| // SPDX-License-Identifier: GPL-2.0 | |
| /* | |
| * LiteUART serial controller (LiteX) Driver | |
| * | |
| * Copyright (C) 2019-2020 Antmicro <www.antmicro.com> | |
| */ | |
| #include <linux/bits.h> | |
| #include <linux/console.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/litex.h> | |
| #include <linux/module.h> | |
| #include <linux/of.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/serial.h> | |
| #include <linux/serial_core.h> | |
| #include <linux/slab.h> | |
| #include <linux/timer.h> | |
| #include <linux/tty_flip.h> | |
| #include <linux/xarray.h> | |
| /* | |
| * CSRs definitions (base address offsets + width) | |
| * | |
| * The definitions below are true for LiteX SoC configured for 8-bit CSR Bus, | |
| * 32-bit aligned. | |
| * | |
| * Supporting other configurations might require new definitions or a more | |
| * generic way of indexing the LiteX CSRs. | |
| * | |
| * For more details on how CSRs are defined and handled in LiteX, see comments | |
| * in the LiteX SoC Driver: drivers/soc/litex/litex_soc_ctrl.c | |
| */ | |
| #define OFF_RXTX 0x00 | |
| #define OFF_TXFULL 0x04 | |
| #define OFF_RXEMPTY 0x08 | |
| #define OFF_EV_STATUS 0x0c | |
| #define OFF_EV_PENDING 0x10 | |
| #define OFF_EV_ENABLE 0x14 | |
| /* events */ | |
| #define EV_TX BIT(0) | |
| #define EV_RX BIT(1) | |
| struct liteuart_port { | |
| struct uart_port port; | |
| struct timer_list timer; | |
| u8 irq_reg; | |
| }; | |
| #define to_liteuart_port(port) container_of(port, struct liteuart_port, port) | |
| static DEFINE_XARRAY_FLAGS(liteuart_array, XA_FLAGS_ALLOC); | |
| #ifdef CONFIG_SERIAL_LITEUART_CONSOLE | |
| static struct console liteuart_console; | |
| #endif | |
| static struct uart_driver liteuart_driver = { | |
| .owner = THIS_MODULE, | |
| .driver_name = KBUILD_MODNAME, | |
| .dev_name = "ttyLXU", | |
| .major = 0, | |
| .minor = 0, | |
| .nr = CONFIG_SERIAL_LITEUART_MAX_PORTS, | |
| #ifdef CONFIG_SERIAL_LITEUART_CONSOLE | |
| .cons = &liteuart_console, | |
| #endif | |
| }; | |
| static void liteuart_update_irq_reg(struct uart_port *port, bool set, u8 mask) | |
| { | |
| struct liteuart_port *uart = to_liteuart_port(port); | |
| if (set) | |
| uart->irq_reg |= mask; | |
| else | |
| uart->irq_reg &= ~mask; | |
| if (port->irq) | |
| litex_write8(port->membase + OFF_EV_ENABLE, uart->irq_reg); | |
| } | |
| static void liteuart_stop_tx(struct uart_port *port) | |
| { | |
| liteuart_update_irq_reg(port, false, EV_TX); | |
| } | |
| static void liteuart_start_tx(struct uart_port *port) | |
| { | |
| liteuart_update_irq_reg(port, true, EV_TX); | |
| } | |
| static void liteuart_stop_rx(struct uart_port *port) | |
| { | |
| struct liteuart_port *uart = to_liteuart_port(port); | |
| /* just delete timer */ | |
| timer_delete(&uart->timer); | |
| } | |
| static void liteuart_rx_chars(struct uart_port *port) | |
| { | |
| unsigned char __iomem *membase = port->membase; | |
| u8 ch; | |
| while (!litex_read8(membase + OFF_RXEMPTY)) { | |
| ch = litex_read8(membase + OFF_RXTX); | |
| port->icount.rx++; | |
| /* necessary for RXEMPTY to refresh its value */ | |
| litex_write8(membase + OFF_EV_PENDING, EV_RX); | |
| /* no overflow bits in status */ | |
| if (!(uart_handle_sysrq_char(port, ch))) | |
| uart_insert_char(port, 1, 0, ch, TTY_NORMAL); | |
