];
/** Offset 0x0A88 - Enable xHCI LTR override
Enables override of recommended LTR values for xHCI
$EN_DIS
**/
UINT8 PchUsbLtrOverrideEnable;
/** Offset 0x0A89 - Reserved
**/
UINT8 Reserved65[2];
/** Offset 0x0A8B - Reserved
**/
UINT8 Reserved66;
/** Offset 0x0A8C - xHCI High Idle Time LTR override
Value used for overriding LTR recommendation for xHCI High Idle Time LTR setting
**/
UINT32 PchUsbLtrHighIdleTimeOverride;
/** Offset 0x0A90 - xHCI Medium Idle Time LTR override
Value used for overriding LTR recommendation for xHCI Medium Idle Time LTR setting
**/
UINT32 PchUsbLtrMediumIdleTimeOverride;
/** Offset 0x0A94 - xHCI Low Idle Time LTR override
Value used for overriding LTR recommendation for xHCI Low Idle Time LTR setting
**/
UINT32 PchUsbLtrLowIdleTimeOverride;
/** Offset 0x0A98 - Enable 8254 Static Clock Gating
Set 8254CGE=1 is required for SLP_S0 support. However, set 8254CGE=1 in POST time
might fail to boot legacy OS using 8254 timer. Make sure it is disabled to support
legacy OS using 8254 timer. Also enable this while S0ix is enabled.
$EN_DIS
**/
UINT8 Enable8254ClockGating;
/** Offset 0x0A99 - Enable 8254 Static Clock Gating On S3
This is only applicable when Enable8254ClockGating is disabled. FSP will do the
8254 CGE programming on S3 resume when Enable8254ClockGatingOnS3 is enabled. This
avoids the SMI requirement for the programming.
$EN_DIS
**/
UINT8 Enable8254ClockGatingOnS3;
/** Offset 0x0A9A - Enable TCO timer.
When FALSE, it disables PCH ACPI timer, and stops TCO timer. NOTE: This will have
huge power impact when it's enabled. If TCO timer is disabled, uCode ACPI timer
emulation must be enabled, and WDAT table must not be exposed to the OS.
$EN_DIS
**/
UINT8 EnableTcoTimer;
/** Offset 0x0A9B - Hybrid Storage Detection and Configuration Mode
Enables support for Hybrid storage devices. 0: Disabled; 1: Dynamic Configuration.
Default is 0: Disabled
0: Disabled, 1: Dynamic Configuration
**/
UINT8 HybridStorageMode;
/** Offset 0x0A9C - Reserved
**/
UINT8 Reserved67;
/** Offset 0x0A9D - Reserved
**/
UINT8 Reserved68;
/** Offset 0x0A9E - Reserved
**/
UINT8 Reserved69;
/** Offset 0x0A9F - Reserved
**/
UINT8 Reserved70[1];
/** Offset 0x0AA0 - BgpdtHash[4]
BgpdtHash values
**/
UINT64 BgpdtHash[4];
/** Offset 0x0AC0 - BiosGuardAttr
BiosGuardAttr default values
**/
UINT32 BiosGuardAttr;
/** Offset 0x0AC4 - Reserved
**/
UINT8 Reserved71[4];
/** Offset 0x0AC8 - BiosGuardModulePtr
BiosGuardModulePtr default values
**/
UINT64 BiosGuardModulePtr;
/** Offset 0x0AD0 - SendEcCmd
SendEcCmd function pointer. \n
@code typedef EFI_STATUS (EFIAPI *PLATFORM_SEND_EC_COMMAND) (IN EC_COMMAND_TYPE
EcCmdType, IN UINT8 EcCmd, IN UINT8 SendData, IN OUT UINT8 *ReceiveData); @endcode
**/
UINT64 SendEcCmd;
/** Offset 0x0AD8 - EcCmdProvisionEav
Ephemeral Authorization Value default values. Provisions an ephemeral shared secret to the EC
**/
UINT8 EcCmdProvisionEav;
/** Offset 0x0AD9 - EcCmdLock
EcCmdLock default values. Locks Ephemeral Authorization Value sent previously
**/
UINT8 EcCmdLock;
/** Offset 0x0ADA - Skip Ssid Programming.
When set to TRUE, silicon code will not do any SSID programming and platform code
needs to handle that by itself properly.
$EN_DIS
**/
UINT8 SiSkipSsidProgramming;
/** Offset 0x0ADB - Reserved
**/
UINT8 Reserved72;
/** Offset 0x0ADC - Change Default SVID
Change the default SVID used in FSP to programming internal devices. This is only
valid when SkipSsidProgramming is FALSE.
**/
UINT16 SiCustomizedSvid;
/** Offset 0x0ADE - Change Default SSID
Change the default SSID used in FSP to programming internal devices. This is only
valid when SkipSsidProgramming is FALSE.
**/
UINT16 SiCustomizedSsid;
/** Offset 0x0AE0 - SVID SDID table Poniter.
The address of the table of SVID SDID to customize each SVID SDID entry. This is
only valid when SkipSsidProgramming is FALSE.
**/
UINT32 SiSsidTablePtr;
/** Offset 0x0AE4 - Number of ssid table.
SiNumberOfSsidTableEntry should match the table entries created in SiSsidTablePtr.
This is only valid when SkipSsidProgramming is FALSE.
**/
UINT16 SiNumberOfSsidTableEntry;
/** Offset 0x0AE6 - USB2 Port Reset Message Enable
0: Disable USB2 Port Reset Message; 1: Enable USB2 Port Reset Message; This must
be enable for USB2 Port those are paired with CPU XHCI Port
**/
UINT8 PortResetMessageEnable[16];
/** Offset 0x0AF6 - SATA RST Interrupt Mode
Allowes to choose which interrupts will be implemented by SATA controller in RAID mode.
0:Msix, 1:Msi, 2:Legacy
**/
UINT8 SataRstInterrupt;
/** Offset 0x0AF7 - ME Unconfig on RTC clear
0: Disable ME Unconfig On Rtc Clear. <b>1: Enable ME Unconfig On Rtc Clear</b>.
2: Cmos is clear, status unkonwn. 3: Reserved
0: Disable ME Unconfig On Rtc Clear, 1: Enable ME Unconfig On Rtc Clear, 2: Cmos
is clear, 3: Reserved
**/
UINT8 MeUnconfigOnRtcClear;
/** Offset 0x0AF8 - Enforce Enhanced Debug Mode
Determine if ME should enter Enhanced Debug Mode. <b>0: disable</b>, 1: enable
$EN_DIS
**/
UINT8 EnforceEDebugMode;
/** Offset 0x0AF9 - Enable PS_ON.
PS_ON is a new C10 state from the CPU on desktop SKUs that enables a lower power
target that will be required by the California Energy Commission (CEC). When FALSE,
PS_ON is to be disabled.
$EN_DIS
**/
UINT8 PsOnEnable;
/** Offset 0x0AFA - Pmc Cpu C10 Gate Pin Enable
Enable/Disable platform support for CPU_C10_GATE# pin to control gating of CPU VccIO
and VccSTG rails instead of SLP_S0# pin.
$EN_DIS
**/
UINT8 PmcCpuC10GatePinEnable;
/** Offset 0x0AFB - Pch Dmi Aspm Ctrl
ASPM configuration on the PCH side of the DMI/OPI Link. Default is <b>PchPcieAspmL1</b>
0:Disabled, 1:L0s, 2:L1, 3:L0sL1, 4:Auto
**/
UINT8 PchDmiAspmCtrl;
/** Offset 0x0AFC - PchDmiCwbEnable
Central Write Buffer feature configurable and enabled by default
$EN_DIS
**/
UINT8 PchDmiCwbEnable;
/** Offset 0x0AFD - OS IDLE Mode Enable
Enable/Disable OS Idle Mode
$EN_DIS
**/
UINT8 PmcOsIdleEnable;
/** Offset 0x0AFE - S0ix Auto-Demotion
Enable/Disable the Low Power Mode Auto-Demotion Host Control feature.
