| /* SPDX-License-Identifier: GPL-2.0-only */ | |
| /* | |
| * IEEE 802.11 defines | |
| * | |
| * Copyright (c) 2001-2002, SSH Communications Security Corp and Jouni Malinen | |
| * <jkmaline@cc.hut.fi> | |
| * Copyright (c) 2002-2003, Jouni Malinen <jkmaline@cc.hut.fi> | |
| * Copyright (c) 2005, Devicescape Software, Inc. | |
| * Copyright (c) 2006, Michael Wu <flamingice@sourmilk.net> | |
| * Copyright (c) 2013 - 2014 Intel Mobile Communications GmbH | |
| * Copyright (c) 2016 - 2017 Intel Deutschland GmbH | |
| * Copyright (c) 2018 - 2020 Intel Corporation | |
| */ | |
| #ifndef LINUX_IEEE80211_H | |
| #define LINUX_IEEE80211_H | |
| #include <linux/types.h> | |
| #include <linux/if_ether.h> | |
| #include <linux/etherdevice.h> | |
| #include <asm/byteorder.h> | |
| #include <asm/unaligned.h> | |
| /* | |
| * DS bit usage | |
| * | |
| * TA = transmitter address | |
| * RA = receiver address | |
| * DA = destination address | |
| * SA = source address | |
| * | |
| * ToDS FromDS A1(RA) A2(TA) A3 A4 Use | |
| * ----------------------------------------------------------------- | |
| * 0 0 DA SA BSSID - IBSS/DLS | |
| * 0 1 DA BSSID SA - AP -> STA | |
| * 1 0 BSSID SA DA - AP <- STA | |
| * 1 1 RA TA DA SA unspecified (WDS) | |
| */ | |
| #define FCS_LEN 4 | |
| #define IEEE80211_FCTL_VERS 0x0003 | |
| #define IEEE80211_FCTL_FTYPE 0x000c | |
| #define IEEE80211_FCTL_STYPE 0x00f0 | |
| #define IEEE80211_FCTL_TODS 0x0100 | |
| #define IEEE80211_FCTL_FROMDS 0x0200 | |
| #define IEEE80211_FCTL_MOREFRAGS 0x0400 | |
| #define IEEE80211_FCTL_RETRY 0x0800 | |
| #define IEEE80211_FCTL_PM 0x1000 | |
| #define IEEE80211_FCTL_MOREDATA 0x2000 | |
| #define IEEE80211_FCTL_PROTECTED 0x4000 | |
| #define IEEE80211_FCTL_ORDER 0x8000 | |
| #define IEEE80211_FCTL_CTL_EXT 0x0f00 | |
| #define IEEE80211_SCTL_FRAG 0x000F | |
| #define IEEE80211_SCTL_SEQ 0xFFF0 | |
| #define IEEE80211_FTYPE_MGMT 0x0000 | |
| #define IEEE80211_FTYPE_CTL 0x0004 | |
| #define IEEE80211_FTYPE_DATA 0x0008 | |
| #define IEEE80211_FTYPE_EXT 0x000c | |
| /* management */ | |
| #define IEEE80211_STYPE_ASSOC_REQ 0x0000 | |
| #define IEEE80211_STYPE_ASSOC_RESP 0x0010 | |
| #define IEEE80211_STYPE_REASSOC_REQ 0x0020 | |
| #define IEEE80211_STYPE_REASSOC_RESP 0x0030 | |
| #define IEEE80211_STYPE_PROBE_REQ 0x0040 | |
| #define IEEE80211_STYPE_PROBE_RESP 0x0050 | |
| #define IEEE80211_STYPE_BEACON 0x0080 | |
| #define IEEE80211_STYPE_ATIM 0x0090 | |
| #define IEEE80211_STYPE_DISASSOC 0x00A0 | |
| #define IEEE80211_STYPE_AUTH 0x00B0 | |
| #define IEEE80211_STYPE_DEAUTH 0x00C0 | |
| #define IEEE80211_STYPE_ACTION 0x00D0 | |
| /* control */ | |
| #define IEEE80211_STYPE_CTL_EXT 0x0060 | |
| #define IEEE80211_STYPE_BACK_REQ 0x0080 | |
| #define IEEE80211_STYPE_BACK 0x0090 | |
| #define IEEE80211_STYPE_PSPOLL 0x00A0 | |
| #define IEEE80211_STYPE_RTS 0x00B0 | |
| #define IEEE80211_STYPE_CTS 0x00C0 | |
| #define IEEE80211_STYPE_ACK 0x00D0 | |
| #define IEEE80211_STYPE_CFEND 0x00E0 | |
| #define IEEE80211_STYPE_CFENDACK 0x00F0 | |
| /* data */ | |
| #define IEEE80211_STYPE_DATA 0x0000 | |
| #define IEEE80211_STYPE_DATA_CFACK 0x0010 | |
| #define IEEE80211_STYPE_DATA_CFPOLL 0x0020 | |
| #define IEEE80211_STYPE_DATA_CFACKPOLL 0x0030 | |
| #define IEEE80211_STYPE_NULLFUNC 0x0040 | |
| #define IEEE80211_STYPE_CFACK 0x0050 | |
| #define IEEE80211_STYPE_CFPOLL 0x0060 | |
| #define IEEE80211_STYPE_CFACKPOLL 0x0070 | |
| #define IEEE80211_STYPE_QOS_DATA 0x0080 | |
| #define IEEE80211_STYPE_QOS_DATA_CFACK 0x0090 | |
| #define IEEE80211_STYPE_QOS_DATA_CFPOLL 0x00A0 | |
| #define IEEE80211_STYPE_QOS_DATA_CFACKPOLL 0x00B0 | |
| #define IEEE80211_STYPE_QOS_NULLFUNC 0x00C0 | |
| #define IEEE80211_STYPE_QOS_CFACK 0x00D0 | |
| #define IEEE80211_STYPE_QOS_CFPOLL 0x00E0 | |
| #define IEEE80211_STYPE_QOS_CFACKPOLL 0x00F0 | |
| /* extension, added by 802.11ad */ | |
| #define IEEE80211_STYPE_DMG_BEACON 0x0000 | |
| #define IEEE80211_STYPE_S1G_BEACON 0x0010 | |
| /* bits unique to S1G beacon */ | |
| #define IEEE80211_S1G_BCN_NEXT_TBTT 0x100 | |
| /* see 802.11ah-2016 9.9 NDP CMAC frames */ | |
| #define IEEE80211_S1G_1MHZ_NDP_BITS 25 | |
| #define IEEE80211_S1G_1MHZ_NDP_BYTES 4 | |
| #define IEEE80211_S1G_2MHZ_NDP_BITS 37 | |
| #define IEEE80211_S1G_2MHZ_NDP_BYTES 5 | |
| #define IEEE80211_NDP_FTYPE_CTS 0 | |
| #define IEEE80211_NDP_FTYPE_CF_END 0 | |
| #define IEEE80211_NDP_FTYPE_PS_POLL 1 | |
| #define IEEE80211_NDP_FTYPE_ACK 2 | |
| #define IEEE80211_NDP_FTYPE_PS_POLL_ACK 3 | |
| #define IEEE80211_NDP_FTYPE_BA 4 | |
| #define IEEE80211_NDP_FTYPE_BF_REPORT_POLL 5 | |
| #define IEEE80211_NDP_FTYPE_PAGING 6 | |
| #define IEEE80211_NDP_FTYPE_PREQ 7 | |
| #define SM64(f, v) ((((u64)v) << f##_S) & f) | |
| /* NDP CMAC frame fields */ | |
| #define IEEE80211_NDP_FTYPE 0x0000000000000007 | |
| #define IEEE80211_NDP_FTYPE_S 0x0000000000000000 | |
| /* 1M Probe Request 11ah 9.9.3.1.1 */ | |
| #define IEEE80211_NDP_1M_PREQ_ANO 0x0000000000000008 | |
| #define IEEE80211_NDP_1M_PREQ_ANO_S 3 | |
| #define IEEE80211_NDP_1M_PREQ_CSSID 0x00000000000FFFF0 | |
| #define IEEE80211_NDP_1M_PREQ_CSSID_S 4 | |
| #define IEEE80211_NDP_1M_PREQ_RTYPE 0x0000000000100000 | |
| #define IEEE80211_NDP_1M_PREQ_RTYPE_S 20 | |
| #define IEEE80211_NDP_1M_PREQ_RSV 0x0000000001E00000 | |
| #define IEEE80211_NDP_1M_PREQ_RSV 0x0000000001E00000 | |
| /* 2M Probe Request 11ah 9.9.3.1.2 */ | |
| #define IEEE80211_NDP_2M_PREQ_ANO 0x0000000000000008 | |
| #define IEEE80211_NDP_2M_PREQ_ANO_S 3 | |
| #define IEEE80211_NDP_2M_PREQ_CSSID 0x0000000FFFFFFFF0 | |
| #define IEEE80211_NDP_2M_PREQ_CSSID_S 4 | |
| #define IEEE80211_NDP_2M_PREQ_RTYPE 0x0000001000000000 | |
| #define IEEE80211_NDP_2M_PREQ_RTYPE_S 36 | |
| #define IEEE80211_ANO_NETTYPE_WILD 15 | |
| /* bits unique to S1G beacon */ | |
| #define IEEE80211_S1G_BCN_NEXT_TBTT 0x100 | |
| /* control extension - for IEEE80211_FTYPE_CTL | IEEE80211_STYPE_CTL_EXT */ | |
| #define IEEE80211_CTL_EXT_POLL 0x2000 | |
| #define IEEE80211_CTL_EXT_SPR 0x3000 | |
| #define IEEE80211_CTL_EXT_GRANT 0x4000 | |
| #define IEEE80211_CTL_EXT_DMG_CTS 0x5000 | |
| #define IEEE80211_CTL_EXT_DMG_DTS 0x6000 | |
| #define IEEE80211_CTL_EXT_SSW 0x8000 | |
| #define IEEE80211_CTL_EXT_SSW_FBACK 0x9000 | |
| #define IEEE80211_CTL_EXT_SSW_ACK 0xa000 | |
| #define IEEE80211_SN_MASK ((IEEE80211_SCTL_SEQ) >> 4) | |
| #define IEEE80211_MAX_SN IEEE80211_SN_MASK | |
| #define IEEE80211_SN_MODULO (IEEE80211_MAX_SN + 1) | |
| /* PV1 Layout 11ah 9.8.3.1 */ | |
| #define IEEE80211_PV1_FCTL_VERS 0x0003 | |
| #define IEEE80211_PV1_FCTL_FTYPE 0x001c | |
| #define IEEE80211_PV1_FCTL_STYPE 0x00e0 | |
| #define IEEE80211_PV1_FCTL_TODS 0x0100 | |
| #define IEEE80211_PV1_FCTL_MOREFRAGS 0x0200 | |
| #define IEEE80211_PV1_FCTL_PM 0x0400 | |
| #define IEEE80211_PV1_FCTL_MOREDATA 0x0800 | |
| #define IEEE80211_PV1_FCTL_PROTECTED 0x1000 | |
| #define IEEE80211_PV1_FCTL_END_SP 0x2000 | |
| #define IEEE80211_PV1_FCTL_RELAYED 0x4000 | |
| #define IEEE80211_PV1_FCTL_ACK_POLICY 0x8000 | |
| #define IEEE80211_PV1_FCTL_CTL_EXT 0x0f00 | |
| static inline bool ieee80211_sn_less(u16 sn1, u16 sn2) | |
| { | |
| return ((sn1 - sn2) & IEEE80211_SN_MASK) > (IEEE80211_SN_MODULO >> 1); | |
| } | |
| static inline u16 ieee80211_sn_add(u16 sn1, u16 sn2) | |
| { | |
| return (sn1 + sn2) & IEEE80211_SN_MASK; | |
| } | |
| static inline u16 ieee80211_sn_inc(u16 sn) | |
| { | |
| return ieee80211_sn_add(sn, 1); | |
| } | |
| static inline u16 ieee80211_sn_sub(u16 sn1, u16 sn2) | |
| { | |
| return (sn1 - sn2) & IEEE80211_SN_MASK; | |
| } | |
| #define IEEE80211_SEQ_TO_SN(seq) (((seq) & IEEE80211_SCTL_SEQ) >> 4) | |
| #define IEEE80211_SN_TO_SEQ(ssn) (((ssn) << 4) & IEEE80211_SCTL_SEQ) | |
| /* miscellaneous IEEE 802.11 constants */ | |
| #define IEEE80211_MAX_FRAG_THRESHOLD 2352 | |
| #define IEEE80211_MAX_RTS_THRESHOLD 2353 | |
| #define IEEE80211_MAX_AID 2007 | |
| #define IEEE80211_MAX_AID_S1G 8191 | |
| #define IEEE80211_MAX_TIM_LEN 251 | |
| #define IEEE80211_MAX_MESH_PEERINGS 63 | |
| /* Maximum size for the MA-UNITDATA primitive, 802.11 standard section | |
| 6.2.1.1.2. | |
| 802.11e clarifies the figure in section 7.1.2. The frame body is | |
| up to 2304 octets long (maximum MSDU size) plus any crypt overhead. */ | |
| #define IEEE80211_MAX_DATA_LEN 2304 | |
| /* 802.11ad extends maximum MSDU size for DMG (freq > 40Ghz) networks | |
| * to 7920 bytes, see 8.2.3 General frame format | |
| */ | |
| #define IEEE80211_MAX_DATA_LEN_DMG 7920 | |
| /* 30 byte 4 addr hdr, 2 byte QoS, 2304 byte MSDU, 12 byte crypt, 4 byte FCS */ | |
| #define IEEE80211_MAX_FRAME_LEN 2352 | |
| /* Maximal size of an A-MSDU that can be transported in a HT BA session */ | |
| #define IEEE80211_MAX_MPDU_LEN_HT_BA 4095 | |
| /* Maximal size of an A-MSDU */ | |
| #define IEEE80211_MAX_MPDU_LEN_HT_3839 3839 | |
| #define IEEE80211_MAX_MPDU_LEN_HT_7935 7935 | |
| #define IEEE80211_MAX_MPDU_LEN_VHT_3895 3895 | |
| #define IEEE80211_MAX_MPDU_LEN_VHT_7991 7991 | |
| #define IEEE80211_MAX_MPDU_LEN_VHT_11454 11454 | |
| #define IEEE80211_MAX_SSID_LEN 32 | |
| #define IEEE80211_MAX_MESH_ID_LEN 32 | |
| #define IEEE80211_FIRST_TSPEC_TSID 8 | |
| #define IEEE80211_NUM_TIDS 16 | |
| /* number of user priorities 802.11 uses */ | |
| #define IEEE80211_NUM_UPS 8 | |
| /* number of ACs */ | |
| #define IEEE80211_NUM_ACS 4 | |
| #define IEEE80211_QOS_CTL_LEN 2 | |
| /* 1d tag mask */ | |
| #define IEEE80211_QOS_CTL_TAG1D_MASK 0x0007 | |
| /* TID mask */ | |
| #define IEEE80211_QOS_CTL_TID_MASK 0x000f | |
| /* EOSP */ | |
| #define IEEE80211_QOS_CTL_EOSP 0x0010 | |
| /* ACK policy */ | |
| #define IEEE80211_QOS_CTL_ACK_POLICY_NORMAL 0x0000 | |
| #define IEEE80211_QOS_CTL_ACK_POLICY_NOACK 0x0020 | |
| #define IEEE80211_QOS_CTL_ACK_POLICY_NO_EXPL 0x0040 | |
| #define IEEE80211_QOS_CTL_ACK_POLICY_BLOCKACK 0x0060 | |
| #define IEEE80211_QOS_CTL_ACK_POLICY_MASK 0x0060 | |
| /* A-MSDU 802.11n */ | |
| #define IEEE80211_QOS_CTL_A_MSDU_PRESENT 0x0080 | |
| /* Mesh Control 802.11s */ | |
| #define IEEE80211_QOS_CTL_MESH_CONTROL_PRESENT 0x0100 | |
| /* Mesh Power Save Level */ | |
| #define IEEE80211_QOS_CTL_MESH_PS_LEVEL 0x0200 | |
| /* Mesh Receiver Service Period Initiated */ | |
| #define IEEE80211_QOS_CTL_RSPI 0x0400 | |
| /* U-APSD queue for WMM IEs sent by AP */ | |
| #define IEEE80211_WMM_IE_AP_QOSINFO_UAPSD (1<<7) | |
| #define IEEE80211_WMM_IE_AP_QOSINFO_PARAM_SET_CNT_MASK 0x0f | |
| /* U-APSD queues for WMM IEs sent by STA */ | |
| #define IEEE80211_WMM_IE_STA_QOSINFO_AC_VO (1<<0) | |
| #define IEEE80211_WMM_IE_STA_QOSINFO_AC_VI (1<<1) | |
| #define IEEE80211_WMM_IE_STA_QOSINFO_AC_BK (1<<2) | |
| #define IEEE80211_WMM_IE_STA_QOSINFO_AC_BE (1<<3) | |
| #define IEEE80211_WMM_IE_STA_QOSINFO_AC_MASK 0x0f | |
| /* U-APSD max SP length for WMM IEs sent by STA */ | |
| #define IEEE80211_WMM_IE_STA_QOSINFO_SP_ALL 0x00 | |
| #define IEEE80211_WMM_IE_STA_QOSINFO_SP_2 0x01 | |
| #define IEEE80211_WMM_IE_STA_QOSINFO_SP_4 0x02 | |
| #define IEEE80211_WMM_IE_STA_QOSINFO_SP_6 0x03 | |
| #define IEEE80211_WMM_IE_STA_QOSINFO_SP_MASK 0x03 | |
| #define IEEE80211_WMM_IE_STA_QOSINFO_SP_SHIFT 5 | |
| #define IEEE80211_HT_CTL_LEN 4 | |
| struct ieee80211_hdr { | |
| __le16 frame_control; | |
| __le16 duration_id; | |
| u8 addr1[ETH_ALEN]; | |
| u8 addr2[ETH_ALEN]; | |
| u8 addr3[ETH_ALEN]; | |
| __le16 seq_ctrl; | |
| u8 addr4[ETH_ALEN]; | |
| } __packed __aligned(2); | |
| struct ieee80211_hdr_3addr { | |
| __le16 frame_control; | |
| __le16 duration_id; | |
| u8 addr1[ETH_ALEN]; | |
| u8 addr2[ETH_ALEN]; | |
| u8 addr3[ETH_ALEN]; | |
| __le16 seq_ctrl; | |
| } __packed __aligned(2); | |
| struct ieee80211_qos_hdr { | |
| __le16 frame_control; | |
| __le16 duration_id; | |
| u8 addr1[ETH_ALEN]; | |
| u8 addr2[ETH_ALEN]; | |
| u8 addr3[ETH_ALEN]; | |
| __le16 seq_ctrl; | |
| __le16 qos_ctrl; | |
| } __packed __aligned(2); | |
| /** | |
| * ieee80211_has_tods - check if IEEE80211_FCTL_TODS is set | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_has_tods(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_TODS)) != 0; | |
| } | |
| /** | |
| * ieee80211_has_fromds - check if IEEE80211_FCTL_FROMDS is set | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_has_fromds(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FROMDS)) != 0; | |
| } | |
| /** | |
| * ieee80211_has_a4 - check if IEEE80211_FCTL_TODS and IEEE80211_FCTL_FROMDS are set | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_has_a4(__le16 fc) | |
| { | |
| __le16 tmp = cpu_to_le16(IEEE80211_FCTL_TODS | IEEE80211_FCTL_FROMDS); | |
| return (fc & tmp) == tmp; | |
| } | |
| /** | |
| * ieee80211_has_morefrags - check if IEEE80211_FCTL_MOREFRAGS is set | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_has_morefrags(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_MOREFRAGS)) != 0; | |
| } | |
| /** | |
| * ieee80211_has_retry - check if IEEE80211_FCTL_RETRY is set | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_has_retry(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_RETRY)) != 0; | |
| } | |
| /** | |
| * ieee80211_has_pm - check if IEEE80211_FCTL_PM is set | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_has_pm(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_PM)) != 0; | |
| } | |
| /** | |
| * ieee80211_has_moredata - check if IEEE80211_FCTL_MOREDATA is set | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_has_moredata(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_MOREDATA)) != 0; | |
| } | |
| /** | |
| * ieee80211_has_protected - check if IEEE80211_FCTL_PROTECTED is set | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_has_protected(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_PROTECTED)) != 0; | |
| } | |
| /** | |
| * ieee80211_has_order - check if IEEE80211_FCTL_ORDER is set | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_has_order(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_ORDER)) != 0; | |
| } | |
| /** | |
| * ieee80211_is_mgmt - check if type is IEEE80211_FTYPE_MGMT | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_mgmt(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_MGMT); | |
| } | |
| /** | |
| * ieee80211_is_ctl - check if type is IEEE80211_FTYPE_CTL | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_ctl(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_CTL); | |
| } | |
| /** | |
| * ieee80211_is_data - check if type is IEEE80211_FTYPE_DATA | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_data(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_DATA); | |
| } | |
| /** | |
| * ieee80211_is_ext - check if type is IEEE80211_FTYPE_EXT | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_ext(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_EXT); | |
| } | |
| /** | |
| * ieee80211_is_data_qos - check if type is IEEE80211_FTYPE_DATA and IEEE80211_STYPE_QOS_DATA is set | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_data_qos(__le16 fc) | |
| { | |
| /* | |
| * mask with QOS_DATA rather than IEEE80211_FCTL_STYPE as we just need | |
| * to check the one bit | |
| */ | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_STYPE_QOS_DATA)) == | |
| cpu_to_le16(IEEE80211_FTYPE_DATA | IEEE80211_STYPE_QOS_DATA); | |
| } | |
| /** | |
| * ieee80211_is_data_present - check if type is IEEE80211_FTYPE_DATA and has data | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_data_present(__le16 fc) | |
| { | |
| /* | |
| * mask with 0x40 and test that that bit is clear to only return true | |
| * for the data-containing substypes. | |
| */ | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | 0x40)) == | |
| cpu_to_le16(IEEE80211_FTYPE_DATA); | |
| } | |
| /** | |
| * ieee80211_is_assoc_req - check if IEEE80211_FTYPE_MGMT && IEEE80211_STYPE_ASSOC_REQ | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_assoc_req(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_MGMT | IEEE80211_STYPE_ASSOC_REQ); | |
| } | |
| /** | |
| * ieee80211_is_assoc_resp - check if IEEE80211_FTYPE_MGMT && IEEE80211_STYPE_ASSOC_RESP | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_assoc_resp(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_MGMT | IEEE80211_STYPE_ASSOC_RESP); | |
| } | |
| /** | |
| * ieee80211_is_reassoc_req - check if IEEE80211_FTYPE_MGMT && IEEE80211_STYPE_REASSOC_REQ | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_reassoc_req(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_MGMT | IEEE80211_STYPE_REASSOC_REQ); | |
| } | |
| /** | |
| * ieee80211_is_reassoc_resp - check if IEEE80211_FTYPE_MGMT && IEEE80211_STYPE_REASSOC_RESP | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_reassoc_resp(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_MGMT | IEEE80211_STYPE_REASSOC_RESP); | |
| } | |
| /** | |
| * ieee80211_is_probe_req - check if IEEE80211_FTYPE_MGMT && IEEE80211_STYPE_PROBE_REQ | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_probe_req(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_MGMT | IEEE80211_STYPE_PROBE_REQ); | |
| } | |
| /** | |