| } | |
| tty_flip_buffer_push(&port->state->port); | |
| } | |
| static void liteuart_tx_chars(struct uart_port *port) | |
| { | |
| u8 ch; | |
| uart_port_tx(port, ch, | |
| !litex_read8(port->membase + OFF_TXFULL), | |
| litex_write8(port->membase + OFF_RXTX, ch)); | |
| } | |
| static irqreturn_t liteuart_interrupt(int irq, void *data) | |
| { | |
| struct liteuart_port *uart = data; | |
| struct uart_port *port = &uart->port; | |
| unsigned long flags; | |
| u8 isr; | |
| /* | |
| * if polling, the context would be "in_serving_softirq", so use | |
| * irq[save|restore] spin_lock variants to cover all possibilities | |
| */ | |
| uart_port_lock_irqsave(port, &flags); | |
| isr = litex_read8(port->membase + OFF_EV_PENDING) & uart->irq_reg; | |
| if (isr & EV_RX) | |
| liteuart_rx_chars(port); | |
| if (isr & EV_TX) | |
| liteuart_tx_chars(port); | |
| uart_port_unlock_irqrestore(port, flags); | |
| return IRQ_RETVAL(isr); | |
| } | |
| static void liteuart_timer(struct timer_list *t) | |
| { | |
| struct liteuart_port *uart = timer_container_of(uart, t, timer); | |
| struct uart_port *port = &uart->port; | |
| liteuart_interrupt(0, port); | |
| mod_timer(&uart->timer, jiffies + uart_poll_timeout(port)); | |
| } | |
| static unsigned int liteuart_tx_empty(struct uart_port *port) | |
| { | |
| /* not really tx empty, just checking if tx is not full */ | |
| if (!litex_read8(port->membase + OFF_TXFULL)) | |
| return TIOCSER_TEMT; | |
| return 0; | |
| } | |
| static void liteuart_set_mctrl(struct uart_port *port, unsigned int mctrl) | |
| { | |
| /* modem control register is not present in LiteUART */ | |
| } | |
| static unsigned int liteuart_get_mctrl(struct uart_port *port) | |
| { | |
| return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; | |
| } | |
| static int liteuart_startup(struct uart_port *port) | |
| { | |
| struct liteuart_port *uart = to_liteuart_port(port); | |
| unsigned long flags; | |
| int ret; | |
| if (port->irq) { | |
| ret = request_irq(port->irq, liteuart_interrupt, 0, | |
| KBUILD_MODNAME, uart); | |
| if (ret) { | |
| dev_warn(port->dev, | |
| "line %d irq %d failed: switch to polling\n", | |
| port->line, port->irq); | |
| port->irq = 0; | |
| } | |
| } | |
| uart_port_lock_irqsave(port, &flags); | |
| /* only enabling rx irqs during startup */ | |
| liteuart_update_irq_reg(port, true, EV_RX); | |
| uart_port_unlock_irqrestore(port, flags); | |
| if (!port->irq) { | |
| timer_setup(&uart->timer, liteuart_timer, 0); | |
| mod_timer(&uart->timer, jiffies + uart_poll_timeout(port)); | |
| } | |
| return 0; | |
| } | |
| static void liteuart_shutdown(struct uart_port *port) | |
| { | |
| struct liteuart_port *uart = to_liteuart_port(port); | |
| unsigned long flags; | |
| uart_port_lock_irqsave(port, &flags); | |
| liteuart_update_irq_reg(port, false, EV_RX | EV_TX); | |
| uart_port_unlock_irqrestore(port, flags); | |
| if (port->irq) | |
| free_irq(port->irq, port); | |
| else | |
| timer_delete_sync(&uart->timer); | |
| } | |
| static void liteuart_set_termios(struct uart_port *port, struct ktermios *new, | |
| const struct ktermios *old) | |
| { | |
| unsigned int baud; | |
| unsigned long flags; | |
| uart_port_lock_irqsave(port, &flags); | |
| /* update baudrate */ | |
| baud = uart_get_baud_rate(port, new, old, 0, 460800); | |
