blob: bd4450dbdcb61a55e32ae0d211b95203f9048a6c [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0
/*
* Samsung's S5PV210 based Galaxy Aries board device tree source
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include "s5pv210.dtsi"
/ {
compatible = "samsung,aries", "samsung,s5pv210";
aliases: aliases {
i2c4 = &i2c_sound;
i2c5 = &i2c_accel;
i2c6 = &i2c_pmic;
i2c7 = &i2c_musb;
i2c9 = &i2c_fuel;
i2c10 = &i2c_touchkey;
i2c11 = &i2c_prox;
i2c12 = &i2c_magnetometer;
};
memory@30000000 {
device_type = "memory";
reg = <0x30000000 0x05000000
0x40000000 0x10000000
0x50000000 0x08000000>;
};
reserved-memory {
#address-cells = <1>;
#size-cells = <1>;
ranges;
mfc_left: region@43000000 {
compatible = "shared-dma-pool";
no-map;
reg = <0x43000000 0x2000000>;
};
mfc_right: region@51000000 {
compatible = "shared-dma-pool";
no-map;
reg = <0x51000000 0x2000000>;
};
};
pmic_ap_clk: clock-0 {
/* Workaround for missing clock on PMIC */
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
};
bt_codec: bt_sco {
compatible = "linux,bt-sco";
#sound-dai-cells = <0>;
};
vibrator_pwr: regulator-fixed-0 {
compatible = "regulator-fixed";
regulator-name = "vibrator-en";
enable-active-high;
gpio = <&gpj1 1 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&vibrator_ena>;
};
touchkey_vdd: regulator-fixed-1 {
compatible = "regulator-fixed";
regulator-name = "VTOUCH_3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
enable-active-high;
gpio = <&gpj3 2 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&touchkey_vdd_ena>;
};
gp2a_vled: regulator-fixed-2 {
compatible = "regulator-fixed";
regulator-name = "VLED";
enable-active-high;
gpio = <&gpj1 4 GPIO_ACTIVE_HIGH>;
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
pinctrl-names = "default";
pinctrl-0 = <&gp2a_power>;
};
wifi_pwrseq: wifi-pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpg1 2 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&wlan_gpio_rst>;
post-power-on-delay-ms = <500>;
power-off-delay-us = <500>;
};
i2c_sound: i2c-gpio-0 {
compatible = "i2c-gpio";
sda-gpios = <&mp05 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&mp05 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <2>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&sound_i2c_pins>;
wm8994: wm8994@1a {
compatible = "wlf,wm8994";
reg = <0x1a>;
#sound-dai-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
clocks = <&clocks MOUT_CLKOUT>;
clock-names = "MCLK1";
AVDD2-supply = <&buck3_reg>;
DBVDD-supply = <&buck3_reg>;
CPVDD-supply = <&buck3_reg>;
SPKVDD1-supply = <&buck3_reg>;
SPKVDD2-supply = <&buck3_reg>;
wlf,gpio-cfg = <0xa101 0x8100 0x0100 0x0100 0x8100
0xa101 0x0100 0x8100 0x0100 0x0100
0x0100>;
wlf,ldo1ena = <&gpf3 4 GPIO_ACTIVE_HIGH>;
wlf,ldo2ena = <&gpf3 4 GPIO_ACTIVE_HIGH>;
wlf,lineout1-se;
wlf,lineout2-se;
assigned-clocks = <&clocks MOUT_CLKOUT>;
assigned-clock-rates = <0>;
assigned-clock-parents = <&xusbxti>;
pinctrl-names = "default";
pinctrl-0 = <&codec_ldo>;
};
};
i2c_accel: i2c-gpio-1 {
compatible = "i2c-gpio";
sda-gpios = <&gpj3 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpj3 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <2>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&accel_i2c_pins>;
accelerometer@38 {
compatible = "bosch,bma023";
reg = <0x38>;
vdd-supply = <&ldo9_reg>;
vddio-supply = <&ldo9_reg>;
};
};
i2c_pmic: i2c-gpio-2 {
compatible = "i2c-gpio";
sda-gpios = <&gpj4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpj4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <2>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&pmic_i2c_pins>;
pmic@66 {
compatible = "maxim,max8998";
reg = <0x66>;
interrupt-parent = <&gph0>;
interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
max8998,pmic-buck1-default-dvs-idx = <1>;
max8998,pmic-buck1-dvs-gpios = <&gph0 3 GPIO_ACTIVE_HIGH>,
<&gph0 4 GPIO_ACTIVE_HIGH>;
max8998,pmic-buck1-dvs-voltage = <1275000>, <1200000>,
<1050000>, <950000>;
max8998,pmic-buck2-default-dvs-idx = <0>;
max8998,pmic-buck2-dvs-gpio = <&gph0 5 GPIO_ACTIVE_HIGH>;
max8998,pmic-buck2-dvs-voltage = <1100000>, <1000000>;