| * ieee80211_is_probe_resp - check if IEEE80211_FTYPE_MGMT && IEEE80211_STYPE_PROBE_RESP | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_probe_resp(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_MGMT | IEEE80211_STYPE_PROBE_RESP); | |
| } | |
| /** | |
| * ieee80211_is_beacon - check if IEEE80211_FTYPE_MGMT && IEEE80211_STYPE_BEACON | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_beacon(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_MGMT | IEEE80211_STYPE_BEACON); | |
| } | |
| /** | |
| * ieee80211_is_s1g_beacon - check if IEEE80211_FTYPE_EXT && | |
| * IEEE80211_STYPE_S1G_BEACON | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_s1g_beacon(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | | |
| IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_EXT | IEEE80211_STYPE_S1G_BEACON); | |
| } | |
| /** | |
| * ieee80211_next_tbtt_present - check if IEEE80211_FTYPE_EXT && | |
| * IEEE80211_STYPE_S1G_BEACON && IEEE80211_S1G_BCN_NEXT_TBTT | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_next_tbtt_present(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_EXT | IEEE80211_STYPE_S1G_BEACON) && | |
| fc & cpu_to_le16(IEEE80211_S1G_BCN_NEXT_TBTT); | |
| } | |
| /** | |
| * ieee80211_is_s1g_short_beacon - check if next tbtt present bit is set. Only | |
| * true for S1G beacons when they're short. | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_s1g_short_beacon(__le16 fc) | |
| { | |
| return ieee80211_is_s1g_beacon(fc) && ieee80211_next_tbtt_present(fc); | |
| } | |
| /** | |
| * ieee80211_is_atim - check if IEEE80211_FTYPE_MGMT && IEEE80211_STYPE_ATIM | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_atim(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_MGMT | IEEE80211_STYPE_ATIM); | |
| } | |
| /** | |
| * ieee80211_is_disassoc - check if IEEE80211_FTYPE_MGMT && IEEE80211_STYPE_DISASSOC | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_disassoc(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_MGMT | IEEE80211_STYPE_DISASSOC); | |
| } | |
| /** | |
| * ieee80211_is_auth - check if IEEE80211_FTYPE_MGMT && IEEE80211_STYPE_AUTH | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_auth(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_MGMT | IEEE80211_STYPE_AUTH); | |
| } | |
| /** | |
| * ieee80211_is_deauth - check if IEEE80211_FTYPE_MGMT && IEEE80211_STYPE_DEAUTH | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_deauth(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_MGMT | IEEE80211_STYPE_DEAUTH); | |
| } | |
| /** | |
| * ieee80211_is_action - check if IEEE80211_FTYPE_MGMT && IEEE80211_STYPE_ACTION | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_action(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_MGMT | IEEE80211_STYPE_ACTION); | |
| } | |
| /** | |
| * ieee80211_is_back_req - check if IEEE80211_FTYPE_CTL && IEEE80211_STYPE_BACK_REQ | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_back_req(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_CTL | IEEE80211_STYPE_BACK_REQ); | |
| } | |
| /** | |
| * ieee80211_is_back - check if IEEE80211_FTYPE_CTL && IEEE80211_STYPE_BACK | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_back(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_CTL | IEEE80211_STYPE_BACK); | |
| } | |
| /** | |
| * ieee80211_is_pspoll - check if IEEE80211_FTYPE_CTL && IEEE80211_STYPE_PSPOLL | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_pspoll(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_CTL | IEEE80211_STYPE_PSPOLL); | |
| } | |
| /** | |
| * ieee80211_is_rts - check if IEEE80211_FTYPE_CTL && IEEE80211_STYPE_RTS | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_rts(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_CTL | IEEE80211_STYPE_RTS); | |
| } | |
| /** | |
| * ieee80211_is_cts - check if IEEE80211_FTYPE_CTL && IEEE80211_STYPE_CTS | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_cts(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_CTL | IEEE80211_STYPE_CTS); | |
| } | |
| /** | |
| * ieee80211_is_ack - check if IEEE80211_FTYPE_CTL && IEEE80211_STYPE_ACK | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_ack(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_CTL | IEEE80211_STYPE_ACK); | |
| } | |
| /** | |
| * ieee80211_is_cfend - check if IEEE80211_FTYPE_CTL && IEEE80211_STYPE_CFEND | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_cfend(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_CTL | IEEE80211_STYPE_CFEND); | |
| } | |
| /** | |
| * ieee80211_is_cfendack - check if IEEE80211_FTYPE_CTL && IEEE80211_STYPE_CFENDACK | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_cfendack(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_CTL | IEEE80211_STYPE_CFENDACK); | |
| } | |
| /** | |
| * ieee80211_is_nullfunc - check if frame is a regular (non-QoS) nullfunc frame | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_nullfunc(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_DATA | IEEE80211_STYPE_NULLFUNC); | |
| } | |
| /** | |
| * ieee80211_is_qos_nullfunc - check if frame is a QoS nullfunc frame | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_qos_nullfunc(__le16 fc) | |
| { | |
| return (fc & cpu_to_le16(IEEE80211_FCTL_FTYPE | IEEE80211_FCTL_STYPE)) == | |
| cpu_to_le16(IEEE80211_FTYPE_DATA | IEEE80211_STYPE_QOS_NULLFUNC); | |
| } | |
| /** | |
| * ieee80211_is_any_nullfunc - check if frame is regular or QoS nullfunc frame | |
| * @fc: frame control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_any_nullfunc(__le16 fc) | |
| { | |
| return (ieee80211_is_nullfunc(fc) || ieee80211_is_qos_nullfunc(fc)); | |
| } | |
| /** | |
| * ieee80211_is_bufferable_mmpdu - check if frame is bufferable MMPDU | |
| * @fc: frame control field in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_bufferable_mmpdu(__le16 fc) | |
| { | |
| /* IEEE 802.11-2012, definition of "bufferable management frame"; | |
| * note that this ignores the IBSS special case. */ | |
| return ieee80211_is_mgmt(fc) && | |
| (ieee80211_is_action(fc) || | |
| ieee80211_is_disassoc(fc) || | |
| ieee80211_is_deauth(fc)); | |
| } | |
| /** | |
| * ieee80211_is_first_frag - check if IEEE80211_SCTL_FRAG is not set | |
| * @seq_ctrl: frame sequence control bytes in little-endian byteorder | |
| */ | |
| static inline bool ieee80211_is_first_frag(__le16 seq_ctrl) | |
| { | |
| return (seq_ctrl & cpu_to_le16(IEEE80211_SCTL_FRAG)) == 0; | |
| } | |
| /** | |
| * ieee80211_is_frag - check if a frame is a fragment | |
| * @hdr: 802.11 header of the frame | |
| */ | |
| static inline bool ieee80211_is_frag(struct ieee80211_hdr *hdr) | |
| { | |
| return ieee80211_has_morefrags(hdr->frame_control) || | |
| hdr->seq_ctrl & cpu_to_le16(IEEE80211_SCTL_FRAG); | |
| } | |
| struct ieee80211s_hdr { | |
| u8 flags; | |
| u8 ttl; | |
| __le32 seqnum; | |
| u8 eaddr1[ETH_ALEN]; | |
| u8 eaddr2[ETH_ALEN]; | |
| } __packed __aligned(2); | |
| /* Mesh flags */ | |
| #define MESH_FLAGS_AE_A4 0x1 | |
| #define MESH_FLAGS_AE_A5_A6 0x2 | |
| #define MESH_FLAGS_AE 0x3 | |
| #define MESH_FLAGS_PS_DEEP 0x4 | |
| /** | |
| * enum ieee80211_preq_flags - mesh PREQ element flags | |
| * | |
| * @IEEE80211_PREQ_PROACTIVE_PREP_FLAG: proactive PREP subfield | |
| */ | |
| enum ieee80211_preq_flags { | |
| IEEE80211_PREQ_PROACTIVE_PREP_FLAG = 1<<2, | |
| }; | |
| /** | |
| * enum ieee80211_preq_target_flags - mesh PREQ element per target flags | |
| * | |
| * @IEEE80211_PREQ_TO_FLAG: target only subfield | |
| * @IEEE80211_PREQ_USN_FLAG: unknown target HWMP sequence number subfield | |
| */ | |
| enum ieee80211_preq_target_flags { | |
| IEEE80211_PREQ_TO_FLAG = 1<<0, | |
| IEEE80211_PREQ_USN_FLAG = 1<<2, | |
| }; | |
| /** | |
| * struct ieee80211_quiet_ie | |
| * | |
| * This structure refers to "Quiet information element" | |
| */ | |
| struct ieee80211_quiet_ie { | |
| u8 count; | |
| u8 period; | |
| __le16 duration; | |
| __le16 offset; | |
| } __packed; | |
| /** | |
| * struct ieee80211_msrment_ie | |
| * | |
| * This structure refers to "Measurement Request/Report information element" | |
| */ | |
| struct ieee80211_msrment_ie { | |
| u8 token; | |
| u8 mode; | |
| u8 type; | |
| u8 request[]; | |
| } __packed; | |
| /** | |
| * struct ieee80211_channel_sw_ie | |
| * | |
| * This structure refers to "Channel Switch Announcement information element" | |
| */ | |
| struct ieee80211_channel_sw_ie { | |
| u8 mode; | |
| u8 new_ch_num; | |
| u8 count; | |
| } __packed; | |
| /** | |
| * struct ieee80211_ext_chansw_ie | |
| * | |
| * This structure represents the "Extended Channel Switch Announcement element" | |
| */ | |
| struct ieee80211_ext_chansw_ie { | |
| u8 mode; | |
| u8 new_operating_class; | |
| u8 new_ch_num; | |
| u8 count; | |
| } __packed; | |
| /** | |
| * struct ieee80211_sec_chan_offs_ie - secondary channel offset IE | |
| * @sec_chan_offs: secondary channel offset, uses IEEE80211_HT_PARAM_CHA_SEC_* | |
| * values here | |
| * This structure represents the "Secondary Channel Offset element" | |
| */ | |
| struct ieee80211_sec_chan_offs_ie { | |
| u8 sec_chan_offs; | |
| } __packed; | |
| /** | |
| * struct ieee80211_mesh_chansw_params_ie - mesh channel switch parameters IE | |
| * | |
| * This structure represents the "Mesh Channel Switch Paramters element" | |
| */ | |
| struct ieee80211_mesh_chansw_params_ie { | |
| u8 mesh_ttl; | |
| u8 mesh_flags; | |
| __le16 mesh_reason; | |
| __le16 mesh_pre_value; | |
| } __packed; | |
| /** | |
| * struct ieee80211_wide_bw_chansw_ie - wide bandwidth channel switch IE | |
| */ | |
| struct ieee80211_wide_bw_chansw_ie { | |
| u8 new_channel_width; | |
| u8 new_center_freq_seg0, new_center_freq_seg1; | |
| } __packed; | |
| /** | |
| * struct ieee80211_tim | |
| * | |
| * This structure refers to "Traffic Indication Map information element" | |
| */ | |
| struct ieee80211_tim_ie { | |
| u8 dtim_count; | |
| u8 dtim_period; | |
| u8 bitmap_ctrl; | |
| /* variable size: 1 - 251 bytes */ | |
| u8 virtual_map[1]; | |
| } __packed; | |
| /** | |
| * struct ieee80211_meshconf_ie | |
| * | |
| * This structure refers to "Mesh Configuration information element" | |
| */ | |
| struct ieee80211_meshconf_ie { | |
| u8 meshconf_psel; | |
| u8 meshconf_pmetric; | |
| u8 meshconf_congest; | |
| u8 meshconf_synch; | |
| u8 meshconf_auth; | |
| u8 meshconf_form; | |
| u8 meshconf_cap; | |
| } __packed; | |
| /** | |
| * enum mesh_config_capab_flags - Mesh Configuration IE capability field flags | |
| * | |
| * @IEEE80211_MESHCONF_CAPAB_ACCEPT_PLINKS: STA is willing to establish | |
| * additional mesh peerings with other mesh STAs | |
| * @IEEE80211_MESHCONF_CAPAB_FORWARDING: the STA forwards MSDUs | |
| * @IEEE80211_MESHCONF_CAPAB_TBTT_ADJUSTING: TBTT adjustment procedure | |
| * is ongoing | |
| * @IEEE80211_MESHCONF_CAPAB_POWER_SAVE_LEVEL: STA is in deep sleep mode or has | |
| * neighbors in deep sleep mode | |
| */ | |
| enum mesh_config_capab_flags { | |
| IEEE80211_MESHCONF_CAPAB_ACCEPT_PLINKS = 0x01, | |
| IEEE80211_MESHCONF_CAPAB_FORWARDING = 0x08, | |
| IEEE80211_MESHCONF_CAPAB_TBTT_ADJUSTING = 0x20, | |
| IEEE80211_MESHCONF_CAPAB_POWER_SAVE_LEVEL = 0x40, | |
| }; | |
| #define IEEE80211_MESHCONF_FORM_CONNECTED_TO_GATE 0x1 | |
| /** | |
| * mesh channel switch parameters element's flag indicator | |
| * | |
| */ | |
| #define WLAN_EID_CHAN_SWITCH_PARAM_TX_RESTRICT BIT(0) | |
| #define WLAN_EID_CHAN_SWITCH_PARAM_INITIATOR BIT(1) | |
| #define WLAN_EID_CHAN_SWITCH_PARAM_REASON BIT(2) | |
| /** | |
| * struct ieee80211_rann_ie | |
| * | |
| * This structure refers to "Root Announcement information element" | |
| */ | |
| struct ieee80211_rann_ie { | |
| u8 rann_flags; | |
| u8 rann_hopcount; | |
| u8 rann_ttl; | |
| u8 rann_addr[ETH_ALEN]; | |
| __le32 rann_seq; | |
| __le32 rann_interval; | |
| __le32 rann_metric; | |
| } __packed; | |
| enum ieee80211_rann_flags { | |
| RANN_FLAG_IS_GATE = 1 << 0, | |
| }; | |
| enum ieee80211_ht_chanwidth_values { | |
| IEEE80211_HT_CHANWIDTH_20MHZ = 0, | |
| IEEE80211_HT_CHANWIDTH_ANY = 1, | |
| }; | |
| /** | |
| * enum ieee80211_opmode_bits - VHT operating mode field bits | |
| * @IEEE80211_OPMODE_NOTIF_CHANWIDTH_MASK: channel width mask | |
| * @IEEE80211_OPMODE_NOTIF_CHANWIDTH_20MHZ: 20 MHz channel width | |
| * @IEEE80211_OPMODE_NOTIF_CHANWIDTH_40MHZ: 40 MHz channel width | |
| * @IEEE80211_OPMODE_NOTIF_CHANWIDTH_80MHZ: 80 MHz channel width | |
| * @IEEE80211_OPMODE_NOTIF_CHANWIDTH_160MHZ: 160 MHz or 80+80 MHz channel width | |
| * @IEEE80211_OPMODE_NOTIF_BW_160_80P80: 160 / 80+80 MHz indicator flag | |
| * @IEEE80211_OPMODE_NOTIF_RX_NSS_MASK: number of spatial streams mask | |
| * (the NSS value is the value of this field + 1) | |
| * @IEEE80211_OPMODE_NOTIF_RX_NSS_SHIFT: number of spatial streams shift | |
| * @IEEE80211_OPMODE_NOTIF_RX_NSS_TYPE_BF: indicates streams in SU-MIMO PPDU | |
| * using a beamforming steering matrix | |
| */ | |
| enum ieee80211_vht_opmode_bits { | |
| IEEE80211_OPMODE_NOTIF_CHANWIDTH_MASK = 0x03, | |
| IEEE80211_OPMODE_NOTIF_CHANWIDTH_20MHZ = 0, | |
| IEEE80211_OPMODE_NOTIF_CHANWIDTH_40MHZ = 1, | |
| IEEE80211_OPMODE_NOTIF_CHANWIDTH_80MHZ = 2, | |
| IEEE80211_OPMODE_NOTIF_CHANWIDTH_160MHZ = 3, | |
| IEEE80211_OPMODE_NOTIF_BW_160_80P80 = 0x04, | |
| IEEE80211_OPMODE_NOTIF_RX_NSS_MASK = 0x70, | |
| IEEE80211_OPMODE_NOTIF_RX_NSS_SHIFT = 4, | |
| IEEE80211_OPMODE_NOTIF_RX_NSS_TYPE_BF = 0x80, | |
| }; | |
| /** | |
| * enum ieee80211_s1g_chanwidth | |
| * These are defined in IEEE802.11-2016ah Table 10-20 | |
| * as BSS Channel Width | |
| * | |
| * @IEEE80211_S1G_CHANWIDTH_1MHZ: 1MHz operating channel | |
| * @IEEE80211_S1G_CHANWIDTH_2MHZ: 2MHz operating channel | |
| * @IEEE80211_S1G_CHANWIDTH_4MHZ: 4MHz operating channel | |
| * @IEEE80211_S1G_CHANWIDTH_8MHZ: 8MHz operating channel | |
| * @IEEE80211_S1G_CHANWIDTH_16MHZ: 16MHz operating channel | |
| */ | |
| enum ieee80211_s1g_chanwidth { | |
| IEEE80211_S1G_CHANWIDTH_1MHZ = 0, | |
| IEEE80211_S1G_CHANWIDTH_2MHZ = 1, | |
| IEEE80211_S1G_CHANWIDTH_4MHZ = 3, | |
| IEEE80211_S1G_CHANWIDTH_8MHZ = 7, | |
| IEEE80211_S1G_CHANWIDTH_16MHZ = 15, | |
| }; | |
| #define WLAN_SA_QUERY_TR_ID_LEN 2 | |
| #define WLAN_MEMBERSHIP_LEN 8 | |
| #define WLAN_USER_POSITION_LEN 16 | |
| /** | |
| * struct ieee80211_tpc_report_ie | |
| * | |
| * This structure refers to "TPC Report element" | |
| */ | |
| struct ieee80211_tpc_report_ie { | |
| u8 tx_power; | |
| u8 link_margin; | |
| } __packed; | |
| #define IEEE80211_ADDBA_EXT_FRAG_LEVEL_MASK GENMASK(2, 1) | |
| #define IEEE80211_ADDBA_EXT_FRAG_LEVEL_SHIFT 1 | |
| #define IEEE80211_ADDBA_EXT_NO_FRAG BIT(0) | |
| struct ieee80211_addba_ext_ie { | |
| u8 data; | |
| } __packed; | |
| /** | |
| * struct ieee80211_s1g_bcn_compat_ie | |
| * | |
| * S1G Beacon Compatibility element | |
| */ | |
| struct ieee80211_s1g_bcn_compat_ie { | |
| __le16 compat_info; | |
| __le16 beacon_int; | |
| __le32 tsf_completion; | |
| } __packed; | |
| /** | |
| * struct ieee80211_s1g_oper_ie | |
| * | |
| * S1G Operation element | |
| */ | |
| struct ieee80211_s1g_oper_ie { | |
| u8 ch_width; | |
| u8 oper_class; | |
| u8 primary_ch; | |
| u8 oper_ch; | |
| __le16 basic_mcs_nss; | |
| } __packed; | |
| /** | |
| * struct ieee80211_aid_response_ie | |
| * | |
| * AID Response element | |
| */ | |
| struct ieee80211_aid_response_ie { | |
| __le16 aid; | |
| u8 switch_count; | |
| __le16 response_int; | |
| } __packed; | |
| struct ieee80211_s1g_cap { | |
| u8 capab_info[10]; | |
| u8 supp_mcs_nss[5]; | |
| } __packed; | |
| struct ieee80211_ext { | |
| __le16 frame_control; | |
| __le16 duration; | |
| union { | |
| struct { | |
| u8 sa[ETH_ALEN]; | |
| __le32 timestamp; | |
| u8 change_seq; | |
| u8 variable[0]; | |
| } __packed s1g_beacon; | |
| struct { | |
| u8 sa[ETH_ALEN]; | |
| __le32 timestamp; | |
| u8 change_seq; | |
| u8 next_tbtt[3]; | |
| u8 variable[0]; | |
| } __packed s1g_short_beacon; | |
| } u; | |
| } __packed __aligned(2); | |
| struct ieee80211_mgmt { | |
| __le16 frame_control; | |
| __le16 duration; | |
| u8 da[ETH_ALEN]; | |
| u8 sa[ETH_ALEN]; | |
| u8 bssid[ETH_ALEN]; | |
| __le16 seq_ctrl; | |
| union { | |
| struct { | |
| __le16 auth_alg; | |
| __le16 auth_transaction; | |
| __le16 status_code; | |
| /* possibly followed by Challenge text */ | |
| u8 variable[0]; | |
| } __packed auth; | |
| struct { | |
| __le16 reason_code; | |
| } __packed deauth; | |
| struct { | |
| __le16 capab_info; | |
| __le16 listen_interval; | |
| /* followed by SSID and Supported rates */ | |
| u8 variable[0]; | |
| } __packed assoc_req; | |
| struct { | |
| __le16 capab_info; | |
| __le16 status_code; | |
| __le16 aid; | |
| /* followed by Supported rates */ | |
| u8 variable[0]; | |
| } __packed assoc_resp, reassoc_resp; | |
| struct { | |
| __le16 capab_info; | |
| __le16 status_code; | |
| u8 variable[0]; | |
| } __packed s1g_assoc_resp, s1g_reassoc_resp; | |
| struct { | |
| __le16 capab_info; | |
| __le16 listen_interval; | |
| u8 current_ap[ETH_ALEN]; | |
