| /* SPDX-License-Identifier: GPL-2.0-or-later */ | |
| /* | |
| * Header file for UHS-II packets, Host Controller registers and I/O | |
| * accessors. | |
| * | |
| * Copyright (C) 2014 Intel Corp, All Rights Reserved. | |
| */ | |
| #ifndef LINUX_MMC_UHS2_H | |
| #define LINUX_MMC_UHS2_H | |
| /* LINK Layer definition */ | |
| /* | |
| * UHS2 Header: | |
| * Refer to UHS-II Addendum Version 1.02 Figure 5-2, the format of CCMD Header is described below: | |
| * bit [3:0] : DID(Destination ID = Node ID of UHS2 card) | |
| * bit [6:4] : TYP(Packet Type) | |
| * 000b: CCMD(Control command packet) | |
| * 001b: DCMD(Data command packet) | |
| * 010b: RES(Response packet) | |
| * 011b: DATA(Data payload packet) | |
| * 111b: MSG(Message packet) | |
| * Others: Reserved | |
| * bit [7] : NP(Native Packet) | |
| * bit [10:8] : TID(Transaction ID) | |
| * bit [11] : Reserved | |
| * bit [15:12]: SID(Source ID 0: Node ID of Host) | |
| * | |
| * Broadcast CCMD issued by Host is represented as DID=SID=0. | |
| */ | |
| /* | |
| * UHS2 Argument: | |
| * Refer to UHS-II Addendum Version 1.02 Figure 6-5, the format of CCMD Argument is described below: | |
| * bit [3:0] : MSB of IOADR | |
| * bit [5:4] : PLEN(Payload Length) | |
| * 00b: 0 byte | |
| * 01b: 4 bytes | |
| * 10b: 8 bytes | |
| * 11b: 16 bytes | |
| * bit [6] : Reserved | |
| * bit [7] : R/W(Read/Write) | |
| * 0: Control read command | |
| * 1: Control write command | |
| * bit [15:8] : LSB of IOADR | |
| * | |
| * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD. | |
| * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last. | |
| */ | |
| #define UHS2_NATIVE_PACKET_POS 7 | |
| #define UHS2_NATIVE_PACKET (1 << UHS2_NATIVE_PACKET_POS) | |
| #define UHS2_PACKET_TYPE_POS 4 | |
| #define UHS2_PACKET_TYPE_CCMD (0 << UHS2_PACKET_TYPE_POS) | |
| #define UHS2_PACKET_TYPE_DCMD (1 << UHS2_PACKET_TYPE_POS) | |
| #define UHS2_PACKET_TYPE_RES (2 << UHS2_PACKET_TYPE_POS) | |
| #define UHS2_PACKET_TYPE_DATA (3 << UHS2_PACKET_TYPE_POS) | |
| #define UHS2_PACKET_TYPE_MSG (7 << UHS2_PACKET_TYPE_POS) | |
| #define UHS2_DEST_ID_MASK 0x0F | |
| #define UHS2_DEST_ID 0x1 | |
| #define UHS2_SRC_ID_POS 12 | |
| #define UHS2_SRC_ID_MASK 0xF000 | |
| #define UHS2_TRANS_ID_POS 8 | |
| #define UHS2_TRANS_ID_MASK 0x0700 | |
| /* UHS2 MSG */ | |
| #define UHS2_MSG_CTG_POS 5 | |
| #define UHS2_MSG_CTG_LMSG 0x00 | |
| #define UHS2_MSG_CTG_INT 0x60 | |
| #define UHS2_MSG_CTG_AMSG 0x80 | |
| #define UHS2_MSG_CTG_FCREQ 0x00 | |
| #define UHS2_MSG_CTG_FCRDY 0x01 | |
| #define UHS2_MSG_CTG_STAT 0x02 | |
| #define UHS2_MSG_CODE_POS 8 | |
| #define UHS2_MSG_CODE_FC_UNRECOVER_ERR 0x8 | |
| #define UHS2_MSG_CODE_STAT_UNRECOVER_ERR 0x8 | |
| #define UHS2_MSG_CODE_STAT_RECOVER_ERR 0x1 | |
| /* TRANS Layer definition */ | |
| /* Native packets*/ | |
| #define UHS2_NATIVE_CMD_RW_POS 7 | |
| #define UHS2_NATIVE_CMD_WRITE (1 << UHS2_NATIVE_CMD_RW_POS) | |
| #define UHS2_NATIVE_CMD_READ (0 << UHS2_NATIVE_CMD_RW_POS) | |
| #define UHS2_NATIVE_CMD_PLEN_POS 4 | |
