|  | // SPDX-License-Identifier: GPL-2.0+ | 
|  | /* | 
|  | * Driver for Realtek RTS51xx USB card reader | 
|  | * | 
|  | * Copyright(c) 2009 Realtek Semiconductor Corp. All rights reserved. | 
|  | * | 
|  | * Author: | 
|  | *   wwang (wei_wang@realsil.com.cn) | 
|  | *   No. 450, Shenhu Road, Suzhou Industry Park, Suzhou, China | 
|  | */ | 
|  |  | 
|  | #include <linux/module.h> | 
|  | #include <linux/blkdev.h> | 
|  | #include <linux/kthread.h> | 
|  | #include <linux/sched.h> | 
|  | #include <linux/kernel.h> | 
|  |  | 
|  | #include <scsi/scsi.h> | 
|  | #include <scsi/scsi_cmnd.h> | 
|  | #include <scsi/scsi_device.h> | 
|  | #include <linux/cdrom.h> | 
|  |  | 
|  | #include <linux/usb.h> | 
|  | #include <linux/slab.h> | 
|  | #include <linux/usb_usual.h> | 
|  |  | 
|  | #include "usb.h" | 
|  | #include "transport.h" | 
|  | #include "protocol.h" | 
|  | #include "debug.h" | 
|  | #include "scsiglue.h" | 
|  |  | 
|  | #define DRV_NAME "ums-realtek" | 
|  |  | 
|  | MODULE_DESCRIPTION("Driver for Realtek USB Card Reader"); | 
|  | MODULE_AUTHOR("wwang <wei_wang@realsil.com.cn>"); | 
|  | MODULE_LICENSE("GPL"); | 
|  | MODULE_IMPORT_NS(USB_STORAGE); | 
|  |  | 
|  | static int auto_delink_en = 1; | 
|  | module_param(auto_delink_en, int, S_IRUGO | S_IWUSR); | 
|  | MODULE_PARM_DESC(auto_delink_en, "auto delink mode (0=firmware, 1=software [default])"); | 
|  |  | 
|  | #ifdef CONFIG_REALTEK_AUTOPM | 
|  | static int ss_en = 1; | 
|  | module_param(ss_en, int, S_IRUGO | S_IWUSR); | 
|  | MODULE_PARM_DESC(ss_en, "enable selective suspend"); | 
|  |  | 
|  | static int ss_delay = 50; | 
|  | module_param(ss_delay, int, S_IRUGO | S_IWUSR); | 
|  | MODULE_PARM_DESC(ss_delay, | 
|  | "seconds to delay before entering selective suspend"); | 
|  |  | 
|  | enum RTS51X_STAT { | 
|  | RTS51X_STAT_INIT, | 
|  | RTS51X_STAT_IDLE, | 
|  | RTS51X_STAT_RUN, | 
|  | RTS51X_STAT_SS | 
|  | }; | 
|  |  | 
|  | #define POLLING_INTERVAL	50 | 
|  |  | 
|  | #define rts51x_set_stat(chip, stat)	\ | 
|  | ((chip)->state = (enum RTS51X_STAT)(stat)) | 
|  | #define rts51x_get_stat(chip)		((chip)->state) | 
|  |  | 
|  | #define SET_LUN_READY(chip, lun)	((chip)->lun_ready |= ((u8)1 << (lun))) | 
|  | #define CLR_LUN_READY(chip, lun)	((chip)->lun_ready &= ~((u8)1 << (lun))) | 
|  | #define TST_LUN_READY(chip, lun)	((chip)->lun_ready & ((u8)1 << (lun))) | 
|  |  | 
|  | #endif | 
|  |  | 
|  | struct rts51x_status { | 
|  | u16 vid; | 
|  | u16 pid; | 
|  | u8 cur_lun; | 
|  | u8 card_type; | 
|  | u8 total_lun; | 
|  | u16 fw_ver; | 
|  | u8 phy_exist; | 
|  | u8 multi_flag; | 
|  | u8 multi_card; | 
|  | u8 log_exist; | 
|  | union { | 
|  | u8 detailed_type1; | 
|  | u8 detailed_type2; | 
|  | } detailed_type; | 
|  | u8 function[2]; | 
|  | }; | 
|  |  | 
|  | struct rts51x_chip { | 
|  | u16 vendor_id; | 
|  | u16 product_id; | 
|  | char max_lun; | 
|  |  | 
|  | struct rts51x_status *status; | 
|  | int status_len; | 
|  |  | 
|  | u32 flag; | 
|  | struct us_data *us; | 
|  |  | 
|  | #ifdef CONFIG_REALTEK_AUTOPM | 
|  | struct timer_list rts51x_suspend_timer; | 
|  | unsigned long timer_expires; | 
|  | int pwr_state; | 
|  | u8 lun_ready; | 
|  | enum RTS51X_STAT state; | 
|  | int support_auto_delink; | 
|  | #endif | 
|  | /* used to back up the protocol chosen in probe1 phase */ | 
|  | proto_cmnd proto_handler_backup; | 
|  | }; | 
|  |  | 
|  | /* flag definition */ | 
|  | #define FLIDX_AUTO_DELINK		0x01 | 
|  |  | 
|  | #define SCSI_LUN(srb)			((srb)->device->lun) | 
|  |  | 
|  | /* Bit Operation */ | 
|  | #define SET_BIT(data, idx)		((data) |= 1 << (idx)) | 
|  | #define CLR_BIT(data, idx)		((data) &= ~(1 << (idx))) | 
|  | #define CHK_BIT(data, idx)		((data) & (1 << (idx))) | 
|  |  | 
|  | #define SET_AUTO_DELINK(chip)		((chip)->flag |= FLIDX_AUTO_DELINK) | 
|  | #define CLR_AUTO_DELINK(chip)		((chip)->flag &= ~FLIDX_AUTO_DELINK) | 
|  | #define CHK_AUTO_DELINK(chip)		((chip)->flag & FLIDX_AUTO_DELINK) | 
|  |  | 
|  | #define RTS51X_GET_VID(chip)		((chip)->vendor_id) | 
|  | #define RTS51X_GET_PID(chip)		((chip)->product_id) | 
|  |  | 
|  | #define VENDOR_ID(chip)			((chip)->status[0].vid) | 
|  | #define PRODUCT_ID(chip)		((chip)->status[0].pid) | 