| /* followed by SSID and Supported rates */ | |
| u8 variable[0]; | |
| } __packed reassoc_req; | |
| struct { | |
| __le16 reason_code; | |
| } __packed disassoc; | |
| struct { | |
| __le64 timestamp; | |
| __le16 beacon_int; | |
| __le16 capab_info; | |
| /* followed by some of SSID, Supported rates, | |
| * FH Params, DS Params, CF Params, IBSS Params, TIM */ | |
| u8 variable[0]; | |
| } __packed beacon; | |
| struct { | |
| /* only variable items: SSID, Supported rates */ | |
| u8 variable[0]; | |
| } __packed probe_req; | |
| struct { | |
| __le64 timestamp; | |
| __le16 beacon_int; | |
| __le16 capab_info; | |
| /* followed by some of SSID, Supported rates, | |
| * FH Params, DS Params, CF Params, IBSS Params */ | |
| u8 variable[0]; | |
| } __packed probe_resp; | |
| struct { | |
| u8 category; | |
| union { | |
| struct { | |
| u8 action_code; | |
| u8 dialog_token; | |
| u8 status_code; | |
| u8 variable[0]; | |
| } __packed wme_action; | |
| struct{ | |
| u8 action_code; | |
| u8 variable[0]; | |
| } __packed chan_switch; | |
| struct{ | |
| u8 action_code; | |
| struct ieee80211_ext_chansw_ie data; | |
| u8 variable[0]; | |
| } __packed ext_chan_switch; | |
| struct{ | |
| u8 action_code; | |
| u8 dialog_token; | |
| u8 element_id; | |
| u8 length; | |
| struct ieee80211_msrment_ie msr_elem; | |
| } __packed measurement; | |
| struct{ | |
| u8 action_code; | |
| u8 dialog_token; | |
| __le16 capab; | |
| __le16 timeout; | |
| __le16 start_seq_num; | |
| /* followed by BA Extension */ | |
| u8 variable[0]; | |
| } __packed addba_req; | |
| struct{ | |
| u8 action_code; | |
| u8 dialog_token; | |
| __le16 status; | |
| __le16 capab; | |
| __le16 timeout; | |
| } __packed addba_resp; | |
| struct{ | |
| u8 action_code; | |
| __le16 params; | |
| __le16 reason_code; | |
| } __packed delba; | |
| struct { | |
| u8 action_code; | |
| u8 variable[0]; | |
| } __packed self_prot; | |
| struct{ | |
| u8 action_code; | |
| u8 variable[0]; | |
| } __packed mesh_action; | |
| struct { | |
| u8 action; | |
| u8 trans_id[WLAN_SA_QUERY_TR_ID_LEN]; | |
| } __packed sa_query; | |
| struct { | |
| u8 action; | |
| u8 smps_control; | |
| } __packed ht_smps; | |
| struct { | |
| u8 action_code; | |
| u8 chanwidth; | |
| } __packed ht_notify_cw; | |
| struct { | |
| u8 action_code; | |
| u8 dialog_token; | |
| __le16 capability; | |
| u8 variable[0]; | |
| } __packed tdls_discover_resp; | |
| struct { | |
| u8 action_code; | |
| u8 operating_mode; | |
| } __packed vht_opmode_notif; | |
| struct { | |
| u8 action_code; | |
| u8 membership[WLAN_MEMBERSHIP_LEN]; | |
| u8 position[WLAN_USER_POSITION_LEN]; | |
| } __packed vht_group_notif; | |
| struct { | |
| u8 action_code; | |
| u8 dialog_token; | |
| u8 tpc_elem_id; | |
| u8 tpc_elem_length; | |
| struct ieee80211_tpc_report_ie tpc; | |
| } __packed tpc_report; | |
| struct { | |
| u8 action_code; | |
| u8 dialog_token; | |
| u8 follow_up; | |
| u8 tod[6]; | |
| u8 toa[6]; | |
| __le16 tod_error; | |
| __le16 toa_error; | |
| u8 variable[0]; | |
| } __packed ftm; | |
| } u; | |
| } __packed action; | |
| } u; | |
| } __packed __aligned(2); | |
| /* Supported rates membership selectors */ | |
| #define BSS_MEMBERSHIP_SELECTOR_HT_PHY 127 | |
| #define BSS_MEMBERSHIP_SELECTOR_VHT_PHY 126 | |
| #define BSS_MEMBERSHIP_SELECTOR_HE_PHY 122 | |
| /* mgmt header + 1 byte category code */ | |
| #define IEEE80211_MIN_ACTION_SIZE offsetof(struct ieee80211_mgmt, u.action.u) | |
| /* Management MIC information element (IEEE 802.11w) */ | |
| struct ieee80211_mmie { | |
| u8 element_id; | |
| u8 length; | |
| __le16 key_id; | |
| u8 sequence_number[6]; | |
| u8 mic[8]; | |
| } __packed; | |
| /* Management MIC information element (IEEE 802.11w) for GMAC and CMAC-256 */ | |
| struct ieee80211_mmie_16 { | |
| u8 element_id; | |
| u8 length; | |
| __le16 key_id; | |
| u8 sequence_number[6]; | |
| u8 mic[16]; | |
| } __packed; | |
| struct ieee80211_vendor_ie { | |
| u8 element_id; | |
| u8 len; | |
| u8 oui[3]; | |
| u8 oui_type; | |
| } __packed; | |
| struct ieee80211_wmm_ac_param { | |
| u8 aci_aifsn; /* AIFSN, ACM, ACI */ | |
| u8 cw; /* ECWmin, ECWmax (CW = 2^ECW - 1) */ | |
| __le16 txop_limit; | |
| } __packed; | |
| struct ieee80211_wmm_param_ie { | |
| u8 element_id; /* Element ID: 221 (0xdd); */ | |
| u8 len; /* Length: 24 */ | |
| /* required fields for WMM version 1 */ | |
| u8 oui[3]; /* 00:50:f2 */ | |
| u8 oui_type; /* 2 */ | |
| u8 oui_subtype; /* 1 */ | |
| u8 version; /* 1 for WMM version 1.0 */ | |
| u8 qos_info; /* AP/STA specific QoS info */ | |
| u8 reserved; /* 0 */ | |
| /* AC_BE, AC_BK, AC_VI, AC_VO */ | |
| struct ieee80211_wmm_ac_param ac[4]; | |
| } __packed; | |
| /* Control frames */ | |
| struct ieee80211_rts { | |
| __le16 frame_control; | |
| __le16 duration; | |
| u8 ra[ETH_ALEN]; | |
| u8 ta[ETH_ALEN]; | |
| } __packed __aligned(2); | |
| struct ieee80211_cts { | |
| __le16 frame_control; | |
| __le16 duration; | |
| u8 ra[ETH_ALEN]; | |
| } __packed __aligned(2); | |
| struct ieee80211_pspoll { | |
| __le16 frame_control; | |
| __le16 aid; | |
| u8 bssid[ETH_ALEN]; | |
| u8 ta[ETH_ALEN]; | |
| } __packed __aligned(2); | |
| /* TDLS */ | |
| /* Channel switch timing */ | |
| struct ieee80211_ch_switch_timing { | |
| __le16 switch_time; | |
| __le16 switch_timeout; | |
| } __packed; | |
| /* Link-id information element */ | |
| struct ieee80211_tdls_lnkie { | |
| u8 ie_type; /* Link Identifier IE */ | |
| u8 ie_len; | |
| u8 bssid[ETH_ALEN]; | |
| u8 init_sta[ETH_ALEN]; | |
| u8 resp_sta[ETH_ALEN]; | |
| } __packed; | |
| struct ieee80211_tdls_data { | |
| u8 da[ETH_ALEN]; | |
| u8 sa[ETH_ALEN]; | |
| __be16 ether_type; | |
| u8 payload_type; | |
| u8 category; | |
| u8 action_code; | |
| union { | |
| struct { | |
| u8 dialog_token; | |
| __le16 capability; | |
| u8 variable[0]; | |
| } __packed setup_req; | |
| struct { | |
| __le16 status_code; | |
| u8 dialog_token; | |
| __le16 capability; | |
| u8 variable[0]; | |
| } __packed setup_resp; | |
| struct { | |
| __le16 status_code; | |
| u8 dialog_token; | |
| u8 variable[0]; | |
| } __packed setup_cfm; | |
| struct { | |
| __le16 reason_code; | |
| u8 variable[0]; | |
| } __packed teardown; | |
| struct { | |
| u8 dialog_token; | |
| u8 variable[0]; | |
| } __packed discover_req; | |
| struct { | |
| u8 target_channel; | |
| u8 oper_class; | |
| u8 variable[0]; | |
| } __packed chan_switch_req; | |
| struct { | |
| __le16 status_code; | |
| u8 variable[0]; | |
| } __packed chan_switch_resp; | |
| } u; | |
| } __packed; | |
| /* | |
| * Peer-to-Peer IE attribute related definitions. | |
| */ | |
| /** | |
| * enum ieee80211_p2p_attr_id - identifies type of peer-to-peer attribute. | |
| */ | |
| enum ieee80211_p2p_attr_id { | |
| IEEE80211_P2P_ATTR_STATUS = 0, | |
| IEEE80211_P2P_ATTR_MINOR_REASON, | |
| IEEE80211_P2P_ATTR_CAPABILITY, | |
| IEEE80211_P2P_ATTR_DEVICE_ID, | |
| IEEE80211_P2P_ATTR_GO_INTENT, | |
| IEEE80211_P2P_ATTR_GO_CONFIG_TIMEOUT, | |
| IEEE80211_P2P_ATTR_LISTEN_CHANNEL, | |
| IEEE80211_P2P_ATTR_GROUP_BSSID, | |
| IEEE80211_P2P_ATTR_EXT_LISTEN_TIMING, | |
| IEEE80211_P2P_ATTR_INTENDED_IFACE_ADDR, | |
| IEEE80211_P2P_ATTR_MANAGABILITY, | |
| IEEE80211_P2P_ATTR_CHANNEL_LIST, | |
| IEEE80211_P2P_ATTR_ABSENCE_NOTICE, | |
| IEEE80211_P2P_ATTR_DEVICE_INFO, | |
| IEEE80211_P2P_ATTR_GROUP_INFO, | |
| IEEE80211_P2P_ATTR_GROUP_ID, | |
| IEEE80211_P2P_ATTR_INTERFACE, | |
| IEEE80211_P2P_ATTR_OPER_CHANNEL, | |
| IEEE80211_P2P_ATTR_INVITE_FLAGS, | |
| /* 19 - 220: Reserved */ | |
| IEEE80211_P2P_ATTR_VENDOR_SPECIFIC = 221, | |
| IEEE80211_P2P_ATTR_MAX | |
| }; | |
| /* Notice of Absence attribute - described in P2P spec 4.1.14 */ | |
| /* Typical max value used here */ | |
| #define IEEE80211_P2P_NOA_DESC_MAX 4 | |
| struct ieee80211_p2p_noa_desc { | |
| u8 count; | |
| __le32 duration; | |
| __le32 interval; | |
| __le32 start_time; | |
| } __packed; | |
| struct ieee80211_p2p_noa_attr { | |
| u8 index; | |
| u8 oppps_ctwindow; | |
| struct ieee80211_p2p_noa_desc desc[IEEE80211_P2P_NOA_DESC_MAX]; | |
| } __packed; | |
| #define IEEE80211_P2P_OPPPS_ENABLE_BIT BIT(7) | |
| #define IEEE80211_P2P_OPPPS_CTWINDOW_MASK 0x7F | |
| /** | |
| * struct ieee80211_bar - HT Block Ack Request | |
| * | |
| * This structure refers to "HT BlockAckReq" as | |
| * described in 802.11n draft section 7.2.1.7.1 | |
| */ | |
| struct ieee80211_bar { | |
| __le16 frame_control; | |
| __le16 duration; | |
| __u8 ra[ETH_ALEN]; | |
| __u8 ta[ETH_ALEN]; | |
| __le16 control; | |
| __le16 start_seq_num; | |
| } __packed; | |
| /* 802.11 BAR control masks */ | |
| #define IEEE80211_BAR_CTRL_ACK_POLICY_NORMAL 0x0000 | |
| #define IEEE80211_BAR_CTRL_MULTI_TID 0x0002 | |
| #define IEEE80211_BAR_CTRL_CBMTID_COMPRESSED_BA 0x0004 | |
| #define IEEE80211_BAR_CTRL_TID_INFO_MASK 0xf000 | |
| #define IEEE80211_BAR_CTRL_TID_INFO_SHIFT 12 | |
| #define IEEE80211_HT_MCS_MASK_LEN 10 | |
| /** | |
| * struct ieee80211_mcs_info - MCS information | |
| * @rx_mask: RX mask | |
| * @rx_highest: highest supported RX rate. If set represents | |
| * the highest supported RX data rate in units of 1 Mbps. | |
| * If this field is 0 this value should not be used to | |
| * consider the highest RX data rate supported. | |
| * @tx_params: TX parameters | |
| */ | |
| struct ieee80211_mcs_info { | |
| u8 rx_mask[IEEE80211_HT_MCS_MASK_LEN]; | |
| __le16 rx_highest; | |
| u8 tx_params; | |
| u8 reserved[3]; | |
| } __packed; | |
| /* 802.11n HT capability MSC set */ | |
| #define IEEE80211_HT_MCS_RX_HIGHEST_MASK 0x3ff | |
| #define IEEE80211_HT_MCS_TX_DEFINED 0x01 | |
| #define IEEE80211_HT_MCS_TX_RX_DIFF 0x02 | |
| /* value 0 == 1 stream etc */ | |
| #define IEEE80211_HT_MCS_TX_MAX_STREAMS_MASK 0x0C | |
| #define IEEE80211_HT_MCS_TX_MAX_STREAMS_SHIFT 2 | |
| #define IEEE80211_HT_MCS_TX_MAX_STREAMS 4 | |
| #define IEEE80211_HT_MCS_TX_UNEQUAL_MODULATION 0x10 | |
| /* | |
| * 802.11n D5.0 20.3.5 / 20.6 says: | |
| * - indices 0 to 7 and 32 are single spatial stream | |
| * - 8 to 31 are multiple spatial streams using equal modulation | |
| * [8..15 for two streams, 16..23 for three and 24..31 for four] | |
| * - remainder are multiple spatial streams using unequal modulation | |
| */ | |
| #define IEEE80211_HT_MCS_UNEQUAL_MODULATION_START 33 | |
| #define IEEE80211_HT_MCS_UNEQUAL_MODULATION_START_BYTE \ | |
| (IEEE80211_HT_MCS_UNEQUAL_MODULATION_START / 8) | |
| /** | |
| * struct ieee80211_ht_cap - HT capabilities | |
| * | |
| * This structure is the "HT capabilities element" as | |
| * described in 802.11n D5.0 7.3.2.57 | |
| */ | |
| struct ieee80211_ht_cap { | |
| __le16 cap_info; | |
| u8 ampdu_params_info; | |
| /* 16 bytes MCS information */ | |
| struct ieee80211_mcs_info mcs; | |
| __le16 extended_ht_cap_info; | |
| __le32 tx_BF_cap_info; | |
| u8 antenna_selection_info; | |
| } __packed; | |
| /* 802.11n HT capabilities masks (for cap_info) */ | |
| #define IEEE80211_HT_CAP_LDPC_CODING 0x0001 | |
| #define IEEE80211_HT_CAP_SUP_WIDTH_20_40 0x0002 | |
| #define IEEE80211_HT_CAP_SM_PS 0x000C | |
| #define IEEE80211_HT_CAP_SM_PS_SHIFT 2 | |
| #define IEEE80211_HT_CAP_GRN_FLD 0x0010 | |
| #define IEEE80211_HT_CAP_SGI_20 0x0020 | |
| #define IEEE80211_HT_CAP_SGI_40 0x0040 | |
| #define IEEE80211_HT_CAP_TX_STBC 0x0080 | |
| #define IEEE80211_HT_CAP_RX_STBC 0x0300 | |
| #define IEEE80211_HT_CAP_RX_STBC_SHIFT 8 | |
| #define IEEE80211_HT_CAP_DELAY_BA 0x0400 | |
| #define IEEE80211_HT_CAP_MAX_AMSDU 0x0800 | |
| #define IEEE80211_HT_CAP_DSSSCCK40 0x1000 | |
| #define IEEE80211_HT_CAP_RESERVED 0x2000 | |
| #define IEEE80211_HT_CAP_40MHZ_INTOLERANT 0x4000 | |
| #define IEEE80211_HT_CAP_LSIG_TXOP_PROT 0x8000 | |
| /* 802.11n HT extended capabilities masks (for extended_ht_cap_info) */ | |
| #define IEEE80211_HT_EXT_CAP_PCO 0x0001 | |
| #define IEEE80211_HT_EXT_CAP_PCO_TIME 0x0006 | |
| #define IEEE80211_HT_EXT_CAP_PCO_TIME_SHIFT 1 | |
| #define IEEE80211_HT_EXT_CAP_MCS_FB 0x0300 | |
| #define IEEE80211_HT_EXT_CAP_MCS_FB_SHIFT 8 | |
| #define IEEE80211_HT_EXT_CAP_HTC_SUP 0x0400 | |
| #define IEEE80211_HT_EXT_CAP_RD_RESPONDER 0x0800 | |
| /* 802.11n HT capability AMPDU settings (for ampdu_params_info) */ | |
| #define IEEE80211_HT_AMPDU_PARM_FACTOR 0x03 | |
| #define IEEE80211_HT_AMPDU_PARM_DENSITY 0x1C | |
| #define IEEE80211_HT_AMPDU_PARM_DENSITY_SHIFT 2 | |
| /* | |
| * Maximum length of AMPDU that the STA can receive in high-throughput (HT). | |
| * Length = 2 ^ (13 + max_ampdu_length_exp) - 1 (octets) | |
| */ | |
| enum ieee80211_max_ampdu_length_exp { | |
| IEEE80211_HT_MAX_AMPDU_8K = 0, | |
| IEEE80211_HT_MAX_AMPDU_16K = 1, | |
| IEEE80211_HT_MAX_AMPDU_32K = 2, | |
| IEEE80211_HT_MAX_AMPDU_64K = 3 | |
| }; | |
| /* | |
| * Maximum length of AMPDU that the STA can receive in VHT. | |
| * Length = 2 ^ (13 + max_ampdu_length_exp) - 1 (octets) | |
| */ | |
| enum ieee80211_vht_max_ampdu_length_exp { | |
| IEEE80211_VHT_MAX_AMPDU_8K = 0, | |
| IEEE80211_VHT_MAX_AMPDU_16K = 1, | |
| IEEE80211_VHT_MAX_AMPDU_32K = 2, | |
| IEEE80211_VHT_MAX_AMPDU_64K = 3, | |
| IEEE80211_VHT_MAX_AMPDU_128K = 4, | |
| IEEE80211_VHT_MAX_AMPDU_256K = 5, | |
| IEEE80211_VHT_MAX_AMPDU_512K = 6, | |
| IEEE80211_VHT_MAX_AMPDU_1024K = 7 | |
| }; | |
| #define IEEE80211_HT_MAX_AMPDU_FACTOR 13 | |
| /* Minimum MPDU start spacing */ | |
| enum ieee80211_min_mpdu_spacing { | |
| IEEE80211_HT_MPDU_DENSITY_NONE = 0, /* No restriction */ | |
| IEEE80211_HT_MPDU_DENSITY_0_25 = 1, /* 1/4 usec */ | |
| IEEE80211_HT_MPDU_DENSITY_0_5 = 2, /* 1/2 usec */ | |
| IEEE80211_HT_MPDU_DENSITY_1 = 3, /* 1 usec */ | |
| IEEE80211_HT_MPDU_DENSITY_2 = 4, /* 2 usec */ | |
| IEEE80211_HT_MPDU_DENSITY_4 = 5, /* 4 usec */ | |
| IEEE80211_HT_MPDU_DENSITY_8 = 6, /* 8 usec */ | |
| IEEE80211_HT_MPDU_DENSITY_16 = 7 /* 16 usec */ | |
| }; | |
| /** | |
| * struct ieee80211_ht_operation - HT operation IE | |
| * | |
| * This structure is the "HT operation element" as | |
| * described in 802.11n-2009 7.3.2.57 | |
| */ | |
| struct ieee80211_ht_operation { | |
| u8 primary_chan; | |
| u8 ht_param; | |
| __le16 operation_mode; | |
| __le16 stbc_param; | |
| u8 basic_set[16]; | |
| } __packed; | |
| /* for ht_param */ | |
| #define IEEE80211_HT_PARAM_CHA_SEC_OFFSET 0x03 | |
| #define IEEE80211_HT_PARAM_CHA_SEC_NONE 0x00 | |
| #define IEEE80211_HT_PARAM_CHA_SEC_ABOVE 0x01 | |
| #define IEEE80211_HT_PARAM_CHA_SEC_BELOW 0x03 | |
| #define IEEE80211_HT_PARAM_CHAN_WIDTH_ANY 0x04 | |
| #define IEEE80211_HT_PARAM_RIFS_MODE 0x08 | |
| /* for operation_mode */ | |
| #define IEEE80211_HT_OP_MODE_PROTECTION 0x0003 | |
| #define IEEE80211_HT_OP_MODE_PROTECTION_NONE 0 | |
| #define IEEE80211_HT_OP_MODE_PROTECTION_NONMEMBER 1 | |
| #define IEEE80211_HT_OP_MODE_PROTECTION_20MHZ 2 | |
| #define IEEE80211_HT_OP_MODE_PROTECTION_NONHT_MIXED 3 | |
| #define IEEE80211_HT_OP_MODE_NON_GF_STA_PRSNT 0x0004 | |
| #define IEEE80211_HT_OP_MODE_NON_HT_STA_PRSNT 0x0010 | |
| #define IEEE80211_HT_OP_MODE_CCFS2_SHIFT 5 | |
| #define IEEE80211_HT_OP_MODE_CCFS2_MASK 0x1fe0 | |
| /* for stbc_param */ | |
| #define IEEE80211_HT_STBC_PARAM_DUAL_BEACON 0x0040 | |
| #define IEEE80211_HT_STBC_PARAM_DUAL_CTS_PROT 0x0080 | |
| #define IEEE80211_HT_STBC_PARAM_STBC_BEACON 0x0100 | |
| #define IEEE80211_HT_STBC_PARAM_LSIG_TXOP_FULLPROT 0x0200 | |
| #define IEEE80211_HT_STBC_PARAM_PCO_ACTIVE 0x0400 | |
| #define IEEE80211_HT_STBC_PARAM_PCO_PHASE 0x0800 | |
| /* block-ack parameters */ | |
| #define IEEE80211_ADDBA_PARAM_AMSDU_MASK 0x0001 | |
| #define IEEE80211_ADDBA_PARAM_POLICY_MASK 0x0002 | |
| #define IEEE80211_ADDBA_PARAM_TID_MASK 0x003C | |
| #define IEEE80211_ADDBA_PARAM_BUF_SIZE_MASK 0xFFC0 | |
| #define IEEE80211_DELBA_PARAM_TID_MASK 0xF000 | |
| #define IEEE80211_DELBA_PARAM_INITIATOR_MASK 0x0800 | |
| /* | |
| * A-MPDU buffer sizes | |
| * According to HT size varies from 8 to 64 frames | |
| * HE adds the ability to have up to 256 frames. | |
| */ | |
| #define IEEE80211_MIN_AMPDU_BUF 0x8 | |
| #define IEEE80211_MAX_AMPDU_BUF_HT 0x40 | |
| #define IEEE80211_MAX_AMPDU_BUF 0x100 | |
| /* Spatial Multiplexing Power Save Modes (for capability) */ | |
| #define WLAN_HT_CAP_SM_PS_STATIC 0 | |
| #define WLAN_HT_CAP_SM_PS_DYNAMIC 1 | |
| #define WLAN_HT_CAP_SM_PS_INVALID 2 | |
| #define WLAN_HT_CAP_SM_PS_DISABLED 3 | |
| /* for SM power control field lower two bits */ | |
| #define WLAN_HT_SMPS_CONTROL_DISABLED 0 | |
| #define WLAN_HT_SMPS_CONTROL_STATIC 1 | |
| #define WLAN_HT_SMPS_CONTROL_DYNAMIC 3 | |
| /** | |
| * struct ieee80211_vht_mcs_info - VHT MCS information | |
| * @rx_mcs_map: RX MCS map 2 bits for each stream, total 8 streams | |
| * @rx_highest: Indicates highest long GI VHT PPDU data rate | |
| * STA can receive. Rate expressed in units of 1 Mbps. | |
| * If this field is 0 this value should not be used to | |
| * consider the highest RX data rate supported. | |
| * The top 3 bits of this field indicate the Maximum NSTS,total | |
| * (a beamformee capability.) | |
| * @tx_mcs_map: TX MCS map 2 bits for each stream, total 8 streams | |
