| // SPDX-License-Identifier: GPL-2.0-or-later | 
 | /* | 
 |  * Driver for MAX31730 3-Channel Remote Temperature Sensor | 
 |  * | 
 |  * Copyright (c) 2019 Guenter Roeck <linux@roeck-us.net> | 
 |  */ | 
 |  | 
 | #include <linux/bits.h> | 
 | #include <linux/err.h> | 
 | #include <linux/i2c.h> | 
 | #include <linux/init.h> | 
 | #include <linux/hwmon.h> | 
 | #include <linux/module.h> | 
 | #include <linux/of_device.h> | 
 | #include <linux/of.h> | 
 | #include <linux/slab.h> | 
 |  | 
 | /* Addresses scanned */ | 
 | static const unsigned short normal_i2c[] = { 0x1c, 0x1d, 0x1e, 0x1f, 0x4c, | 
 | 					     0x4d, 0x4e, 0x4f, I2C_CLIENT_END }; | 
 |  | 
 | /* The MAX31730 registers */ | 
 | #define MAX31730_REG_TEMP		0x00 | 
 | #define MAX31730_REG_CONF		0x13 | 
 | #define  MAX31730_STOP			BIT(7) | 
 | #define  MAX31730_EXTRANGE		BIT(1) | 
 | #define MAX31730_REG_TEMP_OFFSET	0x16 | 
 | #define  MAX31730_TEMP_OFFSET_BASELINE	0x77 | 
 | #define MAX31730_REG_OFFSET_ENABLE	0x17 | 
 | #define MAX31730_REG_TEMP_MAX		0x20 | 
 | #define MAX31730_REG_TEMP_MIN		0x30 | 
 | #define MAX31730_REG_STATUS_HIGH	0x32 | 
 | #define MAX31730_REG_STATUS_LOW		0x33 | 
 | #define MAX31730_REG_CHANNEL_ENABLE	0x35 | 
 | #define MAX31730_REG_TEMP_FAULT		0x36 | 
 |  | 
 | #define MAX31730_REG_MFG_ID		0x50 | 
 | #define  MAX31730_MFG_ID		0x4d | 
 | #define MAX31730_REG_MFG_REV		0x51 | 
 | #define  MAX31730_MFG_REV		0x01 | 
 |  | 
 | #define MAX31730_TEMP_MIN		(-128000) | 
 | #define MAX31730_TEMP_MAX		127937 | 
 |  | 
 | /* Each client has this additional data */ | 
 | struct max31730_data { | 
 | 	struct i2c_client	*client; | 
 | 	u8			orig_conf; | 
 | 	u8			current_conf; | 
 | 	u8			offset_enable; | 
 | 	u8			channel_enable; | 
 | }; | 
 |  | 
 | /*-----------------------------------------------------------------------*/ | 
 |  | 
 | static inline long max31730_reg_to_mc(s16 temp) | 
 | { | 
 | 	return DIV_ROUND_CLOSEST((temp >> 4) * 1000, 16); | 
 | } | 
 |  | 
 | static int max31730_write_config(struct max31730_data *data, u8 set_mask, | 
 | 				 u8 clr_mask) | 
 | { | 
 | 	u8 value; | 
 |  | 
 | 	clr_mask |= MAX31730_EXTRANGE; | 
 | 	value = data->current_conf & ~clr_mask; | 
 | 	value |= set_mask; | 
 |  | 
 | 	if (data->current_conf != value) { | 
 | 		s32 err; | 
 |  | 
 | 		err = i2c_smbus_write_byte_data(data->client, MAX31730_REG_CONF, | 
 | 						value); | 
 | 		if (err) | 
 | 			return err; | 
 | 		data->current_conf = value; | 
 | 	} | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int max31730_set_enable(struct i2c_client *client, int reg, | 
 | 			       u8 *confdata, int channel, bool enable) | 
 | { | 
 | 	u8 regval = *confdata; | 
 | 	int err; | 
 |  | 
 | 	if (enable) | 
 | 		regval |= BIT(channel); | 