pinctrl-names = "default";
pinctrl-0 = <&pmic_dvs_pins &pmic_irq>;
regulators {
ldo2_reg: LDO2 {
regulator-name = "VALIVE_1.2V";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
regulator-state-mem {
regulator-on-in-suspend;
};
};
ldo3_reg: LDO3 {
regulator-name = "VUSB_1.1V";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
ldo4_reg: LDO4 {
regulator-name = "VADC_3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
ldo5_reg: LDO5 {
regulator-name = "VTF_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
ldo6_reg: LDO6 {
regulator-name = "LDO6";
regulator-min-microvolt = <1600000>;
regulator-max-microvolt = <3600000>;
};
ldo7_reg: LDO7 {
regulator-name = "VLCD_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
ldo8_reg: LDO8 {
regulator-name = "VUSB_3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
ldo9_reg: LDO9 {
regulator-name = "VCC_2.8V_PDA";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-always-on;
};
ldo10_reg: LDO10 {
regulator-name = "VPLL_1.2V";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
regulator-state-mem {
regulator-on-in-suspend;
};
};
ldo11_reg: LDO11 {
regulator-name = "CAM_AF_3.0V";
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
ldo12_reg: LDO12 {
regulator-name = "CAM_SENSOR_CORE_1.2V";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
ldo13_reg: LDO13 {
regulator-name = "VGA_VDDIO_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
ldo14_reg: LDO14 {
regulator-name = "VGA_DVDD_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
ldo15_reg: LDO15 {
regulator-name = "CAM_ISP_HOST_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
ldo16_reg: LDO16 {
regulator-name = "VGA_AVDD_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
ldo17_reg: LDO17 {
regulator-name = "VCC_3.0V_LCD";
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
buck1_reg: BUCK1 {
regulator-name = "vddarm";
regulator-min-microvolt = <750000>;
regulator-max-microvolt = <1500000>;
regulator-state-mem {
regulator-off-in-suspend;
regulator-suspend-microvolt = <1250000>;
};
};
buck2_reg: BUCK2 {
regulator-name = "vddint";
regulator-min-microvolt = <750000>;
regulator-max-microvolt = <1500000>;
regulator-state-mem {
regulator-off-in-suspend;
regulator-suspend-microvolt = <1100000>;
};
};
buck3_reg: BUCK3 {
regulator-name = "VCC_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
buck4_reg: BUCK4 {
regulator-name = "CAM_ISP_CORE_1.2V";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
ap32khz_reg: EN32KHz-AP {
regulator-name = "32KHz AP";
regulator-always-on;
};
cp32khz_reg: EN32KHz-CP {
regulator-name = "32KHz CP";
};
vichg_reg: ENVICHG {
regulator-name = "VICHG";
regulator-always-on;
};
safe1_sreg: ESAFEOUT1 {
regulator-name = "SAFEOUT1";
};
safe2_sreg: ESAFEOUT2 {
regulator-name = "SAFEOUT2";
};
};
};
};
i2c_musb: i2c-gpio-3 {
compatible = "i2c-gpio";
sda-gpios = <&gpj3 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpj3 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <2>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&musb_i2c_pins>;
fsa9480: musb@25 {
compatible = "fcs,fsa9480";
reg = <0x25>;
interrupt-parent = <&gph2>;
interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
pinctrl-names = "default";
pinctrl-0 = <&musb_irq>;
};
};
i2c_fuel: i2c-gpio-4 {
compatible = "i2c-gpio";
sda-gpios = <&mp05 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&mp05 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <2>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&fg_i2c_pins>;
fg: fuelgauge@36 {
compatible = "maxim,max17040";
reg = <0x36>;
};
};
i2c_touchkey: i2c-gpio-5 {
compatible = "i2c-gpio";
sda-gpios = <&gpj3 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpj3 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <2>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&touchkey_i2c_pins>;
touchkey@20 {
compatible = "cypress,aries-touchkey";
reg = <0x20>;
vdd-supply = <&touchkey_vdd>;
vcc-supply = <&buck3_reg>;
linux,keycodes = <KEY_MENU KEY_BACK
KEY_HOMEPAGE KEY_SEARCH>;
interrupt-parent = <&gpj4>;
interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&touchkey_irq>;
};
};
i2c_prox: i2c-gpio-6 {
compatible = "i2c-gpio";
sda-gpios = <&gpg2 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpg0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <2>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&prox_i2c_pins>;
light-sensor@44 {
compatible = "sharp,gp2ap002a00f";
reg = <0x44>;
interrupt-parent = <&gph0>;
interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
vdd-supply = <&gp2a_vled>;
vio-supply = <&gp2a_vled>;
io-channels = <&gp2a_shunt>;
io-channel-names = "alsout";
sharp,proximity-far-hysteresis = /bits/ 8 <0x40>;
sharp,proximity-close-hysteresis = /bits/ 8 <0x20>;
pinctrl-names = "default";
pinctrl-0 = <&gp2a_irq>;
};
};
i2c_magnetometer: i2c-gpio-7 {
compatible = "i2c-gpio";
sda-gpios = <&gpj0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpj0 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <2>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&magnetometer_i2c_pins>;
status = "disabled";
/* Yamaha yas529 magnetometer, no mainline binding */
};
vibrator: pwm-vibrator {
compatible = "pwm-vibrator";
pwms = <&pwm 1 44642 0>;
pwm-names = "enable";
vcc-supply = <&vibrator_pwr>;
pinctrl-names = "default";
pinctrl-0 = <&pwm1_out>;
};
poweroff: syscon-poweroff {
compatible = "syscon-poweroff";
regmap = <&pmu_syscon>;
offset = <0x681c>; /* PS_HOLD_CONTROL */
value = <0x5200>;
};
spi_lcd: spi-2 {
compatible = "spi-gpio";
#address-cells = <1>;
#size-cells = <0>;
sck-gpios = <&mp04 1 GPIO_ACTIVE_HIGH>;
mosi-gpios = <&mp04 3 GPIO_ACTIVE_HIGH>;
cs-gpios = <&mp01 1 GPIO_ACTIVE_HIGH>;
num-chipselects = <1>;
pinctrl-names = "default";
pinctrl-0 = <&lcd_spi_pins>;
panel@0 {
compatible = "samsung,s6e63m0";
reg = <0>;
reset-gpios = <&mp05 5 GPIO_ACTIVE_LOW>;
vdd3-supply = <&ldo7_reg>;
vci-supply = <&ldo17_reg>;
spi-cs-high;
spi-max-frequency = <1200000>;
pinctrl-names = "default";
pinctrl-0 = <&panel_rst>;
port {
lcd_ep: endpoint {
remote-endpoint = <&fimd_ep>;
};
};
};
};
};
&adc {
vdd-supply = <&ldo4_reg>;
status = "okay";
gp2a_shunt: current-sense-shunt {
compatible = "current-sense-shunt";
io-channels = <&adc 9>;
shunt-resistor-micro-ohms = <47000000>; /* 47 ohms */
#io-channel-cells = <0>;
io-channel-ranges;
};
};
&fimd {
pinctrl-names = "default";
pinctrl-0 = <&lcd_clk &lcd_data24>;
status = "okay";
samsung,invert-vden;
samsung,invert-vclk;
#address-cells = <1>;
#size-cells = <0>;
port@3 {
reg = <3>;
fimd_ep: endpoint {
remote-endpoint = <&lcd_ep>;
};
};
};
&hsotg {
vusb_a-supply = <&ldo8_reg>;
vusb_d-supply = <&ldo3_reg>;
dr_mode = "peripheral";
status = "okay";
};
&i2c2 {
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <400000>;
samsung,i2c-slave-addr = <0x10>;
status = "okay";
touchscreen@4a {
compatible = "atmel,maxtouch";
reg = <0x4a>;
interrupt-parent = <&gpj0>;
interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
pinctrl-names = "default";
pinctrl-0 = <&ts_irq>;
reset-gpios = <&gpj1 3 GPIO_ACTIVE_HIGH>;
};
};
&i2s0 {
dmas = <&pdma0 9>, <&pdma0 10>, <&pdma0 11>;
status = "okay";
};
&mfc {
memory-region = <&mfc_left>, <&mfc_right>;
};
&pinctrl0 {
bt_reset: bt-reset {
samsung,pins = "gpb-3";
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
wlan_bt_en: wlan-bt-en {
samsung,pins = "gpb-5";
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-val = <1>;
};
codec_ldo: codec-ldo {
samsung,pins = "gpf3-4";
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
};
prox_i2c_pins: gp2a-i2c-pins {
samsung,pins = "gpg0-2", "gpg2-2";
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
wlan_gpio_rst: wlan-gpio-rst {
samsung,pins = "gpg1-2";
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
};
bt_wake: bt-wake {
samsung,pins = "gpg3-4";
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
};
gp2a_irq: gp2a-irq {
samsung,pins = "gph0-2";
samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
pmic_dvs_pins: pmic-dvs-pins {
samsung,pins = "gph0-3", "gph0-4", "gph0-5";
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
samsung,pin-val = <0>;
};
pmic_irq: pmic-irq {