| * @tx_highest: Indicates highest long GI VHT PPDU data rate | |
| * STA can transmit. Rate expressed in units of 1 Mbps. | |
| * If this field is 0 this value should not be used to | |
| * consider the highest TX data rate supported. | |
| * The top 2 bits of this field are reserved, the | |
| * 3rd bit from the top indiciates VHT Extended NSS BW | |
| * Capability. | |
| */ | |
| struct ieee80211_vht_mcs_info { | |
| __le16 rx_mcs_map; | |
| __le16 rx_highest; | |
| __le16 tx_mcs_map; | |
| __le16 tx_highest; | |
| } __packed; | |
| /* for rx_highest */ | |
| #define IEEE80211_VHT_MAX_NSTS_TOTAL_SHIFT 13 | |
| #define IEEE80211_VHT_MAX_NSTS_TOTAL_MASK (7 << IEEE80211_VHT_MAX_NSTS_TOTAL_SHIFT) | |
| /* for tx_highest */ | |
| #define IEEE80211_VHT_EXT_NSS_BW_CAPABLE (1 << 13) | |
| /** | |
| * enum ieee80211_vht_mcs_support - VHT MCS support definitions | |
| * @IEEE80211_VHT_MCS_SUPPORT_0_7: MCSes 0-7 are supported for the | |
| * number of streams | |
| * @IEEE80211_VHT_MCS_SUPPORT_0_8: MCSes 0-8 are supported | |
| * @IEEE80211_VHT_MCS_SUPPORT_0_9: MCSes 0-9 are supported | |
| * @IEEE80211_VHT_MCS_NOT_SUPPORTED: This number of streams isn't supported | |
| * | |
| * These definitions are used in each 2-bit subfield of the @rx_mcs_map | |
| * and @tx_mcs_map fields of &struct ieee80211_vht_mcs_info, which are | |
| * both split into 8 subfields by number of streams. These values indicate | |
| * which MCSes are supported for the number of streams the value appears | |
| * for. | |
| */ | |
| enum ieee80211_vht_mcs_support { | |
| IEEE80211_VHT_MCS_SUPPORT_0_7 = 0, | |
| IEEE80211_VHT_MCS_SUPPORT_0_8 = 1, | |
| IEEE80211_VHT_MCS_SUPPORT_0_9 = 2, | |
| IEEE80211_VHT_MCS_NOT_SUPPORTED = 3, | |
| }; | |
| /** | |
| * struct ieee80211_vht_cap - VHT capabilities | |
| * | |
| * This structure is the "VHT capabilities element" as | |
| * described in 802.11ac D3.0 8.4.2.160 | |
| * @vht_cap_info: VHT capability info | |
| * @supp_mcs: VHT MCS supported rates | |
| */ | |
| struct ieee80211_vht_cap { | |
| __le32 vht_cap_info; | |
| struct ieee80211_vht_mcs_info supp_mcs; | |
| } __packed; | |
| /** | |
| * enum ieee80211_vht_chanwidth - VHT channel width | |
| * @IEEE80211_VHT_CHANWIDTH_USE_HT: use the HT operation IE to | |
| * determine the channel width (20 or 40 MHz) | |
| * @IEEE80211_VHT_CHANWIDTH_80MHZ: 80 MHz bandwidth | |
| * @IEEE80211_VHT_CHANWIDTH_160MHZ: 160 MHz bandwidth | |
| * @IEEE80211_VHT_CHANWIDTH_80P80MHZ: 80+80 MHz bandwidth | |
| */ | |
| enum ieee80211_vht_chanwidth { | |
| IEEE80211_VHT_CHANWIDTH_USE_HT = 0, | |
| IEEE80211_VHT_CHANWIDTH_80MHZ = 1, | |
| IEEE80211_VHT_CHANWIDTH_160MHZ = 2, | |
| IEEE80211_VHT_CHANWIDTH_80P80MHZ = 3, | |
| }; | |
| /** | |
| * struct ieee80211_vht_operation - VHT operation IE | |
| * | |
| * This structure is the "VHT operation element" as | |
| * described in 802.11ac D3.0 8.4.2.161 | |
| * @chan_width: Operating channel width | |
| * @center_freq_seg0_idx: center freq segment 0 index | |
| * @center_freq_seg1_idx: center freq segment 1 index | |
| * @basic_mcs_set: VHT Basic MCS rate set | |
| */ | |
| struct ieee80211_vht_operation { | |
| u8 chan_width; | |
| u8 center_freq_seg0_idx; | |
| u8 center_freq_seg1_idx; | |
| __le16 basic_mcs_set; | |
| } __packed; | |
| /** | |
| * struct ieee80211_he_cap_elem - HE capabilities element | |
| * | |
| * This structure is the "HE capabilities element" fixed fields as | |
| * described in P802.11ax_D4.0 section 9.4.2.242.2 and 9.4.2.242.3 | |
| */ | |
| struct ieee80211_he_cap_elem { | |
| u8 mac_cap_info[6]; | |
| u8 phy_cap_info[11]; | |
| } __packed; | |
| #define IEEE80211_TX_RX_MCS_NSS_DESC_MAX_LEN 5 | |
| /** | |
| * enum ieee80211_he_mcs_support - HE MCS support definitions | |
| * @IEEE80211_HE_MCS_SUPPORT_0_7: MCSes 0-7 are supported for the | |
| * number of streams | |
| * @IEEE80211_HE_MCS_SUPPORT_0_9: MCSes 0-9 are supported | |
| * @IEEE80211_HE_MCS_SUPPORT_0_11: MCSes 0-11 are supported | |
| * @IEEE80211_HE_MCS_NOT_SUPPORTED: This number of streams isn't supported | |
| * | |
| * These definitions are used in each 2-bit subfield of the rx_mcs_* | |
| * and tx_mcs_* fields of &struct ieee80211_he_mcs_nss_supp, which are | |
| * both split into 8 subfields by number of streams. These values indicate | |
| * which MCSes are supported for the number of streams the value appears | |
| * for. | |
| */ | |
| enum ieee80211_he_mcs_support { | |
| IEEE80211_HE_MCS_SUPPORT_0_7 = 0, | |
| IEEE80211_HE_MCS_SUPPORT_0_9 = 1, | |
| IEEE80211_HE_MCS_SUPPORT_0_11 = 2, | |
| IEEE80211_HE_MCS_NOT_SUPPORTED = 3, | |
| }; | |
| /** | |
| * struct ieee80211_he_mcs_nss_supp - HE Tx/Rx HE MCS NSS Support Field | |
| * | |
| * This structure holds the data required for the Tx/Rx HE MCS NSS Support Field | |
| * described in P802.11ax_D2.0 section 9.4.2.237.4 | |
| * | |
| * @rx_mcs_80: Rx MCS map 2 bits for each stream, total 8 streams, for channel | |
| * widths less than 80MHz. | |
| * @tx_mcs_80: Tx MCS map 2 bits for each stream, total 8 streams, for channel | |
| * widths less than 80MHz. | |
| * @rx_mcs_160: Rx MCS map 2 bits for each stream, total 8 streams, for channel | |
| * width 160MHz. | |
| * @tx_mcs_160: Tx MCS map 2 bits for each stream, total 8 streams, for channel | |
| * width 160MHz. | |
| * @rx_mcs_80p80: Rx MCS map 2 bits for each stream, total 8 streams, for | |
| * channel width 80p80MHz. | |
| * @tx_mcs_80p80: Tx MCS map 2 bits for each stream, total 8 streams, for | |
| * channel width 80p80MHz. | |
| */ | |
| struct ieee80211_he_mcs_nss_supp { | |
| __le16 rx_mcs_80; | |
| __le16 tx_mcs_80; | |
| __le16 rx_mcs_160; | |
| __le16 tx_mcs_160; | |
| __le16 rx_mcs_80p80; | |
| __le16 tx_mcs_80p80; | |
| } __packed; | |
| /** | |
| * struct ieee80211_he_operation - HE capabilities element | |
| * | |
| * This structure is the "HE operation element" fields as | |
| * described in P802.11ax_D4.0 section 9.4.2.243 | |
| */ | |
| struct ieee80211_he_operation { | |
| __le32 he_oper_params; | |
| __le16 he_mcs_nss_set; | |
| /* Optional 0,1,3,4,5,7 or 8 bytes: depends on @he_oper_params */ | |
| u8 optional[]; | |
| } __packed; | |
| /** | |
| * struct ieee80211_he_spr - HE spatial reuse element | |
| * | |
| * This structure is the "HE spatial reuse element" element as | |
| * described in P802.11ax_D4.0 section 9.4.2.241 | |
| */ | |
| struct ieee80211_he_spr { | |
| u8 he_sr_control; | |
| /* Optional 0 to 19 bytes: depends on @he_sr_control */ | |
| u8 optional[]; | |
| } __packed; | |
| /** | |
| * struct ieee80211_he_mu_edca_param_ac_rec - MU AC Parameter Record field | |
| * | |
| * This structure is the "MU AC Parameter Record" fields as | |
| * described in P802.11ax_D4.0 section 9.4.2.245 | |
| */ | |
| struct ieee80211_he_mu_edca_param_ac_rec { | |
| u8 aifsn; | |
| u8 ecw_min_max; | |
| u8 mu_edca_timer; | |
| } __packed; | |
| /** | |
| * struct ieee80211_mu_edca_param_set - MU EDCA Parameter Set element | |
| * | |
| * This structure is the "MU EDCA Parameter Set element" fields as | |
| * described in P802.11ax_D4.0 section 9.4.2.245 | |
| */ | |
| struct ieee80211_mu_edca_param_set { | |
| u8 mu_qos_info; | |
| struct ieee80211_he_mu_edca_param_ac_rec ac_be; | |
| struct ieee80211_he_mu_edca_param_ac_rec ac_bk; | |
| struct ieee80211_he_mu_edca_param_ac_rec ac_vi; | |
| struct ieee80211_he_mu_edca_param_ac_rec ac_vo; | |
| } __packed; | |
| /* 802.11ac VHT Capabilities */ | |
| #define IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_3895 0x00000000 | |
| #define IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_7991 0x00000001 | |
| #define IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_11454 0x00000002 | |
| #define IEEE80211_VHT_CAP_MAX_MPDU_MASK 0x00000003 | |
| #define IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ 0x00000004 | |
| #define IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ 0x00000008 | |
| #define IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK 0x0000000C | |
| #define IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_SHIFT 2 | |
| #define IEEE80211_VHT_CAP_RXLDPC 0x00000010 | |
| #define IEEE80211_VHT_CAP_SHORT_GI_80 0x00000020 | |
| #define IEEE80211_VHT_CAP_SHORT_GI_160 0x00000040 | |
| #define IEEE80211_VHT_CAP_TXSTBC 0x00000080 | |
| #define IEEE80211_VHT_CAP_RXSTBC_1 0x00000100 | |
| #define IEEE80211_VHT_CAP_RXSTBC_2 0x00000200 | |
| #define IEEE80211_VHT_CAP_RXSTBC_3 0x00000300 | |
| #define IEEE80211_VHT_CAP_RXSTBC_4 0x00000400 | |
| #define IEEE80211_VHT_CAP_RXSTBC_MASK 0x00000700 | |
| #define IEEE80211_VHT_CAP_RXSTBC_SHIFT 8 | |
| #define IEEE80211_VHT_CAP_SU_BEAMFORMER_CAPABLE 0x00000800 | |
| #define IEEE80211_VHT_CAP_SU_BEAMFORMEE_CAPABLE 0x00001000 | |
| #define IEEE80211_VHT_CAP_BEAMFORMEE_STS_SHIFT 13 | |
| #define IEEE80211_VHT_CAP_BEAMFORMEE_STS_MASK \ | |
| (7 << IEEE80211_VHT_CAP_BEAMFORMEE_STS_SHIFT) | |
| #define IEEE80211_VHT_CAP_SOUNDING_DIMENSIONS_SHIFT 16 | |
| #define IEEE80211_VHT_CAP_SOUNDING_DIMENSIONS_MASK \ | |
| (7 << IEEE80211_VHT_CAP_SOUNDING_DIMENSIONS_SHIFT) | |
| #define IEEE80211_VHT_CAP_MU_BEAMFORMER_CAPABLE 0x00080000 | |
| #define IEEE80211_VHT_CAP_MU_BEAMFORMEE_CAPABLE 0x00100000 | |
| #define IEEE80211_VHT_CAP_VHT_TXOP_PS 0x00200000 | |
| #define IEEE80211_VHT_CAP_HTC_VHT 0x00400000 | |
| #define IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_SHIFT 23 | |
| #define IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_MASK \ | |
| (7 << IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_SHIFT) | |
| #define IEEE80211_VHT_CAP_VHT_LINK_ADAPTATION_VHT_UNSOL_MFB 0x08000000 | |
| #define IEEE80211_VHT_CAP_VHT_LINK_ADAPTATION_VHT_MRQ_MFB 0x0c000000 | |
| #define IEEE80211_VHT_CAP_RX_ANTENNA_PATTERN 0x10000000 | |
| #define IEEE80211_VHT_CAP_TX_ANTENNA_PATTERN 0x20000000 | |
| #define IEEE80211_VHT_CAP_EXT_NSS_BW_SHIFT 30 | |
| #define IEEE80211_VHT_CAP_EXT_NSS_BW_MASK 0xc0000000 | |
| /** | |
| * ieee80211_get_vht_max_nss - return max NSS for a given bandwidth/MCS | |
| * @cap: VHT capabilities of the peer | |
| * @bw: bandwidth to use | |
| * @mcs: MCS index to use | |
| * @ext_nss_bw_capable: indicates whether or not the local transmitter | |
| * (rate scaling algorithm) can deal with the new logic | |
| * (dot11VHTExtendedNSSBWCapable) | |
| * @max_vht_nss: current maximum NSS as advertised by the STA in | |
| * operating mode notification, can be 0 in which case the | |
| * capability data will be used to derive this (from MCS support) | |
| * | |
| * Due to the VHT Extended NSS Bandwidth Support, the maximum NSS can | |
| * vary for a given BW/MCS. This function parses the data. | |
| * | |
| * Note: This function is exported by cfg80211. | |
| */ | |
| int ieee80211_get_vht_max_nss(struct ieee80211_vht_cap *cap, | |
| enum ieee80211_vht_chanwidth bw, | |
| int mcs, bool ext_nss_bw_capable, | |
| unsigned int max_vht_nss); | |
| /* 802.11ax HE MAC capabilities */ | |
| #define IEEE80211_HE_MAC_CAP0_HTC_HE 0x01 | |
| #define IEEE80211_HE_MAC_CAP0_TWT_REQ 0x02 | |
| #define IEEE80211_HE_MAC_CAP0_TWT_RES 0x04 | |
| #define IEEE80211_HE_MAC_CAP0_DYNAMIC_FRAG_NOT_SUPP 0x00 | |
| #define IEEE80211_HE_MAC_CAP0_DYNAMIC_FRAG_LEVEL_1 0x08 | |
| #define IEEE80211_HE_MAC_CAP0_DYNAMIC_FRAG_LEVEL_2 0x10 | |
| #define IEEE80211_HE_MAC_CAP0_DYNAMIC_FRAG_LEVEL_3 0x18 | |
| #define IEEE80211_HE_MAC_CAP0_DYNAMIC_FRAG_MASK 0x18 | |
| #define IEEE80211_HE_MAC_CAP0_MAX_NUM_FRAG_MSDU_1 0x00 | |
| #define IEEE80211_HE_MAC_CAP0_MAX_NUM_FRAG_MSDU_2 0x20 | |
| #define IEEE80211_HE_MAC_CAP0_MAX_NUM_FRAG_MSDU_4 0x40 | |
| #define IEEE80211_HE_MAC_CAP0_MAX_NUM_FRAG_MSDU_8 0x60 | |
| #define IEEE80211_HE_MAC_CAP0_MAX_NUM_FRAG_MSDU_16 0x80 | |
| #define IEEE80211_HE_MAC_CAP0_MAX_NUM_FRAG_MSDU_32 0xa0 | |
| #define IEEE80211_HE_MAC_CAP0_MAX_NUM_FRAG_MSDU_64 0xc0 | |
| #define IEEE80211_HE_MAC_CAP0_MAX_NUM_FRAG_MSDU_UNLIMITED 0xe0 | |
| #define IEEE80211_HE_MAC_CAP0_MAX_NUM_FRAG_MSDU_MASK 0xe0 | |
| #define IEEE80211_HE_MAC_CAP1_MIN_FRAG_SIZE_UNLIMITED 0x00 | |
| #define IEEE80211_HE_MAC_CAP1_MIN_FRAG_SIZE_128 0x01 | |
| #define IEEE80211_HE_MAC_CAP1_MIN_FRAG_SIZE_256 0x02 | |
| #define IEEE80211_HE_MAC_CAP1_MIN_FRAG_SIZE_512 0x03 | |
| #define IEEE80211_HE_MAC_CAP1_MIN_FRAG_SIZE_MASK 0x03 | |
| #define IEEE80211_HE_MAC_CAP1_TF_MAC_PAD_DUR_0US 0x00 | |
| #define IEEE80211_HE_MAC_CAP1_TF_MAC_PAD_DUR_8US 0x04 | |
| #define IEEE80211_HE_MAC_CAP1_TF_MAC_PAD_DUR_16US 0x08 | |
| #define IEEE80211_HE_MAC_CAP1_TF_MAC_PAD_DUR_MASK 0x0c | |
| #define IEEE80211_HE_MAC_CAP1_MULTI_TID_AGG_RX_QOS_1 0x00 | |
| #define IEEE80211_HE_MAC_CAP1_MULTI_TID_AGG_RX_QOS_2 0x10 | |
| #define IEEE80211_HE_MAC_CAP1_MULTI_TID_AGG_RX_QOS_3 0x20 | |
| #define IEEE80211_HE_MAC_CAP1_MULTI_TID_AGG_RX_QOS_4 0x30 | |
| #define IEEE80211_HE_MAC_CAP1_MULTI_TID_AGG_RX_QOS_5 0x40 | |
| #define IEEE80211_HE_MAC_CAP1_MULTI_TID_AGG_RX_QOS_6 0x50 | |
| #define IEEE80211_HE_MAC_CAP1_MULTI_TID_AGG_RX_QOS_7 0x60 | |
| #define IEEE80211_HE_MAC_CAP1_MULTI_TID_AGG_RX_QOS_8 0x70 | |
| #define IEEE80211_HE_MAC_CAP1_MULTI_TID_AGG_RX_QOS_MASK 0x70 | |
| /* Link adaptation is split between byte HE_MAC_CAP1 and | |
| * HE_MAC_CAP2. It should be set only if IEEE80211_HE_MAC_CAP0_HTC_HE | |
| * in which case the following values apply: | |
| * 0 = No feedback. | |
| * 1 = reserved. | |
| * 2 = Unsolicited feedback. | |
| * 3 = both | |
| */ | |
| #define IEEE80211_HE_MAC_CAP1_LINK_ADAPTATION 0x80 | |
| #define IEEE80211_HE_MAC_CAP2_LINK_ADAPTATION 0x01 | |
| #define IEEE80211_HE_MAC_CAP2_ALL_ACK 0x02 | |
| #define IEEE80211_HE_MAC_CAP2_TRS 0x04 | |
| #define IEEE80211_HE_MAC_CAP2_BSR 0x08 | |
| #define IEEE80211_HE_MAC_CAP2_BCAST_TWT 0x10 | |
| #define IEEE80211_HE_MAC_CAP2_32BIT_BA_BITMAP 0x20 | |
| #define IEEE80211_HE_MAC_CAP2_MU_CASCADING 0x40 | |
| #define IEEE80211_HE_MAC_CAP2_ACK_EN 0x80 | |
| #define IEEE80211_HE_MAC_CAP3_OMI_CONTROL 0x02 | |
| #define IEEE80211_HE_MAC_CAP3_OFDMA_RA 0x04 | |
| /* The maximum length of an A-MDPU is defined by the combination of the Maximum | |
| * A-MDPU Length Exponent field in the HT capabilities, VHT capabilities and the | |
| * same field in the HE capabilities. | |
| */ | |
| #define IEEE80211_HE_MAC_CAP3_MAX_AMPDU_LEN_EXP_USE_VHT 0x00 | |
| #define IEEE80211_HE_MAC_CAP3_MAX_AMPDU_LEN_EXP_VHT_1 0x08 | |
| #define IEEE80211_HE_MAC_CAP3_MAX_AMPDU_LEN_EXP_VHT_2 0x10 | |
| #define IEEE80211_HE_MAC_CAP3_MAX_AMPDU_LEN_EXP_RESERVED 0x18 | |
| #define IEEE80211_HE_MAC_CAP3_MAX_AMPDU_LEN_EXP_MASK 0x18 | |
| #define IEEE80211_HE_MAC_CAP3_AMSDU_FRAG 0x20 | |
| #define IEEE80211_HE_MAC_CAP3_FLEX_TWT_SCHED 0x40 | |
| #define IEEE80211_HE_MAC_CAP3_RX_CTRL_FRAME_TO_MULTIBSS 0x80 | |
| #define IEEE80211_HE_MAC_CAP3_MAX_AMPDU_LEN_EXP_SHIFT 3 | |
| #define IEEE80211_HE_MAC_CAP4_BSRP_BQRP_A_MPDU_AGG 0x01 | |
| #define IEEE80211_HE_MAC_CAP4_QTP 0x02 | |
| #define IEEE80211_HE_MAC_CAP4_BQR 0x04 | |
| #define IEEE80211_HE_MAC_CAP4_SRP_RESP 0x08 | |
| #define IEEE80211_HE_MAC_CAP4_NDP_FB_REP 0x10 | |
| #define IEEE80211_HE_MAC_CAP4_OPS 0x20 | |
| #define IEEE80211_HE_MAC_CAP4_AMDSU_IN_AMPDU 0x40 | |
| /* Multi TID agg TX is split between byte #4 and #5 | |
| * The value is a combination of B39,B40,B41 | |
| */ | |
| #define IEEE80211_HE_MAC_CAP4_MULTI_TID_AGG_TX_QOS_B39 0x80 | |
| #define IEEE80211_HE_MAC_CAP5_MULTI_TID_AGG_TX_QOS_B40 0x01 | |
| #define IEEE80211_HE_MAC_CAP5_MULTI_TID_AGG_TX_QOS_B41 0x02 | |
| #define IEEE80211_HE_MAC_CAP5_SUBCHAN_SELECVITE_TRANSMISSION 0x04 | |
| #define IEEE80211_HE_MAC_CAP5_UL_2x996_TONE_RU 0x08 | |
| #define IEEE80211_HE_MAC_CAP5_OM_CTRL_UL_MU_DATA_DIS_RX 0x10 | |
| #define IEEE80211_HE_MAC_CAP5_HE_DYNAMIC_SM_PS 0x20 | |
| #define IEEE80211_HE_MAC_CAP5_PUNCTURED_SOUNDING 0x40 | |
| #define IEEE80211_HE_MAC_CAP5_HT_VHT_TRIG_FRAME_RX 0x80 | |
| #define IEEE80211_HE_VHT_MAX_AMPDU_FACTOR 20 | |
| #define IEEE80211_HE_HT_MAX_AMPDU_FACTOR 16 | |
| /* 802.11ax HE PHY capabilities */ | |
| #define IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_40MHZ_IN_2G 0x02 | |
| #define IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_40MHZ_80MHZ_IN_5G 0x04 | |
| #define IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_160MHZ_IN_5G 0x08 | |
| #define IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_80PLUS80_MHZ_IN_5G 0x10 | |
| #define IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_RU_MAPPING_IN_2G 0x20 | |
| #define IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_RU_MAPPING_IN_5G 0x40 | |
| #define IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_MASK 0xfe | |
| #define IEEE80211_HE_PHY_CAP1_PREAMBLE_PUNC_RX_80MHZ_ONLY_SECOND_20MHZ 0x01 | |
| #define IEEE80211_HE_PHY_CAP1_PREAMBLE_PUNC_RX_80MHZ_ONLY_SECOND_40MHZ 0x02 | |
| #define IEEE80211_HE_PHY_CAP1_PREAMBLE_PUNC_RX_160MHZ_ONLY_SECOND_20MHZ 0x04 | |
| #define IEEE80211_HE_PHY_CAP1_PREAMBLE_PUNC_RX_160MHZ_ONLY_SECOND_40MHZ 0x08 | |
| #define IEEE80211_HE_PHY_CAP1_PREAMBLE_PUNC_RX_MASK 0x0f | |
| #define IEEE80211_HE_PHY_CAP1_DEVICE_CLASS_A 0x10 | |