| uart_update_timeout(port, new->c_cflag, baud); | |
| uart_port_unlock_irqrestore(port, flags); | |
| } | |
| static const char *liteuart_type(struct uart_port *port) | |
| { | |
| return "liteuart"; | |
| } | |
| static void liteuart_config_port(struct uart_port *port, int flags) | |
| { | |
| /* | |
| * Driver core for serial ports forces a non-zero value for port type. | |
| * Write an arbitrary value here to accommodate the serial core driver, | |
| * as ID part of UAPI is redundant. | |
| */ | |
| port->type = 1; | |
| } | |
| static int liteuart_verify_port(struct uart_port *port, | |
| struct serial_struct *ser) | |
| { | |
| if (port->type != PORT_UNKNOWN && ser->type != 1) | |
| return -EINVAL; | |
| return 0; | |
| } | |
| static const struct uart_ops liteuart_ops = { | |
| .tx_empty = liteuart_tx_empty, | |
| .set_mctrl = liteuart_set_mctrl, | |
| .get_mctrl = liteuart_get_mctrl, | |
| .stop_tx = liteuart_stop_tx, | |
| .start_tx = liteuart_start_tx, | |
| .stop_rx = liteuart_stop_rx, | |
| .startup = liteuart_startup, | |
| .shutdown = liteuart_shutdown, | |
| .set_termios = liteuart_set_termios, | |
| .type = liteuart_type, | |
| .config_port = liteuart_config_port, | |
| .verify_port = liteuart_verify_port, | |
| }; | |
| static int liteuart_probe(struct platform_device *pdev) | |
| { | |
| struct liteuart_port *uart; | |
| struct uart_port *port; | |
| struct xa_limit limit; | |
| int dev_id, ret; | |
| uart = devm_kzalloc(&pdev->dev, sizeof(struct liteuart_port), GFP_KERNEL); | |
| if (!uart) | |
| return -ENOMEM; | |
| port = &uart->port; | |
| /* get membase */ | |
| port->membase = devm_platform_get_and_ioremap_resource(pdev, 0, NULL); | |
| if (IS_ERR(port->membase)) | |
| return PTR_ERR(port->membase); | |
| ret = platform_get_irq_optional(pdev, 0); | |
| if (ret < 0 && ret != -ENXIO) | |
| return ret; | |
| if (ret > 0) | |
| port->irq = ret; | |
| /* look for aliases; auto-enumerate for free index if not found */ | |
| dev_id = of_alias_get_id(pdev->dev.of_node, "serial"); | |
| if (dev_id < 0) | |
| limit = XA_LIMIT(0, CONFIG_SERIAL_LITEUART_MAX_PORTS); | |
| else | |
| limit = XA_LIMIT(dev_id, dev_id); | |
| ret = xa_alloc(&liteuart_array, &dev_id, uart, limit, GFP_KERNEL); | |
| if (ret) | |
| return ret; | |
| /* values not from device tree */ | |
| port->dev = &pdev->dev; | |
| port->iotype = UPIO_MEM; | |
| port->flags = UPF_BOOT_AUTOCONF; | |
| port->ops = &liteuart_ops; | |
| port->fifosize = 16; | |
| port->type = PORT_UNKNOWN; | |
| port->line = dev_id; | |
| spin_lock_init(&port->lock); | |
| platform_set_drvdata(pdev, port); | |
| ret = uart_add_one_port(&liteuart_driver, &uart->port); | |
| if (ret) | |
| goto err_erase_id; | |
| return 0; | |
| err_erase_id: | |
| xa_erase(&liteuart_array, dev_id); | |
| return ret; | |
| } | |
| static void liteuart_remove(struct platform_device *pdev) | |
| { | |
| struct uart_port *port = platform_get_drvdata(pdev); | |
| unsigned int line = port->line; | |
| uart_remove_one_port(&liteuart_driver, port); | |
| xa_erase(&liteuart_array, line); | |
| } | |
| static const struct of_device_id liteuart_of_match[] = { | |
| { .compatible = "litex,liteuart" }, | |
| {} | |
| }; | |
| MODULE_DEVICE_TABLE(of, liteuart_of_match); | |
| static struct platform_driver liteuart_platform_driver = { | |