 | 	else | 
 | 		regval &= ~BIT(channel); | 
 |  | 
 | 	if (regval != *confdata) { | 
 | 		err = i2c_smbus_write_byte_data(client, reg, regval); | 
 | 		if (err) | 
 | 			return err; | 
 | 		*confdata = regval; | 
 | 	} | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int max31730_set_offset_enable(struct max31730_data *data, int channel, | 
 | 				      bool enable) | 
 | { | 
 | 	return max31730_set_enable(data->client, MAX31730_REG_OFFSET_ENABLE, | 
 | 				   &data->offset_enable, channel, enable); | 
 | } | 
 |  | 
 | static int max31730_set_channel_enable(struct max31730_data *data, int channel, | 
 | 				       bool enable) | 
 | { | 
 | 	return max31730_set_enable(data->client, MAX31730_REG_CHANNEL_ENABLE, | 
 | 				   &data->channel_enable, channel, enable); | 
 | } | 
 |  | 
 | static int max31730_read(struct device *dev, enum hwmon_sensor_types type, | 
 | 			 u32 attr, int channel, long *val) | 
 | { | 
 | 	struct max31730_data *data = dev_get_drvdata(dev); | 
 | 	int regval, reg, offset; | 
 |  | 
 | 	if (type != hwmon_temp) | 
 | 		return -EINVAL; | 
 |  | 
 | 	switch (attr) { | 
 | 	case hwmon_temp_input: | 
 | 		if (!(data->channel_enable & BIT(channel))) | 
 | 			return -ENODATA; | 
 | 		reg = MAX31730_REG_TEMP + (channel * 2); | 
 | 		break; | 
 | 	case hwmon_temp_max: | 
 | 		reg = MAX31730_REG_TEMP_MAX + (channel * 2); | 
 | 		break; | 
 | 	case hwmon_temp_min: | 
 | 		reg = MAX31730_REG_TEMP_MIN; | 
 | 		break; | 
 | 	case hwmon_temp_enable: | 
 | 		*val = !!(data->channel_enable & BIT(channel)); | 
 | 		return 0; | 
 | 	case hwmon_temp_offset: | 
 | 		if (!channel) | 
 | 			return -EINVAL; | 
 | 		if (!(data->offset_enable & BIT(channel))) { | 
 | 			*val = 0; | 
 | 			return 0; | 
 | 		} | 
 | 		offset = i2c_smbus_read_byte_data(data->client, | 
 | 						  MAX31730_REG_TEMP_OFFSET); | 
 | 		if (offset < 0) | 
 | 			return offset; | 
 | 		*val = (offset - MAX31730_TEMP_OFFSET_BASELINE) * 125; | 
 | 		return 0; | 
 | 	case hwmon_temp_fault: | 
 | 		regval = i2c_smbus_read_byte_data(data->client, | 
 | 						  MAX31730_REG_TEMP_FAULT); | 
 | 		if (regval < 0) | 
 | 			return regval; | 
 | 		*val = !!(regval & BIT(channel)); | 
 | 		return 0; | 
 | 	case hwmon_temp_min_alarm: | 
 | 		regval = i2c_smbus_read_byte_data(data->client, | 
 | 						  MAX31730_REG_STATUS_LOW); | 
 | 		if (regval < 0) | 
 | 			return regval; | 
 | 		*val = !!(regval & BIT(channel)); | 
 | 		return 0; | 
 | 	case hwmon_temp_max_alarm: | 
 | 		regval = i2c_smbus_read_byte_data(data->client, | 
 | 						  MAX31730_REG_STATUS_HIGH); | 
 | 		if (regval < 0) | 
 | 			return regval; | 
 | 		*val = !!(regval & BIT(channel)); | 
 | 		return 0; | 
 | 	default: | 
 | 		return -EINVAL; | 