| #define IEEE80211_HE_PHY_CAP1_LDPC_CODING_IN_PAYLOAD 0x20 | |
| #define IEEE80211_HE_PHY_CAP1_HE_LTF_AND_GI_FOR_HE_PPDUS_0_8US 0x40 | |
| /* Midamble RX/TX Max NSTS is split between byte #2 and byte #3 */ | |
| #define IEEE80211_HE_PHY_CAP1_MIDAMBLE_RX_TX_MAX_NSTS 0x80 | |
| #define IEEE80211_HE_PHY_CAP2_MIDAMBLE_RX_TX_MAX_NSTS 0x01 | |
| #define IEEE80211_HE_PHY_CAP2_NDP_4x_LTF_AND_3_2US 0x02 | |
| #define IEEE80211_HE_PHY_CAP2_STBC_TX_UNDER_80MHZ 0x04 | |
| #define IEEE80211_HE_PHY_CAP2_STBC_RX_UNDER_80MHZ 0x08 | |
| #define IEEE80211_HE_PHY_CAP2_DOPPLER_TX 0x10 | |
| #define IEEE80211_HE_PHY_CAP2_DOPPLER_RX 0x20 | |
| /* Note that the meaning of UL MU below is different between an AP and a non-AP | |
| * sta, where in the AP case it indicates support for Rx and in the non-AP sta | |
| * case it indicates support for Tx. | |
| */ | |
| #define IEEE80211_HE_PHY_CAP2_UL_MU_FULL_MU_MIMO 0x40 | |
| #define IEEE80211_HE_PHY_CAP2_UL_MU_PARTIAL_MU_MIMO 0x80 | |
| #define IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_TX_NO_DCM 0x00 | |
| #define IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_TX_BPSK 0x01 | |
| #define IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_TX_QPSK 0x02 | |
| #define IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_TX_16_QAM 0x03 | |
| #define IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_TX_MASK 0x03 | |
| #define IEEE80211_HE_PHY_CAP3_DCM_MAX_TX_NSS_1 0x00 | |
| #define IEEE80211_HE_PHY_CAP3_DCM_MAX_TX_NSS_2 0x04 | |
| #define IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_RX_NO_DCM 0x00 | |
| #define IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_RX_BPSK 0x08 | |
| #define IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_RX_QPSK 0x10 | |
| #define IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_RX_16_QAM 0x18 | |
| #define IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_RX_MASK 0x18 | |
| #define IEEE80211_HE_PHY_CAP3_DCM_MAX_RX_NSS_1 0x00 | |
| #define IEEE80211_HE_PHY_CAP3_DCM_MAX_RX_NSS_2 0x20 | |
| #define IEEE80211_HE_PHY_CAP3_RX_HE_MU_PPDU_FROM_NON_AP_STA 0x40 | |
| #define IEEE80211_HE_PHY_CAP3_SU_BEAMFORMER 0x80 | |
| #define IEEE80211_HE_PHY_CAP4_SU_BEAMFORMEE 0x01 | |
| #define IEEE80211_HE_PHY_CAP4_MU_BEAMFORMER 0x02 | |
| /* Minimal allowed value of Max STS under 80MHz is 3 */ | |
| #define IEEE80211_HE_PHY_CAP4_BEAMFORMEE_MAX_STS_UNDER_80MHZ_4 0x0c | |
| #define IEEE80211_HE_PHY_CAP4_BEAMFORMEE_MAX_STS_UNDER_80MHZ_5 0x10 | |
| #define IEEE80211_HE_PHY_CAP4_BEAMFORMEE_MAX_STS_UNDER_80MHZ_6 0x14 | |
| #define IEEE80211_HE_PHY_CAP4_BEAMFORMEE_MAX_STS_UNDER_80MHZ_7 0x18 | |
| #define IEEE80211_HE_PHY_CAP4_BEAMFORMEE_MAX_STS_UNDER_80MHZ_8 0x1c | |
| #define IEEE80211_HE_PHY_CAP4_BEAMFORMEE_MAX_STS_UNDER_80MHZ_MASK 0x1c | |
| /* Minimal allowed value of Max STS above 80MHz is 3 */ | |
| #define IEEE80211_HE_PHY_CAP4_BEAMFORMEE_MAX_STS_ABOVE_80MHZ_4 0x60 | |
| #define IEEE80211_HE_PHY_CAP4_BEAMFORMEE_MAX_STS_ABOVE_80MHZ_5 0x80 | |
| #define IEEE80211_HE_PHY_CAP4_BEAMFORMEE_MAX_STS_ABOVE_80MHZ_6 0xa0 | |
| #define IEEE80211_HE_PHY_CAP4_BEAMFORMEE_MAX_STS_ABOVE_80MHZ_7 0xc0 | |
| #define IEEE80211_HE_PHY_CAP4_BEAMFORMEE_MAX_STS_ABOVE_80MHZ_8 0xe0 | |
| #define IEEE80211_HE_PHY_CAP4_BEAMFORMEE_MAX_STS_ABOVE_80MHZ_MASK 0xe0 | |
| #define IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_UNDER_80MHZ_1 0x00 | |
| #define IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_UNDER_80MHZ_2 0x01 | |
| #define IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_UNDER_80MHZ_3 0x02 | |
| #define IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_UNDER_80MHZ_4 0x03 | |
| #define IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_UNDER_80MHZ_5 0x04 | |
| #define IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_UNDER_80MHZ_6 0x05 | |
| #define IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_UNDER_80MHZ_7 0x06 | |
| #define IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_UNDER_80MHZ_8 0x07 | |
| #define IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_UNDER_80MHZ_MASK 0x07 | |
| #define IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_ABOVE_80MHZ_1 0x00 | |
| #define IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_ABOVE_80MHZ_2 0x08 | |
| #define IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_ABOVE_80MHZ_3 0x10 | |
| #define IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_ABOVE_80MHZ_4 0x18 | |
| #define IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_ABOVE_80MHZ_5 0x20 | |
| #define IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_ABOVE_80MHZ_6 0x28 | |
| #define IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_ABOVE_80MHZ_7 0x30 | |
| #define IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_ABOVE_80MHZ_8 0x38 | |
| #define IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_ABOVE_80MHZ_MASK 0x38 | |
| #define IEEE80211_HE_PHY_CAP5_NG16_SU_FEEDBACK 0x40 | |
| #define IEEE80211_HE_PHY_CAP5_NG16_MU_FEEDBACK 0x80 | |
| #define IEEE80211_HE_PHY_CAP6_CODEBOOK_SIZE_42_SU 0x01 | |
| #define IEEE80211_HE_PHY_CAP6_CODEBOOK_SIZE_75_MU 0x02 | |
| #define IEEE80211_HE_PHY_CAP6_TRIG_SU_BEAMFORMER_FB 0x04 | |
| #define IEEE80211_HE_PHY_CAP6_TRIG_MU_BEAMFORMER_FB 0x08 | |
| #define IEEE80211_HE_PHY_CAP6_TRIG_CQI_FB 0x10 | |
| #define IEEE80211_HE_PHY_CAP6_PARTIAL_BW_EXT_RANGE 0x20 | |
| #define IEEE80211_HE_PHY_CAP6_PARTIAL_BANDWIDTH_DL_MUMIMO 0x40 | |
| #define IEEE80211_HE_PHY_CAP6_PPE_THRESHOLD_PRESENT 0x80 | |
| #define IEEE80211_HE_PHY_CAP7_SRP_BASED_SR 0x01 | |
| #define IEEE80211_HE_PHY_CAP7_POWER_BOOST_FACTOR_AR 0x02 | |
| #define IEEE80211_HE_PHY_CAP7_HE_SU_MU_PPDU_4XLTF_AND_08_US_GI 0x04 | |
| #define IEEE80211_HE_PHY_CAP7_MAX_NC_1 0x08 | |
| #define IEEE80211_HE_PHY_CAP7_MAX_NC_2 0x10 | |
| #define IEEE80211_HE_PHY_CAP7_MAX_NC_3 0x18 | |
| #define IEEE80211_HE_PHY_CAP7_MAX_NC_4 0x20 | |
| #define IEEE80211_HE_PHY_CAP7_MAX_NC_5 0x28 | |
| #define IEEE80211_HE_PHY_CAP7_MAX_NC_6 0x30 | |
| #define IEEE80211_HE_PHY_CAP7_MAX_NC_7 0x38 | |
| #define IEEE80211_HE_PHY_CAP7_MAX_NC_MASK 0x38 | |
| #define IEEE80211_HE_PHY_CAP7_STBC_TX_ABOVE_80MHZ 0x40 | |
| #define IEEE80211_HE_PHY_CAP7_STBC_RX_ABOVE_80MHZ 0x80 | |
| #define IEEE80211_HE_PHY_CAP8_HE_ER_SU_PPDU_4XLTF_AND_08_US_GI 0x01 | |
| #define IEEE80211_HE_PHY_CAP8_20MHZ_IN_40MHZ_HE_PPDU_IN_2G 0x02 | |
| #define IEEE80211_HE_PHY_CAP8_20MHZ_IN_160MHZ_HE_PPDU 0x04 | |
| #define IEEE80211_HE_PHY_CAP8_80MHZ_IN_160MHZ_HE_PPDU 0x08 | |
| #define IEEE80211_HE_PHY_CAP8_HE_ER_SU_1XLTF_AND_08_US_GI 0x10 | |
| #define IEEE80211_HE_PHY_CAP8_MIDAMBLE_RX_TX_2X_AND_1XLTF 0x20 | |
| #define IEEE80211_HE_PHY_CAP8_DCM_MAX_RU_242 0x00 | |
| #define IEEE80211_HE_PHY_CAP8_DCM_MAX_RU_484 0x40 | |
| #define IEEE80211_HE_PHY_CAP8_DCM_MAX_RU_996 0x80 | |
| #define IEEE80211_HE_PHY_CAP8_DCM_MAX_RU_2x996 0xc0 | |
| #define IEEE80211_HE_PHY_CAP8_DCM_MAX_RU_MASK 0xc0 | |
| #define IEEE80211_HE_PHY_CAP9_LONGER_THAN_16_SIGB_OFDM_SYM 0x01 | |
| #define IEEE80211_HE_PHY_CAP9_NON_TRIGGERED_CQI_FEEDBACK 0x02 | |
| #define IEEE80211_HE_PHY_CAP9_TX_1024_QAM_LESS_THAN_242_TONE_RU 0x04 | |
| #define IEEE80211_HE_PHY_CAP9_RX_1024_QAM_LESS_THAN_242_TONE_RU 0x08 | |
| #define IEEE80211_HE_PHY_CAP9_RX_FULL_BW_SU_USING_MU_WITH_COMP_SIGB 0x10 | |
| #define IEEE80211_HE_PHY_CAP9_RX_FULL_BW_SU_USING_MU_WITH_NON_COMP_SIGB 0x20 | |
| #define IEEE80211_HE_PHY_CAP9_NOMIMAL_PKT_PADDING_0US 0x00 | |
| #define IEEE80211_HE_PHY_CAP9_NOMIMAL_PKT_PADDING_8US 0x40 | |
| #define IEEE80211_HE_PHY_CAP9_NOMIMAL_PKT_PADDING_16US 0x80 | |
| #define IEEE80211_HE_PHY_CAP9_NOMIMAL_PKT_PADDING_RESERVED 0xc0 | |
| #define IEEE80211_HE_PHY_CAP9_NOMIMAL_PKT_PADDING_MASK 0xc0 | |
| /* 802.11ax HE TX/RX MCS NSS Support */ | |
| #define IEEE80211_TX_RX_MCS_NSS_SUPP_HIGHEST_MCS_POS (3) | |
| #define IEEE80211_TX_RX_MCS_NSS_SUPP_TX_BITMAP_POS (6) | |
| #define IEEE80211_TX_RX_MCS_NSS_SUPP_RX_BITMAP_POS (11) | |
| #define IEEE80211_TX_RX_MCS_NSS_SUPP_TX_BITMAP_MASK 0x07c0 | |
| #define IEEE80211_TX_RX_MCS_NSS_SUPP_RX_BITMAP_MASK 0xf800 | |
| /* TX/RX HE MCS Support field Highest MCS subfield encoding */ | |
| enum ieee80211_he_highest_mcs_supported_subfield_enc { | |
| HIGHEST_MCS_SUPPORTED_MCS7 = 0, | |
| HIGHEST_MCS_SUPPORTED_MCS8, | |
| HIGHEST_MCS_SUPPORTED_MCS9, | |
| HIGHEST_MCS_SUPPORTED_MCS10, | |
| HIGHEST_MCS_SUPPORTED_MCS11, | |
| }; | |
| /* Calculate 802.11ax HE capabilities IE Tx/Rx HE MCS NSS Support Field size */ | |
| static inline u8 | |
| ieee80211_he_mcs_nss_size(const struct ieee80211_he_cap_elem *he_cap) | |
| { | |
| u8 count = 4; | |
| if (he_cap->phy_cap_info[0] & | |
| IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_160MHZ_IN_5G) | |
| count += 4; | |
| if (he_cap->phy_cap_info[0] & | |
| IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_80PLUS80_MHZ_IN_5G) | |
| count += 4; | |
| return count; | |
| } | |
| /* 802.11ax HE PPE Thresholds */ | |
| #define IEEE80211_PPE_THRES_NSS_SUPPORT_2NSS (1) | |
| #define IEEE80211_PPE_THRES_NSS_POS (0) | |
| #define IEEE80211_PPE_THRES_NSS_MASK (7) | |
| #define IEEE80211_PPE_THRES_RU_INDEX_BITMASK_2x966_AND_966_RU \ | |
| (BIT(5) | BIT(6)) | |
| #define IEEE80211_PPE_THRES_RU_INDEX_BITMASK_MASK 0x78 | |
| #define IEEE80211_PPE_THRES_RU_INDEX_BITMASK_POS (3) | |
| #define IEEE80211_PPE_THRES_INFO_PPET_SIZE (3) | |
| /* | |
| * Calculate 802.11ax HE capabilities IE PPE field size | |
| * Input: Header byte of ppe_thres (first byte), and HE capa IE's PHY cap u8* | |
| */ | |
| static inline u8 | |
| ieee80211_he_ppe_size(u8 ppe_thres_hdr, const u8 *phy_cap_info) | |
| { | |
| u8 n; | |
| if ((phy_cap_info[6] & | |
| IEEE80211_HE_PHY_CAP6_PPE_THRESHOLD_PRESENT) == 0) | |
| return 0; | |
| n = hweight8(ppe_thres_hdr & | |
| IEEE80211_PPE_THRES_RU_INDEX_BITMASK_MASK); | |
| n *= (1 + ((ppe_thres_hdr & IEEE80211_PPE_THRES_NSS_MASK) >> | |
| IEEE80211_PPE_THRES_NSS_POS)); | |
| /* | |
| * Each pair is 6 bits, and we need to add the 7 "header" bits to the | |
| * total size. | |
| */ | |
| n = (n * IEEE80211_PPE_THRES_INFO_PPET_SIZE * 2) + 7; | |
| n = DIV_ROUND_UP(n, 8); | |
| return n; | |
| } | |
| /* HE Operation defines */ | |
| #define IEEE80211_HE_OPERATION_DFLT_PE_DURATION_MASK 0x00000007 | |
| #define IEEE80211_HE_OPERATION_TWT_REQUIRED 0x00000008 | |
| #define IEEE80211_HE_OPERATION_RTS_THRESHOLD_MASK 0x00003ff0 | |
| #define IEEE80211_HE_OPERATION_RTS_THRESHOLD_OFFSET 4 | |
| #define IEEE80211_HE_OPERATION_VHT_OPER_INFO 0x00004000 | |
| #define IEEE80211_HE_OPERATION_CO_HOSTED_BSS 0x00008000 | |
| #define IEEE80211_HE_OPERATION_ER_SU_DISABLE 0x00010000 | |
| #define IEEE80211_HE_OPERATION_6GHZ_OP_INFO 0x00020000 | |
| #define IEEE80211_HE_OPERATION_BSS_COLOR_MASK 0x3f000000 | |
| #define IEEE80211_HE_OPERATION_BSS_COLOR_OFFSET 24 | |
| #define IEEE80211_HE_OPERATION_PARTIAL_BSS_COLOR 0x40000000 | |
| #define IEEE80211_HE_OPERATION_BSS_COLOR_DISABLED 0x80000000 | |
| /** | |
| * ieee80211_he_6ghz_oper - HE 6 GHz operation Information field | |
| * @primary: primary channel | |
| * @control: control flags | |
| * @ccfs0: channel center frequency segment 0 | |
| * @ccfs1: channel center frequency segment 1 | |
| * @minrate: minimum rate (in 1 Mbps units) | |
| */ | |
| struct ieee80211_he_6ghz_oper { | |
| u8 primary; | |
| #define IEEE80211_HE_6GHZ_OPER_CTRL_CHANWIDTH 0x3 | |
| #define IEEE80211_HE_6GHZ_OPER_CTRL_CHANWIDTH_20MHZ 0 | |
| #define IEEE80211_HE_6GHZ_OPER_CTRL_CHANWIDTH_40MHZ 1 | |
| #define IEEE80211_HE_6GHZ_OPER_CTRL_CHANWIDTH_80MHZ 2 | |
| #define IEEE80211_HE_6GHZ_OPER_CTRL_CHANWIDTH_160MHZ 3 | |
| #define IEEE80211_HE_6GHZ_OPER_CTRL_DUP_BEACON 0x4 | |
| u8 control; | |
| u8 ccfs0; | |
| u8 ccfs1; | |
| u8 minrate; | |
| } __packed; | |
| /* | |
| * ieee80211_he_oper_size - calculate 802.11ax HE Operations IE size | |
| * @he_oper_ie: byte data of the He Operations IE, stating from the byte | |
| * after the ext ID byte. It is assumed that he_oper_ie has at least | |
| * sizeof(struct ieee80211_he_operation) bytes, the caller must have | |
| * validated this. | |
| * @return the actual size of the IE data (not including header), or 0 on error | |
| */ | |
| static inline u8 | |
| ieee80211_he_oper_size(const u8 *he_oper_ie) | |
| { | |
| struct ieee80211_he_operation *he_oper = (void *)he_oper_ie; | |
| u8 oper_len = sizeof(struct ieee80211_he_operation); | |
| u32 he_oper_params; | |
| /* Make sure the input is not NULL */ | |
| if (!he_oper_ie) | |
| return 0; | |
| /* Calc required length */ | |
| he_oper_params = le32_to_cpu(he_oper->he_oper_params); | |
| if (he_oper_params & IEEE80211_HE_OPERATION_VHT_OPER_INFO) | |
| oper_len += 3; | |
| if (he_oper_params & IEEE80211_HE_OPERATION_CO_HOSTED_BSS) | |
| oper_len++; | |
| if (he_oper_params & IEEE80211_HE_OPERATION_6GHZ_OP_INFO) | |
| oper_len += sizeof(struct ieee80211_he_6ghz_oper); | |
| /* Add the first byte (extension ID) to the total length */ | |
| oper_len++; | |
| return oper_len; | |
| } | |
| /** | |
| * ieee80211_he_6ghz_oper - obtain 6 GHz operation field | |
| * @he_oper: HE operation element (must be pre-validated for size) | |
| * but may be %NULL | |
| * | |
| * Return: a pointer to the 6 GHz operation field, or %NULL | |
| */ | |
| static inline const struct ieee80211_he_6ghz_oper * | |
| ieee80211_he_6ghz_oper(const struct ieee80211_he_operation *he_oper) | |
| { | |
| const u8 *ret = (void *)&he_oper->optional; | |
| u32 he_oper_params; | |
| if (!he_oper) | |
| return NULL; | |
| he_oper_params = le32_to_cpu(he_oper->he_oper_params); | |
| if (!(he_oper_params & IEEE80211_HE_OPERATION_6GHZ_OP_INFO)) | |
| return NULL; | |
| if (he_oper_params & IEEE80211_HE_OPERATION_VHT_OPER_INFO) | |
| ret += 3; | |
| if (he_oper_params & IEEE80211_HE_OPERATION_CO_HOSTED_BSS) | |
| ret++; | |
| return (void *)ret; | |
| } | |
| /* HE Spatial Reuse defines */ | |
| #define IEEE80211_HE_SPR_PSR_DISALLOWED BIT(0) | |
| #define IEEE80211_HE_SPR_NON_SRG_OBSS_PD_SR_DISALLOWED BIT(1) | |
| #define IEEE80211_HE_SPR_NON_SRG_OFFSET_PRESENT BIT(2) | |
| #define IEEE80211_HE_SPR_SRG_INFORMATION_PRESENT BIT(3) | |
| #define IEEE80211_HE_SPR_HESIGA_SR_VAL15_ALLOWED BIT(4) | |
| /* | |
| * ieee80211_he_spr_size - calculate 802.11ax HE Spatial Reuse IE size | |
| * @he_spr_ie: byte data of the He Spatial Reuse IE, stating from the byte | |
| * after the ext ID byte. It is assumed that he_spr_ie has at least | |
| * sizeof(struct ieee80211_he_spr) bytes, the caller must have validated | |
| * this | |
| * @return the actual size of the IE data (not including header), or 0 on error | |
| */ | |
| static inline u8 | |
| ieee80211_he_spr_size(const u8 *he_spr_ie) | |
| { | |
| struct ieee80211_he_spr *he_spr = (void *)he_spr_ie; | |
| u8 spr_len = sizeof(struct ieee80211_he_spr); | |
| u8 he_spr_params; | |
| /* Make sure the input is not NULL */ | |
| if (!he_spr_ie) | |
| return 0; | |
| /* Calc required length */ | |
| he_spr_params = he_spr->he_sr_control; | |
| if (he_spr_params & IEEE80211_HE_SPR_NON_SRG_OFFSET_PRESENT) | |
| spr_len++; | |
| if (he_spr_params & IEEE80211_HE_SPR_SRG_INFORMATION_PRESENT) | |
| spr_len += 18; | |
| /* Add the first byte (extension ID) to the total length */ | |
| spr_len++; | |
| return spr_len; | |
| } | |
| /* S1G Capabilities Information field */ | |
| #define IEEE80211_S1G_CAPABILITY_LEN 15 | |
| #define S1G_CAP0_S1G_LONG BIT(0) | |
| #define S1G_CAP0_SGI_1MHZ BIT(1) | |
| #define S1G_CAP0_SGI_2MHZ BIT(2) | |
| #define S1G_CAP0_SGI_4MHZ BIT(3) | |
| #define S1G_CAP0_SGI_8MHZ BIT(4) | |
| #define S1G_CAP0_SGI_16MHZ BIT(5) | |
| #define S1G_CAP0_SUPP_CH_WIDTH GENMASK(7, 6) | |
| #define S1G_SUPP_CH_WIDTH_2 0 | |
| #define S1G_SUPP_CH_WIDTH_4 1 | |
| #define S1G_SUPP_CH_WIDTH_8 2 | |
| #define S1G_SUPP_CH_WIDTH_16 3 | |
| #define S1G_SUPP_CH_WIDTH_MAX(cap) ((1 << FIELD_GET(S1G_CAP0_SUPP_CH_WIDTH, \ | |
| cap[0])) << 1) | |
| #define S1G_CAP1_RX_LDPC BIT(0) | |
| #define S1G_CAP1_TX_STBC BIT(1) | |
| #define S1G_CAP1_RX_STBC BIT(2) | |
| #define S1G_CAP1_SU_BFER BIT(3) | |
| #define S1G_CAP1_SU_BFEE BIT(4) | |
| #define S1G_CAP1_BFEE_STS GENMASK(7, 5) | |
| #define S1G_CAP2_SOUNDING_DIMENSIONS GENMASK(2, 0) | |
| #define S1G_CAP2_MU_BFER BIT(3) | |
| #define S1G_CAP2_MU_BFEE BIT(4) | |
| #define S1G_CAP2_PLUS_HTC_VHT BIT(5) | |
| #define S1G_CAP2_TRAVELING_PILOT GENMASK(7, 6) | |
| #define S1G_CAP3_RD_RESPONDER BIT(0) | |
| #define S1G_CAP3_HT_DELAYED_BA BIT(1) | |
| #define S1G_CAP3_MAX_MPDU_LEN BIT(2) | |
| #define S1G_CAP3_MAX_AMPDU_LEN_EXP GENMASK(4, 3) | |
| #define S1G_CAP3_MIN_MPDU_START GENMASK(7, 5) | |
| #define S1G_CAP4_UPLINK_SYNC BIT(0) | |
| #define S1G_CAP4_DYNAMIC_AID BIT(1) | |
| #define S1G_CAP4_BAT BIT(2) | |
| #define S1G_CAP4_TIME_ADE BIT(3) | |
| #define S1G_CAP4_NON_TIM BIT(4) | |
| #define S1G_CAP4_GROUP_AID BIT(5) | |
| #define S1G_CAP4_STA_TYPE GENMASK(7, 6) | |
| #define S1G_CAP5_CENT_AUTH_CONTROL BIT(0) | |
| #define S1G_CAP5_DIST_AUTH_CONTROL BIT(1) | |
| #define S1G_CAP5_AMSDU BIT(2) | |
| #define S1G_CAP5_AMPDU BIT(3) | |
| #define S1G_CAP5_ASYMMETRIC_BA BIT(4) | |