|  | #define FW_VERSION(chip)		((chip)->status[0].fw_ver) | 
|  | #define STATUS_LEN(chip)		((chip)->status_len) | 
|  |  | 
|  | #define STATUS_SUCCESS		0 | 
|  | #define STATUS_FAIL		1 | 
|  |  | 
|  | /* Check card reader function */ | 
|  | #define SUPPORT_DETAILED_TYPE1(chip)	\ | 
|  | CHK_BIT((chip)->status[0].function[0], 1) | 
|  | #define SUPPORT_OT(chip)		\ | 
|  | CHK_BIT((chip)->status[0].function[0], 2) | 
|  | #define SUPPORT_OC(chip)		\ | 
|  | CHK_BIT((chip)->status[0].function[0], 3) | 
|  | #define SUPPORT_AUTO_DELINK(chip)	\ | 
|  | CHK_BIT((chip)->status[0].function[0], 4) | 
|  | #define SUPPORT_SDIO(chip)		\ | 
|  | CHK_BIT((chip)->status[0].function[1], 0) | 
|  | #define SUPPORT_DETAILED_TYPE2(chip)	\ | 
|  | CHK_BIT((chip)->status[0].function[1], 1) | 
|  |  | 
|  | #define CHECK_PID(chip, pid)		(RTS51X_GET_PID(chip) == (pid)) | 
|  | #define CHECK_FW_VER(chip, fw_ver)	(FW_VERSION(chip) == (fw_ver)) | 
|  | #define CHECK_ID(chip, pid, fw_ver)	\ | 
|  | (CHECK_PID((chip), (pid)) && CHECK_FW_VER((chip), (fw_ver))) | 
|  |  | 
|  | static int init_realtek_cr(struct us_data *us); | 
|  |  | 
|  | /* | 
|  | * The table of devices | 
|  | */ | 
|  | #define UNUSUAL_DEV(id_vendor, id_product, bcdDeviceMin, bcdDeviceMax, \ | 
|  | vendorName, productName, useProtocol, useTransport, \ | 
|  | initFunction, flags) \ | 
|  | {\ | 
|  | USB_DEVICE_VER(id_vendor, id_product, bcdDeviceMin, bcdDeviceMax), \ | 
|  | .driver_info = (flags) \ | 
|  | } | 
|  |  | 
|  | static const struct usb_device_id realtek_cr_ids[] = { | 
|  | #	include "unusual_realtek.h" | 
|  | {}			/* Terminating entry */ | 
|  | }; | 
|  |  | 
|  | MODULE_DEVICE_TABLE(usb, realtek_cr_ids); | 
|  |  | 
|  | #undef UNUSUAL_DEV | 
|  |  | 
|  | /* | 
|  | * The flags table | 
|  | */ | 
|  | #define UNUSUAL_DEV(idVendor, idProduct, bcdDeviceMin, bcdDeviceMax, \ | 
|  | vendor_name, product_name, use_protocol, use_transport, \ | 
|  | init_function, Flags) \ | 
|  | { \ | 
|  | .vendorName = vendor_name,	\ | 
|  | .productName = product_name,	\ | 
|  | .useProtocol = use_protocol,	\ | 
|  | .useTransport = use_transport,	\ | 
|  | .initFunction = init_function,	\ | 
|  | } | 
|  |  | 
|  | static struct us_unusual_dev realtek_cr_unusual_dev_list[] = { | 
|  | #	include "unusual_realtek.h" | 
|  | {}			/* Terminating entry */ | 
|  | }; | 
|  |  | 
|  | #undef UNUSUAL_DEV | 
|  |  | 
|  | static int rts51x_bulk_transport(struct us_data *us, u8 lun, | 
|  | u8 *cmd, int cmd_len, u8 *buf, int buf_len, | 
|  | enum dma_data_direction dir, int *act_len) | 
|  | { | 
|  | struct bulk_cb_wrap *bcb = (struct bulk_cb_wrap *)us->iobuf; | 
|  | struct bulk_cs_wrap *bcs = (struct bulk_cs_wrap *)us->iobuf; | 
|  | int result; | 
|  | unsigned int residue; | 
|  | unsigned int cswlen; | 
|  | unsigned int cbwlen = US_BULK_CB_WRAP_LEN; | 
|  |  | 
|  | /* set up the command wrapper */ | 
|  | bcb->Signature = cpu_to_le32(US_BULK_CB_SIGN); | 
|  | bcb->DataTransferLength = cpu_to_le32(buf_len); | 
|  | bcb->Flags = (dir == DMA_FROM_DEVICE) ? US_BULK_FLAG_IN : 0; | 
|  | bcb->Tag = ++us->tag; | 
|  | bcb->Lun = lun; | 
|  | bcb->Length = cmd_len; | 
|  |  | 
|  | /* copy the command payload */ | 
|  | memset(bcb->CDB, 0, sizeof(bcb->CDB)); | 
|  | memcpy(bcb->CDB, cmd, bcb->Length); | 
|  |  | 
|  | /* send it to out endpoint */ | 
|  | result = usb_stor_bulk_transfer_buf(us, us->send_bulk_pipe, | 
|  | bcb, cbwlen, NULL); | 
|  | if (result != USB_STOR_XFER_GOOD) | 
|  | return USB_STOR_TRANSPORT_ERROR; | 
|  |  | 
|  | /* DATA STAGE */ | 
|  | /* send/receive data payload, if there is any */ | 
|  |  | 
|  | if (buf && buf_len) { | 
|  | unsigned int pipe = (dir == DMA_FROM_DEVICE) ? | 
|  | us->recv_bulk_pipe : us->send_bulk_pipe; | 
|  | result = usb_stor_bulk_transfer_buf(us, pipe, | 
|  | buf, buf_len, NULL); | 
|  | if (result == USB_STOR_XFER_ERROR) | 
|  | return USB_STOR_TRANSPORT_ERROR; | 
|  | } | 
|  |  | 
|  | /* get CSW for device status */ | 
|  | result = usb_stor_bulk_transfer_buf(us, us->recv_bulk_pipe, | 
|  | bcs, US_BULK_CS_WRAP_LEN, &cswlen); | 
|  | if (result != USB_STOR_XFER_GOOD) | 
|  | return USB_STOR_TRANSPORT_ERROR; | 
|  |  | 
|  | /* check bulk status */ | 