 | 	} | 
 | 	regval = i2c_smbus_read_word_swapped(data->client, reg); | 
 | 	if (regval < 0) | 
 | 		return regval; | 
 |  | 
 | 	*val = max31730_reg_to_mc(regval); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int max31730_write(struct device *dev, enum hwmon_sensor_types type, | 
 | 			  u32 attr, int channel, long val) | 
 | { | 
 | 	struct max31730_data *data = dev_get_drvdata(dev); | 
 | 	int reg, err; | 
 |  | 
 | 	if (type != hwmon_temp) | 
 | 		return -EINVAL; | 
 |  | 
 | 	switch (attr) { | 
 | 	case hwmon_temp_max: | 
 | 		reg = MAX31730_REG_TEMP_MAX + channel * 2; | 
 | 		break; | 
 | 	case hwmon_temp_min: | 
 | 		reg = MAX31730_REG_TEMP_MIN; | 
 | 		break; | 
 | 	case hwmon_temp_enable: | 
 | 		if (val != 0 && val != 1) | 
 | 			return -EINVAL; | 
 | 		return max31730_set_channel_enable(data, channel, val); | 
 | 	case hwmon_temp_offset: | 
 | 		val = clamp_val(val, -14875, 17000) + 14875; | 
 | 		val = DIV_ROUND_CLOSEST(val, 125); | 
 | 		err = max31730_set_offset_enable(data, channel, | 
 | 					val != MAX31730_TEMP_OFFSET_BASELINE); | 
 | 		if (err) | 
 | 			return err; | 
 | 		return i2c_smbus_write_byte_data(data->client, | 
 | 						 MAX31730_REG_TEMP_OFFSET, val); | 
 | 	default: | 
 | 		return -EINVAL; | 
 | 	} | 
 |  | 
 | 	val = clamp_val(val, MAX31730_TEMP_MIN, MAX31730_TEMP_MAX); | 
 | 	val = DIV_ROUND_CLOSEST(val << 4, 1000) << 4; | 
 |  | 
 | 	return i2c_smbus_write_word_swapped(data->client, reg, (u16)val); | 
 | } | 
 |  | 
 | static umode_t max31730_is_visible(const void *data, | 
 | 				   enum hwmon_sensor_types type, | 
 | 				   u32 attr, int channel) | 
 | { | 
 | 	switch (type) { | 
 | 	case hwmon_temp: | 
 | 		switch (attr) { | 
 | 		case hwmon_temp_input: | 
 | 		case hwmon_temp_min_alarm: | 
 | 		case hwmon_temp_max_alarm: | 
 | 		case hwmon_temp_fault: | 
 | 			return 0444; | 
 | 		case hwmon_temp_min: | 
 | 			return channel ? 0444 : 0644; | 
 | 		case hwmon_temp_offset: | 
 | 		case hwmon_temp_enable: | 
 | 		case hwmon_temp_max: | 
 | 			return 0644; | 
 | 		} | 
 | 		break; | 
 | 	default: | 
 | 		break; | 
 | 	} | 
 | 	return 0; | 
 | } | 
 |  | 
 | static const struct hwmon_channel_info *max31730_info[] = { | 
 | 	HWMON_CHANNEL_INFO(chip, | 
 | 			   HWMON_C_REGISTER_TZ), | 
 | 	HWMON_CHANNEL_INFO(temp, | 
 | 			   HWMON_T_INPUT | HWMON_T_MIN | HWMON_T_MAX | | 
 | 			   HWMON_T_ENABLE | | 
 | 			   HWMON_T_MIN_ALARM | HWMON_T_MAX_ALARM, | 
 | 			   HWMON_T_INPUT | HWMON_T_MIN | HWMON_T_MAX | | 
 | 			   HWMON_T_OFFSET | HWMON_T_ENABLE | | 
 | 			   HWMON_T_MIN_ALARM | HWMON_T_MAX_ALARM | | 
 | 			   HWMON_T_FAULT, | 
 | 			   HWMON_T_INPUT | HWMON_T_MIN | HWMON_T_MAX | | 
 | 			   HWMON_T_OFFSET | HWMON_T_ENABLE | | 