$EN_DIS
**/
UINT8 PchS0ixAutoDemotion;
/** Offset 0x0AFF - Latch Events C10 Exit
When this bit is set to 1, SLP_S0# entry events in SLP_S0_DEBUG_REGx registers are
captured on C10 exit (instead of C10 entry which is default)
$EN_DIS
**/
UINT8 PchPmLatchEventsC10Exit;
/** Offset 0x0B00 - Reserved
**/
UINT8 Reserved73;
/** Offset 0x0B01 - Reserved
**/
UINT8 Reserved74;
/** Offset 0x0B02 - Reserved
**/
UINT8 Reserved75;
/** Offset 0x0B03 - Reserved
**/
UINT8 Reserved76;
/** Offset 0x0B04 - Reserved
**/
UINT8 Reserved77;
/** Offset 0x0B05 - Reserved
**/
UINT8 Reserved78;
/** Offset 0x0B06 - Reserved
**/
UINT8 Reserved79[2];
/** Offset 0x0B08 - Reserved
**/
UINT32 Reserved80;
/** Offset 0x0B0C - PCIE Eq Ph3 Lane Param Cm
CPU_PCIE_EQ_LANE_PARAM. Coefficient C-1.
**/
UINT8 CpuPcieEqPh3LaneParamCm[32];
/** Offset 0x0B2C - PCIE Eq Ph3 Lane Param Cp
CPU_PCIE_EQ_LANE_PARAM. Coefficient C+1.
**/
UINT8 CpuPcieEqPh3LaneParamCp[32];
/** Offset 0x0B4C - Gen3 Root port preset values per lane
Used for programming Pcie Gen3 preset values per lane. Range: 0-9, 8 is default
for each lane
**/
UINT8 CpuPcieGen3RootPortPreset[20];
/** Offset 0x0B60 - Pcie Gen4 Root port preset values per lane
Used for programming Pcie Gen4 preset values per lane. Range: 0-9, 8 is default
for each lane
**/
UINT8 CpuPcieGen4RootPortPreset[20];
/** Offset 0x0B74 - Pcie Gen3 End port preset values per lane
Used for programming Pcie Gen3 preset values per lane. Range: 0-9, 7 is default
for each lane
**/
UINT8 CpuPcieGen3EndPointPreset[20];
/** Offset 0x0B88 - Pcie Gen4 End port preset values per lane
Used for programming Pcie Gen4 preset values per lane. Range: 0-9, 7 is default
for each lane
**/
UINT8 CpuPcieGen4EndPointPreset[20];
/** Offset 0x0B9C - Pcie Gen3 End port Hint values per lane
Used for programming Pcie Gen3 Hint values per lane. Range: 0-6, 2 is default for each lane
**/
UINT8 CpuPcieGen3EndPointHint[20];
/** Offset 0x0BB0 - Pcie Gen4 End port Hint values per lane
Used for programming Pcie Gen4 Hint values per lane. Range: 0-6, 2 is default for each lane
**/
UINT8 CpuPcieGen4EndPointHint[20];
/** Offset 0x0BC4 - CPU PCIe Fia Programming
Load Fia configuration if enable. 0: Disable; 1: Enable(Default).
$EN_DIS
**/
UINT8 CpuPcieFiaProgramming;
/** Offset 0x0BC5 - CPU PCIe RootPort Clock Gating
Describes whether the PCI Express Clock Gating for each root port is enabled by
platform modules. 0: Disable; 1: Enable(Default).
$EN_DIS
**/
UINT8 CpuPcieClockGating[4];
/** Offset 0x0BC9 - CPU PCIe RootPort Power Gating
Describes whether the PCI Express Power Gating for each root port is enabled by
platform modules. 0: Disable; 1: Enable(Default).
$EN_DIS
**/
UINT8 CpuPciePowerGating[4];
/** Offset 0x0BCD - PCIE Compliance Test Mode
Compliance Test Mode shall be enabled when using Compliance Load Board.
$EN_DIS
**/
UINT8 CpuPcieComplianceTestMode;
/** Offset 0x0BCE - PCIE Enable Peer Memory Write
This member describes whether Peer Memory Writes are enabled on the platform.
$EN_DIS
**/
UINT8 CpuPcieEnablePeerMemoryWrite;
/** Offset 0x0BCF - PCIE Rp Function Swap
Allows BIOS to use root port function number swapping when root port of function
0 is disabled.
$EN_DIS
**/
UINT8 CpuPcieRpFunctionSwap;
/** Offset 0x0BD0 - PCI Express Slot Selection
Select the PCIe M2 or CEMx4 slot.0: CEMx4 slot; 1: M2 slot(Default).
$EN_DIS
**/
UINT8 CpuPcieSlotSelection;
/** Offset 0x0BD1 - Reserved
**/
UINT8 Reserved81[3];
/** Offset 0x0BD4 - CPU PCIE device override table pointer
The PCIe device table is being used to override PCIe device ASPM settings. This
is a pointer points to a 32bit address. And it's only used in PostMem phase. Please
refer to CPU_PCIE_DEVICE_OVERRIDE structure for the table. Last entry VendorId
must be 0.
**/
UINT32 CpuPcieDeviceOverrideTablePtr;
/** Offset 0x0BD8 - Enable PCIE RP HotPlug
Indicate whether the root port is hot plug available.
**/
UINT8 CpuPcieRpHotPlug[4];
/** Offset 0x0BDC - Enable PCIE RP Pm Sci
Indicate whether the root port power manager SCI is enabled.
**/
UINT8 CpuPcieRpPmSci[4];
/** Offset 0x0BE0 - Enable PCIE RP Transmitter Half Swing
Indicate whether the Transmitter Half Swing is enabled.
**/
UINT8 CpuPcieRpTransmitterHalfSwing[4];
/** Offset 0x0BE4 - PCIE RP Access Control Services Extended Capability
Enable/Disable PCIE RP Access Control Services Extended Capability
**/
UINT8 CpuPcieRpAcsEnabled[4];
/** Offset 0x0BE8 - PCIE RP Clock Power Management
Enable/Disable PCIE RP Clock Power Management, even if disabled, CLKREQ# signal
can still be controlled by L1 PM substates mechanism
**/
UINT8 CpuPcieRpEnableCpm[4];
/** Offset 0x0BEC - PCIE RP Advanced Error Report
Indicate whether the Advanced Error Reporting is enabled.
**/
UINT8 CpuPcieRpAdvancedErrorReporting[4];
/** Offset 0x0BF0 - PCIE RP Unsupported Request Report
Indicate whether the Unsupported Request Report is enabled.
**/
UINT8 CpuPcieRpUnsupportedRequestReport[4];
/** Offset 0x0BF4 - PCIE RP Fatal Error Report
Indicate whether the Fatal Error Report is enabled.
**/
UINT8 CpuPcieRpFatalErrorReport[4];
/** Offset 0x0BF8 - PCIE RP No Fatal Error Report
Indicate whether the No Fatal Error Report is enabled.
**/
UINT8 CpuPcieRpNoFatalErrorReport[4];
/** Offset 0x0BFC - PCIE RP Correctable Error Report
Indicate whether the Correctable Error Report is enabled.
**/
UINT8 CpuPcieRpCorrectableErrorReport[4];
/** Offset 0x0C00 - PCIE RP System Error On Fatal Error
Indicate whether the System Error on Fatal Error is enabled.
**/
UINT8 CpuPcieRpSystemErrorOnFatalError[4];
/** Offset 0x0C04 - PCIE RP System Error On Non Fatal Error
Indicate whether the System Error on Non Fatal Error is enabled.
**/
UINT8 CpuPcieRpSystemErrorOnNonFatalError[4];
/** Offset 0x0C08 - PCIE RP System Error On Correctable Error
Indicate whether the System Error on Correctable Error is enabled.
**/
UINT8 CpuPcieRpSystemErrorOnCorrectableError[4];
/** Offset 0x0C0C - PCIE RP Max Payload
Max Payload Size supported, Default 128B, see enum CPU_PCIE_MAX_PAYLOAD.
