blob: d5ded4f794df48c698323ff440201b2b1037c364 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0-only
/dts-v1/;
#include <dt-bindings/input/input.h>
#include "omap443x.dtsi"
#include "motorola-cpcap-mapphone.dtsi"
/ {
chosen {
stdout-path = &uart3;
};
aliases {
display0 = &lcd0;
display1 = &hdmi0;
};
/*
* We seem to have only 1021 MB accessible, 1021 - 1022 is locked,
* then 1023 - 1024 seems to contain mbm.
*/
memory {
device_type = "memory";
reg = <0x80000000 0x3fd00000>; /* 1021 MB */
};
/* Poweroff GPIO probably connected to CPCAP */
gpio-poweroff {
compatible = "gpio-poweroff";
pinctrl-0 = <&poweroff_gpio>;
pinctrl-names = "default";
gpios = <&gpio2 18 GPIO_ACTIVE_LOW>; /* gpio50 */
};
hdmi0: connector {
compatible = "hdmi-connector";
pinctrl-0 = <&hdmi_hpd_gpio>;
pinctrl-names = "default";
label = "hdmi";
type = "d";
hpd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; /* gpio63 */
port {
hdmi_connector_in: endpoint {
remote-endpoint = <&hdmi_out>;
};
};
};
/*
* HDMI 5V regulator probably sourced from battery. Let's keep
* keep this as always enabled for HDMI to work until we've
* figured what the encoder chip is.
*/
hdmi_regulator: regulator-hdmi {
compatible = "regulator-fixed";
regulator-name = "hdmi";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio2 27 GPIO_ACTIVE_HIGH>; /* gpio59 */
enable-active-high;
regulator-always-on;
};
/* FS USB Host PHY on port 1 for mdm6600 */
fsusb1_phy: usb-phy@1 {
compatible = "motorola,mapphone-mdm6600";
pinctrl-0 = <&usb_mdm6600_pins>;
pinctrl-names = "default";
enable-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>; /* gpio_95 */
power-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* gpio_54 */
reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>; /* gpio_49 */
/* mode: gpio_148 gpio_149 */
motorola,mode-gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>,
<&gpio5 21 GPIO_ACTIVE_HIGH>;
/* cmd: gpio_103 gpio_104 gpio_142 */
motorola,cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>,
<&gpio4 8 GPIO_ACTIVE_HIGH>,
<&gpio5 14 GPIO_ACTIVE_HIGH>;
/* status: gpio_52 gpio_53 gpio_55 */
motorola,status-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>,
<&gpio2 21 GPIO_ACTIVE_HIGH>,
<&gpio2 23 GPIO_ACTIVE_HIGH>;
#phy-cells = <0>;
};
/* HS USB host TLL nop-phy on port 2 for w3glte */
hsusb2_phy: usb-phy@2 {
compatible = "usb-nop-xceiv";
#phy-cells = <0>;
};
/* LCD regulator from sw5 source */
lcd_regulator: regulator-lcd {
compatible = "regulator-fixed";
regulator-name = "lcd";
regulator-min-microvolt = <5050000>;
regulator-max-microvolt = <5050000>;
gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>; /* gpio96 */
enable-active-high;
vin-supply = <&sw5>;
};
/* This is probably coming straight from the battery.. */
wl12xx_vmmc: regulator-wl12xx {
compatible = "regulator-fixed";
regulator-name = "vwl1271";
regulator-min-microvolt = <1650000>;
regulator-max-microvolt = <1650000>;
gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; /* gpio94 */
startup-delay-us = <70000>;
enable-active-high;
};
gpio_keys {
compatible = "gpio-keys";
volume_down {
label = "Volume Down";
gpios = <&gpio5 26 GPIO_ACTIVE_LOW>; /* gpio154 */
linux,code = <KEY_VOLUMEDOWN>;
linux,can-disable;
/* Value above 7.95ms for no GPIO hardware debounce */