| #define UHS2_NATIVE_CMD_PLEN_4B (1 << UHS2_NATIVE_CMD_PLEN_POS) | |
| #define UHS2_NATIVE_CMD_PLEN_8B (2 << UHS2_NATIVE_CMD_PLEN_POS) | |
| #define UHS2_NATIVE_CMD_PLEN_16B (3 << UHS2_NATIVE_CMD_PLEN_POS) | |
| #define UHS2_NATIVE_CCMD_GET_MIOADR_MASK 0xF00 | |
| #define UHS2_NATIVE_CCMD_MIOADR_MASK 0x0F | |
| #define UHS2_NATIVE_CCMD_LIOADR_POS 8 | |
| #define UHS2_NATIVE_CCMD_GET_LIOADR_MASK 0x0FF | |
| #define UHS2_CCMD_DEV_INIT_COMPLETE_FLAG BIT(11) | |
| #define UHS2_DEV_INIT_PAYLOAD_LEN 1 | |
| #define UHS2_DEV_INIT_RESP_LEN 6 | |
| #define UHS2_DEV_ENUM_PAYLOAD_LEN 1 | |
| #define UHS2_DEV_ENUM_RESP_LEN 8 | |
| #define UHS2_CFG_WRITE_PAYLOAD_LEN 2 | |
| #define UHS2_CFG_WRITE_PHY_SET_RESP_LEN 4 | |
| #define UHS2_CFG_WRITE_GENERIC_SET_RESP_LEN 5 | |
| #define UHS2_GO_DORMANT_PAYLOAD_LEN 1 | |
| /* | |
| * UHS2 Argument: | |
| * Refer to UHS-II Addendum Version 1.02 Figure 6-8, the format of DCMD Argument is described below: | |
| * bit [3:0] : Reserved | |
| * bit [6:3] : TMODE(Transfer Mode) | |
| * bit 3: DAM(Data Access Mode) | |
| * bit 4: TLUM(TLEN Unit Mode) | |
| * bit 5: LM(Length Mode) | |
| * bit 6: DM(Duplex Mode) | |
| * bit [7] : R/W(Read/Write) | |
| * 0: Control read command | |
| * 1: Control write command | |
| * bit [15:8] : Reserved | |
| * | |
| * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD. | |
| * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last. | |
| */ | |
| #define UHS2_DCMD_DM_POS 6 | |
| #define UHS2_DCMD_2L_HD_MODE (1 << UHS2_DCMD_DM_POS) | |
| #define UHS2_DCMD_LM_POS 5 | |
| #define UHS2_DCMD_LM_TLEN_EXIST (1 << UHS2_DCMD_LM_POS) | |
| #define UHS2_DCMD_TLUM_POS 4 | |
| #define UHS2_DCMD_TLUM_BYTE_MODE (1 << UHS2_DCMD_TLUM_POS) | |
| #define UHS2_NATIVE_DCMD_DAM_POS 3 | |
| #define UHS2_NATIVE_DCMD_DAM_IO (1 << UHS2_NATIVE_DCMD_DAM_POS) | |
| #define UHS2_RES_NACK_POS 7 | |
| #define UHS2_RES_NACK_MASK (0x1 << UHS2_RES_NACK_POS) | |
| #define UHS2_RES_ECODE_POS 4 | |
| #define UHS2_RES_ECODE_MASK 0x7 | |
| #define UHS2_RES_ECODE_COND 1 | |
| #define UHS2_RES_ECODE_ARG 2 | |
| #define UHS2_RES_ECODE_GEN 3 | |
| /* IOADR of device registers */ | |
| #define UHS2_IOADR_GENERIC_CAPS 0x00 | |
| #define UHS2_IOADR_PHY_CAPS 0x02 | |
| #define UHS2_IOADR_LINK_CAPS 0x04 | |
| #define UHS2_IOADR_RSV_CAPS 0x06 | |
| #define UHS2_IOADR_GENERIC_SETTINGS 0x08 | |
| #define UHS2_IOADR_PHY_SETTINGS 0x0A | |
| #define UHS2_IOADR_LINK_SETTINGS 0x0C | |
| #define UHS2_IOADR_PRESET 0x40 | |
| /* SD application packets */ | |
| #define UHS2_SD_CMD_INDEX_POS 8 | |
| #define UHS2_SD_CMD_APP_POS 14 | |
| #define UHS2_SD_CMD_APP (1 << UHS2_SD_CMD_APP_POS) | |
| /* UHS-II Device Registers */ | |
| #define UHS2_DEV_CONFIG_REG 0x000 | |
| /* General Caps and Settings registers */ | |
| #define UHS2_DEV_CONFIG_GEN_CAPS (UHS2_DEV_CONFIG_REG + 0x000) | |
| #define UHS2_DEV_CONFIG_N_LANES_POS 8 | |
| #define UHS2_DEV_CONFIG_N_LANES_MASK 0x3F | |
| #define UHS2_DEV_CONFIG_2L_HD_FD 0x1 | |
| #define UHS2_DEV_CONFIG_2D1U_FD 0x2 | |
| #define UHS2_DEV_CONFIG_1D2U_FD 0x4 | |