| #define S1G_CAP5_FLOW_CONTROL BIT(5) | |
| #define S1G_CAP5_SECTORIZED_BEAM GENMASK(7, 6) | |
| #define S1G_CAP6_OBSS_MITIGATION BIT(0) | |
| #define S1G_CAP6_FRAGMENT_BA BIT(1) | |
| #define S1G_CAP6_NDP_PS_POLL BIT(2) | |
| #define S1G_CAP6_RAW_OPERATION BIT(3) | |
| #define S1G_CAP6_PAGE_SLICING BIT(4) | |
| #define S1G_CAP6_TXOP_SHARING_IMP_ACK BIT(5) | |
| #define S1G_CAP6_VHT_LINK_ADAPT GENMASK(7, 6) | |
| #define S1G_CAP7_TACK_AS_PS_POLL BIT(0) | |
| #define S1G_CAP7_DUP_1MHZ BIT(1) | |
| #define S1G_CAP7_MCS_NEGOTIATION BIT(2) | |
| #define S1G_CAP7_1MHZ_CTL_RESPONSE_PREAMBLE BIT(3) | |
| #define S1G_CAP7_NDP_BFING_REPORT_POLL BIT(4) | |
| #define S1G_CAP7_UNSOLICITED_DYN_AID BIT(5) | |
| #define S1G_CAP7_SECTOR_TRAINING_OPERATION BIT(6) | |
| #define S1G_CAP7_TEMP_PS_MODE_SWITCH BIT(7) | |
| #define S1G_CAP8_TWT_GROUPING BIT(0) | |
| #define S1G_CAP8_BDT BIT(1) | |
| #define S1G_CAP8_COLOR GENMASK(4, 2) | |
| #define S1G_CAP8_TWT_REQUEST BIT(5) | |
| #define S1G_CAP8_TWT_RESPOND BIT(6) | |
| #define S1G_CAP8_PV1_FRAME BIT(7) | |
| #define S1G_CAP9_LINK_ADAPT_PER_CONTROL_RESPONSE BIT(0) | |
| #define S1G_OPER_CH_WIDTH_PRIMARY_1MHZ BIT(0) | |
| #define S1G_OPER_CH_WIDTH_OPER GENMASK(4, 1) | |
| #define LISTEN_INT_USF GENMASK(15, 14) | |
| #define LISTEN_INT_UI GENMASK(13, 0) | |
| #define IEEE80211_MAX_USF FIELD_MAX(LISTEN_INT_USF) | |
| #define IEEE80211_MAX_UI FIELD_MAX(LISTEN_INT_UI) | |
| /* Authentication algorithms */ | |
| #define WLAN_AUTH_OPEN 0 | |
| #define WLAN_AUTH_SHARED_KEY 1 | |
| #define WLAN_AUTH_FT 2 | |
| #define WLAN_AUTH_SAE 3 | |
| #define WLAN_AUTH_FILS_SK 4 | |
| #define WLAN_AUTH_FILS_SK_PFS 5 | |
| #define WLAN_AUTH_FILS_PK 6 | |
| #define WLAN_AUTH_LEAP 128 | |
| #define WLAN_AUTH_CHALLENGE_LEN 128 | |
| #define WLAN_CAPABILITY_ESS (1<<0) | |
| #define WLAN_CAPABILITY_IBSS (1<<1) | |
| /* | |
| * A mesh STA sets the ESS and IBSS capability bits to zero. | |
| * however, this holds true for p2p probe responses (in the p2p_find | |
| * phase) as well. | |
| */ | |
| #define WLAN_CAPABILITY_IS_STA_BSS(cap) \ | |
| (!((cap) & (WLAN_CAPABILITY_ESS | WLAN_CAPABILITY_IBSS))) | |
| #define WLAN_CAPABILITY_CF_POLLABLE (1<<2) | |
| #define WLAN_CAPABILITY_CF_POLL_REQUEST (1<<3) | |
| #define WLAN_CAPABILITY_PRIVACY (1<<4) | |
| #define WLAN_CAPABILITY_SHORT_PREAMBLE (1<<5) | |
| #define WLAN_CAPABILITY_PBCC (1<<6) | |
| #define WLAN_CAPABILITY_CHANNEL_AGILITY (1<<7) | |
| /* 802.11h */ | |
| #define WLAN_CAPABILITY_SPECTRUM_MGMT (1<<8) | |
| #define WLAN_CAPABILITY_QOS (1<<9) | |
| #define WLAN_CAPABILITY_SHORT_SLOT_TIME (1<<10) | |
| #define WLAN_CAPABILITY_APSD (1<<11) | |
| #define WLAN_CAPABILITY_RADIO_MEASURE (1<<12) | |
| #define WLAN_CAPABILITY_DSSS_OFDM (1<<13) | |
| #define WLAN_CAPABILITY_DEL_BACK (1<<14) | |
| #define WLAN_CAPABILITY_IMM_BACK (1<<15) | |
| /* DMG (60gHz) 802.11ad */ | |
| /* type - bits 0..1 */ | |
| #define WLAN_CAPABILITY_DMG_TYPE_MASK (3<<0) | |
| #define WLAN_CAPABILITY_DMG_TYPE_IBSS (1<<0) /* Tx by: STA */ | |
| #define WLAN_CAPABILITY_DMG_TYPE_PBSS (2<<0) /* Tx by: PCP */ | |
| #define WLAN_CAPABILITY_DMG_TYPE_AP (3<<0) /* Tx by: AP */ | |
| #define WLAN_CAPABILITY_DMG_CBAP_ONLY (1<<2) | |
| #define WLAN_CAPABILITY_DMG_CBAP_SOURCE (1<<3) | |
| #define WLAN_CAPABILITY_DMG_PRIVACY (1<<4) | |
| #define WLAN_CAPABILITY_DMG_ECPAC (1<<5) | |
| #define WLAN_CAPABILITY_DMG_SPECTRUM_MGMT (1<<8) | |
| #define WLAN_CAPABILITY_DMG_RADIO_MEASURE (1<<12) | |
| /* measurement */ | |
| #define IEEE80211_SPCT_MSR_RPRT_MODE_LATE (1<<0) | |
| #define IEEE80211_SPCT_MSR_RPRT_MODE_INCAPABLE (1<<1) | |
| #define IEEE80211_SPCT_MSR_RPRT_MODE_REFUSED (1<<2) | |
| #define IEEE80211_SPCT_MSR_RPRT_TYPE_BASIC 0 | |
| #define IEEE80211_SPCT_MSR_RPRT_TYPE_CCA 1 | |
| #define IEEE80211_SPCT_MSR_RPRT_TYPE_RPI 2 | |
| #define IEEE80211_SPCT_MSR_RPRT_TYPE_LCI 8 | |
| #define IEEE80211_SPCT_MSR_RPRT_TYPE_CIVIC 11 | |
| /* 802.11g ERP information element */ | |
| #define WLAN_ERP_NON_ERP_PRESENT (1<<0) | |
| #define WLAN_ERP_USE_PROTECTION (1<<1) | |
| #define WLAN_ERP_BARKER_PREAMBLE (1<<2) | |
| /* WLAN_ERP_BARKER_PREAMBLE values */ | |
| enum { | |
| WLAN_ERP_PREAMBLE_SHORT = 0, | |
| WLAN_ERP_PREAMBLE_LONG = 1, | |
| }; | |
| /* Band ID, 802.11ad #8.4.1.45 */ | |
| enum { | |
| IEEE80211_BANDID_TV_WS = 0, /* TV white spaces */ | |
| IEEE80211_BANDID_SUB1 = 1, /* Sub-1 GHz (excluding TV white spaces) */ | |
| IEEE80211_BANDID_2G = 2, /* 2.4 GHz */ | |
| IEEE80211_BANDID_3G = 3, /* 3.6 GHz */ | |
| IEEE80211_BANDID_5G = 4, /* 4.9 and 5 GHz */ | |
| IEEE80211_BANDID_60G = 5, /* 60 GHz */ | |
| }; | |
| /* Status codes */ | |
| enum ieee80211_statuscode { | |
| WLAN_STATUS_SUCCESS = 0, | |
| WLAN_STATUS_UNSPECIFIED_FAILURE = 1, | |
| WLAN_STATUS_CAPS_UNSUPPORTED = 10, | |
| WLAN_STATUS_REASSOC_NO_ASSOC = 11, | |
| WLAN_STATUS_ASSOC_DENIED_UNSPEC = 12, | |
| WLAN_STATUS_NOT_SUPPORTED_AUTH_ALG = 13, | |
| WLAN_STATUS_UNKNOWN_AUTH_TRANSACTION = 14, | |
| WLAN_STATUS_CHALLENGE_FAIL = 15, | |
| WLAN_STATUS_AUTH_TIMEOUT = 16, | |
| WLAN_STATUS_AP_UNABLE_TO_HANDLE_NEW_STA = 17, | |
| WLAN_STATUS_ASSOC_DENIED_RATES = 18, | |
| /* 802.11b */ | |
| WLAN_STATUS_ASSOC_DENIED_NOSHORTPREAMBLE = 19, | |
| WLAN_STATUS_ASSOC_DENIED_NOPBCC = 20, | |
| WLAN_STATUS_ASSOC_DENIED_NOAGILITY = 21, | |
| /* 802.11h */ | |
| WLAN_STATUS_ASSOC_DENIED_NOSPECTRUM = 22, | |
| WLAN_STATUS_ASSOC_REJECTED_BAD_POWER = 23, | |
| WLAN_STATUS_ASSOC_REJECTED_BAD_SUPP_CHAN = 24, | |
| /* 802.11g */ | |
| WLAN_STATUS_ASSOC_DENIED_NOSHORTTIME = 25, | |
| WLAN_STATUS_ASSOC_DENIED_NODSSSOFDM = 26, | |
| /* 802.11w */ | |
| WLAN_STATUS_ASSOC_REJECTED_TEMPORARILY = 30, | |
| WLAN_STATUS_ROBUST_MGMT_FRAME_POLICY_VIOLATION = 31, | |
| /* 802.11i */ | |
| WLAN_STATUS_INVALID_IE = 40, | |
| WLAN_STATUS_INVALID_GROUP_CIPHER = 41, | |
| WLAN_STATUS_INVALID_PAIRWISE_CIPHER = 42, | |
| WLAN_STATUS_INVALID_AKMP = 43, | |
| WLAN_STATUS_UNSUPP_RSN_VERSION = 44, | |
| WLAN_STATUS_INVALID_RSN_IE_CAP = 45, | |
| WLAN_STATUS_CIPHER_SUITE_REJECTED = 46, | |
| /* 802.11e */ | |
| WLAN_STATUS_UNSPECIFIED_QOS = 32, | |
| WLAN_STATUS_ASSOC_DENIED_NOBANDWIDTH = 33, | |
| WLAN_STATUS_ASSOC_DENIED_LOWACK = 34, | |
| WLAN_STATUS_ASSOC_DENIED_UNSUPP_QOS = 35, | |
| WLAN_STATUS_REQUEST_DECLINED = 37, | |
| WLAN_STATUS_INVALID_QOS_PARAM = 38, | |
| WLAN_STATUS_CHANGE_TSPEC = 39, | |
| WLAN_STATUS_WAIT_TS_DELAY = 47, | |
| WLAN_STATUS_NO_DIRECT_LINK = 48, | |
| WLAN_STATUS_STA_NOT_PRESENT = 49, | |
| WLAN_STATUS_STA_NOT_QSTA = 50, | |
| /* 802.11s */ | |
| WLAN_STATUS_ANTI_CLOG_REQUIRED = 76, | |
| WLAN_STATUS_FCG_NOT_SUPP = 78, | |
| WLAN_STATUS_STA_NO_TBTT = 78, | |
| /* 802.11ad */ | |
| WLAN_STATUS_REJECTED_WITH_SUGGESTED_CHANGES = 39, | |
| WLAN_STATUS_REJECTED_FOR_DELAY_PERIOD = 47, | |
| WLAN_STATUS_REJECT_WITH_SCHEDULE = 83, | |
| WLAN_STATUS_PENDING_ADMITTING_FST_SESSION = 86, | |
| WLAN_STATUS_PERFORMING_FST_NOW = 87, | |
| WLAN_STATUS_PENDING_GAP_IN_BA_WINDOW = 88, | |
| WLAN_STATUS_REJECT_U_PID_SETTING = 89, | |
| WLAN_STATUS_REJECT_DSE_BAND = 96, | |
| WLAN_STATUS_DENIED_WITH_SUGGESTED_BAND_AND_CHANNEL = 99, | |
| WLAN_STATUS_DENIED_DUE_TO_SPECTRUM_MANAGEMENT = 103, | |
| /* 802.11ai */ | |
| WLAN_STATUS_FILS_AUTHENTICATION_FAILURE = 108, | |
| WLAN_STATUS_UNKNOWN_AUTHENTICATION_SERVER = 109, | |
| WLAN_STATUS_SAE_HASH_TO_ELEMENT = 126, | |
| WLAN_STATUS_SAE_PK = 127, | |
| }; | |
| /* Reason codes */ | |
| enum ieee80211_reasoncode { | |
| WLAN_REASON_UNSPECIFIED = 1, | |
| WLAN_REASON_PREV_AUTH_NOT_VALID = 2, | |
| WLAN_REASON_DEAUTH_LEAVING = 3, | |
| WLAN_REASON_DISASSOC_DUE_TO_INACTIVITY = 4, | |
| WLAN_REASON_DISASSOC_AP_BUSY = 5, | |
| WLAN_REASON_CLASS2_FRAME_FROM_NONAUTH_STA = 6, | |
| WLAN_REASON_CLASS3_FRAME_FROM_NONASSOC_STA = 7, | |
| WLAN_REASON_DISASSOC_STA_HAS_LEFT = 8, | |
| WLAN_REASON_STA_REQ_ASSOC_WITHOUT_AUTH = 9, | |
| /* 802.11h */ | |
| WLAN_REASON_DISASSOC_BAD_POWER = 10, | |
| WLAN_REASON_DISASSOC_BAD_SUPP_CHAN = 11, | |
| /* 802.11i */ | |
| WLAN_REASON_INVALID_IE = 13, | |
| WLAN_REASON_MIC_FAILURE = 14, | |
| WLAN_REASON_4WAY_HANDSHAKE_TIMEOUT = 15, | |
| WLAN_REASON_GROUP_KEY_HANDSHAKE_TIMEOUT = 16, | |
| WLAN_REASON_IE_DIFFERENT = 17, | |
| WLAN_REASON_INVALID_GROUP_CIPHER = 18, | |
| WLAN_REASON_INVALID_PAIRWISE_CIPHER = 19, | |
| WLAN_REASON_INVALID_AKMP = 20, | |
| WLAN_REASON_UNSUPP_RSN_VERSION = 21, | |
| WLAN_REASON_INVALID_RSN_IE_CAP = 22, | |
| WLAN_REASON_IEEE8021X_FAILED = 23, | |
| WLAN_REASON_CIPHER_SUITE_REJECTED = 24, | |
| /* TDLS (802.11z) */ | |
| WLAN_REASON_TDLS_TEARDOWN_UNREACHABLE = 25, | |
| WLAN_REASON_TDLS_TEARDOWN_UNSPECIFIED = 26, | |
| /* 802.11e */ | |
| WLAN_REASON_DISASSOC_UNSPECIFIED_QOS = 32, | |
| WLAN_REASON_DISASSOC_QAP_NO_BANDWIDTH = 33, | |
| WLAN_REASON_DISASSOC_LOW_ACK = 34, | |
| WLAN_REASON_DISASSOC_QAP_EXCEED_TXOP = 35, | |
| WLAN_REASON_QSTA_LEAVE_QBSS = 36, | |
| WLAN_REASON_QSTA_NOT_USE = 37, | |
| WLAN_REASON_QSTA_REQUIRE_SETUP = 38, | |
| WLAN_REASON_QSTA_TIMEOUT = 39, | |
| WLAN_REASON_QSTA_CIPHER_NOT_SUPP = 45, | |
| /* 802.11s */ | |
| WLAN_REASON_MESH_PEER_CANCELED = 52, | |
| WLAN_REASON_MESH_MAX_PEERS = 53, | |
| WLAN_REASON_MESH_CONFIG = 54, | |
| WLAN_REASON_MESH_CLOSE = 55, | |
| WLAN_REASON_MESH_MAX_RETRIES = 56, | |
| WLAN_REASON_MESH_CONFIRM_TIMEOUT = 57, | |
| WLAN_REASON_MESH_INVALID_GTK = 58, | |
| WLAN_REASON_MESH_INCONSISTENT_PARAM = 59, | |
| WLAN_REASON_MESH_INVALID_SECURITY = 60, | |
| WLAN_REASON_MESH_PATH_ERROR = 61, | |
| WLAN_REASON_MESH_PATH_NOFORWARD = 62, | |
| WLAN_REASON_MESH_PATH_DEST_UNREACHABLE = 63, | |
| WLAN_REASON_MAC_EXISTS_IN_MBSS = 64, | |
| WLAN_REASON_MESH_CHAN_REGULATORY = 65, | |
| WLAN_REASON_MESH_CHAN = 66, | |
| }; | |
| /* Information Element IDs */ | |
| enum ieee80211_eid { | |
| WLAN_EID_SSID = 0, | |
| WLAN_EID_SUPP_RATES = 1, | |
| WLAN_EID_FH_PARAMS = 2, /* reserved now */ | |
| WLAN_EID_DS_PARAMS = 3, | |
| WLAN_EID_CF_PARAMS = 4, | |
| WLAN_EID_TIM = 5, | |
| WLAN_EID_IBSS_PARAMS = 6, | |
| WLAN_EID_COUNTRY = 7, | |
| /* 8, 9 reserved */ | |
| WLAN_EID_REQUEST = 10, | |
| WLAN_EID_QBSS_LOAD = 11, | |
| WLAN_EID_EDCA_PARAM_SET = 12, | |
| WLAN_EID_TSPEC = 13, | |
| WLAN_EID_TCLAS = 14, | |
| WLAN_EID_SCHEDULE = 15, | |
| WLAN_EID_CHALLENGE = 16, | |
| /* 17-31 reserved for challenge text extension */ | |
| WLAN_EID_PWR_CONSTRAINT = 32, | |
| WLAN_EID_PWR_CAPABILITY = 33, | |
| WLAN_EID_TPC_REQUEST = 34, | |
| WLAN_EID_TPC_REPORT = 35, | |
| WLAN_EID_SUPPORTED_CHANNELS = 36, | |
| WLAN_EID_CHANNEL_SWITCH = 37, | |
| WLAN_EID_MEASURE_REQUEST = 38, | |
| WLAN_EID_MEASURE_REPORT = 39, | |
| WLAN_EID_QUIET = 40, | |
| WLAN_EID_IBSS_DFS = 41, | |
| WLAN_EID_ERP_INFO = 42, | |
| WLAN_EID_TS_DELAY = 43, | |
| WLAN_EID_TCLAS_PROCESSING = 44, | |
| WLAN_EID_HT_CAPABILITY = 45, | |
| WLAN_EID_QOS_CAPA = 46, | |
| /* 47 reserved for Broadcom */ | |
| WLAN_EID_RSN = 48, | |
| WLAN_EID_802_15_COEX = 49, | |
| WLAN_EID_EXT_SUPP_RATES = 50, | |
| WLAN_EID_AP_CHAN_REPORT = 51, | |
| WLAN_EID_NEIGHBOR_REPORT = 52, | |
| WLAN_EID_RCPI = 53, | |
| WLAN_EID_MOBILITY_DOMAIN = 54, | |
| WLAN_EID_FAST_BSS_TRANSITION = 55, | |
| WLAN_EID_TIMEOUT_INTERVAL = 56, | |
| WLAN_EID_RIC_DATA = 57, | |
| WLAN_EID_DSE_REGISTERED_LOCATION = 58, | |
| WLAN_EID_SUPPORTED_REGULATORY_CLASSES = 59, | |
| WLAN_EID_EXT_CHANSWITCH_ANN = 60, | |
| WLAN_EID_HT_OPERATION = 61, | |
| WLAN_EID_SECONDARY_CHANNEL_OFFSET = 62, | |
| WLAN_EID_BSS_AVG_ACCESS_DELAY = 63, | |
| WLAN_EID_ANTENNA_INFO = 64, | |
| WLAN_EID_RSNI = 65, | |
| WLAN_EID_MEASUREMENT_PILOT_TX_INFO = 66, | |
| WLAN_EID_BSS_AVAILABLE_CAPACITY = 67, | |
| WLAN_EID_BSS_AC_ACCESS_DELAY = 68, | |
| WLAN_EID_TIME_ADVERTISEMENT = 69, | |
| WLAN_EID_RRM_ENABLED_CAPABILITIES = 70, | |
| WLAN_EID_MULTIPLE_BSSID = 71, | |
| WLAN_EID_BSS_COEX_2040 = 72, | |
| WLAN_EID_BSS_INTOLERANT_CHL_REPORT = 73, | |
| WLAN_EID_OVERLAP_BSS_SCAN_PARAM = 74, | |
| WLAN_EID_RIC_DESCRIPTOR = 75, | |
| WLAN_EID_MMIE = 76, | |
| WLAN_EID_ASSOC_COMEBACK_TIME = 77, | |
| WLAN_EID_EVENT_REQUEST = 78, | |
| WLAN_EID_EVENT_REPORT = 79, | |
| WLAN_EID_DIAGNOSTIC_REQUEST = 80, | |
| WLAN_EID_DIAGNOSTIC_REPORT = 81, | |
| WLAN_EID_LOCATION_PARAMS = 82, | |
| WLAN_EID_NON_TX_BSSID_CAP = 83, | |
| WLAN_EID_SSID_LIST = 84, | |
| WLAN_EID_MULTI_BSSID_IDX = 85, | |
| WLAN_EID_FMS_DESCRIPTOR = 86, | |
| WLAN_EID_FMS_REQUEST = 87, | |
| WLAN_EID_FMS_RESPONSE = 88, | |
| WLAN_EID_QOS_TRAFFIC_CAPA = 89, | |
| WLAN_EID_BSS_MAX_IDLE_PERIOD = 90, | |
| WLAN_EID_TSF_REQUEST = 91, | |
| WLAN_EID_TSF_RESPOSNE = 92, | |
| WLAN_EID_WNM_SLEEP_MODE = 93, | |
| WLAN_EID_TIM_BCAST_REQ = 94, | |
| WLAN_EID_TIM_BCAST_RESP = 95, | |
| WLAN_EID_COLL_IF_REPORT = 96, | |
| WLAN_EID_CHANNEL_USAGE = 97, | |
| WLAN_EID_TIME_ZONE = 98, | |
| WLAN_EID_DMS_REQUEST = 99, | |
| WLAN_EID_DMS_RESPONSE = 100, | |
| WLAN_EID_LINK_ID = 101, | |
| WLAN_EID_WAKEUP_SCHEDUL = 102, | |
| /* 103 reserved */ | |
| WLAN_EID_CHAN_SWITCH_TIMING = 104, | |
| WLAN_EID_PTI_CONTROL = 105, | |
| WLAN_EID_PU_BUFFER_STATUS = 106, | |
| WLAN_EID_INTERWORKING = 107, | |
| WLAN_EID_ADVERTISEMENT_PROTOCOL = 108, | |
| WLAN_EID_EXPEDITED_BW_REQ = 109, | |
| WLAN_EID_QOS_MAP_SET = 110, | |
| WLAN_EID_ROAMING_CONSORTIUM = 111, | |
| WLAN_EID_EMERGENCY_ALERT = 112, | |
| WLAN_EID_MESH_CONFIG = 113, | |
| WLAN_EID_MESH_ID = 114, | |
| WLAN_EID_LINK_METRIC_REPORT = 115, | |
| WLAN_EID_CONGESTION_NOTIFICATION = 116, | |
| WLAN_EID_PEER_MGMT = 117, | |
| WLAN_EID_CHAN_SWITCH_PARAM = 118, | |
| WLAN_EID_MESH_AWAKE_WINDOW = 119, | |
| WLAN_EID_BEACON_TIMING = 120, | |
| WLAN_EID_MCCAOP_SETUP_REQ = 121, | |
| WLAN_EID_MCCAOP_SETUP_RESP = 122, | |
| WLAN_EID_MCCAOP_ADVERT = 123, | |
| WLAN_EID_MCCAOP_TEARDOWN = 124, | |
| WLAN_EID_GANN = 125, | |
| WLAN_EID_RANN = 126, | |
| WLAN_EID_EXT_CAPABILITY = 127, | |
| /* 128, 129 reserved for Agere */ | |
| WLAN_EID_PREQ = 130, | |
| WLAN_EID_PREP = 131, | |
| WLAN_EID_PERR = 132, | |
| /* 133-136 reserved for Cisco */ | |
| WLAN_EID_PXU = 137, | |
| WLAN_EID_PXUC = 138, | |
| WLAN_EID_AUTH_MESH_PEER_EXCH = 139, | |
| WLAN_EID_MIC = 140, | |
| WLAN_EID_DESTINATION_URI = 141, | |
| WLAN_EID_UAPSD_COEX = 142, | |
| WLAN_EID_WAKEUP_SCHEDULE = 143, | |
| WLAN_EID_EXT_SCHEDULE = 144, | |
| WLAN_EID_STA_AVAILABILITY = 145, | |
| WLAN_EID_DMG_TSPEC = 146, | |
| WLAN_EID_DMG_AT = 147, | |
| WLAN_EID_DMG_CAP = 148, | |
| /* 149 reserved for Cisco */ | |
| WLAN_EID_CISCO_VENDOR_SPECIFIC = 150, | |
| WLAN_EID_DMG_OPERATION = 151, | |
| WLAN_EID_DMG_BSS_PARAM_CHANGE = 152, | |
| WLAN_EID_DMG_BEAM_REFINEMENT = 153, | |
| WLAN_EID_CHANNEL_MEASURE_FEEDBACK = 154, | |
| /* 155-156 reserved for Cisco */ | |
| WLAN_EID_AWAKE_WINDOW = 157, | |
| WLAN_EID_MULTI_BAND = 158, | |
| WLAN_EID_ADDBA_EXT = 159, | |
| WLAN_EID_NEXT_PCP_LIST = 160, | |
| WLAN_EID_PCP_HANDOVER = 161, | |
| WLAN_EID_DMG_LINK_MARGIN = 162, | |
| WLAN_EID_SWITCHING_STREAM = 163, | |
| WLAN_EID_SESSION_TRANSITION = 164, | |
| WLAN_EID_DYN_TONE_PAIRING_REPORT = 165, | |
| WLAN_EID_CLUSTER_REPORT = 166, | |
| WLAN_EID_RELAY_CAP = 167, | |
| WLAN_EID_RELAY_XFER_PARAM_SET = 168, | |
| WLAN_EID_BEAM_LINK_MAINT = 169, | |
| WLAN_EID_MULTIPLE_MAC_ADDR = 170, | |
| WLAN_EID_U_PID = 171, | |
| WLAN_EID_DMG_LINK_ADAPT_ACK = 172, | |
| /* 173 reserved for Symbol */ | |
| WLAN_EID_MCCAOP_ADV_OVERVIEW = 174, | |
| WLAN_EID_QUIET_PERIOD_REQ = 175, | |
| /* 176 reserved for Symbol */ | |
| WLAN_EID_QUIET_PERIOD_RESP = 177, | |
| /* 178-179 reserved for Symbol */ | |
| /* 180 reserved for ISO/IEC 20011 */ | |
| WLAN_EID_EPAC_POLICY = 182, | |
| WLAN_EID_CLISTER_TIME_OFF = 183, | |
| WLAN_EID_INTER_AC_PRIO = 184, | |
| WLAN_EID_SCS_DESCRIPTOR = 185, | |
| WLAN_EID_QLOAD_REPORT = 186, | |
| WLAN_EID_HCCA_TXOP_UPDATE_COUNT = 187, | |
| WLAN_EID_HL_STREAM_ID = 188, | |
| WLAN_EID_GCR_GROUP_ADDR = 189, | |
| WLAN_EID_ANTENNA_SECTOR_ID_PATTERN = 190, | |
| WLAN_EID_VHT_CAPABILITY = 191, | |
| WLAN_EID_VHT_OPERATION = 192, | |
| WLAN_EID_EXTENDED_BSS_LOAD = 193, | |
| WLAN_EID_WIDE_BW_CHANNEL_SWITCH = 194, | |
| WLAN_EID_VHT_TX_POWER_ENVELOPE = 195, | |
| WLAN_EID_CHANNEL_SWITCH_WRAPPER = 196, | |
| WLAN_EID_AID = 197, | |
| WLAN_EID_QUIET_CHANNEL = 198, | |
| WLAN_EID_OPMODE_NOTIF = 199, | |
| WLAN_EID_REDUCED_NEIGHBOR_REPORT = 201, | |
| WLAN_EID_AID_REQUEST = 210, | |
| WLAN_EID_AID_RESPONSE = 211, | |
| WLAN_EID_S1G_BCN_COMPAT = 213, | |
| WLAN_EID_S1G_SHORT_BCN_INTERVAL = 214, | |
| WLAN_EID_S1G_CAPABILITIES = 217, | |
| WLAN_EID_VENDOR_SPECIFIC = 221, | |
| WLAN_EID_QOS_PARAMETER = 222, | |
| WLAN_EID_S1G_OPERATION = 232, | |
| WLAN_EID_CAG_NUMBER = 237, | |
| WLAN_EID_AP_CSN = 239, | |
| WLAN_EID_FILS_INDICATION = 240, | |
| WLAN_EID_DILS = 241, | |
| WLAN_EID_FRAGMENT = 242, | |
| WLAN_EID_RSNX = 244, | |
| WLAN_EID_EXTENSION = 255 | |
| }; | |
| /* Element ID Extensions for Element ID 255 */ | |
| enum ieee80211_eid_ext { | |
| WLAN_EID_EXT_ASSOC_DELAY_INFO = 1, | |
| WLAN_EID_EXT_FILS_REQ_PARAMS = 2, | |
| WLAN_EID_EXT_FILS_KEY_CONFIRM = 3, | |
| WLAN_EID_EXT_FILS_SESSION = 4, | |