**/
UINT8 CpuPcieRpMaxPayload[4];
/** Offset 0x0C10 - DPC for PCIE RP Mask
Enable/disable Downstream Port Containment for PCIE Root Ports. 0: disable, 1: enable.
One bit for each port, bit0 for port1, bit1 for port2, and so on.
**/
UINT8 CpuPcieRpDpcEnabled[4];
/** Offset 0x0C14 - DPC Extensions PCIE RP Mask
Enable/disable DPC Extensions for PCIE Root Ports. 0: disable, 1: enable. One bit
for each port, bit0 for port1, bit1 for port2, and so on.
**/
UINT8 CpuPcieRpDpcExtensionsEnabled[4];
/** Offset 0x0C18 - CPU PCIe root port connection type
0: built-in device, 1:slot
**/
UINT8 CpuPcieRpSlotImplemented[4];
/** Offset 0x0C1C - PCIE RP Gen3 Equalization Phase Method
PCIe Gen3 Eq Ph3 Method (see CPU_PCIE_EQ_METHOD). 0: DEPRECATED, hardware equalization;
1: hardware equalization; 4: Fixed Coeficients.
**/
UINT8 CpuPcieRpGen3EqPh3Method[4];
/** Offset 0x0C20 - PCIE RP Gen4 Equalization Phase Method
PCIe Gen4 Eq Ph3 Method (see CPU_PCIE_EQ_METHOD). 0: DEPRECATED, hardware equalization;
1: hardware equalization; 4: Fixed Coeficients.
**/
UINT8 CpuPcieRpGen4EqPh3Method[4];
/** Offset 0x0C24 - PCIE RP Physical Slot Number
Indicates the slot number for the root port. Default is the value as root port index.
**/
UINT8 CpuPcieRpPhysicalSlotNumber[4];
/** Offset 0x0C28 - PCIE RP Aspm
The ASPM configuration of the root port (see: CPU_PCIE_ASPM_CONTROL).0: Disable;
1: CpuPcieAspmL0s; 2: CpuPcieAspmL1; 3:CpuPcieAspmL0sL1(Default)
**/
UINT8 CpuPcieRpAspm[4];
/** Offset 0x0C2C - PCIE RP L1 Substates
The L1 Substates configuration of the root port (see: CPU_PCIE_L1SUBSTATES_CONTROL).
Default is CpuPcieL1SubstatesL1_1_2.
**/
UINT8 CpuPcieRpL1Substates[4];
/** Offset 0x0C30 - PCIE RP Ltr Enable
Latency Tolerance Reporting Mechanism.
**/
UINT8 CpuPcieRpLtrEnable[4];
/** Offset 0x0C34 - PCIE RP Ltr Config Lock
0: Disable; 1: Enable.
**/
UINT8 CpuPcieRpLtrConfigLock[4];
/** Offset 0x0C38 - PTM for PCIE RP Mask
Enable/disable Precision Time Measurement for PCIE Root Ports. 0: disable, 1: enable.
One bit for each port, bit0 for port1, bit1 for port2, and so on.
**/
UINT8 CpuPcieRpPtmEnabled[4];
/** Offset 0x0C3C - PCIE RP Detect Timeout Ms
The number of milliseconds within 0~65535 in reference code will wait for link to
exit Detect state for enabled ports before assuming there is no device and potentially
disabling the port.
**/
UINT16 CpuPcieRpDetectTimeoutMs[4];
/** Offset 0x0C44 - Multi-VC for PCIE RP Mask
Enable/disable Multiple Virtual Channel for PCIE Root Ports. 0: disable, 1: enable.
One bit for each port, bit0 for port1, bit1 for port2, and so on.
**/
UINT8 CpuPcieRpMultiVcEnabled[4];
/** Offset 0x0C48 - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 3
Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 3, Each
value in array can be between 0-1. One byte for each port.
**/
UINT8 Usb3HsioTxRate3UniqTranEnable[10];
/** Offset 0x0C52 - USB 3.0 TX Output Unique Transition Bit Scale for rate 3
USB 3.0 TX Output Unique Transition Bit Scale for rate 3, HSIO_TX_DWORD9[6:0], <b>Default
= 4Ch</b>. One byte for each port.
**/
UINT8 Usb3HsioTxRate3UniqTran[10];
/** Offset 0x0C5C - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 2
Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 2, Each
value in array can be between 0-1. One byte for each port.
**/
UINT8 Usb3HsioTxRate2UniqTranEnable[10];
/** Offset 0x0C66 - USB 3.0 TX Output Unique Transition Bit Scale for rate 2
USB 3.0 TX Output Unique Transition Bit Scale for rate 2, HSIO_TX_DWORD9[14:8],
<b>Default = 4Ch</b>. One byte for each port.
**/
UINT8 Usb3HsioTxRate2UniqTran[10];
/** Offset 0x0C70 - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 1
Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 1, Each
value in array can be between 0-1. One byte for each port.
**/
UINT8 Usb3HsioTxRate1UniqTranEnable[10];
/** Offset 0x0C7A - USB 3.0 TX Output Unique Transition Bit Scale for rate 1
USB 3.0 TX Output Unique Transition Bit Scale for rate 1, HSIO_TX_DWORD9[22:16],
<b>Default = 4Ch</b>. One byte for each port.
**/
UINT8 Usb3HsioTxRate1UniqTran[10];
/** Offset 0x0C84 - Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 0
Enable the write to USB 3.0 TX Output Unique Transition Bit Mode for rate 0, Each
value in array can be between 0-1. One byte for each port.
**/
UINT8 Usb3HsioTxRate0UniqTranEnable[10];
/** Offset 0x0C8E - USB 3.0 TX Output Unique Transition Bit Scale for rate 0
USB 3.0 TX Output Unique Transition Bit Scale for rate 0, HSIO_TX_DWORD9[30:24],
<b>Default = 4Ch</b>. One byte for each port.
**/
UINT8 Usb3HsioTxRate0UniqTran[10];
/** Offset 0x0C98 - Skip PAM regsiter lock
Enable: PAM register will not be locked by RC, platform code should lock it, Disable(Default):
PAM registers will be locked by RC
$EN_DIS
**/
UINT8 SkipPamLock;
/** Offset 0x0C99 - EDRAM Test Mode
Enable: PAM register will not be locked by RC, platform code should lock it, Disable(Default):
PAM registers will be locked by RC
0: EDRAM SW disable, 1: EDRAM SW Enable, 2: EDRAM HW mode
**/
UINT8 EdramTestMode;
/** Offset 0x0C9A - Enable/Disable IGFX RenderStandby
Enable(Default): Enable IGFX RenderStandby, Disable: Disable IGFX RenderStandby
$EN_DIS
**/
UINT8 RenderStandby;
/** Offset 0x0C9B - Enable/Disable IGFX PmSupport
Enable(Default): Enable IGFX PmSupport, Disable: Disable IGFX PmSupport
$EN_DIS
**/
UINT8 PmSupport;
/** Offset 0x0C9C - Enable/Disable CdynmaxClamp
Enable: Enable CdynmaxClamp, Disable(Default): Disable CdynmaxClamp
$EN_DIS
**/
UINT8 CdynmaxClampEnable;
/** Offset 0x0C9D - GT Frequency Limit
0xFF: Auto(Default), 2: 100 Mhz, 3: 150 Mhz, 4: 200 Mhz, 5: 250 Mhz, 6: 300 Mhz,
7: 350 Mhz, 8: 400 Mhz, 9: 450 Mhz, 0xA: 500 Mhz, 0xB: 550 Mhz, 0xC: 600 Mhz, 0xD:
650 Mhz, 0xE: 700 Mhz, 0xF: 750 Mhz, 0x10: 800 Mhz, 0x11: 850 Mhz, 0x12:900 Mhz,
0x13: 950 Mhz, 0x14: 1000 Mhz, 0x15: 1050 Mhz, 0x16: 1100 Mhz, 0x17: 1150 Mhz,
0x18: 1200 Mhz
0xFF: Auto(Default), 2: 100 Mhz, 3: 150 Mhz, 4: 200 Mhz, 5: 250 Mhz, 6: 300 Mhz,
7: 350 Mhz, 8: 400 Mhz, 9: 450 Mhz, 0xA: 500 Mhz, 0xB: 550 Mhz, 0xC: 600 Mhz, 0xD:
650 Mhz, 0xE: 700 Mhz, 0xF: 750 Mhz, 0x10: 800 Mhz, 0x11: 850 Mhz, 0x12:900 Mhz,
0x13: 950 Mhz, 0x14: 1000 Mhz, 0x15: 1050 Mhz, 0x16: 1100 Mhz, 0x17: 1150 Mhz,
0x18: 1200 Mhz
**/
UINT8 GtFreqMax;
/** Offset 0x0C9E - Disable Turbo GT
0=Disable: GT frequency is not limited, 1=Enable: Disables Turbo GT frequency
$EN_DIS
**/
UINT8 DisableTurboGt;
/** Offset 0x0C9F - Enable/Disable CdClock Init
Enable: Skip Full CD clock initializaton, Disable(Default): Initialize the full
CD clock if not initialized by Gfx PEIM
$EN_DIS
**/
UINT8 SkipCdClockInit;
/** Offset 0x0CA0 - Enable RC1p frequency request to PMA (provided all other conditions are met)
0(Default)=Disable, 1=Enable
$EN_DIS
**/
UINT8 RC1pFreqEnable;
/** Offset 0x0CA1 - Enable TSN Multi-VC
Enable/disable Multi Virtual Channels(VC) in TSN.