debounce-interval = <10>;
};
slider {
label = "Keypad Slide";
gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; /* gpio122 */
linux,input-type = <EV_SW>;
linux,code = <SW_KEYPAD_SLIDE>;
linux,can-disable;
/* Value above 7.95ms for no GPIO hardware debounce */
debounce-interval = <10>;
};
};
soundcard {
compatible = "audio-graph-card";
label = "Droid 4 Audio";
widgets =
"Speaker", "Earpiece",
"Speaker", "Loudspeaker",
"Headphone", "Headphone Jack",
"Microphone", "Internal Mic";
routing =
"Earpiece", "EP",
"Loudspeaker", "SPKR",
"Headphone Jack", "HSL",
"Headphone Jack", "HSR",
"MICR", "Internal Mic";
dais = <&mcbsp2_port>, <&mcbsp3_port>;
};
pwm8: dmtimer-pwm-8 {
pinctrl-names = "default";
pinctrl-0 = <&vibrator_direction_pin>;
compatible = "ti,omap-dmtimer-pwm";
#pwm-cells = <3>;
ti,timers = <&timer8>;
ti,clock-source = <0x01>;
};
pwm9: dmtimer-pwm-9 {
pinctrl-names = "default";
pinctrl-0 = <&vibrator_enable_pin>;
compatible = "ti,omap-dmtimer-pwm";
#pwm-cells = <3>;
ti,timers = <&timer9>;
ti,clock-source = <0x01>;
};
vibrator {
compatible = "pwm-vibrator";
pwms = <&pwm9 0 10000000 0>, <&pwm8 0 10000000 0>;
pwm-names = "enable", "direction";
direction-duty-cycle-ns = <10000000>;
};
backlight: backlight {
compatible = "led-backlight";
leds = <&backlight_led>;
brightness-levels = <31 63 95 127 159 191 223 255>;
default-brightness-level = <6>;
};
};
&dss {
status = "okay";
};
&dsi1 {
status = "okay";
vdd-supply = <&vcsi>;
port {
dsi1_out_ep: endpoint {
remote-endpoint = <&lcd0_in>;
lanes = <0 1 2 3 4 5>;
};
};
lcd0: panel@0 {
compatible = "motorola,droid4-panel", "panel-dsi-cm";
reg = <0>;
label = "lcd0";
vddi-supply = <&lcd_regulator>;
reset-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* gpio101 */
backlight = <&backlight>;
width-mm = <50>;
height-mm = <89>;
rotation = <90>;
panel-timing {
clock-frequency = <0>; /* Calculated by dsi */
hback-porch = <2>;
hactive = <540>;
hfront-porch = <0>;
hsync-len = <2>;
vback-porch = <1>;
vactive = <960>;
vfront-porch = <0>;
vsync-len = <1>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <1>;
};
port {
lcd0_in: endpoint {
remote-endpoint = <&dsi1_out_ep>;
};
};
};
};
&hdmi {
status = "okay";
pinctrl-0 = <&dss_hdmi_pins>;
pinctrl-names = "default";
vdda-supply = <&vdac>;
port {
hdmi_out: endpoint {
remote-endpoint = <&hdmi_connector_in>;
lanes = <1 0 3 2 5 4 7 6>;
};
};
};
/* Battery NVRAM on 1-wire handled by w1_ds250x driver */
&hdqw1w {
pinctrl-0 = <&hdq_pins>;
pinctrl-names = "default";
ti,mode = "1w";
};
&i2c1 {
tmp105@48 {
compatible = "ti,tmp105";
reg = <0x48>;
pinctrl-0 = <&tmp105_irq>;
pinctrl-names = "default";
/* kpd_row0.gpio_178 */
interrupts-extended = <&gpio6 18 IRQ_TYPE_EDGE_FALLING
&omap4_pmx_core 0x14e>;
interrupt-names = "irq", "wakeup";
wakeup-source;
};
};
&keypad {
keypad,num-rows = <8>;
keypad,num-columns = <8>;
linux,keymap = <
/* Row 1 */
MATRIX_KEY(0, 2, KEY_1)
MATRIX_KEY(0, 6, KEY_2)
MATRIX_KEY(2, 3, KEY_3)
MATRIX_KEY(0, 7, KEY_4)
MATRIX_KEY(0, 4, KEY_5)
MATRIX_KEY(5, 5, KEY_6)
MATRIX_KEY(0, 1, KEY_7)
MATRIX_KEY(0, 5, KEY_8)
MATRIX_KEY(0, 0, KEY_9)
MATRIX_KEY(1, 6, KEY_0)
/* Row 2 */
MATRIX_KEY(3, 4, KEY_APOSTROPHE)
MATRIX_KEY(7, 6, KEY_Q)
MATRIX_KEY(7, 7, KEY_W)
MATRIX_KEY(7, 2, KEY_E)
MATRIX_KEY(1, 0, KEY_R)