| WLAN_EID_EXT_FILS_HLP_CONTAINER = 5, | |
| WLAN_EID_EXT_FILS_IP_ADDR_ASSIGN = 6, | |
| WLAN_EID_EXT_KEY_DELIVERY = 7, | |
| WLAN_EID_EXT_FILS_WRAPPED_DATA = 8, | |
| WLAN_EID_EXT_FILS_PUBLIC_KEY = 12, | |
| WLAN_EID_EXT_FILS_NONCE = 13, | |
| WLAN_EID_EXT_FUTURE_CHAN_GUIDANCE = 14, | |
| WLAN_EID_EXT_HE_CAPABILITY = 35, | |
| WLAN_EID_EXT_HE_OPERATION = 36, | |
| WLAN_EID_EXT_UORA = 37, | |
| WLAN_EID_EXT_HE_MU_EDCA = 38, | |
| WLAN_EID_EXT_HE_SPR = 39, | |
| WLAN_EID_EXT_NDP_FEEDBACK_REPORT_PARAMSET = 41, | |
| WLAN_EID_EXT_BSS_COLOR_CHG_ANN = 42, | |
| WLAN_EID_EXT_QUIET_TIME_PERIOD_SETUP = 43, | |
| WLAN_EID_EXT_ESS_REPORT = 45, | |
| WLAN_EID_EXT_OPS = 46, | |
| WLAN_EID_EXT_HE_BSS_LOAD = 47, | |
| WLAN_EID_EXT_MAX_CHANNEL_SWITCH_TIME = 52, | |
| WLAN_EID_EXT_MULTIPLE_BSSID_CONFIGURATION = 55, | |
| WLAN_EID_EXT_NON_INHERITANCE = 56, | |
| WLAN_EID_EXT_KNOWN_BSSID = 57, | |
| WLAN_EID_EXT_SHORT_SSID_LIST = 58, | |
| WLAN_EID_EXT_HE_6GHZ_CAPA = 59, | |
| WLAN_EID_EXT_UL_MU_POWER_CAPA = 60, | |
| }; | |
| /* Action category code */ | |
| enum ieee80211_category { | |
| WLAN_CATEGORY_SPECTRUM_MGMT = 0, | |
| WLAN_CATEGORY_QOS = 1, | |
| WLAN_CATEGORY_DLS = 2, | |
| WLAN_CATEGORY_BACK = 3, | |
| WLAN_CATEGORY_PUBLIC = 4, | |
| WLAN_CATEGORY_RADIO_MEASUREMENT = 5, | |
| WLAN_CATEGORY_HT = 7, | |
| WLAN_CATEGORY_SA_QUERY = 8, | |
| WLAN_CATEGORY_PROTECTED_DUAL_OF_ACTION = 9, | |
| WLAN_CATEGORY_WNM = 10, | |
| WLAN_CATEGORY_WNM_UNPROTECTED = 11, | |
| WLAN_CATEGORY_TDLS = 12, | |
| WLAN_CATEGORY_MESH_ACTION = 13, | |
| WLAN_CATEGORY_MULTIHOP_ACTION = 14, | |
| WLAN_CATEGORY_SELF_PROTECTED = 15, | |
| WLAN_CATEGORY_DMG = 16, | |
| WLAN_CATEGORY_WMM = 17, | |
| WLAN_CATEGORY_FST = 18, | |
| WLAN_CATEGORY_UNPROT_DMG = 20, | |
| WLAN_CATEGORY_VHT = 21, | |
| WLAN_CATEGORY_VENDOR_SPECIFIC_PROTECTED = 126, | |
| WLAN_CATEGORY_VENDOR_SPECIFIC = 127, | |
| }; | |
| /* SPECTRUM_MGMT action code */ | |
| enum ieee80211_spectrum_mgmt_actioncode { | |
| WLAN_ACTION_SPCT_MSR_REQ = 0, | |
| WLAN_ACTION_SPCT_MSR_RPRT = 1, | |
| WLAN_ACTION_SPCT_TPC_REQ = 2, | |
| WLAN_ACTION_SPCT_TPC_RPRT = 3, | |
| WLAN_ACTION_SPCT_CHL_SWITCH = 4, | |
| }; | |
| /* HT action codes */ | |
| enum ieee80211_ht_actioncode { | |
| WLAN_HT_ACTION_NOTIFY_CHANWIDTH = 0, | |
| WLAN_HT_ACTION_SMPS = 1, | |
| WLAN_HT_ACTION_PSMP = 2, | |
| WLAN_HT_ACTION_PCO_PHASE = 3, | |
| WLAN_HT_ACTION_CSI = 4, | |
| WLAN_HT_ACTION_NONCOMPRESSED_BF = 5, | |
| WLAN_HT_ACTION_COMPRESSED_BF = 6, | |
| WLAN_HT_ACTION_ASEL_IDX_FEEDBACK = 7, | |
| }; | |
| /* VHT action codes */ | |
| enum ieee80211_vht_actioncode { | |
| WLAN_VHT_ACTION_COMPRESSED_BF = 0, | |
| WLAN_VHT_ACTION_GROUPID_MGMT = 1, | |
| WLAN_VHT_ACTION_OPMODE_NOTIF = 2, | |
| }; | |
| /* Self Protected Action codes */ | |
| enum ieee80211_self_protected_actioncode { | |
| WLAN_SP_RESERVED = 0, | |
| WLAN_SP_MESH_PEERING_OPEN = 1, | |
| WLAN_SP_MESH_PEERING_CONFIRM = 2, | |
| WLAN_SP_MESH_PEERING_CLOSE = 3, | |
| WLAN_SP_MGK_INFORM = 4, | |
| WLAN_SP_MGK_ACK = 5, | |
| }; | |
| /* Mesh action codes */ | |
| enum ieee80211_mesh_actioncode { | |
| WLAN_MESH_ACTION_LINK_METRIC_REPORT, | |
| WLAN_MESH_ACTION_HWMP_PATH_SELECTION, | |
| WLAN_MESH_ACTION_GATE_ANNOUNCEMENT, | |
| WLAN_MESH_ACTION_CONGESTION_CONTROL_NOTIFICATION, | |
| WLAN_MESH_ACTION_MCCA_SETUP_REQUEST, | |
| WLAN_MESH_ACTION_MCCA_SETUP_REPLY, | |
| WLAN_MESH_ACTION_MCCA_ADVERTISEMENT_REQUEST, | |
| WLAN_MESH_ACTION_MCCA_ADVERTISEMENT, | |
| WLAN_MESH_ACTION_MCCA_TEARDOWN, | |
| WLAN_MESH_ACTION_TBTT_ADJUSTMENT_REQUEST, | |
| WLAN_MESH_ACTION_TBTT_ADJUSTMENT_RESPONSE, | |
| }; | |
| /* Security key length */ | |
| enum ieee80211_key_len { | |
| WLAN_KEY_LEN_WEP40 = 5, | |
| WLAN_KEY_LEN_WEP104 = 13, | |
| WLAN_KEY_LEN_CCMP = 16, | |
| WLAN_KEY_LEN_CCMP_256 = 32, | |
| WLAN_KEY_LEN_TKIP = 32, | |
| WLAN_KEY_LEN_AES_CMAC = 16, | |
| WLAN_KEY_LEN_SMS4 = 32, | |
| WLAN_KEY_LEN_GCMP = 16, | |
| WLAN_KEY_LEN_GCMP_256 = 32, | |
| WLAN_KEY_LEN_BIP_CMAC_256 = 32, | |
| WLAN_KEY_LEN_BIP_GMAC_128 = 16, | |
| WLAN_KEY_LEN_BIP_GMAC_256 = 32, | |
| }; | |
| #define IEEE80211_WEP_IV_LEN 4 | |
| #define IEEE80211_WEP_ICV_LEN 4 | |
| #define IEEE80211_CCMP_HDR_LEN 8 | |
| #define IEEE80211_CCMP_MIC_LEN 8 | |
| #define IEEE80211_CCMP_PN_LEN 6 | |
| #define IEEE80211_CCMP_256_HDR_LEN 8 | |
| #define IEEE80211_CCMP_256_MIC_LEN 16 | |
| #define IEEE80211_CCMP_256_PN_LEN 6 | |
| #define IEEE80211_TKIP_IV_LEN 8 | |
| #define IEEE80211_TKIP_ICV_LEN 4 | |
| #define IEEE80211_CMAC_PN_LEN 6 | |
| #define IEEE80211_GMAC_PN_LEN 6 | |
| #define IEEE80211_GCMP_HDR_LEN 8 | |
| #define IEEE80211_GCMP_MIC_LEN 16 | |
| #define IEEE80211_GCMP_PN_LEN 6 | |
| #define FILS_NONCE_LEN 16 | |
| #define FILS_MAX_KEK_LEN 64 | |
| #define FILS_ERP_MAX_USERNAME_LEN 16 | |
| #define FILS_ERP_MAX_REALM_LEN 253 | |
| #define FILS_ERP_MAX_RRK_LEN 64 | |
| #define PMK_MAX_LEN 64 | |
| #define SAE_PASSWORD_MAX_LEN 128 | |
| /* Public action codes (IEEE Std 802.11-2016, 9.6.8.1, Table 9-307) */ | |
| enum ieee80211_pub_actioncode { | |
| WLAN_PUB_ACTION_20_40_BSS_COEX = 0, | |
| WLAN_PUB_ACTION_DSE_ENABLEMENT = 1, | |
| WLAN_PUB_ACTION_DSE_DEENABLEMENT = 2, | |
| WLAN_PUB_ACTION_DSE_REG_LOC_ANN = 3, | |
| WLAN_PUB_ACTION_EXT_CHANSW_ANN = 4, | |
| WLAN_PUB_ACTION_DSE_MSMT_REQ = 5, | |
| WLAN_PUB_ACTION_DSE_MSMT_RESP = 6, | |
| WLAN_PUB_ACTION_MSMT_PILOT = 7, | |
| WLAN_PUB_ACTION_DSE_PC = 8, | |
| WLAN_PUB_ACTION_VENDOR_SPECIFIC = 9, | |
| WLAN_PUB_ACTION_GAS_INITIAL_REQ = 10, | |
| WLAN_PUB_ACTION_GAS_INITIAL_RESP = 11, | |
| WLAN_PUB_ACTION_GAS_COMEBACK_REQ = 12, | |
| WLAN_PUB_ACTION_GAS_COMEBACK_RESP = 13, | |
| WLAN_PUB_ACTION_TDLS_DISCOVER_RES = 14, | |
| WLAN_PUB_ACTION_LOC_TRACK_NOTI = 15, | |
| WLAN_PUB_ACTION_QAB_REQUEST_FRAME = 16, | |
| WLAN_PUB_ACTION_QAB_RESPONSE_FRAME = 17, | |
| WLAN_PUB_ACTION_QMF_POLICY = 18, | |
| WLAN_PUB_ACTION_QMF_POLICY_CHANGE = 19, | |
| WLAN_PUB_ACTION_QLOAD_REQUEST = 20, | |
| WLAN_PUB_ACTION_QLOAD_REPORT = 21, | |
| WLAN_PUB_ACTION_HCCA_TXOP_ADVERT = 22, | |
| WLAN_PUB_ACTION_HCCA_TXOP_RESPONSE = 23, | |
| WLAN_PUB_ACTION_PUBLIC_KEY = 24, | |
| WLAN_PUB_ACTION_CHANNEL_AVAIL_QUERY = 25, | |
| WLAN_PUB_ACTION_CHANNEL_SCHEDULE_MGMT = 26, | |
| WLAN_PUB_ACTION_CONTACT_VERI_SIGNAL = 27, | |
| WLAN_PUB_ACTION_GDD_ENABLEMENT_REQ = 28, | |
| WLAN_PUB_ACTION_GDD_ENABLEMENT_RESP = 29, | |
| WLAN_PUB_ACTION_NETWORK_CHANNEL_CONTROL = 30, | |
| WLAN_PUB_ACTION_WHITE_SPACE_MAP_ANN = 31, | |
| WLAN_PUB_ACTION_FTM_REQUEST = 32, | |
| WLAN_PUB_ACTION_FTM = 33, | |
| WLAN_PUB_ACTION_FILS_DISCOVERY = 34, | |
| }; | |
| /* TDLS action codes */ | |
| enum ieee80211_tdls_actioncode { | |
| WLAN_TDLS_SETUP_REQUEST = 0, | |
| WLAN_TDLS_SETUP_RESPONSE = 1, | |
| WLAN_TDLS_SETUP_CONFIRM = 2, | |
| WLAN_TDLS_TEARDOWN = 3, | |
| WLAN_TDLS_PEER_TRAFFIC_INDICATION = 4, | |
| WLAN_TDLS_CHANNEL_SWITCH_REQUEST = 5, | |
| WLAN_TDLS_CHANNEL_SWITCH_RESPONSE = 6, | |
| WLAN_TDLS_PEER_PSM_REQUEST = 7, | |
| WLAN_TDLS_PEER_PSM_RESPONSE = 8, | |
| WLAN_TDLS_PEER_TRAFFIC_RESPONSE = 9, | |
| WLAN_TDLS_DISCOVERY_REQUEST = 10, | |
| }; | |
| /* Extended Channel Switching capability to be set in the 1st byte of | |
| * the @WLAN_EID_EXT_CAPABILITY information element | |
| */ | |
| #define WLAN_EXT_CAPA1_EXT_CHANNEL_SWITCHING BIT(2) | |
| /* Multiple BSSID capability is set in the 6th bit of 3rd byte of the | |
| * @WLAN_EID_EXT_CAPABILITY information element | |
| */ | |
| #define WLAN_EXT_CAPA3_MULTI_BSSID_SUPPORT BIT(6) | |
| /* TDLS capabilities in the 4th byte of @WLAN_EID_EXT_CAPABILITY */ | |
| #define WLAN_EXT_CAPA4_TDLS_BUFFER_STA BIT(4) | |
| #define WLAN_EXT_CAPA4_TDLS_PEER_PSM BIT(5) | |
| #define WLAN_EXT_CAPA4_TDLS_CHAN_SWITCH BIT(6) | |
| /* Interworking capabilities are set in 7th bit of 4th byte of the | |
| * @WLAN_EID_EXT_CAPABILITY information element | |
| */ | |
| #define WLAN_EXT_CAPA4_INTERWORKING_ENABLED BIT(7) | |
| /* | |
| * TDLS capabililites to be enabled in the 5th byte of the | |
| * @WLAN_EID_EXT_CAPABILITY information element | |
| */ | |
| #define WLAN_EXT_CAPA5_TDLS_ENABLED BIT(5) | |
| #define WLAN_EXT_CAPA5_TDLS_PROHIBITED BIT(6) | |
| #define WLAN_EXT_CAPA5_TDLS_CH_SW_PROHIBITED BIT(7) | |
| #define WLAN_EXT_CAPA8_TDLS_WIDE_BW_ENABLED BIT(5) | |
| #define WLAN_EXT_CAPA8_OPMODE_NOTIF BIT(6) | |
| /* Defines the maximal number of MSDUs in an A-MSDU. */ | |
| #define WLAN_EXT_CAPA8_MAX_MSDU_IN_AMSDU_LSB BIT(7) | |
| #define WLAN_EXT_CAPA9_MAX_MSDU_IN_AMSDU_MSB BIT(0) | |
| /* | |
| * Fine Timing Measurement Initiator - bit 71 of @WLAN_EID_EXT_CAPABILITY | |
| * information element | |
| */ | |
| #define WLAN_EXT_CAPA9_FTM_INITIATOR BIT(7) | |
| /* Defines support for TWT Requester and TWT Responder */ | |
| #define WLAN_EXT_CAPA10_TWT_REQUESTER_SUPPORT BIT(5) | |
| #define WLAN_EXT_CAPA10_TWT_RESPONDER_SUPPORT BIT(6) | |
| /* | |
| * When set, indicates that the AP is able to tolerate 26-tone RU UL | |
| * OFDMA transmissions using HE TB PPDU from OBSS (not falsely classify the | |
| * 26-tone RU UL OFDMA transmissions as radar pulses). | |
| */ | |
| #define WLAN_EXT_CAPA10_OBSS_NARROW_BW_RU_TOLERANCE_SUPPORT BIT(7) | |
| /* Defines support for enhanced multi-bssid advertisement*/ | |
| #define WLAN_EXT_CAPA11_EMA_SUPPORT BIT(3) | |
| /* TDLS specific payload type in the LLC/SNAP header */ | |
| #define WLAN_TDLS_SNAP_RFTYPE 0x2 | |
| /* BSS Coex IE information field bits */ | |
| #define WLAN_BSS_COEX_INFORMATION_REQUEST BIT(0) | |
| /** | |
| * enum ieee80211_mesh_sync_method - mesh synchronization method identifier | |
| * | |
| * @IEEE80211_SYNC_METHOD_NEIGHBOR_OFFSET: the default synchronization method | |
| * @IEEE80211_SYNC_METHOD_VENDOR: a vendor specific synchronization method | |
| * that will be specified in a vendor specific information element | |
| */ | |
| enum ieee80211_mesh_sync_method { | |
| IEEE80211_SYNC_METHOD_NEIGHBOR_OFFSET = 1, | |
| IEEE80211_SYNC_METHOD_VENDOR = 255, | |
| }; | |
| /** | |
| * enum ieee80211_mesh_path_protocol - mesh path selection protocol identifier | |
| * | |
| * @IEEE80211_PATH_PROTOCOL_HWMP: the default path selection protocol | |
| * @IEEE80211_PATH_PROTOCOL_VENDOR: a vendor specific protocol that will | |
| * be specified in a vendor specific information element | |
| */ | |
| enum ieee80211_mesh_path_protocol { | |
| IEEE80211_PATH_PROTOCOL_HWMP = 1, | |
| IEEE80211_PATH_PROTOCOL_VENDOR = 255, | |
| }; | |
| /** | |
| * enum ieee80211_mesh_path_metric - mesh path selection metric identifier | |
| * | |
| * @IEEE80211_PATH_METRIC_AIRTIME: the default path selection metric | |
| * @IEEE80211_PATH_METRIC_VENDOR: a vendor specific metric that will be | |
| * specified in a vendor specific information element | |
| */ | |
| enum ieee80211_mesh_path_metric { | |
| IEEE80211_PATH_METRIC_AIRTIME = 1, | |
| IEEE80211_PATH_METRIC_VENDOR = 255, | |
| }; | |
| /** | |
| * enum ieee80211_root_mode_identifier - root mesh STA mode identifier | |
| * | |
| * These attribute are used by dot11MeshHWMPRootMode to set root mesh STA mode | |
| * | |
| * @IEEE80211_ROOTMODE_NO_ROOT: the mesh STA is not a root mesh STA (default) | |
| * @IEEE80211_ROOTMODE_ROOT: the mesh STA is a root mesh STA if greater than | |
| * this value | |
| * @IEEE80211_PROACTIVE_PREQ_NO_PREP: the mesh STA is a root mesh STA supports | |
| * the proactive PREQ with proactive PREP subfield set to 0 | |
| * @IEEE80211_PROACTIVE_PREQ_WITH_PREP: the mesh STA is a root mesh STA | |
| * supports the proactive PREQ with proactive PREP subfield set to 1 | |
| * @IEEE80211_PROACTIVE_RANN: the mesh STA is a root mesh STA supports | |
| * the proactive RANN | |
| */ | |
| enum ieee80211_root_mode_identifier { | |
| IEEE80211_ROOTMODE_NO_ROOT = 0, | |
| IEEE80211_ROOTMODE_ROOT = 1, | |
| IEEE80211_PROACTIVE_PREQ_NO_PREP = 2, | |
| IEEE80211_PROACTIVE_PREQ_WITH_PREP = 3, | |
| IEEE80211_PROACTIVE_RANN = 4, | |
| }; | |
| /* | |
| * IEEE 802.11-2007 7.3.2.9 Country information element | |
| * | |
| * Minimum length is 8 octets, ie len must be evenly | |
| * divisible by 2 | |
| */ | |
| /* Although the spec says 8 I'm seeing 6 in practice */ | |
| #define IEEE80211_COUNTRY_IE_MIN_LEN 6 | |
| /* The Country String field of the element shall be 3 octets in length */ | |
| #define IEEE80211_COUNTRY_STRING_LEN 3 | |
| /* | |
| * For regulatory extension stuff see IEEE 802.11-2007 | |
| * Annex I (page 1141) and Annex J (page 1147). Also | |
| * review 7.3.2.9. | |
| * | |
| * When dot11RegulatoryClassesRequired is true and the | |
| * first_channel/reg_extension_id is >= 201 then the IE | |
| * compromises of the 'ext' struct represented below: | |
| * | |
| * - Regulatory extension ID - when generating IE this just needs | |
| * to be monotonically increasing for each triplet passed in | |
| * the IE | |
| * - Regulatory class - index into set of rules | |
| * - Coverage class - index into air propagation time (Table 7-27), | |
| * in microseconds, you can compute the air propagation time from | |
| * the index by multiplying by 3, so index 10 yields a propagation | |
| * of 10 us. Valid values are 0-31, values 32-255 are not defined | |
| * yet. A value of 0 inicates air propagation of <= 1 us. | |
| * | |
| * See also Table I.2 for Emission limit sets and table | |
| * I.3 for Behavior limit sets. Table J.1 indicates how to map | |
| * a reg_class to an emission limit set and behavior limit set. | |
| */ | |
| #define IEEE80211_COUNTRY_EXTENSION_ID 201 | |
| /* | |
| * Channels numbers in the IE must be monotonically increasing | |
| * if dot11RegulatoryClassesRequired is not true. | |
| * | |
| * If dot11RegulatoryClassesRequired is true consecutive | |
| * subband triplets following a regulatory triplet shall | |
| * have monotonically increasing first_channel number fields. | |
| * | |
| * Channel numbers shall not overlap. | |
| * | |
| * Note that max_power is signed. | |
| */ | |
| struct ieee80211_country_ie_triplet { | |
| union { | |
| struct { | |
| u8 first_channel; | |
| u8 num_channels; | |
| s8 max_power; | |
| } __packed chans; | |
| struct { | |
| u8 reg_extension_id; | |
| u8 reg_class; | |
| u8 coverage_class; | |
| } __packed ext; | |
| }; | |
| } __packed; | |
| enum ieee80211_timeout_interval_type { | |
| WLAN_TIMEOUT_REASSOC_DEADLINE = 1 /* 802.11r */, | |
| WLAN_TIMEOUT_KEY_LIFETIME = 2 /* 802.11r */, | |
| WLAN_TIMEOUT_ASSOC_COMEBACK = 3 /* 802.11w */, | |
| }; | |
| /** | |
| * struct ieee80211_timeout_interval_ie - Timeout Interval element | |
| * @type: type, see &enum ieee80211_timeout_interval_type | |
| * @value: timeout interval value | |
| */ | |
| struct ieee80211_timeout_interval_ie { | |
| u8 type; | |
| __le32 value; | |
| } __packed; | |
| /** | |
| * enum ieee80211_idle_options - BSS idle options | |
| * @WLAN_IDLE_OPTIONS_PROTECTED_KEEP_ALIVE: the station should send an RSN | |
| * protected frame to the AP to reset the idle timer at the AP for | |
| * the station. | |
| */ | |
| enum ieee80211_idle_options { | |
| WLAN_IDLE_OPTIONS_PROTECTED_KEEP_ALIVE = BIT(0), | |
| }; | |
| /** | |
| * struct ieee80211_bss_max_idle_period_ie | |
| * | |
| * This structure refers to "BSS Max idle period element" | |
| * | |
| * @max_idle_period: indicates the time period during which a station can | |
| * refrain from transmitting frames to its associated AP without being | |
| * disassociated. In units of 1000 TUs. | |
| * @idle_options: indicates the options associated with the BSS idle capability | |
| * as specified in &enum ieee80211_idle_options. | |
| */ | |
| struct ieee80211_bss_max_idle_period_ie { | |
| __le16 max_idle_period; | |
| u8 idle_options; | |
| } __packed; | |
| /* BACK action code */ | |
| enum ieee80211_back_actioncode { | |
| WLAN_ACTION_ADDBA_REQ = 0, | |
| WLAN_ACTION_ADDBA_RESP = 1, | |
| WLAN_ACTION_DELBA = 2, | |
| }; | |
| /* BACK (block-ack) parties */ | |
| enum ieee80211_back_parties { | |
| WLAN_BACK_RECIPIENT = 0, | |
| WLAN_BACK_INITIATOR = 1, | |
| }; | |
| /* SA Query action */ | |
| enum ieee80211_sa_query_action { | |
| WLAN_ACTION_SA_QUERY_REQUEST = 0, | |
| WLAN_ACTION_SA_QUERY_RESPONSE = 1, | |
| }; | |
| /** | |
| * struct ieee80211_bssid_index | |
| * | |
| * This structure refers to "Multiple BSSID-index element" | |
| * | |
| * @bssid_index: BSSID index | |
| * @dtim_period: optional, overrides transmitted BSS dtim period | |
| * @dtim_count: optional, overrides transmitted BSS dtim count | |
| */ | |
| struct ieee80211_bssid_index { | |
| u8 bssid_index; | |
| u8 dtim_period; | |
| u8 dtim_count; | |
| }; | |
| /** | |
| * struct ieee80211_multiple_bssid_configuration | |
| * | |
| * This structure refers to "Multiple BSSID Configuration element" | |
| * | |
| * @bssid_count: total number of active BSSIDs in the set | |
| * @profile_periodicity: the least number of beacon frames need to be received | |
| * in order to discover all the nontransmitted BSSIDs in the set. | |
| */ | |
| struct ieee80211_multiple_bssid_configuration { | |
| u8 bssid_count; | |
| u8 profile_periodicity; | |