$EN_DIS
**/
UINT8 PchTsnMultiVcEnable;
/** Offset 0x0CA2 - Reserved
**/
UINT8 Reserved82[2];
/** Offset 0x0CA4 - LogoPixelHeight Address
Address of LogoPixelHeight
**/
UINT32 LogoPixelHeight;
/** Offset 0x0CA8 - LogoPixelWidth Address
Address of LogoPixelWidth
**/
UINT32 LogoPixelWidth;
/** Offset 0x0CAC - Reserved
**/
UINT8 Reserved83;
/** Offset 0x0CAD - Reserved
**/
UINT8 Reserved84;
/** Offset 0x0CAE - Reserved
**/
UINT8 Reserved85[3];
/** Offset 0x0CB1 - RSR feature
Enable or Disable RSR feature; 0: Disable; <b>1: Enable </b>
$EN_DIS
**/
UINT8 EnableRsr;
/** Offset 0x0CB2 - Reserved
**/
UINT8 Reserved86[4];
/** Offset 0x0CB6 - Enable or Disable HWP
Enable or Disable HWP(Hardware P states) Support. 0: Disable; <b>1: Enable;</b>
2-3:Reserved
$EN_DIS
**/
UINT8 Hwp;
/** Offset 0x0CB7 - Hardware Duty Cycle Control
Hardware Duty Cycle Control configuration. 0: Disabled; <b>1: Enabled</b> 2-3:Reserved
$EN_DIS
**/
UINT8 HdcControl;
/** Offset 0x0CB8 - Package Long duration turbo mode time
Package Long duration turbo mode time window in seconds. Valid values(Unit in seconds)
0 to 8 , 10 , 12 ,14 , 16 , 20 , 24 , 28 , 32 , 40 , 48 , 56 , 64 , 80 , 96 , 112 , 128
**/
UINT8 PowerLimit1Time;
/** Offset 0x0CB9 - Short Duration Turbo Mode
Enable or Disable short duration Turbo Mode. </b>0 : Disable; <b>1: Enable</b>
$EN_DIS
**/
UINT8 PowerLimit2;
/** Offset 0x0CBA - Turbo settings Lock
Lock all Turbo settings Enable/Disable; <b>0: Disable , </b> 1: Enable
$EN_DIS
**/
UINT8 TurboPowerLimitLock;
/** Offset 0x0CBB - Package PL3 time window
Package PL3 time window range for this policy from 0 to 64ms
**/
UINT8 PowerLimit3Time;
/** Offset 0x0CBC - Package PL3 Duty Cycle
Package PL3 Duty Cycle; Valid Range is 0 to 100
**/
UINT8 PowerLimit3DutyCycle;
/** Offset 0x0CBD - Package PL3 Lock
Package PL3 Lock Enable/Disable; <b>0: Disable</b> ; 1:Enable
$EN_DIS
**/
UINT8 PowerLimit3Lock;
/** Offset 0x0CBE - Package PL4 Lock
Package PL4 Lock Enable/Disable; <b>0: Disable</b> ; 1:Enable
$EN_DIS
**/
UINT8 PowerLimit4Lock;
/** Offset 0x0CBF - TCC Activation Offset
TCC Activation Offset. Offset from factory set TCC activation temperature at which
the Thermal Control Circuit must be activated. TCC will be activated at TCC Activation
Temperature, in volts.For SKL Y SKU, the recommended default for this policy is
<b>10</b>, For all other SKUs the recommended default are <b>0</b>
**/
UINT8 TccActivationOffset;
/** Offset 0x0CC0 - Tcc Offset Clamp Enable/Disable
Tcc Offset Clamp for Runtime Average Temperature Limit (RATL) allows CPU to throttle
below P1.For SKL Y SKU, the recommended default for this policy is <b>1: Enabled</b>,
For all other SKUs the recommended default are <b>0: Disabled</b>.
$EN_DIS
**/
UINT8 TccOffsetClamp;
/** Offset 0x0CC1 - Tcc Offset Lock
Tcc Offset Lock for Runtime Average Temperature Limit (RATL) to lock temperature
target; <b>0: Disabled</b>; 1: Enabled.
$EN_DIS
**/
UINT8 TccOffsetLock;
/** Offset 0x0CC2 - Custom Ratio State Entries
The number of custom ratio state entries, ranges from 0 to 40 for a valid custom
ratio table.Sets the number of custom P-states. At least 2 states must be present
**/
UINT8 NumberOfEntries;
/** Offset 0x0CC3 - Custom Short term Power Limit time window
Short term Power Limit time window value for custom CTDP level 1. Valid Range 0 to 128
**/
UINT8 Custom1PowerLimit1Time;
/** Offset 0x0CC4 - Custom Turbo Activation Ratio
Turbo Activation Ratio for custom cTDP level 1. Valid Range 0 to 255
**/
UINT8 Custom1TurboActivationRatio;
/** Offset 0x0CC5 - Custom Config Tdp Control
Config Tdp Control (0/1/2) value for custom cTDP level 1. Valid Range is 0 to 2
**/
UINT8 Custom1ConfigTdpControl;
/** Offset 0x0CC6 - Custom Short term Power Limit time window
Short term Power Limit time window value for custom CTDP level 2. Valid Range 0 to 128
**/
UINT8 Custom2PowerLimit1Time;
/** Offset 0x0CC7 - Custom Turbo Activation Ratio
Turbo Activation Ratio for custom cTDP level 2. Valid Range 0 to 255
**/
UINT8 Custom2TurboActivationRatio;
/** Offset 0x0CC8 - Custom Config Tdp Control
Config Tdp Control (0/1/2) value for custom cTDP level 1. Valid Range is 0 to 2
**/
UINT8 Custom2ConfigTdpControl;
/** Offset 0x0CC9 - Custom Short term Power Limit time window
Short term Power Limit time window value for custom CTDP level 3. Valid Range 0 to 128
**/
UINT8 Custom3PowerLimit1Time;
/** Offset 0x0CCA - Custom Turbo Activation Ratio
Turbo Activation Ratio for custom cTDP level 3. Valid Range 0 to 255
**/
UINT8 Custom3TurboActivationRatio;
/** Offset 0x0CCB - Custom Config Tdp Control
Config Tdp Control (0/1/2) value for custom cTDP level 1. Valid Range is 0 to 2
**/
UINT8 Custom3ConfigTdpControl;
/** Offset 0x0CCC - ConfigTdp mode settings Lock
Lock the ConfigTdp mode settings from runtime changes; <b>0: Disable</b>; 1: Enable
$EN_DIS
**/
UINT8 ConfigTdpLock;
/** Offset 0x0CCD - Load Configurable TDP SSDT
Configure whether to load Configurable TDP SSDT; <b>0: Disable</b>; 1: Enable.