|  | if (bcs->Signature != cpu_to_le32(US_BULK_CS_SIGN)) { | 
|  | usb_stor_dbg(us, "Signature mismatch: got %08X, expecting %08X\n", | 
|  | le32_to_cpu(bcs->Signature), US_BULK_CS_SIGN); | 
|  | return USB_STOR_TRANSPORT_ERROR; | 
|  | } | 
|  |  | 
|  | residue = le32_to_cpu(bcs->Residue); | 
|  | if (bcs->Tag != us->tag) | 
|  | return USB_STOR_TRANSPORT_ERROR; | 
|  |  | 
|  | /* | 
|  | * try to compute the actual residue, based on how much data | 
|  | * was really transferred and what the device tells us | 
|  | */ | 
|  | if (residue) | 
|  | residue = residue < buf_len ? residue : buf_len; | 
|  |  | 
|  | if (act_len) | 
|  | *act_len = buf_len - residue; | 
|  |  | 
|  | /* based on the status code, we report good or bad */ | 
|  | switch (bcs->Status) { | 
|  | case US_BULK_STAT_OK: | 
|  | /* command good -- note that data could be short */ | 
|  | return USB_STOR_TRANSPORT_GOOD; | 
|  |  | 
|  | case US_BULK_STAT_FAIL: | 
|  | /* command failed */ | 
|  | return USB_STOR_TRANSPORT_FAILED; | 
|  |  | 
|  | case US_BULK_STAT_PHASE: | 
|  | /* | 
|  | * phase error -- note that a transport reset will be | 
|  | * invoked by the invoke_transport() function | 
|  | */ | 
|  | return USB_STOR_TRANSPORT_ERROR; | 
|  | } | 
|  |  | 
|  | /* we should never get here, but if we do, we're in trouble */ | 
|  | return USB_STOR_TRANSPORT_ERROR; | 
|  | } | 
|  |  | 
|  | static int rts51x_bulk_transport_special(struct us_data *us, u8 lun, | 
|  | u8 *cmd, int cmd_len, u8 *buf, int buf_len, | 
|  | enum dma_data_direction dir, int *act_len) | 
|  | { | 
|  | struct bulk_cb_wrap *bcb = (struct bulk_cb_wrap *) us->iobuf; | 
|  | struct bulk_cs_wrap *bcs = (struct bulk_cs_wrap *) us->iobuf; | 
|  | int result; | 
|  | unsigned int cswlen; | 
|  | unsigned int cbwlen = US_BULK_CB_WRAP_LEN; | 
|  |  | 
|  | /* set up the command wrapper */ | 
|  | bcb->Signature = cpu_to_le32(US_BULK_CB_SIGN); | 
|  | bcb->DataTransferLength = cpu_to_le32(buf_len); | 
|  | bcb->Flags = (dir == DMA_FROM_DEVICE) ? US_BULK_FLAG_IN : 0; | 
|  | bcb->Tag = ++us->tag; | 
|  | bcb->Lun = lun; | 
|  | bcb->Length = cmd_len; | 
|  |  | 
|  | /* copy the command payload */ | 
|  | memset(bcb->CDB, 0, sizeof(bcb->CDB)); | 
|  | memcpy(bcb->CDB, cmd, bcb->Length); | 
|  |  | 
|  | /* send it to out endpoint */ | 
|  | result = usb_stor_bulk_transfer_buf(us, us->send_bulk_pipe, | 
|  | bcb, cbwlen, NULL); | 
|  | if (result != USB_STOR_XFER_GOOD) | 
|  | return USB_STOR_TRANSPORT_ERROR; | 
|  |  | 
|  | /* DATA STAGE */ | 
|  | /* send/receive data payload, if there is any */ | 
|  |  | 
|  | if (buf && buf_len) { | 
|  | unsigned int pipe = (dir == DMA_FROM_DEVICE) ? | 
|  | us->recv_bulk_pipe : us->send_bulk_pipe; | 
|  | result = usb_stor_bulk_transfer_buf(us, pipe, | 
|  | buf, buf_len, NULL); | 
|  | if (result == USB_STOR_XFER_ERROR) | 
|  | return USB_STOR_TRANSPORT_ERROR; | 
|  | } | 
|  |  | 
|  | /* get CSW for device status */ | 
|  | result = usb_bulk_msg(us->pusb_dev, us->recv_bulk_pipe, bcs, | 
|  | US_BULK_CS_WRAP_LEN, &cswlen, 250); | 
|  | return result; | 
|  | } | 
|  |  | 
|  | /* Determine what the maximum LUN supported is */ | 
|  | static int rts51x_get_max_lun(struct us_data *us) | 
|  | { | 
|  | int result; | 
|  |  | 
|  | /* issue the command */ | 
|  | us->iobuf[0] = 0; | 
|  | result = usb_stor_control_msg(us, us->recv_ctrl_pipe, | 
|  | US_BULK_GET_MAX_LUN, | 
|  | USB_DIR_IN | USB_TYPE_CLASS | | 
|  | USB_RECIP_INTERFACE, | 
|  | 0, us->ifnum, us->iobuf, 1, 10 * HZ); | 
|  |  | 
|  | usb_stor_dbg(us, "GetMaxLUN command result is %d, data is %d\n", | 
|  | result, us->iobuf[0]); | 
|  |  | 
|  | /* if we have a successful request, return the result */ | 
|  | if (result > 0) | 
|  | return us->iobuf[0]; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int rts51x_read_mem(struct us_data *us, u16 addr, u8 *data, u16 len) | 
|  | { | 
|  | int retval; | 
|  | u8 cmnd[12] = { 0 }; | 
|  | u8 *buf; | 
|  |  | 
|  | buf = kmalloc(len, GFP_NOIO); | 
|  | if (buf == NULL) | 
|  | return -ENOMEM; | 
|  |  | 
|  | usb_stor_dbg(us, "addr = 0x%x, len = %d\n", addr, len); | 
|  |  | 
|  | cmnd[0] = 0xF0; | 
|  | cmnd[1] = 0x0D; | 
|  | cmnd[2] = (u8) (addr >> 8); | 