MATRIX_KEY(4, 4, KEY_T)
MATRIX_KEY(1, 2, KEY_Y)
MATRIX_KEY(6, 7, KEY_U)
MATRIX_KEY(2, 2, KEY_I)
MATRIX_KEY(5, 6, KEY_O)
MATRIX_KEY(3, 7, KEY_P)
MATRIX_KEY(6, 5, KEY_BACKSPACE)
/* Row 3 */
MATRIX_KEY(5, 4, KEY_TAB)
MATRIX_KEY(5, 7, KEY_A)
MATRIX_KEY(2, 7, KEY_S)
MATRIX_KEY(7, 0, KEY_D)
MATRIX_KEY(2, 6, KEY_F)
MATRIX_KEY(6, 2, KEY_G)
MATRIX_KEY(6, 6, KEY_H)
MATRIX_KEY(1, 4, KEY_J)
MATRIX_KEY(3, 1, KEY_K)
MATRIX_KEY(2, 1, KEY_L)
MATRIX_KEY(4, 6, KEY_ENTER)
/* Row 4 */
MATRIX_KEY(3, 6, KEY_LEFTSHIFT) /* KEY_CAPSLOCK */
MATRIX_KEY(6, 1, KEY_Z)
MATRIX_KEY(7, 4, KEY_X)
MATRIX_KEY(5, 1, KEY_C)
MATRIX_KEY(1, 7, KEY_V)
MATRIX_KEY(2, 4, KEY_B)
MATRIX_KEY(4, 1, KEY_N)
MATRIX_KEY(1, 1, KEY_M)
MATRIX_KEY(3, 5, KEY_COMMA)
MATRIX_KEY(5, 2, KEY_DOT)
MATRIX_KEY(6, 3, KEY_UP)
MATRIX_KEY(7, 3, KEY_OK)
/* Row 5 */
MATRIX_KEY(2, 5, KEY_LEFTCTRL) /* KEY_LEFTSHIFT */
MATRIX_KEY(4, 5, KEY_LEFTALT) /* SYM */
MATRIX_KEY(6, 0, KEY_MINUS)
MATRIX_KEY(4, 7, KEY_EQUAL)
MATRIX_KEY(1, 5, KEY_SPACE)
MATRIX_KEY(3, 2, KEY_SLASH)
MATRIX_KEY(4, 3, KEY_LEFT)
MATRIX_KEY(5, 3, KEY_DOWN)
MATRIX_KEY(3, 3, KEY_RIGHT)
/* Side buttons, KEY_VOLUMEDOWN and KEY_PWER are on CPCAP? */
MATRIX_KEY(5, 0, KEY_VOLUMEUP)
>;
};
&mmc1 {
vmmc-supply = <&vwlan2>;
bus-width = <4>;
cd-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>; /* gpio176 */
};
&mmc2 {
vmmc-supply = <&vsdio>;
bus-width = <8>;
ti,non-removable;
};
&mmc3 {
pinctrl-names = "default";
pinctrl-0 = <&mmc3_pins>;
vmmc-supply = <&wl12xx_vmmc>;
/* uart2_tx.sdmmc3_dat1 pad as wakeirq */
interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
&omap4_pmx_core 0xde>;
interrupt-names = "irq", "wakeup";
non-removable;
bus-width = <4>;
cap-power-off-card;
keep-power-in-suspend;
#address-cells = <1>;
#size-cells = <0>;
wlcore: wlcore@2 {
compatible = "ti,wl1285", "ti,wl1283";
reg = <2>;
/* gpio_100 with gpmc_wait2 pad as wakeirq */
interrupts-extended = <&gpio4 4 IRQ_TYPE_LEVEL_HIGH>,
<&omap4_pmx_core 0x4e>;
interrupt-names = "irq", "wakeup";
ref-clock-frequency = <26000000>;
tcxo-clock-frequency = <26000000>;
};
};
&i2c1 {
led-controller@38 {
compatible = "ti,lm3532";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x38>;
enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
ramp-up-us = <1024>;
ramp-down-us = <8193>;
backlight_led: led@0 {
reg = <0>;
led-sources = <2>;
ti,led-mode = <0>;
label = ":backlight";
};
led@1 {
reg = <1>;
led-sources = <1>;
ti,led-mode = <0>;
label = ":kbd_backlight";
};
};
};
&i2c2 {
touchscreen@4a {
compatible = "atmel,maxtouch";
reg = <0x4a>;
pinctrl-names = "default";
pinctrl-0 = <&touchscreen_pins>;
reset-gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>; /* gpio173 */
/* gpio_183 with sys_nirq2 pad as wakeup */
interrupts-extended = <&gpio6 23 IRQ_TYPE_LEVEL_LOW>,
<&omap4_pmx_core 0x160>;
interrupt-names = "irq", "wakeup";
wakeup-source;
};
isl29030@44 {
compatible = "isil,isl29030";
reg = <0x44>;
pinctrl-names = "default";
pinctrl-0 = <&als_proximity_pins>;
interrupt-parent = <&gpio6>;
interrupts = <17 IRQ_TYPE_LEVEL_LOW>; /* gpio177 */
};
};
&omap4_pmx_core {
/* hdmi_hpd.gpio_63 */
hdmi_hpd_gpio: pinmux_hdmi_hpd_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x098, PIN_INPUT | MUX_MODE3)
>;
};
hdq_pins: pinmux_hdq_pins {
pinctrl-single,pins = <
