blob: dabb4a1ccdcf70150db023a2815e460e87ea6333 [file] [log] [blame]
# SPDX-License-Identifier: GPL-2.0-only
config DRM_MSM
tristate "MSM DRM"
depends on DRM
depends on ARCH_QCOM || SOC_IMX5 || (ARM && COMPILE_TEST)
depends on IOMMU_SUPPORT
depends on OF && COMMON_CLK
depends on QCOM_OCMEM || QCOM_OCMEM=n
select IOMMU_IO_PGTABLE
select QCOM_MDT_LOADER if ARCH_QCOM
select REGULATOR
select DRM_KMS_HELPER
select DRM_PANEL
select SHMEM
select TMPFS
select QCOM_SCM if ARCH_QCOM
select QCOM_COMMAND_DB if ARCH_QCOM
select WANT_DEV_COREDUMP
select SND_SOC_HDMI_CODEC if SND_SOC
select SYNC_FILE
select PM_OPP
help
DRM/KMS driver for MSM/snapdragon.
config DRM_MSM_GPU_STATE
bool
depends on DRM_MSM && (DEBUG_FS || DEV_COREDUMP)
default y
config DRM_MSM_REGISTER_LOGGING
bool "MSM DRM register logging"
depends on DRM_MSM
default n
help
Compile in support for logging register reads/writes in a format
that can be parsed by envytools demsm tool. If enabled, register
logging can be switched on via msm.reglog=y module param.
config DRM_MSM_GPU_SUDO
bool "Enable SUDO flag on submits"
depends on DRM_MSM && EXPERT
default n
help
Enable userspace that has CAP_SYS_RAWIO to submit GPU commands
that are run from RB instead of IB1. This essentially gives
userspace kernel level access, but is useful for firmware
debugging.
Only use this if you are a driver developer. This should *not*
be enabled for production kernels. If unsure, say N.
config DRM_MSM_HDMI_HDCP
bool "Enable HDMI HDCP support in MSM DRM driver"
depends on DRM_MSM && QCOM_SCM
default y
help
Choose this option to enable HDCP state machine
config DRM_MSM_DP
bool "Enable DisplayPort support in MSM DRM driver"
depends on DRM_MSM
default y
help
Compile in support for DP driver in MSM DRM driver. DP external
display support is enabled through this config option. It can
be primary or secondary display on device.
config DRM_MSM_DSI
bool "Enable DSI support in MSM DRM driver"
depends on DRM_MSM
select DRM_PANEL
select DRM_MIPI_DSI
default y
help
Choose this option if you have a need for MIPI DSI connector
support.
config DRM_MSM_DSI_PLL
bool "Enable DSI PLL driver in MSM DRM"
depends on DRM_MSM_DSI && COMMON_CLK
default y
help
Choose this option to enable DSI PLL driver which provides DSI
source clocks under common clock framework.
config DRM_MSM_DSI_28NM_PHY
bool "Enable DSI 28nm PHY driver in MSM DRM"
depends on DRM_MSM_DSI
default y
help
Choose this option if the 28nm DSI PHY is used on the platform.
config DRM_MSM_DSI_20NM_PHY
bool "Enable DSI 20nm PHY driver in MSM DRM"
depends on DRM_MSM_DSI
default y
help
Choose this option if the 20nm DSI PHY is used on the platform.
config DRM_MSM_DSI_28NM_8960_PHY
bool "Enable DSI 28nm 8960 PHY driver in MSM DRM"
depends on DRM_MSM_DSI
default y
help
Choose this option if the 28nm DSI PHY 8960 variant is used on the
platform.
config DRM_MSM_DSI_14NM_PHY
bool "Enable DSI 14nm PHY driver in MSM DRM (used by MSM8996/APQ8096)"
depends on DRM_MSM_DSI
default y
help
Choose this option if DSI PHY on 8996 is used on the platform.
config DRM_MSM_DSI_10NM_PHY
bool "Enable DSI 10nm PHY driver in MSM DRM (used by SDM845)"
depends on DRM_MSM_DSI
default y
help
Choose this option if DSI PHY on SDM845 is used on the platform.
config DRM_MSM_DSI_7NM_PHY
bool "Enable DSI 7nm PHY driver in MSM DRM (used by SM8150/SM8250)"
depends on DRM_MSM_DSI
default y
help
Choose this option if DSI PHY on SM8150/SM8250 is used on the
platform.