|  | cmnd[3] = (u8) addr; | 
|  | cmnd[4] = (u8) (len >> 8); | 
|  | cmnd[5] = (u8) len; | 
|  |  | 
|  | retval = rts51x_bulk_transport(us, 0, cmnd, 12, | 
|  | buf, len, DMA_FROM_DEVICE, NULL); | 
|  | if (retval != USB_STOR_TRANSPORT_GOOD) { | 
|  | kfree(buf); | 
|  | return -EIO; | 
|  | } | 
|  |  | 
|  | memcpy(data, buf, len); | 
|  | kfree(buf); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int rts51x_write_mem(struct us_data *us, u16 addr, u8 *data, u16 len) | 
|  | { | 
|  | int retval; | 
|  | u8 cmnd[12] = { 0 }; | 
|  | u8 *buf; | 
|  |  | 
|  | buf = kmemdup(data, len, GFP_NOIO); | 
|  | if (buf == NULL) | 
|  | return USB_STOR_TRANSPORT_ERROR; | 
|  |  | 
|  | usb_stor_dbg(us, "addr = 0x%x, len = %d\n", addr, len); | 
|  |  | 
|  | cmnd[0] = 0xF0; | 
|  | cmnd[1] = 0x0E; | 
|  | cmnd[2] = (u8) (addr >> 8); | 
|  | cmnd[3] = (u8) addr; | 
|  | cmnd[4] = (u8) (len >> 8); | 
|  | cmnd[5] = (u8) len; | 
|  |  | 
|  | retval = rts51x_bulk_transport(us, 0, cmnd, 12, | 
|  | buf, len, DMA_TO_DEVICE, NULL); | 
|  | kfree(buf); | 
|  | if (retval != USB_STOR_TRANSPORT_GOOD) | 
|  | return -EIO; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int rts51x_read_status(struct us_data *us, | 
|  | u8 lun, u8 *status, int len, int *actlen) | 
|  | { | 
|  | int retval; | 
|  | u8 cmnd[12] = { 0 }; | 
|  | u8 *buf; | 
|  |  | 
|  | buf = kmalloc(len, GFP_NOIO); | 
|  | if (buf == NULL) | 
|  | return USB_STOR_TRANSPORT_ERROR; | 
|  |  | 
|  | usb_stor_dbg(us, "lun = %d\n", lun); | 
|  |  | 
|  | cmnd[0] = 0xF0; | 
|  | cmnd[1] = 0x09; | 
|  |  | 
|  | retval = rts51x_bulk_transport(us, lun, cmnd, 12, | 
|  | buf, len, DMA_FROM_DEVICE, actlen); | 
|  | if (retval != USB_STOR_TRANSPORT_GOOD) { | 
|  | kfree(buf); | 
|  | return -EIO; | 
|  | } | 
|  |  | 
|  | memcpy(status, buf, len); | 
|  | kfree(buf); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int rts51x_check_status(struct us_data *us, u8 lun) | 
|  | { | 
|  | struct rts51x_chip *chip = (struct rts51x_chip *)(us->extra); | 
|  | int retval; | 
|  | u8 buf[16]; | 
|  |  | 
|  | retval = rts51x_read_status(us, lun, buf, 16, &(chip->status_len)); | 
|  | if (retval != STATUS_SUCCESS) | 
|  | return -EIO; | 
|  |  | 
|  | usb_stor_dbg(us, "chip->status_len = %d\n", chip->status_len); | 
|  |  | 
|  | chip->status[lun].vid = ((u16) buf[0] << 8) | buf[1]; | 
|  | chip->status[lun].pid = ((u16) buf[2] << 8) | buf[3]; | 
|  | chip->status[lun].cur_lun = buf[4]; | 
|  | chip->status[lun].card_type = buf[5]; | 
|  | chip->status[lun].total_lun = buf[6]; | 
|  | chip->status[lun].fw_ver = ((u16) buf[7] << 8) | buf[8]; | 
|  | chip->status[lun].phy_exist = buf[9]; | 
|  | chip->status[lun].multi_flag = buf[10]; | 
|  | chip->status[lun].multi_card = buf[11]; | 
|  | chip->status[lun].log_exist = buf[12]; | 
|  | if (chip->status_len == 16) { | 
|  | chip->status[lun].detailed_type.detailed_type1 = buf[13]; | 
|  | chip->status[lun].function[0] = buf[14]; | 
|  | chip->status[lun].function[1] = buf[15]; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int enable_oscillator(struct us_data *us) | 
|  | { | 
|  | int retval; | 
|  | u8 value; | 
|  |  | 
|  | retval = rts51x_read_mem(us, 0xFE77, &value, 1); | 
|  | if (retval < 0) | 
|  | return -EIO; | 
|  |  | 
|  | value |= 0x04; | 
|  | retval = rts51x_write_mem(us, 0xFE77, &value, 1); | 
|  | if (retval < 0) | 
|  | return -EIO; | 
|  |  | 
|  | retval = rts51x_read_mem(us, 0xFE77, &value, 1); | 
|  | if (retval < 0) | 
|  | return -EIO; | 
|  |  | 
|  | if (!(value & 0x04)) | 
|  | return -EIO; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int __do_config_autodelink(struct us_data *us, u8 *data, u16 len) | 
|  | { | 
|  | int retval; | 
|  | u8 cmnd[12] = {0}; | 
|  | u8 *buf; | 
|  |  | 
|  | usb_stor_dbg(us, "addr = 0xfe47, len = %d\n", len); | 
|  |  | 
|  | buf = kmemdup(data, len, GFP_NOIO); | 
|  | if (!buf) | 
|  | return USB_STOR_TRANSPORT_ERROR; | 
|  |  | 
|  | cmnd[0] = 0xF0; | 
|  | cmnd[1] = 0x0E; | 
|  | cmnd[2] = 0xfe; | 
|  | cmnd[3] = 0x47; | 
|  | cmnd[4] = (u8)(len >> 8); | 
|  | cmnd[5] = (u8)len; | 
|  |  | 
|  | retval = rts51x_bulk_transport_special(us, 0, cmnd, 12, buf, len, DMA_TO_DEVICE, NULL); | 
|  | kfree(buf); | 