$EN_DIS
**/
UINT8 ConfigTdpBios;
/** Offset 0x0CCE - PL1 Enable value
PL1 Enable value to limit average platform power. <b>0: Disable</b>; 1: Enable.
$EN_DIS
**/
UINT8 PsysPowerLimit1;
/** Offset 0x0CCF - PL1 timewindow
PL1 timewindow in seconds.Valid values(Unit in seconds) 0 to 8 , 10 , 12 ,14 , 16
, 20 , 24 , 28 , 32 , 40 , 48 , 56 , 64 , 80 , 96 , 112 , 128
**/
UINT8 PsysPowerLimit1Time;
/** Offset 0x0CD0 - PL2 Enable Value
PL2 Enable activates the PL2 value to limit average platform power.<b>0: Disable</b>;
1: Enable.
$EN_DIS
**/
UINT8 PsysPowerLimit2;
/** Offset 0x0CD1 - Enable or Disable MLC Streamer Prefetcher
Enable or Disable MLC Streamer Prefetcher; 0: Disable; <b>1: Enable</b>.
$EN_DIS
**/
UINT8 MlcStreamerPrefetcher;
/** Offset 0x0CD2 - Enable or Disable MLC Spatial Prefetcher
Enable or Disable MLC Spatial Prefetcher; 0: Disable; <b>1: Enable</b>
$EN_DIS
**/
UINT8 MlcSpatialPrefetcher;
/** Offset 0x0CD3 - Enable or Disable Monitor /MWAIT instructions
Enable or Disable Monitor /MWAIT instructions; 0: Disable; <b>1: Enable</b>.
$EN_DIS
**/
UINT8 MonitorMwaitEnable;
/** Offset 0x0CD4 - Enable or Disable initialization of machine check registers
Enable or Disable initialization of machine check registers; 0: Disable; <b>1: Enable</b>.
$EN_DIS
**/
UINT8 MachineCheckEnable;
/** Offset 0x0CD5 - AP Idle Manner of waiting for SIPI
AP Idle Manner of waiting for SIPI; 1: HALT loop; <b>2: MWAIT loop</b>; 3: RUN loop.
1: HALT loop, 2: MWAIT loop, 3: RUN loop
**/
UINT8 ApIdleManner;
/** Offset 0x0CD6 - Control on Processor Trace output scheme
Control on Processor Trace output scheme; <b>0: Single Range Output</b>; 1: ToPA Output.
0: Single Range Output, 1: ToPA Output
**/
UINT8 ProcessorTraceOutputScheme;
/** Offset 0x0CD7 - Enable or Disable Processor Trace feature
Enable or Disable Processor Trace feature; <b>0: Disable</b>; 1: Enable.
$EN_DIS
**/
UINT8 ProcessorTraceEnable;
/** Offset 0x0CD8 - Enable or Disable Intel SpeedStep Technology
Enable or Disable Intel SpeedStep Technology. 0: Disable; <b>1: Enable</b>
$EN_DIS
**/
UINT8 Eist;
/** Offset 0x0CD9 - Enable or Disable Energy Efficient P-state
Enable or Disable Energy Efficient P-state will be applied in Turbo mode. Disable;
<b>1: Enable</b>
$EN_DIS
**/
UINT8 EnergyEfficientPState;
/** Offset 0x0CDA - Enable or Disable Energy Efficient Turbo
Enable or Disable Energy Efficient Turbo, will be applied in Turbo mode. <b>0: Disable</b>; 1: Enable
$EN_DIS
**/
UINT8 EnergyEfficientTurbo;
/** Offset 0x0CDB - Enable or Disable T states
Enable or Disable T states; <b>0: Disable</b>; 1: Enable.
$EN_DIS
**/
UINT8 TStates;
/** Offset 0x0CDC - Enable or Disable Bi-Directional PROCHOT#
Enable or Disable Bi-Directional PROCHOT#; 0: Disable; <b>1: Enable</b>
$EN_DIS
**/
UINT8 BiProcHot;
/** Offset 0x0CDD - Enable or Disable PROCHOT# signal being driven externally
Enable or Disable PROCHOT# signal being driven externally; 0: Disable; <b>1: Enable</b>.
$EN_DIS
**/
UINT8 DisableProcHotOut;
/** Offset 0x0CDE - Enable or Disable PROCHOT# Response
Enable or Disable PROCHOT# Response; 0: Disable; <b>1: Enable</b>.
$EN_DIS
**/
UINT8 ProcHotResponse;
/** Offset 0x0CDF - Enable or Disable VR Thermal Alert
Enable or Disable VR Thermal Alert; <b>0: Disable</b>; 1: Enable.
$EN_DIS
**/
UINT8 DisableVrThermalAlert;
/** Offset 0x0CE0 - Enable or Disable Thermal Reporting
Enable or Disable Thermal Reporting through ACPI tables; 0: Disable; <b>1: Enable</b>.
$EN_DIS
**/
UINT8 EnableAllThermalFunctions;
/** Offset 0x0CE1 - Enable or Disable Thermal Monitor
Enable or Disable Thermal Monitor; 0: Disable; <b>1: Enable</b>
$EN_DIS
**/
UINT8 ThermalMonitor;
/** Offset 0x0CE2 - Enable or Disable CPU power states (C-states)
Enable or Disable CPU power states (C-states). 0: Disable; <b>1: Enable</b>
$EN_DIS
**/
UINT8 Cx;
/** Offset 0x0CE3 - Configure C-State Configuration Lock
Configure C-State Configuration Lock; 0: Disable; <b>1: Enable</b>.
$EN_DIS
**/
UINT8 PmgCstCfgCtrlLock;
/** Offset 0x0CE4 - Enable or Disable Enhanced C-states
Enable or Disable Enhanced C-states. 0: Disable; <b>1: Enable</b>
$EN_DIS
**/
UINT8 C1e;
/** Offset 0x0CE5 - Enable or Disable Package Cstate Demotion
Enable or Disable Package Cstate Demotion. 0: Disable; <b>1: Enable</b>
$EN_DIS
**/
UINT8 PkgCStateDemotion;
/** Offset 0x0CE6 - Enable or Disable Package Cstate UnDemotion
Enable or Disable Package Cstate UnDemotion. 0: Disable; <b>1: Enable</b>
$EN_DIS
**/
UINT8 PkgCStateUnDemotion;
/** Offset 0x0CE7 - Enable or Disable CState-Pre wake
Enable or Disable CState-Pre wake. 0: Disable; <b>1: Enable</b>
$EN_DIS
**/
UINT8 CStatePreWake;
/** Offset 0x0CE8 - Enable or Disable TimedMwait Support.
Enable or Disable TimedMwait Support. <b>0: Disable</b>; 1: Enable
$EN_DIS
**/
UINT8 TimedMwait;
/** Offset 0x0CE9 - Enable or Disable IO to MWAIT redirection
Enable or Disable IO to MWAIT redirection; <b>0: Disable</b>; 1: Enable.