| }; | |
| #define SUITE(oui, id) (((oui) << 8) | (id)) | |
| /* cipher suite selectors */ | |
| #define WLAN_CIPHER_SUITE_USE_GROUP SUITE(0x000FAC, 0) | |
| #define WLAN_CIPHER_SUITE_WEP40 SUITE(0x000FAC, 1) | |
| #define WLAN_CIPHER_SUITE_TKIP SUITE(0x000FAC, 2) | |
| /* reserved: SUITE(0x000FAC, 3) */ | |
| #define WLAN_CIPHER_SUITE_CCMP SUITE(0x000FAC, 4) | |
| #define WLAN_CIPHER_SUITE_WEP104 SUITE(0x000FAC, 5) | |
| #define WLAN_CIPHER_SUITE_AES_CMAC SUITE(0x000FAC, 6) | |
| #define WLAN_CIPHER_SUITE_GCMP SUITE(0x000FAC, 8) | |
| #define WLAN_CIPHER_SUITE_GCMP_256 SUITE(0x000FAC, 9) | |
| #define WLAN_CIPHER_SUITE_CCMP_256 SUITE(0x000FAC, 10) | |
| #define WLAN_CIPHER_SUITE_BIP_GMAC_128 SUITE(0x000FAC, 11) | |
| #define WLAN_CIPHER_SUITE_BIP_GMAC_256 SUITE(0x000FAC, 12) | |
| #define WLAN_CIPHER_SUITE_BIP_CMAC_256 SUITE(0x000FAC, 13) | |
| #define WLAN_CIPHER_SUITE_SMS4 SUITE(0x001472, 1) | |
| /* AKM suite selectors */ | |
| #define WLAN_AKM_SUITE_8021X SUITE(0x000FAC, 1) | |
| #define WLAN_AKM_SUITE_PSK SUITE(0x000FAC, 2) | |
| #define WLAN_AKM_SUITE_FT_8021X SUITE(0x000FAC, 3) | |
| #define WLAN_AKM_SUITE_FT_PSK SUITE(0x000FAC, 4) | |
| #define WLAN_AKM_SUITE_8021X_SHA256 SUITE(0x000FAC, 5) | |
| #define WLAN_AKM_SUITE_PSK_SHA256 SUITE(0x000FAC, 6) | |
| #define WLAN_AKM_SUITE_TDLS SUITE(0x000FAC, 7) | |
| #define WLAN_AKM_SUITE_SAE SUITE(0x000FAC, 8) | |
| #define WLAN_AKM_SUITE_FT_OVER_SAE SUITE(0x000FAC, 9) | |
| #define WLAN_AKM_SUITE_AP_PEER_KEY SUITE(0x000FAC, 10) | |
| #define WLAN_AKM_SUITE_8021X_SUITE_B SUITE(0x000FAC, 11) | |
| #define WLAN_AKM_SUITE_8021X_SUITE_B_192 SUITE(0x000FAC, 12) | |
| #define WLAN_AKM_SUITE_FT_8021X_SHA384 SUITE(0x000FAC, 13) | |
| #define WLAN_AKM_SUITE_FILS_SHA256 SUITE(0x000FAC, 14) | |
| #define WLAN_AKM_SUITE_FILS_SHA384 SUITE(0x000FAC, 15) | |
| #define WLAN_AKM_SUITE_FT_FILS_SHA256 SUITE(0x000FAC, 16) | |
| #define WLAN_AKM_SUITE_FT_FILS_SHA384 SUITE(0x000FAC, 17) | |
| #define WLAN_AKM_SUITE_OWE SUITE(0x000FAC, 18) | |
| #define WLAN_AKM_SUITE_FT_PSK_SHA384 SUITE(0x000FAC, 19) | |
| #define WLAN_AKM_SUITE_PSK_SHA384 SUITE(0x000FAC, 20) | |
| #define WLAN_MAX_KEY_LEN 32 | |
| #define WLAN_PMK_NAME_LEN 16 | |
| #define WLAN_PMKID_LEN 16 | |
| #define WLAN_PMK_LEN_EAP_LEAP 16 | |
| #define WLAN_PMK_LEN 32 | |
| #define WLAN_PMK_LEN_SUITE_B_192 48 | |
| #define WLAN_OUI_WFA 0x506f9a | |
| #define WLAN_OUI_TYPE_WFA_P2P 9 | |
| #define WLAN_OUI_MICROSOFT 0x0050f2 | |
| #define WLAN_OUI_TYPE_MICROSOFT_WPA 1 | |
| #define WLAN_OUI_TYPE_MICROSOFT_WMM 2 | |
| #define WLAN_OUI_TYPE_MICROSOFT_WPS 4 | |
| #define WLAN_OUI_TYPE_MICROSOFT_TPC 8 | |
| /* | |
| * WMM/802.11e Tspec Element | |
| */ | |
| #define IEEE80211_WMM_IE_TSPEC_TID_MASK 0x0F | |
| #define IEEE80211_WMM_IE_TSPEC_TID_SHIFT 1 | |
| enum ieee80211_tspec_status_code { | |
| IEEE80211_TSPEC_STATUS_ADMISS_ACCEPTED = 0, | |
| IEEE80211_TSPEC_STATUS_ADDTS_INVAL_PARAMS = 0x1, | |
| }; | |
| struct ieee80211_tspec_ie { | |
| u8 element_id; | |
| u8 len; | |
| u8 oui[3]; | |
| u8 oui_type; | |
| u8 oui_subtype; | |
| u8 version; | |
| __le16 tsinfo; | |
| u8 tsinfo_resvd; | |
| __le16 nominal_msdu; | |
| __le16 max_msdu; | |
| __le32 min_service_int; | |
| __le32 max_service_int; | |
| __le32 inactivity_int; | |
| __le32 suspension_int; | |
| __le32 service_start_time; | |
| __le32 min_data_rate; | |
| __le32 mean_data_rate; | |
| __le32 peak_data_rate; | |
| __le32 max_burst_size; | |
| __le32 delay_bound; | |
| __le32 min_phy_rate; | |
| __le16 sba; | |
| __le16 medium_time; | |
| } __packed; | |
| struct ieee80211_he_6ghz_capa { | |
| /* uses IEEE80211_HE_6GHZ_CAP_* below */ | |
| __le16 capa; | |
| } __packed; | |
| /* HE 6 GHz band capabilities */ | |
| /* uses enum ieee80211_min_mpdu_spacing values */ | |
| #define IEEE80211_HE_6GHZ_CAP_MIN_MPDU_START 0x0007 | |
| /* uses enum ieee80211_vht_max_ampdu_length_exp values */ | |
| #define IEEE80211_HE_6GHZ_CAP_MAX_AMPDU_LEN_EXP 0x0038 | |
| /* uses IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_* values */ | |
| #define IEEE80211_HE_6GHZ_CAP_MAX_MPDU_LEN 0x00c0 | |
| /* WLAN_HT_CAP_SM_PS_* values */ | |
| #define IEEE80211_HE_6GHZ_CAP_SM_PS 0x0600 | |
| #define IEEE80211_HE_6GHZ_CAP_RD_RESPONDER 0x0800 | |
| #define IEEE80211_HE_6GHZ_CAP_RX_ANTPAT_CONS 0x1000 | |
| #define IEEE80211_HE_6GHZ_CAP_TX_ANTPAT_CONS 0x2000 | |
| /** | |
| * ieee80211_get_qos_ctl - get pointer to qos control bytes | |
| * @hdr: the frame | |
| * | |
| * The qos ctrl bytes come after the frame_control, duration, seq_num | |
| * and 3 or 4 addresses of length ETH_ALEN. | |
| * 3 addr: 2 + 2 + 2 + 3*6 = 24 | |
| * 4 addr: 2 + 2 + 2 + 4*6 = 30 | |
| */ | |
| static inline u8 *ieee80211_get_qos_ctl(struct ieee80211_hdr *hdr) | |
| { | |
| if (ieee80211_has_a4(hdr->frame_control)) | |
| return (u8 *)hdr + 30; | |
| else | |
| return (u8 *)hdr + 24; | |
| } | |
| /** | |
| * ieee80211_get_tid - get qos TID | |
| * @hdr: the frame | |
| */ | |
| static inline u8 ieee80211_get_tid(struct ieee80211_hdr *hdr) | |
| { | |
| u8 *qc = ieee80211_get_qos_ctl(hdr); | |
| return qc[0] & IEEE80211_QOS_CTL_TID_MASK; | |
| } | |
| /** | |
| * ieee80211_get_SA - get pointer to SA | |
| * @hdr: the frame | |
| * | |
| * Given an 802.11 frame, this function returns the offset | |
| * to the source address (SA). It does not verify that the | |
| * header is long enough to contain the address, and the | |
| * header must be long enough to contain the frame control | |
| * field. | |
| */ | |
| static inline u8 *ieee80211_get_SA(struct ieee80211_hdr *hdr) | |
| { | |
| if (ieee80211_has_a4(hdr->frame_control)) | |
| return hdr->addr4; | |
| if (ieee80211_has_fromds(hdr->frame_control)) | |
| return hdr->addr3; | |
| return hdr->addr2; | |
| } | |
| /** | |
| * ieee80211_get_DA - get pointer to DA | |
| * @hdr: the frame | |
| * | |
| * Given an 802.11 frame, this function returns the offset | |
| * to the destination address (DA). It does not verify that | |
| * the header is long enough to contain the address, and the | |
| * header must be long enough to contain the frame control | |
| * field. | |
| */ | |
| static inline u8 *ieee80211_get_DA(struct ieee80211_hdr *hdr) | |
| { | |
| if (ieee80211_has_tods(hdr->frame_control)) | |
| return hdr->addr3; | |
| else | |
| return hdr->addr1; | |
| } | |
| /** | |
| * _ieee80211_is_robust_mgmt_frame - check if frame is a robust management frame | |
| * @hdr: the frame (buffer must include at least the first octet of payload) | |
| */ | |
| static inline bool _ieee80211_is_robust_mgmt_frame(struct ieee80211_hdr *hdr) | |
| { | |
| if (ieee80211_is_disassoc(hdr->frame_control) || | |
| ieee80211_is_deauth(hdr->frame_control)) | |
| return true; | |
| if (ieee80211_is_action(hdr->frame_control)) { | |
| u8 *category; | |
| /* | |
| * Action frames, excluding Public Action frames, are Robust | |
| * Management Frames. However, if we are looking at a Protected | |
| * frame, skip the check since the data may be encrypted and | |
| * the frame has already been found to be a Robust Management | |
| * Frame (by the other end). | |
| */ | |
| if (ieee80211_has_protected(hdr->frame_control)) | |
| return true; | |
| category = ((u8 *) hdr) + 24; | |
| return *category != WLAN_CATEGORY_PUBLIC && | |
| *category != WLAN_CATEGORY_HT && | |
| *category != WLAN_CATEGORY_WNM_UNPROTECTED && | |
| *category != WLAN_CATEGORY_SELF_PROTECTED && | |
| *category != WLAN_CATEGORY_UNPROT_DMG && | |
| *category != WLAN_CATEGORY_VHT && | |
| *category != WLAN_CATEGORY_VENDOR_SPECIFIC; | |
| } | |
| return false; | |
| } | |
| /** | |
| * ieee80211_is_robust_mgmt_frame - check if skb contains a robust mgmt frame | |
| * @skb: the skb containing the frame, length will be checked | |
| */ | |
| static inline bool ieee80211_is_robust_mgmt_frame(struct sk_buff *skb) | |
| { | |
| if (skb->len < IEEE80211_MIN_ACTION_SIZE) | |
| return false; | |
| return _ieee80211_is_robust_mgmt_frame((void *)skb->data); | |
| } | |
| /** | |
| * ieee80211_is_public_action - check if frame is a public action frame | |
| * @hdr: the frame | |
| * @len: length of the frame | |
| */ | |
| static inline bool ieee80211_is_public_action(struct ieee80211_hdr *hdr, | |
| size_t len) | |
| { | |
| struct ieee80211_mgmt *mgmt = (void *)hdr; | |
| if (len < IEEE80211_MIN_ACTION_SIZE) | |
| return false; | |
| if (!ieee80211_is_action(hdr->frame_control)) | |
| return false; | |
| return mgmt->u.action.category == WLAN_CATEGORY_PUBLIC; | |
| } | |
| /** | |
| * _ieee80211_is_group_privacy_action - check if frame is a group addressed | |
| * privacy action frame | |
| * @hdr: the frame | |
| */ | |
| static inline bool _ieee80211_is_group_privacy_action(struct ieee80211_hdr *hdr) | |
| { | |
| struct ieee80211_mgmt *mgmt = (void *)hdr; | |
| if (!ieee80211_is_action(hdr->frame_control) || | |
| !is_multicast_ether_addr(hdr->addr1)) | |
| return false; | |
| return mgmt->u.action.category == WLAN_CATEGORY_MESH_ACTION || | |
| mgmt->u.action.category == WLAN_CATEGORY_MULTIHOP_ACTION; | |
| } | |
| /** | |
| * ieee80211_is_group_privacy_action - check if frame is a group addressed | |
| * privacy action frame | |
| * @skb: the skb containing the frame, length will be checked | |
| */ | |
| static inline bool ieee80211_is_group_privacy_action(struct sk_buff *skb) | |
| { | |
| if (skb->len < IEEE80211_MIN_ACTION_SIZE) | |
| return false; | |
| return _ieee80211_is_group_privacy_action((void *)skb->data); | |
| } | |
| /** | |
| * ieee80211_tu_to_usec - convert time units (TU) to microseconds | |
| * @tu: the TUs | |
| */ | |
| static inline unsigned long ieee80211_tu_to_usec(unsigned long tu) | |
| { | |
| return 1024 * tu; | |
| } | |
| /** | |
| * ieee80211_check_tim - check if AID bit is set in TIM | |
| * @tim: the TIM IE | |
| * @tim_len: length of the TIM IE | |
| * @aid: the AID to look for | |
| */ | |
| static inline bool ieee80211_check_tim(const struct ieee80211_tim_ie *tim, | |
| u8 tim_len, u16 aid) | |
| { | |
| u8 mask; | |
| u8 index, indexn1, indexn2; | |
| if (unlikely(!tim || tim_len < sizeof(*tim))) | |
| return false; | |
| aid &= 0x3fff; | |
| index = aid / 8; | |
| mask = 1 << (aid & 7); | |
| indexn1 = tim->bitmap_ctrl & 0xfe; | |
| indexn2 = tim_len + indexn1 - 4; | |
| if (index < indexn1 || index > indexn2) | |
| return false; | |
| index -= indexn1; | |
| return !!(tim->virtual_map[index] & mask); | |
| } | |
| /** | |
| * ieee80211_get_tdls_action - get tdls packet action (or -1, if not tdls packet) | |
| * @skb: the skb containing the frame, length will not be checked | |
| * @hdr_size: the size of the ieee80211_hdr that starts at skb->data | |
| * | |
| * This function assumes the frame is a data frame, and that the network header | |
| * is in the correct place. | |
| */ | |
| static inline int ieee80211_get_tdls_action(struct sk_buff *skb, u32 hdr_size) | |
| { | |
| if (!skb_is_nonlinear(skb) && | |
| skb->len > (skb_network_offset(skb) + 2)) { | |
| /* Point to where the indication of TDLS should start */ | |
| const u8 *tdls_data = skb_network_header(skb) - 2; | |
| if (get_unaligned_be16(tdls_data) == ETH_P_TDLS && | |
| tdls_data[2] == WLAN_TDLS_SNAP_RFTYPE && | |
| tdls_data[3] == WLAN_CATEGORY_TDLS) | |
| return tdls_data[4]; | |
| } | |
| return -1; | |
| } | |
| /* convert time units */ | |
| #define TU_TO_JIFFIES(x) (usecs_to_jiffies((x) * 1024)) | |
| #define TU_TO_EXP_TIME(x) (jiffies + TU_TO_JIFFIES(x)) | |
| /* convert frequencies */ | |
| #define MHZ_TO_KHZ(freq) ((freq) * 1000) | |
| #define KHZ_TO_MHZ(freq) ((freq) / 1000) | |
| #define PR_KHZ(f) KHZ_TO_MHZ(f), f % 1000 | |
| #define KHZ_F "%d.%03d" | |
| /* convert powers */ | |
| #define DBI_TO_MBI(gain) ((gain) * 100) | |
| #define MBI_TO_DBI(gain) ((gain) / 100) | |
| #define DBM_TO_MBM(gain) ((gain) * 100) | |
| #define MBM_TO_DBM(gain) ((gain) / 100) | |
| /** | |
| * ieee80211_action_contains_tpc - checks if the frame contains TPC element | |
| * @skb: the skb containing the frame, length will be checked | |
| * | |
| * This function checks if it's either TPC report action frame or Link | |
| * Measurement report action frame as defined in IEEE Std. 802.11-2012 8.5.2.5 | |
| * and 8.5.7.5 accordingly. | |
| */ | |
| static inline bool ieee80211_action_contains_tpc(struct sk_buff *skb) | |
| { | |
| struct ieee80211_mgmt *mgmt = (void *)skb->data; | |
| if (!ieee80211_is_action(mgmt->frame_control)) | |
| return false; | |
| if (skb->len < IEEE80211_MIN_ACTION_SIZE + | |
| sizeof(mgmt->u.action.u.tpc_report)) | |
| return false; | |
| /* | |
| * TPC report - check that: | |
| * category = 0 (Spectrum Management) or 5 (Radio Measurement) | |
| * spectrum management action = 3 (TPC/Link Measurement report) | |
| * TPC report EID = 35 | |
| * TPC report element length = 2 | |
| * | |
| * The spectrum management's tpc_report struct is used here both for | |
| * parsing tpc_report and radio measurement's link measurement report | |
| * frame, since the relevant part is identical in both frames. | |
| */ | |
| if (mgmt->u.action.category != WLAN_CATEGORY_SPECTRUM_MGMT && | |
| mgmt->u.action.category != WLAN_CATEGORY_RADIO_MEASUREMENT) | |
| return false; | |
| /* both spectrum mgmt and link measurement have same action code */ | |
| if (mgmt->u.action.u.tpc_report.action_code != | |
| WLAN_ACTION_SPCT_TPC_RPRT) | |
| return false; | |
| if (mgmt->u.action.u.tpc_report.tpc_elem_id != WLAN_EID_TPC_REPORT || | |
| mgmt->u.action.u.tpc_report.tpc_elem_length != | |
| sizeof(struct ieee80211_tpc_report_ie)) | |
| return false; | |
| return true; | |
| } | |
| struct element { | |
| u8 id; | |
| u8 datalen; | |
| u8 data[]; | |
| } __packed; | |
| /* element iteration helpers */ | |
| #define for_each_element(_elem, _data, _datalen) \ | |
| for (_elem = (const struct element *)(_data); \ | |
| (const u8 *)(_data) + (_datalen) - (const u8 *)_elem >= \ | |
| (int)sizeof(*_elem) && \ | |
| (const u8 *)(_data) + (_datalen) - (const u8 *)_elem >= \ | |
| (int)sizeof(*_elem) + _elem->datalen; \ | |
| _elem = (const struct element *)(_elem->data + _elem->datalen)) | |
| #define for_each_element_id(element, _id, data, datalen) \ | |
| for_each_element(element, data, datalen) \ | |
| if (element->id == (_id)) | |
| #define for_each_element_extid(element, extid, _data, _datalen) \ | |
| for_each_element(element, _data, _datalen) \ | |
| if (element->id == WLAN_EID_EXTENSION && \ | |
| element->datalen > 0 && \ | |
| element->data[0] == (extid)) | |
| #define for_each_subelement(sub, element) \ | |
| for_each_element(sub, (element)->data, (element)->datalen) | |
| #define for_each_subelement_id(sub, id, element) \ | |
| for_each_element_id(sub, id, (element)->data, (element)->datalen) | |
| #define for_each_subelement_extid(sub, extid, element) \ | |
| for_each_element_extid(sub, extid, (element)->data, (element)->datalen) | |
| /** | |
| * for_each_element_completed - determine if element parsing consumed all data | |
| * @element: element pointer after for_each_element() or friends | |
| * @data: same data pointer as passed to for_each_element() or friends | |
| * @datalen: same data length as passed to for_each_element() or friends | |
| * | |
| * This function returns %true if all the data was parsed or considered | |
| * while walking the elements. Only use this if your for_each_element() | |
| * loop cannot be broken out of, otherwise it always returns %false. | |
| * | |
| * If some data was malformed, this returns %false since the last parsed | |
| * element will not fill the whole remaining data. | |
| */ | |
| static inline bool for_each_element_completed(const struct element *element, | |
| const void *data, size_t datalen) | |
| { | |
| return (const u8 *)element == (const u8 *)data + datalen; | |
| } | |
| /** | |
| * RSNX Capabilities: | |
| * bits 0-3: Field length (n-1) | |
| */ | |
| #define WLAN_RSNX_CAPA_PROTECTED_TWT BIT(4) | |
| #define WLAN_RSNX_CAPA_SAE_H2E BIT(5) | |
| /* | |
| * reduced neighbor report, based on Draft P802.11ax_D5.0, | |
| * section 9.4.2.170 | |
| */ | |
| #define IEEE80211_AP_INFO_TBTT_HDR_TYPE 0x03 | |
| #define IEEE80211_AP_INFO_TBTT_HDR_FILTERED 0x04 | |
| #define IEEE80211_AP_INFO_TBTT_HDR_COLOC 0x08 | |
| #define IEEE80211_AP_INFO_TBTT_HDR_COUNT 0xF0 | |
| #define IEEE80211_TBTT_INFO_OFFSET_BSSID_BSS_PARAM 8 | |
| #define IEEE80211_TBTT_INFO_OFFSET_BSSID_SSSID_BSS_PARAM 12 | |
| #define IEEE80211_RNR_TBTT_PARAMS_OCT_RECOMMENDED 0x01 | |
| #define IEEE80211_RNR_TBTT_PARAMS_SAME_SSID 0x02 | |
| #define IEEE80211_RNR_TBTT_PARAMS_MULTI_BSSID 0x04 | |
| #define IEEE80211_RNR_TBTT_PARAMS_TRANSMITTED_BSSID 0x08 | |
| #define IEEE80211_RNR_TBTT_PARAMS_COLOC_ESS 0x10 | |
| #define IEEE80211_RNR_TBTT_PARAMS_PROBE_ACTIVE 0x20 | |
| #define IEEE80211_RNR_TBTT_PARAMS_COLOC_AP 0x40 | |
| struct ieee80211_neighbor_ap_info { | |
| u8 tbtt_info_hdr; | |
| u8 tbtt_info_len; | |
| u8 op_class; | |
| u8 channel; | |
| } __packed; | |
| #endif /* LINUX_IEEE80211_H */ |