|  | if (retval != USB_STOR_TRANSPORT_GOOD) { | 
|  | return -EIO; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int do_config_autodelink(struct us_data *us, int enable, int force) | 
|  | { | 
|  | int retval; | 
|  | u8 value; | 
|  |  | 
|  | retval = rts51x_read_mem(us, 0xFE47, &value, 1); | 
|  | if (retval < 0) | 
|  | return -EIO; | 
|  |  | 
|  | if (enable) { | 
|  | if (force) | 
|  | value |= 0x03; | 
|  | else | 
|  | value |= 0x01; | 
|  | } else { | 
|  | value &= ~0x03; | 
|  | } | 
|  |  | 
|  | usb_stor_dbg(us, "set 0xfe47 to 0x%x\n", value); | 
|  |  | 
|  | /* retval = rts51x_write_mem(us, 0xFE47, &value, 1); */ | 
|  | retval = __do_config_autodelink(us, &value, 1); | 
|  | if (retval < 0) | 
|  | return -EIO; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int config_autodelink_after_power_on(struct us_data *us) | 
|  | { | 
|  | struct rts51x_chip *chip = (struct rts51x_chip *)(us->extra); | 
|  | int retval; | 
|  | u8 value; | 
|  |  | 
|  | if (!CHK_AUTO_DELINK(chip)) | 
|  | return 0; | 
|  |  | 
|  | retval = rts51x_read_mem(us, 0xFE47, &value, 1); | 
|  | if (retval < 0) | 
|  | return -EIO; | 
|  |  | 
|  | if (auto_delink_en) { | 
|  | CLR_BIT(value, 0); | 
|  | CLR_BIT(value, 1); | 
|  | SET_BIT(value, 2); | 
|  |  | 
|  | if (CHECK_ID(chip, 0x0138, 0x3882)) | 
|  | CLR_BIT(value, 2); | 
|  |  | 
|  | SET_BIT(value, 7); | 
|  |  | 
|  | /* retval = rts51x_write_mem(us, 0xFE47, &value, 1); */ | 
|  | retval = __do_config_autodelink(us, &value, 1); | 
|  | if (retval < 0) | 
|  | return -EIO; | 
|  |  | 
|  | retval = enable_oscillator(us); | 
|  | if (retval == 0) | 
|  | (void)do_config_autodelink(us, 1, 0); | 
|  | } else { | 
|  | /* Autodelink controlled by firmware */ | 
|  |  | 
|  | SET_BIT(value, 2); | 
|  |  | 
|  | if (CHECK_ID(chip, 0x0138, 0x3882)) | 
|  | CLR_BIT(value, 2); | 
|  |  | 
|  | if (CHECK_ID(chip, 0x0159, 0x5889) || | 
|  | CHECK_ID(chip, 0x0138, 0x3880)) { | 
|  | CLR_BIT(value, 0); | 
|  | CLR_BIT(value, 7); | 
|  | } | 
|  |  | 
|  | /* retval = rts51x_write_mem(us, 0xFE47, &value, 1); */ | 
|  | retval = __do_config_autodelink(us, &value, 1); | 
|  | if (retval < 0) | 
|  | return -EIO; | 
|  |  | 
|  | if (CHECK_ID(chip, 0x0159, 0x5888)) { | 
|  | value = 0xFF; | 
|  | retval = rts51x_write_mem(us, 0xFE79, &value, 1); | 
|  | if (retval < 0) | 
|  | return -EIO; | 
|  |  | 
|  | value = 0x01; | 
|  | retval = rts51x_write_mem(us, 0x48, &value, 1); | 
|  | if (retval < 0) | 
|  | return -EIO; | 
|  | } | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | #ifdef CONFIG_PM | 
|  | static int config_autodelink_before_power_down(struct us_data *us) | 
|  | { | 
|  | struct rts51x_chip *chip = (struct rts51x_chip *)(us->extra); | 
|  | int retval; | 
|  | u8 value; | 
|  |  | 
|  | if (!CHK_AUTO_DELINK(chip)) | 
|  | return 0; | 
|  |  | 
|  | if (auto_delink_en) { | 
|  | retval = rts51x_read_mem(us, 0xFE77, &value, 1); | 
|  | if (retval < 0) | 
|  | return -EIO; | 
|  |  | 
|  | SET_BIT(value, 2); | 
|  | retval = rts51x_write_mem(us, 0xFE77, &value, 1); | 
|  | if (retval < 0) | 
|  | return -EIO; | 
|  |  | 
|  | if (CHECK_ID(chip, 0x0159, 0x5888)) { | 
|  | value = 0x01; | 
|  | retval = rts51x_write_mem(us, 0x48, &value, 1); | 
|  | if (retval < 0) | 
|  | return -EIO; | 
|  | } | 
|  |  | 
|  | retval = rts51x_read_mem(us, 0xFE47, &value, 1); | 
|  | if (retval < 0) | 
|  | return -EIO; | 
|  |  | 
|  | SET_BIT(value, 0); | 
|  | if (CHECK_ID(chip, 0x0138, 0x3882)) | 
|  | SET_BIT(value, 2); | 
|  | retval = rts51x_write_mem(us, 0xFE77, &value, 1); | 
|  | if (retval < 0) | 
|  | return -EIO; | 
|  | } else { | 
|  | if (CHECK_ID(chip, 0x0159, 0x5889) || | 
|  | CHECK_ID(chip, 0x0138, 0x3880) || | 
|  | CHECK_ID(chip, 0x0138, 0x3882)) { | 
|  | retval = rts51x_read_mem(us, 0xFE47, &value, 1); | 
|  | if (retval < 0) | 
|  | return -EIO; | 
|  |  | 
|  | if (CHECK_ID(chip, 0x0159, 0x5889) || | 
|  | CHECK_ID(chip, 0x0138, 0x3880)) { | 
|  | SET_BIT(value, 0); | 
|  | SET_BIT(value, 7); | 
|  | } | 
|  |  | 
|  | if (CHECK_ID(chip, 0x0138, 0x3882)) | 
|  | SET_BIT(value, 2); | 
|  |  | 
|  | /* retval = rts51x_write_mem(us, 0xFE47, &value, 1); */ | 
|  | retval = __do_config_autodelink(us, &value, 1); | 