samsung,pins = "gph0-7";
samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
wifi_host_wake: wifi-host-wake {
samsung,pins = "gph2-4";
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
bt_host_wake: bt-host-wake {
samsung,pins = "gph2-5";
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
musb_irq: musq-irq {
samsung,pins = "gph2-7";
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
tf_detect: tf-detect {
samsung,pins = "gph3-4";
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
wifi_wake: wifi-wake {
samsung,pins = "gph3-5";
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
};
magnetometer_i2c_pins: yas529-i2c-pins {
samsung,pins = "gpj0-0", "gpj0-1";
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
ts_irq: ts-irq {
samsung,pins = "gpj0-5";
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
vibrator_ena: vibrator-ena {
samsung,pins = "gpj1-1";
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
gp2a_power: gp2a-power {
samsung,pins = "gpj1-4";
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
touchkey_i2c_pins: touchkey-i2c-pins {
samsung,pins = "gpj3-0", "gpj3-1";
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
touchkey_vdd_ena: touchkey-vdd-ena {
samsung,pins = "gpj3-2";
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
musb_i2c_pins: musb-i2c-pins {
samsung,pins = "gpj3-4", "gpj3-5";
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
accel_i2c_pins: accel-i2c-pins {
samsung,pins = "gpj3-6", "gpj3-7";
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
pmic_i2c_pins: pmic-i2c-pins {
samsung,pins = "gpj4-0", "gpj4-3";
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
touchkey_irq: touchkey-irq {
samsung,pins = "gpj4-1";
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
lcd_spi_pins: spi-lcd-pins {
samsung,pins = "mp01-1", "mp04-1", "mp04-3";
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
fg_i2c_pins: fg-i2c-pins {
samsung,pins = "mp05-0", "mp05-1";
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
sound_i2c_pins: sound-i2c-pins {
samsung,pins = "mp05-2", "mp05-3";
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
panel_rst: panel-rst {
samsung,pins = "mp05-5";
samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
};
};
&pwm {
samsung,pwm-outputs = <1>;
};
&rtc {
clocks = <&clocks CLK_RTC>, <&pmic_ap_clk>;
clock-names = "rtc", "rtc_src";
};
&sdhci1 {
#address-cells = <1>;
#size-cells = <0>;
bus-width = <4>;
max-frequency = <38400000>;
pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_bus4 &wifi_wake &wifi_host_wake &wlan_bt_en>;
pinctrl-names = "default";
cap-sd-highspeed;
cap-mmc-highspeed;
keep-power-in-suspend;
mmc-pwrseq = <&wifi_pwrseq>;
non-removable;
status = "okay";
assigned-clocks = <&clocks MOUT_MMC1>, <&clocks SCLK_MMC1>;
assigned-clock-rates = <0>, <50000000>;
assigned-clock-parents = <&clocks MOUT_MPLL>;
wlan@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
interrupt-parent = <&gph2>;
interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "host-wake";
};
};
&sdhci2 {
bus-width = <4>;
cd-gpios = <&gph3 4 GPIO_ACTIVE_LOW>;
vmmc-supply = <&ldo5_reg>;
pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &tf_detect>;
pinctrl-names = "default";
status = "okay";
assigned-clocks = <&clocks MOUT_MMC2>, <&clocks SCLK_MMC2>;
assigned-clock-rates = <0>, <50000000>;
assigned-clock-parents = <&clocks MOUT_MPLL>;
};
&uart0 {
assigned-clocks = <&clocks MOUT_UART0>, <&clocks SCLK_UART0>;
assigned-clock-rates = <0>, <111166667>;
assigned-clock-parents = <&clocks MOUT_MPLL>;
status = "okay";
bluetooth {
compatible = "brcm,bcm4329-bt";
max-speed = <3000000>;
pinctrl-names = "default";
pinctrl-0 = <&uart0_data &uart0_fctl &bt_host_wake
&bt_reset &bt_wake>;
shutdown-gpios = <&gpb 3 GPIO_ACTIVE_HIGH>;
device-wakeup-gpios = <&gpg3 4 GPIO_ACTIVE_HIGH>;
interrupt-parent = <&gph2>;
interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "host-wake";
};
};
&uart1 {
status = "okay";
};
&uart2 {
status = "okay";
};
&usbphy {
status = "okay";
vbus-supply = <&safe1_sreg>;
};
&xusbxti {
clock-frequency = <24000000>;
};