blob: 57974b8fab86fb9584e85f4f5b59389700f8a470 [file] [log] [blame]
/*
* BSD LICENSE
*
* Copyright(c) 2016 Broadcom. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* * Neither the name of Broadcom Corporation nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
/dts-v1/;
#include "bcm-nsp.dtsi"
#include <dt-bindings/gpio/gpio.h>
/ {
model = "NorthStar Plus SVK (BCM958625HR)";
compatible = "brcm,bcm58625", "brcm,nsp";
chosen {
stdout-path = "serial0:115200n8";
};
memory@60000000 {
device_type = "memory";
reg = <0x60000000 0x20000000>;
};
gpio-restart {
compatible = "gpio-restart";
gpios = <&gpioa 15 GPIO_ACTIVE_LOW>;
open-source;
priority = <200>;
};
sfp: sfp {
compatible = "sff,sfp";
i2c-bus = <&i2c0>;
mod-def0-gpios = <&gpioa 28 GPIO_ACTIVE_LOW>;
los-gpios = <&gpioa 24 GPIO_ACTIVE_HIGH>;
tx-fault-gpios = <&gpioa 30 GPIO_ACTIVE_HIGH>;
tx-disable-gpios = <&gpioa 26 GPIO_ACTIVE_HIGH>;
};
};
&i2c0 {
status = "okay";
};
&dma {
status = "okay";
};
&amac0 {
status = "okay";
};
&amac1 {
status = "okay";
};
&amac2 {
status = "okay";
};
&ehci0 {
status = "okay";
};
&nand_controller {
nand@0 {
compatible = "brcm,nandcs";
reg = <0>;
nand-on-flash-bbt;
#address-cells = <1>;
#size-cells = <1>;
nand-ecc-strength = <24>;
nand-ecc-step-size = <1024>;
brcm,nand-oob-sector-size = <27>;
partition@0 {
label = "nboot";
reg = <0x00000000 0x00200000>;
read-only;
};
partition@200000 {
label = "nenv";
reg = <0x00200000 0x00400000>;
};
partition@600000 {
label = "nsystem";
reg = <0x00600000 0x00a00000>;
};
partition@1000000 {
label = "nrootfs";
reg = <0x01000000 0x03000000>;
};
partition@4000000 {
label = "ncustfs";
reg = <0x04000000 0x3c000000>;
};
};
};
&ohci0 {
status = "okay";
};
&pcie0 {
status = "okay";
};
&pcie1 {
status = "okay";
};
&pinctrl {
pinctrl-names = "default";
pinctrl-0 = <&nand_sel>;
nand_sel: nand_sel {
function = "nand";
groups = "nand_grp";
};
};
&qspi {
bspi-sel = <0>;
flash: m25p80@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "m25p80";
reg = <0x0>;
spi-max-frequency = <12500000>;
m25p,fast-read;
spi-cpol;
spi-cpha;
partition@0 {
label = "boot";
reg = <0x00000000 0x000a0000>;
};
partition@a0000 {
label = "env";
reg = <0x000a0000 0x00060000>;
};
partition@100000 {
label = "system";
reg = <0x00100000 0x00600000>;
};
partition@700000 {
label = "rootfs";
reg = <0x00700000 0x01900000>;
};
};
};
&sata_phy0 {
status = "okay";
};
&sata_phy1 {
status = "okay";
};
&srab {
compatible = "brcm,bcm58625-srab", "brcm,nsp-srab";
status = "okay";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
label = "port0";
reg = <0>;
};
port@1 {
label = "port1";
reg = <1>;
};
port@2 {
label = "port2";
reg = <2>;
};
port@3 {
label = "port3";
reg = <3>;
};
port@4 {
label = "port4";
reg = <4>;
};
port@5 {
label = "sfp";
phy-mode = "sgmii";
reg = <5>;
sfp = <&sfp>;
managed = "in-band-status";
};
port@8 {
ethernet = <&amac2>;
label = "cpu";
reg = <8>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
};
&uart0 {
status = "okay";
};
&usb3_phy {
status = "okay";
};
&xhci {
status = "okay";
};