/* 0x4a100120 hdq_sio.hdq_sio aa27 */
OMAP4_IOPAD(0x120, PIN_INPUT | MUX_MODE0)
>;
};
/* hdmi_cec.hdmi_cec, hdmi_scl.hdmi_scl, hdmi_sda.hdmi_sda */
dss_hdmi_pins: pinmux_dss_hdmi_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0)
OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0)
OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0)
>;
};
/*
* Android uses PIN_OFF_INPUT_PULLDOWN | PIN_INPUT_PULLUP | MUX_MODE3
* for gpio_100, but the internal pull makes wlan flakey on some
* devices. Off mode value should be tested if we have off mode working
* later on.
*/
mmc3_pins: pinmux_mmc3_pins {
pinctrl-single,pins = <
/* 0x4a10008e gpmc_wait2.gpio_100 d23 */
OMAP4_IOPAD(0x08e, PIN_INPUT | MUX_MODE3)
/* 0x4a100102 abe_mcbsp1_dx.sdmmc3_dat2 ab25 */
OMAP4_IOPAD(0x102, PIN_INPUT_PULLUP | MUX_MODE1)
/* 0x4a100104 abe_mcbsp1_fsx.sdmmc3_dat3 ac27 */
OMAP4_IOPAD(0x104, PIN_INPUT_PULLUP | MUX_MODE1)
/* 0x4a100118 uart2_cts.sdmmc3_clk ab26 */
OMAP4_IOPAD(0x118, PIN_INPUT | MUX_MODE1)
/* 0x4a10011a uart2_rts.sdmmc3_cmd ab27 */
OMAP4_IOPAD(0x11a, PIN_INPUT_PULLUP | MUX_MODE1)
/* 0x4a10011c uart2_rx.sdmmc3_dat0 aa25 */
OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE1)
/* 0x4a10011e uart2_tx.sdmmc3_dat1 aa26 */
OMAP4_IOPAD(0x11e, PIN_INPUT_PULLUP | MUX_MODE1)
>;
};
/* gpmc_ncs0.gpio_50 */
poweroff_gpio: pinmux_poweroff_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x074, PIN_OUTPUT_PULLUP | MUX_MODE3)
>;
};
/* kpd_row0.gpio_178 */
tmp105_irq: pinmux_tmp105_irq {
pinctrl-single,pins = <
OMAP4_IOPAD(0x18e, PIN_INPUT_PULLUP | MUX_MODE3)
>;
};
usb_gpio_mux_sel1: pinmux_usb_gpio_mux_sel1_pins {
/* gpio_60 */
pinctrl-single,pins = <
OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3)
>;
};
touchscreen_pins: pinmux_touchscreen_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x180, PIN_OUTPUT | MUX_MODE3)
OMAP4_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE3)
>;
};
als_proximity_pins: pinmux_als_proximity_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x18c, PIN_INPUT_PULLUP | MUX_MODE3)
>;
};
usb_mdm6600_pins: pinmux_usb_mdm6600_pins {
pinctrl-single,pins = <
/* enable 0x4a1000d8 usbb1_ulpitll_dat7.gpio_95 ag16 */
OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3)
/* power 0x4a10007c gpmc_nwp.gpio_54 c25 */
OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3)
/* reset 0x4a100072 gpmc_a25.gpio_49 d20 */
OMAP4_IOPAD(0x072, PIN_OUTPUT | MUX_MODE3)
/* mode0/bpwake 0x4a10014e sdmmc5_dat1.gpio_148 af4 */
OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3)
/* mode1/apwake 0x4a100150 sdmmc5_dat2.gpio_149 ag3 */
OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3)
/* status0 0x4a10007e gpmc_clk.gpio_55 b22 */
OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3)
/* status1 0x4a10007a gpmc_ncs3.gpio_53 c22 */
OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3)
/* status2 0x4a100078 gpmc_ncs2.gpio_52 d21 */
OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3)
/* cmd0 0x4a100094 gpmc_ncs6.gpio_103 c24 */
OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3)
/* cmd1 0x4a100096 gpmc_ncs7.gpio_104 d24 */
OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3)
/* cmd2 0x4a100142 uart3_rts_sd.gpio_142 f28 */
OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3)