 | 			   HWMON_T_MIN_ALARM | HWMON_T_MAX_ALARM | | 
 | 			   HWMON_T_FAULT, | 
 | 			   HWMON_T_INPUT | HWMON_T_MIN | HWMON_T_MAX | | 
 | 			   HWMON_T_OFFSET | HWMON_T_ENABLE | | 
 | 			   HWMON_T_MIN_ALARM | HWMON_T_MAX_ALARM | | 
 | 			   HWMON_T_FAULT | 
 | 			   ), | 
 | 	NULL | 
 | }; | 
 |  | 
 | static const struct hwmon_ops max31730_hwmon_ops = { | 
 | 	.is_visible = max31730_is_visible, | 
 | 	.read = max31730_read, | 
 | 	.write = max31730_write, | 
 | }; | 
 |  | 
 | static const struct hwmon_chip_info max31730_chip_info = { | 
 | 	.ops = &max31730_hwmon_ops, | 
 | 	.info = max31730_info, | 
 | }; | 
 |  | 
 | static void max31730_remove(void *data) | 
 | { | 
 | 	struct max31730_data *max31730 = data; | 
 | 	struct i2c_client *client = max31730->client; | 
 |  | 
 | 	i2c_smbus_write_byte_data(client, MAX31730_REG_CONF, | 
 | 				  max31730->orig_conf); | 
 | } | 
 |  | 
 | static int | 
 | max31730_probe(struct i2c_client *client) | 
 | { | 
 | 	struct device *dev = &client->dev; | 
 | 	struct device *hwmon_dev; | 
 | 	struct max31730_data *data; | 
 | 	int status, err; | 
 |  | 
 | 	if (!i2c_check_functionality(client->adapter, | 
 | 			I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA)) | 
 | 		return -EIO; | 
 |  | 
 | 	data = devm_kzalloc(dev, sizeof(struct max31730_data), GFP_KERNEL); | 
 | 	if (!data) | 
 | 		return -ENOMEM; | 
 |  | 
 | 	data->client = client; | 
 |  | 
 | 	/* Cache original configuration and enable status */ | 
 | 	status = i2c_smbus_read_byte_data(client, MAX31730_REG_CHANNEL_ENABLE); | 
 | 	if (status < 0) | 
 | 		return status; | 
 | 	data->channel_enable = status; | 
 |  | 
 | 	status = i2c_smbus_read_byte_data(client, MAX31730_REG_OFFSET_ENABLE); | 
 | 	if (status < 0) | 
 | 		return status; | 
 | 	data->offset_enable = status; | 
 |  | 
 | 	status = i2c_smbus_read_byte_data(client, MAX31730_REG_CONF); | 
 | 	if (status < 0) | 
 | 		return status; | 
 | 	data->orig_conf = status; | 
 | 	data->current_conf = status; | 
 |  | 
 | 	err = max31730_write_config(data, | 
 | 				    data->channel_enable ? 0 : MAX31730_STOP, | 
 | 				    data->channel_enable ? MAX31730_STOP : 0); | 
 | 	if (err) | 
 | 		return err; | 
 |  | 
 | 	dev_set_drvdata(dev, data); | 
 |  | 
 | 	err = devm_add_action_or_reset(dev, max31730_remove, data); | 
 | 	if (err) | 
 | 		return err; | 
 |  | 
 | 	hwmon_dev = devm_hwmon_device_register_with_info(dev, client->name, | 
 | 							 data, | 
 | 							 &max31730_chip_info, | 
 | 							 NULL); | 
 | 	return PTR_ERR_OR_ZERO(hwmon_dev); | 
 | } | 
 |  | 
 | static const struct i2c_device_id max31730_ids[] = { | 
 | 	{ "max31730", 0, }, | 
 | 	{ } | 
 | }; | 
 | MODULE_DEVICE_TABLE(i2c, max31730_ids); | 
 |  | 