$EN_DIS
**/
UINT8 CstCfgCtrIoMwaitRedirection;
/** Offset 0x0CEA - Set the Max Pkg Cstate
Set the Max Pkg Cstate. Default set to Auto which limits the Max Pkg Cstate to deep
C-state. Valid values 0 - C0/C1 , 1 - C2 , 2 - C3 , 3 - C6 , 4 - C7 , 5 - C7S ,
6 - C8 , 7 - C9 , 8 - C10 , 254 - CPU Default , 255 - Auto
**/
UINT8 PkgCStateLimit;
/** Offset 0x0CEB - TimeUnit for C-State Latency Control0
TimeUnit for C-State Latency Control0; Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
, 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
UINT8 CstateLatencyControl0TimeUnit;
/** Offset 0x0CEC - TimeUnit for C-State Latency Control1
TimeUnit for C-State Latency Control1;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
, 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
UINT8 CstateLatencyControl1TimeUnit;
/** Offset 0x0CED - TimeUnit for C-State Latency Control2
TimeUnit for C-State Latency Control2;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
, 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
UINT8 CstateLatencyControl2TimeUnit;
/** Offset 0x0CEE - TimeUnit for C-State Latency Control3
TimeUnit for C-State Latency Control3;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
, 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
UINT8 CstateLatencyControl3TimeUnit;
/** Offset 0x0CEF - TimeUnit for C-State Latency Control4
Time - 1ns , 1 - 32ns , 2 - 1024ns , 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
UINT8 CstateLatencyControl4TimeUnit;
/** Offset 0x0CF0 - TimeUnit for C-State Latency Control5
TimeUnit for C-State Latency Control5;Valid values 0 - 1ns , 1 - 32ns , 2 - 1024ns
, 3 - 32768ns , 4 - 1048576ns , 5 - 33554432ns
**/
UINT8 CstateLatencyControl5TimeUnit;
/** Offset 0x0CF1 - Interrupt Redirection Mode Select
Interrupt Redirection Mode Select.0: Fixed priority; 1: Round robin;2: Hash vector;7:
No change.
**/
UINT8 PpmIrmSetting;
/** Offset 0x0CF2 - Lock prochot configuration
Lock prochot configuration Enable/Disable; 0: Disable;<b> 1: Enable</b>
$EN_DIS
**/
UINT8 ProcHotLock;
/** Offset 0x0CF3 - Configuration for boot TDP selection
Deprecated. Move to premem.
**/
UINT8 ConfigTdpLevel;
/** Offset 0x0CF4 - Max P-State Ratio
Max P-State Ratio, Valid Range 0 to 0x7F
**/
UINT8 MaxRatio;
/** Offset 0x0CF5 - P-state ratios for custom P-state table
P-state ratios for custom P-state table. NumberOfEntries has valid range between
0 to 40. For no. of P-States supported(NumberOfEntries) , StateRatio[NumberOfEntries]
are configurable. Valid Range of each entry is 0 to 0x7F
**/
UINT8 StateRatio[40];
/** Offset 0x0D1D - P-state ratios for max 16 version of custom P-state table
P-state ratios for max 16 version of custom P-state table. This table is used for
OS versions limited to a max of 16 P-States. If the first entry of this table is
0, or if Number of Entries is 16 or less, then this table will be ignored, and
up to the top 16 values of the StateRatio table will be used instead. Valid Range
of each entry is 0 to 0x7F
**/
UINT8 StateRatioMax16[16];
/** Offset 0x0D2D - Reserved
**/
UINT8 Reserved87;
/** Offset 0x0D2E - Platform Power Pmax
PCODE MMIO Mailbox: Platform Power Pmax. <b>0 - Auto</b> Specified in 1/8 Watt increments.
Range 0-1024 Watts. Value of 800 = 100W
**/
UINT16 PsysPmax;
/** Offset 0x0D30 - Interrupt Response Time Limit of C-State LatencyContol1
Interrupt Response Time Limit of C-State LatencyContol1.Range of value 0 to 0x3FF.
0 is Auto.
**/
UINT16 CstateLatencyControl1Irtl;
/** Offset 0x0D32 - Interrupt Response Time Limit of C-State LatencyContol2
Interrupt Response Time Limit of C-State LatencyContol2.Range of value 0 to 0x3FF.
0 is Auto.
**/
UINT16 CstateLatencyControl2Irtl;
/** Offset 0x0D34 - Interrupt Response Time Limit of C-State LatencyContol3
Interrupt Response Time Limit of C-State LatencyContol3.Range of value 0 to 0x3FF.
0 is Auto.
**/
UINT16 CstateLatencyControl3Irtl;
/** Offset 0x0D36 - Interrupt Response Time Limit of C-State LatencyContol4
Interrupt Response Time Limit of C-State LatencyContol4.Range of value 0 to 0x3FF.
0 is Auto.
**/
UINT16 CstateLatencyControl4Irtl;
/** Offset 0x0D38 - Interrupt Response Time Limit of C-State LatencyContol5
Interrupt Response Time Limit of C-State LatencyContol5.Range of value 0 to 0x3FF.
0 is Auto.
**/
UINT16 CstateLatencyControl5Irtl;
/** Offset 0x0D3A - Reserved
**/
UINT8 Reserved88[2];
/** Offset 0x0D3C - Package Long duration turbo mode power limit
Package Long duration turbo mode power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.
Valid Range 0 to 4095875 in Step size of 125
**/
UINT32 PowerLimit1;
/** Offset 0x0D40 - Package Short duration turbo mode power limit
Package Short duration turbo mode power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 PowerLimit2Power;
/** Offset 0x0D44 - Package PL3 power limit
Package PL3 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 PowerLimit3;
/** Offset 0x0D48 - Package PL4 power limit
Package PL4 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 PowerLimit4;
/** Offset 0x0D4C - Tcc Offset Time Window for RATL
Package PL4 power limit. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 TccOffsetTimeWindowForRatl;
/** Offset 0x0D50 - Short term Power Limit value for custom cTDP level 1
Short term Power Limit value for custom cTDP level 1. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 Custom1PowerLimit1;
/** Offset 0x0D54 - Long term Power Limit value for custom cTDP level 1
Long term Power Limit value for custom cTDP level 1. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 Custom1PowerLimit2;
/** Offset 0x0D58 - Short term Power Limit value for custom cTDP level 2
Short term Power Limit value for custom cTDP level 2. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 Custom2PowerLimit1;
/** Offset 0x0D5C - Long term Power Limit value for custom cTDP level 2
Long term Power Limit value for custom cTDP level 2. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 Custom2PowerLimit2;
/** Offset 0x0D60 - Short term Power Limit value for custom cTDP level 3
Short term Power Limit value for custom cTDP level 3. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 Custom3PowerLimit1;
/** Offset 0x0D64 - Long term Power Limit value for custom cTDP level 3
Long term Power Limit value for custom cTDP level 3. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid
Range 0 to 4095875 in Step size of 125
**/
UINT32 Custom3PowerLimit2;
/** Offset 0x0D68 - Platform PL1 power
Platform PL1 power. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range
0 to 4095875 in Step size of 125
**/
UINT32 PsysPowerLimit1Power;
/** Offset 0x0D6C - Platform PL2 power
Platform PL2 power. Units are based on POWER_MGMT_CONFIG.CustomPowerUnit.Valid Range
0 to 4095875 in Step size of 125
**/
UINT32 PsysPowerLimit2Power;
/** Offset 0x0D70 - Race To Halt
Enable/Disable Race To Halt feature. RTH will dynamically increase CPU frequency
in order to enter pkg C-State faster to reduce overall power. (RTH is controlled
through MSR 1FC bit 20)Disable; <b>1: Enable</b>
$EN_DIS
**/
UINT8 RaceToHalt;
/** Offset 0x0D71 - Set Three Strike Counter Disable
False (default): Three Strike counter will be incremented and True: Prevents Three
Strike counter from incrementing; <b>0: False</b>; 1: True.
0: False, 1: True
**/
UINT8 ThreeStrikeCounterDisable;
/** Offset 0x0D72 - Set HW P-State Interrupts Enabled for for MISC_PWR_MGMT
Set HW P-State Interrupts Enabled for for MISC_PWR_MGMT; <b>0: Disable</b>; 1: Enable.