|  | if (retval < 0) | 
|  | return -EIO; | 
|  | } | 
|  |  | 
|  | if (CHECK_ID(chip, 0x0159, 0x5888)) { | 
|  | value = 0x01; | 
|  | retval = rts51x_write_mem(us, 0x48, &value, 1); | 
|  | if (retval < 0) | 
|  | return -EIO; | 
|  | } | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void fw5895_init(struct us_data *us) | 
|  | { | 
|  | struct rts51x_chip *chip = (struct rts51x_chip *)(us->extra); | 
|  | int retval; | 
|  | u8 val; | 
|  |  | 
|  | if ((PRODUCT_ID(chip) != 0x0158) || (FW_VERSION(chip) != 0x5895)) { | 
|  | usb_stor_dbg(us, "Not the specified device, return immediately!\n"); | 
|  | } else { | 
|  | retval = rts51x_read_mem(us, 0xFD6F, &val, 1); | 
|  | if (retval == STATUS_SUCCESS && (val & 0x1F) == 0) { | 
|  | val = 0x1F; | 
|  | retval = rts51x_write_mem(us, 0xFD70, &val, 1); | 
|  | if (retval != STATUS_SUCCESS) | 
|  | usb_stor_dbg(us, "Write memory fail\n"); | 
|  | } else { | 
|  | usb_stor_dbg(us, "Read memory fail, OR (val & 0x1F) != 0\n"); | 
|  | } | 
|  | } | 
|  | } | 
|  | #endif | 
|  |  | 
|  | #ifdef CONFIG_REALTEK_AUTOPM | 
|  | static void fw5895_set_mmc_wp(struct us_data *us) | 
|  | { | 
|  | struct rts51x_chip *chip = (struct rts51x_chip *)(us->extra); | 
|  | int retval; | 
|  | u8 buf[13]; | 
|  |  | 
|  | if ((PRODUCT_ID(chip) != 0x0158) || (FW_VERSION(chip) != 0x5895)) { | 
|  | usb_stor_dbg(us, "Not the specified device, return immediately!\n"); | 
|  | } else { | 
|  | retval = rts51x_read_mem(us, 0xFD6F, buf, 1); | 
|  | if (retval == STATUS_SUCCESS && (buf[0] & 0x24) == 0x24) { | 
|  | /* SD Exist and SD WP */ | 
|  | retval = rts51x_read_mem(us, 0xD04E, buf, 1); | 
|  | if (retval == STATUS_SUCCESS) { | 
|  | buf[0] |= 0x04; | 
|  | retval = rts51x_write_mem(us, 0xFD70, buf, 1); | 
|  | if (retval != STATUS_SUCCESS) | 
|  | usb_stor_dbg(us, "Write memory fail\n"); | 
|  | } else { | 
|  | usb_stor_dbg(us, "Read memory fail\n"); | 
|  | } | 
|  | } else { | 
|  | usb_stor_dbg(us, "Read memory fail, OR (buf[0]&0x24)!=0x24\n"); | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | static void rts51x_modi_suspend_timer(struct rts51x_chip *chip) | 
|  | { | 
|  | struct us_data *us = chip->us; | 
|  |  | 
|  | usb_stor_dbg(us, "state:%d\n", rts51x_get_stat(chip)); | 
|  |  | 
|  | chip->timer_expires = jiffies + msecs_to_jiffies(1000*ss_delay); | 
|  | mod_timer(&chip->rts51x_suspend_timer, chip->timer_expires); | 
|  | } | 
|  |  | 
|  | static void rts51x_suspend_timer_fn(struct timer_list *t) | 
|  | { | 
|  | struct rts51x_chip *chip = from_timer(chip, t, rts51x_suspend_timer); | 
|  | struct us_data *us = chip->us; | 
|  |  | 
|  | switch (rts51x_get_stat(chip)) { | 
|  | case RTS51X_STAT_INIT: | 
|  | case RTS51X_STAT_RUN: | 
|  | rts51x_modi_suspend_timer(chip); | 
|  | break; | 
|  | case RTS51X_STAT_IDLE: | 
|  | case RTS51X_STAT_SS: | 
|  | usb_stor_dbg(us, "RTS51X_STAT_SS, power.usage:%d\n", | 
|  | atomic_read(&us->pusb_intf->dev.power.usage_count)); | 
|  |  | 
|  | if (atomic_read(&us->pusb_intf->dev.power.usage_count) > 0) { | 
|  | usb_stor_dbg(us, "Ready to enter SS state\n"); | 
|  | rts51x_set_stat(chip, RTS51X_STAT_SS); | 
|  | /* ignore mass storage interface's children */ | 
|  | pm_suspend_ignore_children(&us->pusb_intf->dev, true); | 
|  | usb_autopm_put_interface_async(us->pusb_intf); | 
|  | usb_stor_dbg(us, "RTS51X_STAT_SS 01, power.usage:%d\n", | 
|  | atomic_read(&us->pusb_intf->dev.power.usage_count)); | 
|  | } | 
|  | break; | 
|  | default: | 
|  | usb_stor_dbg(us, "Unknown state !!!\n"); | 
|  | break; | 
|  | } | 
|  | } | 
|  |  | 
|  | static inline int working_scsi(struct scsi_cmnd *srb) | 
|  | { | 
|  | if ((srb->cmnd[0] == TEST_UNIT_READY) || | 
|  | (srb->cmnd[0] == ALLOW_MEDIUM_REMOVAL)) { | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | return 1; | 
|  | } | 
|  |  | 
|  | static void rts51x_invoke_transport(struct scsi_cmnd *srb, struct us_data *us) | 
|  | { | 
|  | struct rts51x_chip *chip = (struct rts51x_chip *)(us->extra); | 
|  | static int card_first_show = 1; | 
|  | static u8 media_not_present[] = { 0x70, 0, 0x02, 0, 0, 0, 0, | 
|  | 10, 0, 0, 0, 0, 0x3A, 0, 0, 0, 0, 0 | 
|  | }; | 
|  | static u8 invalid_cmd_field[] = { 0x70, 0, 0x05, 0, 0, 0, 0, | 