| .probe = liteuart_probe, | |
| .remove = liteuart_remove, | |
| .driver = { | |
| .name = KBUILD_MODNAME, | |
| .of_match_table = liteuart_of_match, | |
| }, | |
| }; | |
| #ifdef CONFIG_SERIAL_LITEUART_CONSOLE | |
| static void liteuart_putchar(struct uart_port *port, unsigned char ch) | |
| { | |
| while (litex_read8(port->membase + OFF_TXFULL)) | |
| cpu_relax(); | |
| litex_write8(port->membase + OFF_RXTX, ch); | |
| } | |
| static void liteuart_console_write(struct console *co, const char *s, | |
| unsigned int count) | |
| { | |
| struct liteuart_port *uart; | |
| struct uart_port *port; | |
| unsigned long flags; | |
| uart = (struct liteuart_port *)xa_load(&liteuart_array, co->index); | |
| port = &uart->port; | |
| uart_port_lock_irqsave(port, &flags); | |
| uart_console_write(port, s, count, liteuart_putchar); | |
| uart_port_unlock_irqrestore(port, flags); | |
| } | |
| static int liteuart_console_setup(struct console *co, char *options) | |
| { | |
| struct liteuart_port *uart; | |
| struct uart_port *port; | |
| int baud = 115200; | |
| int bits = 8; | |
| int parity = 'n'; | |
| int flow = 'n'; | |
| uart = (struct liteuart_port *)xa_load(&liteuart_array, co->index); | |
| if (!uart) | |
| return -ENODEV; | |
| port = &uart->port; | |
| if (!port->membase) | |
| return -ENODEV; | |
| if (options) | |
| uart_parse_options(options, &baud, &parity, &bits, &flow); | |
| return uart_set_options(port, co, baud, parity, bits, flow); | |
| } | |
| static struct console liteuart_console = { | |
| .name = KBUILD_MODNAME, | |
| .write = liteuart_console_write, | |
| .device = uart_console_device, | |
| .setup = liteuart_console_setup, | |
| .flags = CON_PRINTBUFFER, | |
| .index = -1, | |
| .data = &liteuart_driver, | |
| }; | |
| static int __init liteuart_console_init(void) | |
| { | |
| register_console(&liteuart_console); | |
| return 0; | |
| } | |
| console_initcall(liteuart_console_init); | |
| static void early_liteuart_write(struct console *console, const char *s, | |
| unsigned int count) | |
| { | |
| struct earlycon_device *device = console->data; | |
| struct uart_port *port = &device->port; | |
| uart_console_write(port, s, count, liteuart_putchar); | |
| } | |
| static int __init early_liteuart_setup(struct earlycon_device *device, | |
| const char *options) | |
| { | |
| if (!device->port.membase) | |
| return -ENODEV; | |
| device->con->write = early_liteuart_write; | |
| return 0; | |
| } | |
| OF_EARLYCON_DECLARE(liteuart, "litex,liteuart", early_liteuart_setup); | |
| #endif /* CONFIG_SERIAL_LITEUART_CONSOLE */ | |
| static int __init liteuart_init(void) | |
| { | |
| int res; | |
| res = uart_register_driver(&liteuart_driver); | |
| if (res) | |
| return res; | |
| res = platform_driver_register(&liteuart_platform_driver); | |
| if (res) | |
| uart_unregister_driver(&liteuart_driver); | |
| return res; | |
| } | |
| static void __exit liteuart_exit(void) | |
| { | |
| platform_driver_unregister(&liteuart_platform_driver); | |
| uart_unregister_driver(&liteuart_driver); | |
| } | |
| module_init(liteuart_init); | |
| module_exit(liteuart_exit); | |
| MODULE_AUTHOR("Antmicro <www.antmicro.com>"); | |
| MODULE_DESCRIPTION("LiteUART serial driver"); | |
| MODULE_LICENSE("GPL v2"); | |
| MODULE_ALIAS("platform:liteuart"); |