>;
};
usb_ulpi_pins: pinmux_usb_ulpi_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x196, MUX_MODE7)
OMAP4_IOPAD(0x198, MUX_MODE7)
OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE0)
OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0)
OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE0)
OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE0)
OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE0)
OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE0)
OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE0)
OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE0)
OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE0)
OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE0)
OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE0)
OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE0)
>;
};
/* usb0_otg_dp and usb0_otg_dm */
usb_utmi_pins: pinmux_usb_utmi_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x196, PIN_INPUT | MUX_MODE0)
OMAP4_IOPAD(0x198, PIN_INPUT | MUX_MODE0)
OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7)
>;
};
/*
* Note that the v3.0.8 stock userspace dynamically remuxes uart1
* rts pin probably for PM purposes to PIN_INPUT_PULLUP | MUX_MODE7
* when not used. If needed, we can add rts pin remux later based
* on power measurements.
*/
uart1_pins: pinmux_uart1_pins {
pinctrl-single,pins = <
/* 0x4a10013c mcspi1_cs2.uart1_cts ag23 */
OMAP4_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE1)
/* 0x4a10013e mcspi1_cs3.uart1_rts ah23 */
OMAP4_IOPAD(0x13e, MUX_MODE1)
/* 0x4a100140 uart3_cts_rctx.uart1_tx f27 */
OMAP4_IOPAD(0x140, PIN_OUTPUT | MUX_MODE1)
/* 0x4a1001ca dpm_emu14.uart1_rx aa3 */
OMAP4_IOPAD(0x1ca, PIN_INPUT_PULLUP | MUX_MODE2)
>;
};
/* uart3_tx_irtx and uart3_rx_irrx */
uart3_pins: pinmux_uart3_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x196, MUX_MODE7)
OMAP4_IOPAD(0x198, MUX_MODE7)
OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1ba, MUX_MODE2)
OMAP4_IOPAD(0x1bc, PIN_INPUT | MUX_MODE2)
OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7)
OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7)
>;
};
uart4_pins: pinmux_uart4_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x15c, PIN_INPUT | MUX_MODE0) /* uart4_rx */
OMAP4_IOPAD(0x15e, PIN_OUTPUT | MUX_MODE0) /* uart4_tx */
OMAP4_IOPAD(0x110, PIN_INPUT_PULLUP | MUX_MODE5) /* uart4_cts */
OMAP4_IOPAD(0x112, PIN_OUTPUT_PULLUP | MUX_MODE5) /* uart4_rts */
>;
};
mcbsp2_pins: pinmux_mcbsp2_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x0f6, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_clkx */
OMAP4_IOPAD(0x0f8, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_dr */
OMAP4_IOPAD(0x0fa, PIN_OUTPUT | MUX_MODE0) /* abe_mcbsp2_dx */
OMAP4_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_fsx */
>;
};
mcbsp3_pins: pinmux_mcbsp3_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x106, PIN_INPUT | MUX_MODE1) /* abe_mcbsp3_dr */
OMAP4_IOPAD(0x108, PIN_OUTPUT | MUX_MODE1) /* abe_mcbsp3_dx */
OMAP4_IOPAD(0x10a, PIN_INPUT | MUX_MODE1) /* abe_mcbsp3_clkx */
OMAP4_IOPAD(0x10c, PIN_INPUT | MUX_MODE1) /* abe_mcbsp3_fsx */
>;
};
vibrator_direction_pin: pinmux_vibrator_direction_pin {
pinctrl-single,pins = <
OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE1) /* dmtimer8_pwm_evt (gpio_27) */
>;
};
vibrator_enable_pin: pinmux_vibrator_enable_pin {
pinctrl-single,pins = <
OMAP4_IOPAD(0X1d0, PIN_OUTPUT | MUX_MODE1) /* dmtimer9_pwm_evt (gpio_28) */
>;
};
};
&omap4_pmx_wkup {
usb_gpio_mux_sel2: pinmux_usb_gpio_mux_sel2_pins {
/* gpio_wk0 */
pinctrl-single,pins = <
OMAP4_IOPAD(0x040, PIN_OUTPUT_PULLDOWN | MUX_MODE3)
>;
};
};
/* RNG is used by secure mode and not accessible */
&rng_target {
status = "disabled";
};
/* Configure pwm clock source for timers 8 & 9 */
&timer8 {
assigned-clocks = <&abe_clkctrl OMAP4_TIMER8_CLKCTRL 24>;
assigned-clock-parents = <&sys_clkin_ck>;
};
&timer9 {
assigned-clocks = <&l4_per_clkctrl OMAP4_TIMER9_CLKCTRL 24>;
assigned-clock-parents = <&sys_clkin_ck>;
};
/*
* The uart1 port is wired to mdm6600 with rts and cts. The modem uses gpio_149
* for wake-up events for both the USB PHY and the UART. We can use gpio_149
* pad as the shared wakeirq for the UART rather than the RX or CTS pad as we
* have gpio_149 trigger before the UART transfer starts.
*/
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>;
interrupts-extended = <&wakeupgen GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH
&omap4_pmx_core 0x110>;
uart-has-rtscts;
current-speed = <115200>;
};
&uart3 {
interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
&omap4_pmx_core 0x17c>;
};
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&uart4_pins>;
bluetooth {
compatible = "ti,wl1285-st";
enable-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>; /* gpio 174 */
max-speed = <3686400>;
};
};
&usbhsohci {
phys = <&fsusb1_phy>;
phy-names = "usb";
};
&usbhsehci {
phys = <&hsusb2_phy>;
};
&usbhshost {
port1-mode = "ohci-phy-4pin-dpdm";
port2-mode = "ehci-tll";
};
/* Internal UTMI+ PHY used for OTG, CPCAP ULPI PHY for detection and charger */
&usb_otg_hs {
interface-type = <1>;
mode = <3>;
/*
* Max 300 mA steps based on similar PMIC MC13783UG.pdf "Table 10-4.
* VBUS Regulator Main Characteristics". Binding uses 2 mA units.
*/
power = <150>;
};
&i2c4 {
ak8975: magnetometer@c {
compatible = "asahi-kasei,ak8975";
reg = <0x0c>;
vdd-supply = <&vhvio>;
interrupt-parent = <&gpio6>;
interrupts = <15 IRQ_TYPE_EDGE_RISING>; /* gpio175 */
rotation-matrix = "-1", "0", "0",
"0", "1", "0",
"0", "0", "-1";
};
lis3dh: accelerometer@18 {
compatible = "st,lis3dh-accel";
reg = <0x18>;
vdd-supply = <&vhvio>;
interrupt-parent = <&gpio2>;
interrupts = <2 IRQ_TYPE_EDGE_BOTH>; /* gpio34 */
rotation-matrix = "0", "-1", "0",
"1", "0", "0",
"0", "0", "1";
};
};
&mcbsp2 {
#sound-dai-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&mcbsp2_pins>;
status = "okay";
mcbsp2_port: port {
cpu_dai2: endpoint {
dai-format = "i2s";
remote-endpoint = <&cpcap_audio_codec0>;
frame-master = <&cpcap_audio_codec0>;
bitclock-master = <&cpcap_audio_codec0>;
};
};
};
&mcbsp3 {
#sound-dai-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&mcbsp3_pins>;
status = "okay";
mcbsp3_port: port {
cpu_dai3: endpoint {
dai-format = "dsp_a";
frame-master = <&cpcap_audio_codec1>;
bitclock-master = <&cpcap_audio_codec1>;
remote-endpoint = <&cpcap_audio_codec1>;
};
};
};
&cpcap_audio_codec0 {
remote-endpoint = <&cpu_dai2>;
};
&cpcap_audio_codec1 {
remote-endpoint = <&cpu_dai3>;
};