|  | 10, 0, 0, 0, 0, 0x24, 0, 0, 0, 0, 0 | 
|  | }; | 
|  | int ret; | 
|  |  | 
|  | if (working_scsi(srb)) { | 
|  | usb_stor_dbg(us, "working scsi, power.usage:%d\n", | 
|  | atomic_read(&us->pusb_intf->dev.power.usage_count)); | 
|  |  | 
|  | if (atomic_read(&us->pusb_intf->dev.power.usage_count) <= 0) { | 
|  | ret = usb_autopm_get_interface(us->pusb_intf); | 
|  | usb_stor_dbg(us, "working scsi, ret=%d\n", ret); | 
|  | } | 
|  | if (rts51x_get_stat(chip) != RTS51X_STAT_RUN) | 
|  | rts51x_set_stat(chip, RTS51X_STAT_RUN); | 
|  | chip->proto_handler_backup(srb, us); | 
|  | } else { | 
|  | if (rts51x_get_stat(chip) == RTS51X_STAT_SS) { | 
|  | usb_stor_dbg(us, "NOT working scsi\n"); | 
|  | if ((srb->cmnd[0] == TEST_UNIT_READY) && | 
|  | (chip->pwr_state == US_SUSPEND)) { | 
|  | if (TST_LUN_READY(chip, srb->device->lun)) { | 
|  | srb->result = SAM_STAT_GOOD; | 
|  | } else { | 
|  | srb->result = SAM_STAT_CHECK_CONDITION; | 
|  | memcpy(srb->sense_buffer, | 
|  | media_not_present, | 
|  | US_SENSE_SIZE); | 
|  | } | 
|  | usb_stor_dbg(us, "TEST_UNIT_READY\n"); | 
|  | goto out; | 
|  | } | 
|  | if (srb->cmnd[0] == ALLOW_MEDIUM_REMOVAL) { | 
|  | int prevent = srb->cmnd[4] & 0x1; | 
|  | if (prevent) { | 
|  | srb->result = SAM_STAT_CHECK_CONDITION; | 
|  | memcpy(srb->sense_buffer, | 
|  | invalid_cmd_field, | 
|  | US_SENSE_SIZE); | 
|  | } else { | 
|  | srb->result = SAM_STAT_GOOD; | 
|  | } | 
|  | usb_stor_dbg(us, "ALLOW_MEDIUM_REMOVAL\n"); | 
|  | goto out; | 
|  | } | 
|  | } else { | 
|  | usb_stor_dbg(us, "NOT working scsi, not SS\n"); | 
|  | chip->proto_handler_backup(srb, us); | 
|  | /* Check whether card is plugged in */ | 
|  | if (srb->cmnd[0] == TEST_UNIT_READY) { | 
|  | if (srb->result == SAM_STAT_GOOD) { | 
|  | SET_LUN_READY(chip, srb->device->lun); | 
|  | if (card_first_show) { | 
|  | card_first_show = 0; | 
|  | fw5895_set_mmc_wp(us); | 
|  | } | 
|  | } else { | 
|  | CLR_LUN_READY(chip, srb->device->lun); | 
|  | card_first_show = 1; | 
|  | } | 
|  | } | 
|  | if (rts51x_get_stat(chip) != RTS51X_STAT_IDLE) | 
|  | rts51x_set_stat(chip, RTS51X_STAT_IDLE); | 
|  | } | 
|  | } | 
|  | out: | 
|  | usb_stor_dbg(us, "state:%d\n", rts51x_get_stat(chip)); | 
|  | if (rts51x_get_stat(chip) == RTS51X_STAT_RUN) | 
|  | rts51x_modi_suspend_timer(chip); | 
|  | } | 
|  |  | 
|  | static int realtek_cr_autosuspend_setup(struct us_data *us) | 
|  | { | 
|  | struct rts51x_chip *chip; | 
|  | struct rts51x_status *status = NULL; | 
|  | u8 buf[16]; | 
|  | int retval; | 
|  |  | 
|  | chip = (struct rts51x_chip *)us->extra; | 
|  | chip->support_auto_delink = 0; | 
|  | chip->pwr_state = US_RESUME; | 
|  | chip->lun_ready = 0; | 
|  | rts51x_set_stat(chip, RTS51X_STAT_INIT); | 
|  |  | 
|  | retval = rts51x_read_status(us, 0, buf, 16, &(chip->status_len)); | 
|  | if (retval != STATUS_SUCCESS) { | 
|  | usb_stor_dbg(us, "Read status fail\n"); | 
|  | return -EIO; | 
|  | } | 
|  | status = chip->status; | 
|  | status->vid = ((u16) buf[0] << 8) | buf[1]; | 
|  | status->pid = ((u16) buf[2] << 8) | buf[3]; | 
|  | status->cur_lun = buf[4]; | 
|  | status->card_type = buf[5]; | 
|  | status->total_lun = buf[6]; | 
|  | status->fw_ver = ((u16) buf[7] << 8) | buf[8]; | 
|  | status->phy_exist = buf[9]; | 
|  | status->multi_flag = buf[10]; | 
|  | status->multi_card = buf[11]; | 
|  | status->log_exist = buf[12]; | 
|  | if (chip->status_len == 16) { | 
|  | status->detailed_type.detailed_type1 = buf[13]; | 
|  | status->function[0] = buf[14]; | 
|  | status->function[1] = buf[15]; | 
|  | } | 
|  |  | 
|  | /* back up the proto_handler in us->extra */ | 
|  | chip = (struct rts51x_chip *)(us->extra); | 
|  | chip->proto_handler_backup = us->proto_handler; | 
|  | /* Set the autosuspend_delay to 0 */ | 
|  | pm_runtime_set_autosuspend_delay(&us->pusb_dev->dev, 0); | 
|  | /* override us->proto_handler setted in get_protocol() */ | 
|  | us->proto_handler = rts51x_invoke_transport; | 
|  |  | 
|  | chip->timer_expires = 0; | 
|  | timer_setup(&chip->rts51x_suspend_timer, rts51x_suspend_timer_fn, 0); | 
|  | fw5895_init(us); | 
|  |  | 
|  | /* enable autosuspend function of the usb device */ | 