$EN_DIS
**/
UINT8 HwpInterruptControl;
/** Offset 0x0D73 - Reserved
**/
UINT8 Reserved89[4];
/** Offset 0x0D77 - Intel Turbo Boost Max Technology 3.0
Intel Turbo Boost Max Technology 3.0. 0: Disabled; <b>1: Enabled</b>
$EN_DIS
**/
UINT8 EnableItbm;
/** Offset 0x0D78 - Enable or Disable C1 Cstate Demotion
Enable or Disable C1 Cstate Demotion. Disable; <b>1: Enable</b>
$EN_DIS
**/
UINT8 C1StateAutoDemotion;
/** Offset 0x0D79 - Enable or Disable C1 Cstate UnDemotion
Enable or Disable C1 Cstate UnDemotion. Disable; <b>1: Enable</b>
$EN_DIS
**/
UINT8 C1StateUnDemotion;
/** Offset 0x0D7A - Minimum Ring ratio limit override
Minimum Ring ratio limit override. <b>0: Hardware defaults.</b> Range: 0 - Max turbo
ratio limit
**/
UINT8 MinRingRatioLimit;
/** Offset 0x0D7B - Maximum Ring ratio limit override
Maximum Ring ratio limit override. <b>0: Hardware defaults.</b> Range: 0 - Max turbo
ratio limit
**/
UINT8 MaxRingRatioLimit;
/** Offset 0x0D7C - Enable or Disable Per Core P State OS control
Enable or Disable Per Core P State OS control. 0: Disable; <b>1: Enable</b>
$EN_DIS
**/
UINT8 EnablePerCorePState;
/** Offset 0x0D7D - Enable or Disable HwP Autonomous Per Core P State OS control
Enable or Disable HwP Autonomous Per Core P State OS control. 0: Disable; <b>1:
Enable</b>
$EN_DIS
**/
UINT8 EnableHwpAutoPerCorePstate;
/** Offset 0x0D7E - Enable or Disable HwP Autonomous EPP Grouping
Enable or Disable HwP Autonomous EPP Grouping. 0: Disable; <b>1: Enable</b>
$EN_DIS
**/
UINT8 EnableHwpAutoEppGrouping;
/** Offset 0x0D7F - Enable or Disable EPB override over PECI
Enable or Disable EPB override over PECI. <b>0: Disable;</b> 1: Enable
$EN_DIS
**/
UINT8 EnableEpbPeciOverride;
/** Offset 0x0D80 - Enable or Disable Fast MSR for IA32_HWP_REQUEST
Enable or Disable Fast MSR for IA32_HWP_REQUEST. 0: Disable;<b> 1: Enable</b>
$EN_DIS
**/
UINT8 EnableFastMsrHwpReq;
/** Offset 0x0D81 - Enable Configurable TDP
Applies TDP initialization settings based on non-cTDP or cTDP.; 0: Applies to non-cTDP;
<b>1: Applies to cTDP</b>
$EN_DIS
**/
UINT8 ApplyConfigTdp;
/** Offset 0x0D82 - Reserved
**/
UINT8 Reserved90;
/** Offset 0x0D83 - Dual Tau Boost
Enable, Disable Dual Tau Boost feature. This is only applicable for Desktop; <b>0:
Disable</b>; 1: Enable
$EN_DIS
**/
UINT8 DualTauBoost;
/** Offset 0x0D84 - Reserved
**/
UINT8 Reserved91;
/** Offset 0x0D85 - Reserved
**/
UINT8 Reserved92;
/** Offset 0x0D86 - Reserved
**/
UINT8 Reserved93[14];
/** Offset 0x0D94 - Reserved
**/
UINT8 Reserved94[16];
/** Offset 0x0DA4 - End of Post message
Test, Send End of Post message. Disable(0x0): Disable EOP message, Send in PEI(0x1):
EOP send in PEI, Send in DXE(0x2)(Default): EOP send in DXE
0:Disable, 1:Send in PEI, 2:Send in DXE, 3:Reserved
**/
UINT8 EndOfPostMessage;
/** Offset 0x0DA5 - D0I3 Setting for HECI Disable
Test, 0: disable, 1: enable, Setting this option disables setting D0I3 bit for all
HECI devices
$EN_DIS
**/
UINT8 DisableD0I3SettingForHeci;
/** Offset 0x0DA6 - Mctp Broadcast Cycle
Test, Determine if MCTP Broadcast is enabled <b>0: Disable</b>; 1: Enable.
$EN_DIS
**/
UINT8 MctpBroadcastCycle;
/** Offset 0x0DA7 - Enable LOCKDOWN SMI
Enable SMI_LOCK bit to prevent writes to the Global SMI Enable bit.
$EN_DIS
**/
UINT8 PchLockDownGlobalSmi;
/** Offset 0x0DA8 - Enable LOCKDOWN BIOS Interface
Enable BIOS Interface Lock Down bit to prevent writes to the Backup Control Register.
$EN_DIS
**/
UINT8 PchLockDownBiosInterface;
/** Offset 0x0DA9 - Unlock all GPIO pads
Force all GPIO pads to be unlocked for debug purpose.
$EN_DIS
**/
UINT8 PchUnlockGpioPads;
/** Offset 0x0DAA - PCH Unlock SideBand access
The SideBand PortID mask for certain end point (e.g. PSFx) will be locked before
3rd party code execution. 0: Lock SideBand access; 1: Unlock SideBand access.
$EN_DIS
**/
UINT8 PchSbAccessUnlock;
/** Offset 0x0DAB - Reserved
**/
UINT8 Reserved95[1];
/** Offset 0x0DAC - PCIE RP Ltr Max Snoop Latency
Latency Tolerance Reporting, Max Snoop Latency.
**/
UINT16 PcieRpLtrMaxSnoopLatency[28];
/** Offset 0x0DE4 - PCIE RP Ltr Max No Snoop Latency
Latency Tolerance Reporting, Max Non-Snoop Latency.
**/
UINT16 PcieRpLtrMaxNoSnoopLatency[28];
/** Offset 0x0E1C - PCIE RP Snoop Latency Override Mode
Latency Tolerance Reporting, Snoop Latency Override Mode.
**/
UINT8 PcieRpSnoopLatencyOverrideMode[28];
/** Offset 0x0E38 - PCIE RP Snoop Latency Override Multiplier
Latency Tolerance Reporting, Snoop Latency Override Multiplier.
**/
UINT8 PcieRpSnoopLatencyOverrideMultiplier[28];
/** Offset 0x0E54 - PCIE RP Snoop Latency Override Value
Latency Tolerance Reporting, Snoop Latency Override Value.
**/
UINT16 PcieRpSnoopLatencyOverrideValue[28];
/** Offset 0x0E8C - PCIE RP Non Snoop Latency Override Mode
Latency Tolerance Reporting, Non-Snoop Latency Override Mode.
**/
UINT8 PcieRpNonSnoopLatencyOverrideMode[28];
/** Offset 0x0EA8 - PCIE RP Non Snoop Latency Override Multiplier
Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier.
**/
UINT8 PcieRpNonSnoopLatencyOverrideMultiplier[28];
/** Offset 0x0EC4 - PCIE RP Non Snoop Latency Override Value
Latency Tolerance Reporting, Non-Snoop Latency Override Value.
**/
UINT16 PcieRpNonSnoopLatencyOverrideValue[28];
/** Offset 0x0EFC - PCIE RP Slot Power Limit Scale
Specifies scale used for slot power limit value. Leave as 0 to set to default.
**/
UINT8 PcieRpSlotPowerLimitScale[28];
/** Offset 0x0F18 - PCIE RP Slot Power Limit Value
Specifies upper limit on power supplie by slot. Leave as 0 to set to default.
**/
UINT16 PcieRpSlotPowerLimitValue[28];
/** Offset 0x0F50 - PCIE RP Enable Port8xh Decode
This member describes whether PCIE root port Port 8xh Decode is enabled. 0: Disable;
1: Enable.
$EN_DIS
**/
UINT8 PcieEnablePort8xhDecode;
/** Offset 0x0F51 - PCIE Port8xh Decode Port Index
The Index of PCIe Port that is selected for Port8xh Decode (0 Based).
**/
UINT8 PchPciePort8xhDecodePortIndex;
/** Offset 0x0F52 - PCH Energy Reporting
Disable/Enable PCH to CPU energy report feature.
$EN_DIS
**/
UINT8 PchPmDisableEnergyReport;
/** Offset 0x0F53 - PCH Sata Test Mode
Allow entrance to the PCH SATA test modes.
$EN_DIS
**/
UINT8 SataTestMode;
/** Offset 0x0F54 - PCH USB OverCurrent mapping lock enable
If this policy option is enabled then BIOS will program OCCFDONE bit in xHCI meaning
that OC mapping data will be consumed by xHCI and OC mapping registers will be locked.