 | static const struct of_device_id __maybe_unused max31730_of_match[] = { | 
 | 	{ | 
 | 		.compatible = "maxim,max31730", | 
 | 	}, | 
 | 	{ }, | 
 | }; | 
 | MODULE_DEVICE_TABLE(of, max31730_of_match); | 
 |  | 
 | static bool max31730_check_reg_temp(struct i2c_client *client, | 
 | 				    int reg) | 
 | { | 
 | 	int regval; | 
 |  | 
 | 	regval = i2c_smbus_read_byte_data(client, reg + 1); | 
 | 	return regval < 0 || (regval & 0x0f); | 
 | } | 
 |  | 
 | /* Return 0 if detection is successful, -ENODEV otherwise */ | 
 | static int max31730_detect(struct i2c_client *client, | 
 | 			   struct i2c_board_info *info) | 
 | { | 
 | 	struct i2c_adapter *adapter = client->adapter; | 
 | 	int regval; | 
 | 	int i; | 
 |  | 
 | 	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA | | 
 | 				     I2C_FUNC_SMBUS_WORD_DATA)) | 
 | 		return -ENODEV; | 
 |  | 
 | 	regval = i2c_smbus_read_byte_data(client, MAX31730_REG_MFG_ID); | 
 | 	if (regval != MAX31730_MFG_ID) | 
 | 		return -ENODEV; | 
 | 	regval = i2c_smbus_read_byte_data(client, MAX31730_REG_MFG_REV); | 
 | 	if (regval != MAX31730_MFG_REV) | 
 | 		return -ENODEV; | 
 |  | 
 | 	/* lower 4 bit of temperature and limit registers must be 0 */ | 
 | 	if (max31730_check_reg_temp(client, MAX31730_REG_TEMP_MIN)) | 
 | 		return -ENODEV; | 
 |  | 
 | 	for (i = 0; i < 4; i++) { | 
 | 		if (max31730_check_reg_temp(client, MAX31730_REG_TEMP + i * 2)) | 
 | 			return -ENODEV; | 
 | 		if (max31730_check_reg_temp(client, | 
 | 					    MAX31730_REG_TEMP_MAX + i * 2)) | 
 | 			return -ENODEV; | 
 | 	} | 
 |  | 
 | 	strlcpy(info->type, "max31730", I2C_NAME_SIZE); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int __maybe_unused max31730_suspend(struct device *dev) | 
 | { | 
 | 	struct max31730_data *data = dev_get_drvdata(dev); | 
 |  | 
 | 	return max31730_write_config(data, MAX31730_STOP, 0); | 
 | } | 
 |  | 
 | static int __maybe_unused max31730_resume(struct device *dev) | 
 | { | 
 | 	struct max31730_data *data = dev_get_drvdata(dev); | 
 |  | 
 | 	return max31730_write_config(data, 0, MAX31730_STOP); | 
 | } | 
 |  | 
 | static SIMPLE_DEV_PM_OPS(max31730_pm_ops, max31730_suspend, max31730_resume); | 
 |  | 
 | static struct i2c_driver max31730_driver = { | 
 | 	.class		= I2C_CLASS_HWMON, | 
 | 	.driver = { | 
 | 		.name	= "max31730", | 
 | 		.of_match_table = of_match_ptr(max31730_of_match), | 
 | 		.pm	= &max31730_pm_ops, | 
 | 	}, | 
 | 	.probe_new	= max31730_probe, | 
 | 	.id_table	= max31730_ids, | 
 | 	.detect		= max31730_detect, | 
 | 	.address_list	= normal_i2c, | 
 | }; | 
 |  | 
 | module_i2c_driver(max31730_driver); | 
 |  | 
 | MODULE_AUTHOR("Guenter Roeck <linux@roeck-us.net>"); | 
 | MODULE_DESCRIPTION("MAX31730 driver"); | 
 | MODULE_LICENSE("GPL"); |