|  | usb_enable_autosuspend(us->pusb_dev); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  | #endif | 
|  |  | 
|  | static void realtek_cr_destructor(void *extra) | 
|  | { | 
|  | struct rts51x_chip *chip = extra; | 
|  |  | 
|  | if (!chip) | 
|  | return; | 
|  |  | 
|  | #ifdef CONFIG_REALTEK_AUTOPM | 
|  | if (ss_en) { | 
|  | del_timer(&chip->rts51x_suspend_timer); | 
|  | chip->timer_expires = 0; | 
|  | } | 
|  | #endif | 
|  | kfree(chip->status); | 
|  | } | 
|  |  | 
|  | #ifdef CONFIG_PM | 
|  | static int realtek_cr_suspend(struct usb_interface *iface, pm_message_t message) | 
|  | { | 
|  | struct us_data *us = usb_get_intfdata(iface); | 
|  |  | 
|  | /* wait until no command is running */ | 
|  | mutex_lock(&us->dev_mutex); | 
|  |  | 
|  | config_autodelink_before_power_down(us); | 
|  |  | 
|  | mutex_unlock(&us->dev_mutex); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int realtek_cr_resume(struct usb_interface *iface) | 
|  | { | 
|  | struct us_data *us = usb_get_intfdata(iface); | 
|  |  | 
|  | fw5895_init(us); | 
|  | config_autodelink_after_power_on(us); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  | #else | 
|  | #define realtek_cr_suspend	NULL | 
|  | #define realtek_cr_resume	NULL | 
|  | #endif | 
|  |  | 
|  | static int init_realtek_cr(struct us_data *us) | 
|  | { | 
|  | struct rts51x_chip *chip; | 
|  | int size, i, retval; | 
|  |  | 
|  | chip = kzalloc(sizeof(struct rts51x_chip), GFP_KERNEL); | 
|  | if (!chip) | 
|  | return -ENOMEM; | 
|  |  | 
|  | us->extra = chip; | 
|  | us->extra_destructor = realtek_cr_destructor; | 
|  | us->max_lun = chip->max_lun = rts51x_get_max_lun(us); | 
|  | chip->us = us; | 
|  |  | 
|  | usb_stor_dbg(us, "chip->max_lun = %d\n", chip->max_lun); | 
|  |  | 
|  | size = (chip->max_lun + 1) * sizeof(struct rts51x_status); | 
|  | chip->status = kzalloc(size, GFP_KERNEL); | 
|  | if (!chip->status) | 
|  | goto INIT_FAIL; | 
|  |  | 
|  | for (i = 0; i <= (int)(chip->max_lun); i++) { | 
|  | retval = rts51x_check_status(us, (u8) i); | 
|  | if (retval < 0) | 
|  | goto INIT_FAIL; | 
|  | } | 
|  |  | 
|  | if (CHECK_PID(chip, 0x0138) || CHECK_PID(chip, 0x0158) || | 
|  | CHECK_PID(chip, 0x0159)) { | 
|  | if (CHECK_FW_VER(chip, 0x5888) || CHECK_FW_VER(chip, 0x5889) || | 
|  | CHECK_FW_VER(chip, 0x5901)) | 
|  | SET_AUTO_DELINK(chip); | 
|  | if (STATUS_LEN(chip) == 16) { | 
|  | if (SUPPORT_AUTO_DELINK(chip)) | 
|  | SET_AUTO_DELINK(chip); | 
|  | } | 
|  | } | 
|  | #ifdef CONFIG_REALTEK_AUTOPM | 
|  | if (ss_en) | 
|  | realtek_cr_autosuspend_setup(us); | 
|  | #endif | 
|  |  | 
|  | usb_stor_dbg(us, "chip->flag = 0x%x\n", chip->flag); | 
|  |  | 
|  | (void)config_autodelink_after_power_on(us); | 
|  |  | 
|  | return 0; | 
|  |  | 
|  | INIT_FAIL: | 
|  | if (us->extra) { | 
|  | kfree(chip->status); | 
|  | kfree(us->extra); | 
|  | us->extra = NULL; | 
|  | } | 
|  |  | 
|  | return -EIO; | 
|  | } | 
|  |  | 
|  | static struct scsi_host_template realtek_cr_host_template; | 
|  |  | 
|  | static int realtek_cr_probe(struct usb_interface *intf, | 
|  | const struct usb_device_id *id) | 
|  | { | 
|  | struct us_data *us; | 
|  | int result; | 
|  |  | 
|  | dev_dbg(&intf->dev, "Probe Realtek Card Reader!\n"); | 
|  |  | 
|  | result = usb_stor_probe1(&us, intf, id, | 
|  | (id - realtek_cr_ids) + | 
|  | realtek_cr_unusual_dev_list, | 
|  | &realtek_cr_host_template); | 
|  | if (result) | 
|  | return result; | 
|  |  | 
|  | result = usb_stor_probe2(us); | 
|  |  | 
|  | return result; | 
|  | } | 
|  |  | 
|  | static struct usb_driver realtek_cr_driver = { | 
|  | .name = DRV_NAME, | 
|  | .probe = realtek_cr_probe, | 
|  | .disconnect = usb_stor_disconnect, | 
|  | /* .suspend =      usb_stor_suspend, */ | 
|  | /* .resume =       usb_stor_resume, */ | 
|  | .reset_resume = usb_stor_reset_resume, | 
|  | .suspend = realtek_cr_suspend, | 
|  | .resume = realtek_cr_resume, | 
|  | .pre_reset = usb_stor_pre_reset, | 
|  | .post_reset = usb_stor_post_reset, | 
|  | .id_table = realtek_cr_ids, | 
|  | .soft_unbind = 1, | 
|  | .supports_autosuspend = 1, | 
|  | .no_dynamic_id = 1, | 
|  | }; | 
|  |  | 
|  | module_usb_stor_driver(realtek_cr_driver, realtek_cr_host_template, DRV_NAME); |