$EN_DIS
**/
UINT8 PchXhciOcLock;
/** Offset 0x0F55 - Low Power Mode Enable/Disable config mask
Configure if respective S0i2/3 sub-states are to be supported. Each bit corresponds
to one sub-state (LPMx - BITx): LPM0-s0i2.0, LPM1-s0i2.1, LPM2-s0i2.2, LPM3-s0i3.0,
LPM4-s0i3.1, LPM5-s0i3.2, LPM6-s0i3.3, LPM7-s0i3.4.
**/
UINT8 PmcLpmS0ixSubStateEnableMask;
/** Offset 0x0F56 - PCIE RP Ltr Max Snoop Latency
Latency Tolerance Reporting, Max Snoop Latency.
**/
UINT16 CpuPcieRpLtrMaxSnoopLatency[4];
/** Offset 0x0F5E - PCIE RP Ltr Max No Snoop Latency
Latency Tolerance Reporting, Max Non-Snoop Latency.
**/
UINT16 CpuPcieRpLtrMaxNoSnoopLatency[4];
/** Offset 0x0F66 - PCIE RP Snoop Latency Override Mode
Latency Tolerance Reporting, Snoop Latency Override Mode.
**/
UINT8 CpuPcieRpSnoopLatencyOverrideMode[4];
/** Offset 0x0F6A - PCIE RP Snoop Latency Override Multiplier
Latency Tolerance Reporting, Snoop Latency Override Multiplier.
**/
UINT8 CpuPcieRpSnoopLatencyOverrideMultiplier[4];
/** Offset 0x0F6E - PCIE RP Snoop Latency Override Value
Latency Tolerance Reporting, Snoop Latency Override Value.
**/
UINT16 CpuPcieRpSnoopLatencyOverrideValue[4];
/** Offset 0x0F76 - PCIE RP Non Snoop Latency Override Mode
Latency Tolerance Reporting, Non-Snoop Latency Override Mode.
**/
UINT8 CpuPcieRpNonSnoopLatencyOverrideMode[4];
/** Offset 0x0F7A - PCIE RP Non Snoop Latency Override Multiplier
Latency Tolerance Reporting, Non-Snoop Latency Override Multiplier.
**/
UINT8 CpuPcieRpNonSnoopLatencyOverrideMultiplier[4];
/** Offset 0x0F7E - PCIE RP Non Snoop Latency Override Value
Latency Tolerance Reporting, Non-Snoop Latency Override Value.
**/
UINT16 CpuPcieRpNonSnoopLatencyOverrideValue[4];
/** Offset 0x0F86 - PCIE RP Upstream Port Transmiter Preset
Used during Gen3 Link Equalization. Used for all lanes. Default is 7.
**/
UINT8 CpuPcieRpGen3Uptp[4];
/** Offset 0x0F8A - PCIE RP Downstream Port Transmiter Preset
Used during Gen3 Link Equalization. Used for all lanes. Default is 7.
**/
UINT8 CpuPcieRpGen3Dptp[4];
/** Offset 0x0F8E - PCIE RP Upstream Port Transmiter Preset
Used during Gen4 Link Equalization. Used for all lanes. Default is 8.
**/
UINT8 CpuPcieRpGen4Uptp[4];
/** Offset 0x0F92 - PCIE RP Downstream Port Transmiter Preset
Used during Gen4 Link Equalization. Used for all lanes. Default is 9.
**/
UINT8 CpuPcieRpGen4Dptp[4];
/** Offset 0x0F96 - Reserved
**/
UINT8 Reserved96[4];
/** Offset 0x0F9A - Reserved
**/
UINT8 Reserved97[4];
/** Offset 0x0F9E - Reserved
**/
UINT8 Reserved98[4];
/** Offset 0x0FA2 - Reserved
**/
UINT8 Reserved99[4];
/** Offset 0x0FA6 - FOMS Control Policy
Choose the Foms Control Policy, <b>Default = 0 </b>
0: Auto, 1: Gen3 Foms, 2: Gen4 Foms, 3: Gen3 and Gen4 Foms
**/
UINT8 CpuPcieFomsCp[4];
/** Offset 0x0FAA - PMC C10 dynamic threshold dajustment enable
Set if you want to enable PMC C10 dynamic threshold adjustment. Only works on supported SKUs
$EN_DIS
**/
UINT8 PmcC10DynamicThresholdAdjustment;
/** Offset 0x0FAB - P2P mode for PCIE RP
Enable/disable peer to peer mode for PCIE Root Ports. 0: Disable, 1: Enable.
0: Disable, 1: Enable
**/
UINT8 CpuPcieRpPeerToPeerMode[4];
/** Offset 0x0FAF - Reserved
**/
UINT8 Reserved100[8];
/** Offset 0x0FB7 - Reserved
**/
UINT8 Reserved101[8];
/** Offset 0x0FBF - Reserved
**/
UINT8 Reserved102[8];
/** Offset 0x0FC7 - Reserved
**/
UINT8 Reserved103[8];
/** Offset 0x0FCF - Reserved
**/
UINT8 Reserved104;
/** Offset 0x0FD0 - FspEventHandler
<b>Optional</b> pointer to the boot loader's implementation of FSP_EVENT_HANDLER.
**/
UINT32 FspEventHandler;
/** Offset 0x0FD4 - Enable VMD Global Mapping
Enable/disable to VMD controller.0: Disable; 1: Enable(Default)
$EN_DIS
**/
UINT8 VmdGlobalMapping;
/** Offset 0x0FD5 - Reserved
**/
UINT8 Reserved105[4];
/** Offset 0x0FD9 - Reserved
**/
UINT8 Reserved106;
/** Offset 0x0FDA - Reserved
**/
UINT8 Reserved107;
/** Offset 0x0FDB - Reserved
**/
UINT8 Reserved108;
/** Offset 0x0FDC - Reserved
**/
UINT32 Reserved109;
/** Offset 0x0FE0 - Reserved
**/
UINT32 Reserved110;
/** Offset 0x0FE4 - Reserved
**/
UINT32 Reserved111[2];
/** Offset 0x0FEC - Reserved
**/
UINT32 Reserved112[2];
/** Offset 0x0FF4 - Reserved
**/
UINT32 Reserved113[2];
/** Offset 0x0FFC - Reserved
**/
UINT32 Reserved114[2];
/** Offset 0x1004 - Reserved
**/
UINT32 Reserved115[2];
/** Offset 0x100C - Reserved
**/
UINT32 Reserved116[2];
/** Offset 0x1014 - Reserved
**/
UINT32 Reserved117[2];
/** Offset 0x101C - Reserved
**/
UINT32 Reserved118[2];
/** Offset 0x1024 - Reserved
**/
UINT32 Reserved119[2];
/** Offset 0x102C - Reserved
**/
UINT32 Reserved120[2];
/** Offset 0x1034 - Reserved
**/
UINT32 Reserved121[2];
/** Offset 0x103C - Reserved
**/
UINT32 Reserved122[2];
/** Offset 0x1044 - Reserved
**/
UINT32 Reserved123[2];
/** Offset 0x104C - Reserved
**/
UINT8 Reserved124[4];
/** Offset 0x1050 - Reserved
**/
UINT64 Reserved125;
/** Offset 0x1058 - Reserved
**/
UINT32 Reserved126;
/** Offset 0x105C - Reserved
**/
UINT8 Reserved127[2];
/** Offset 0x105E - Reserved
**/
UINT8 Reserved128[2];
} FSP_S_CONFIG;
/** Fsp S UPD Configuration
**/
typedef struct {
/** Offset 0x0000
**/
FSP_UPD_HEADER FspUpdHeader;
/** Offset 0x0020
**/
FSPS_ARCH_UPD FspsArchUpd;
/** Offset 0x0040
**/
FSP_S_CONFIG FspsConfig;
/** Offset 0x1060
**/
UINT8 UnusedUpdSpace42[6];
/** Offset 0x1066
**/
UINT16 UpdTerminator;
} FSPS_UPD;
#pragma pack()
#endif