| #define UHS2_DEV_CONFIG_2D2U_FD 0x8 | |
| #define UHS2_DEV_CONFIG_DADR_POS 14 | |
| #define UHS2_DEV_CONFIG_DADR_MASK 0x1 | |
| #define UHS2_DEV_CONFIG_APP_POS 16 | |
| #define UHS2_DEV_CONFIG_APP_MASK 0xFF | |
| #define UHS2_DEV_CONFIG_APP_SD_MEM 0x1 | |
| #define UHS2_DEV_CONFIG_GEN_SET (UHS2_DEV_CONFIG_REG + 0x008) | |
| #define UHS2_DEV_CONFIG_GEN_SET_N_LANES_POS 8 | |
| #define UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD 0x0 | |
| #define UHS2_DEV_CONFIG_GEN_SET_2D1U_FD 0x2 | |
| #define UHS2_DEV_CONFIG_GEN_SET_1D2U_FD 0x3 | |
| #define UHS2_DEV_CONFIG_GEN_SET_2D2U_FD 0x4 | |
| #define UHS2_DEV_CONFIG_GEN_SET_CFG_COMPLETE BIT(31) | |
| /* PHY Caps and Settings registers */ | |
| #define UHS2_DEV_CONFIG_PHY_CAPS (UHS2_DEV_CONFIG_REG + 0x002) | |
| #define UHS2_DEV_CONFIG_PHY_MINOR_MASK 0xF | |
| #define UHS2_DEV_CONFIG_PHY_MAJOR_POS 4 | |
| #define UHS2_DEV_CONFIG_PHY_MAJOR_MASK 0x3 | |
| #define UHS2_DEV_CONFIG_CAN_HIBER_POS 15 | |
| #define UHS2_DEV_CONFIG_CAN_HIBER_MASK 0x1 | |
| #define UHS2_DEV_CONFIG_PHY_CAPS1 (UHS2_DEV_CONFIG_REG + 0x003) | |
| #define UHS2_DEV_CONFIG_N_LSS_SYN_MASK 0xF | |
| #define UHS2_DEV_CONFIG_N_LSS_DIR_POS 4 | |
| #define UHS2_DEV_CONFIG_N_LSS_DIR_MASK 0xF | |
| #define UHS2_DEV_CONFIG_PHY_SET (UHS2_DEV_CONFIG_REG + 0x00A) | |
| #define UHS2_DEV_CONFIG_PHY_SET_SPEED_POS 6 | |
| #define UHS2_DEV_CONFIG_PHY_SET_SPEED_A 0x0 | |
| #define UHS2_DEV_CONFIG_PHY_SET_SPEED_B 0x1 | |
| /* LINK-TRAN Caps and Settings registers */ | |
| #define UHS2_DEV_CONFIG_LINK_TRAN_CAPS (UHS2_DEV_CONFIG_REG + 0x004) | |
| #define UHS2_DEV_CONFIG_LT_MINOR_MASK 0xF | |
| #define UHS2_DEV_CONFIG_LT_MAJOR_POS 4 | |
| #define UHS2_DEV_CONFIG_LT_MAJOR_MASK 0x3 | |
| #define UHS2_DEV_CONFIG_N_FCU_POS 8 | |
| #define UHS2_DEV_CONFIG_N_FCU_MASK 0xFF | |
| #define UHS2_DEV_CONFIG_DEV_TYPE_POS 16 | |
| #define UHS2_DEV_CONFIG_DEV_TYPE_MASK 0x7 | |
| #define UHS2_DEV_CONFIG_MAX_BLK_LEN_POS 20 | |
| #define UHS2_DEV_CONFIG_MAX_BLK_LEN_MASK 0xFFF | |
| #define UHS2_DEV_CONFIG_LINK_TRAN_CAPS1 (UHS2_DEV_CONFIG_REG + 0x005) | |
| #define UHS2_DEV_CONFIG_N_DATA_GAP_MASK 0xFF | |
| #define UHS2_DEV_CONFIG_LINK_TRAN_SET (UHS2_DEV_CONFIG_REG + 0x00C) | |
| #define UHS2_DEV_CONFIG_LT_SET_MAX_BLK_LEN 0x200 | |
| #define UHS2_DEV_CONFIG_LT_SET_MAX_RETRY_POS 16 | |
| /* Preset register */ | |
| #define UHS2_DEV_CONFIG_PRESET (UHS2_DEV_CONFIG_REG + 0x040) | |
| #define UHS2_DEV_INT_REG 0x100 | |
| #define UHS2_DEV_STATUS_REG 0x180 | |
| #define UHS2_DEV_CMD_REG 0x200 | |
| #define UHS2_DEV_CMD_FULL_RESET (UHS2_DEV_CMD_REG + 0x000) | |
| #define UHS2_DEV_CMD_GO_DORMANT_STATE (UHS2_DEV_CMD_REG + 0x001) | |
| #define UHS2_DEV_CMD_DORMANT_HIBER BIT(7) | |
| #define UHS2_DEV_CMD_DEVICE_INIT (UHS2_DEV_CMD_REG + 0x002) | |
| #define UHS2_DEV_INIT_COMPLETE_FLAG BIT(11) | |
| #define UHS2_DEV_CMD_ENUMERATE (UHS2_DEV_CMD_REG + 0x003) | |
| #define UHS2_DEV_CMD_TRANS_ABORT (UHS2_DEV_CMD_REG + 0x004) | |
| #define UHS2_RCLK_MAX 52000000 | |
| #define UHS2_RCLK_MIN 26000000 | |
| #endif /* LINUX_MMC_UHS2_H */ |