blob: 41d0de6a7027bbecf44e8f73e603c30d6bff0df8 [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright 2020 Gateworks Corporation
*/
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/phy/phy-imx8-pcie.h>
/ {
aliases {
ethernet1 = &eth1;
usb0 = &usbotg1;
usb1 = &usbotg2;
};
led-controller {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpio_leds>;
led-0 {
function = LED_FUNCTION_STATUS;
color = <LED_COLOR_ID_GREEN>;
gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>;
default-state = "on";
linux,default-trigger = "heartbeat";
};
led-1 {
function = LED_FUNCTION_STATUS;
color = <LED_COLOR_ID_RED>;
gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
};
pcie0_refclk: pcie0-refclk {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <100000000>;
};
pps {
compatible = "pps-gpio";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pps>;
gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
status = "okay";
};
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "3P3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
reg_usb_otg1_vbus: regulator-usb-otg1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_reg_usb1_en>;
compatible = "regulator-fixed";
regulator-name = "usb_otg1_vbus";
gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
enable-active-high;
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
};
reg_usb_otg2_vbus: regulator-usb-otg2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_reg_usb2_en>;
compatible = "regulator-fixed";
regulator-name = "usb_otg2_vbus";
gpio = <&gpio1 8 GPIO_ACTIVE_HIGH>;
enable-active-high;
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
};
};
/* off-board header */
&ecspi2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi2>;
cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
status = "okay";
};
&gpio1 {
gpio-line-names = "rs485_term", "mipi_gpio4", "", "",
"", "", "pci_usb_sel", "dio0",
"", "dio1", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "";
};
&gpio4 {
gpio-line-names = "rs485_en", "mipi_gpio3", "rs485_hd", "mipi_gpio2",
"mipi_gpio1", "", "", "pci_wdis#",
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "";
};
&i2c2 {
clock-frequency = <400000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c2>;
status = "okay";
accelerometer@19 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_accel>;
compatible = "st,lis2de12";
reg = <0x19>;
st,drdy-int-pin = <1>;
interrupt-parent = <&gpio4>;
interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
interrupt-names = "INT1";
};
};
/* off-board header */
&i2c3 {
clock-frequency = <400000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3>;
status = "okay";
};
&pcie_phy {
fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
fsl,clkreq-unsupported;
clocks = <&pcie0_refclk>;
clock-names = "ref";
status = "okay";
};
&pcie0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pcie0>;
reset-gpio = <&gpio4 6 GPIO_ACTIVE_LOW>;
clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>,
<&pcie0_refclk>;
clock-names = "pcie", "pcie_aux", "pcie_bus";
assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
<&clk IMX8MM_CLK_PCIE1_CTRL>;
assigned-clock-rates = <10000000>, <250000000>;
assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
<&clk IMX8MM_SYS_PLL2_250M>;
status = "okay";
pcie@0,0 {
reg = <0x0000 0 0 0 0>;
#address-cells = <1>;
#size-cells = <0>;
pcie@1,0 {
reg = <0x0000 0 0 0 0>;
#address-cells = <1>;
#size-cells = <0>;
pcie@2,3 {
reg = <0x1800 0 0 0 0>;
#address-cells = <1>;
#size-cells = <0>;
eth1: pcie@5,0 {
reg = <0x0000 0 0 0 0>;
#address-cells = <1>;
#size-cells = <0>;
local-mac-address = [00 00 00 00 00 00];
};
};
};
};
};
/* off-board header */
&sai3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sai3>;
assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
assigned-clock-rates = <24576000>;
status = "okay";
};
/* GPS */
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
/* off-board header */
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
status = "okay";
};
/* RS232 */
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>;
status = "okay";
};
&usbotg1 {
dr_mode = "otg";
over-current-active-low;
vbus-supply = <&reg_usb_otg1_vbus>;
status = "okay";
};
&usbotg2 {
dr_mode = "host";
disable-over-current;
vbus-supply = <&reg_usb_otg2_vbus>;
status = "okay";
};
/* microSD */
&usdhc2 {
pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
bus-width = <4>;
vmmc-supply = <&reg_3p3v>;
status = "okay";
};
&iomuxc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hog>;
pinctrl_hog: hoggrp {
fsl,pins = <
MX8MM_IOMUXC_SPDIF_TX_GPIO5_IO3 0x40000041 /* PLUG_TEST */
MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x40000041 /* PCI_USBSEL */
MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7 0x40000041 /* PCIE_WDIS# */
MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x40000041 /* DIO0 */
MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x40000041 /* DIO1 */
MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x40000104 /* RS485_TERM */
MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0 0x40000104 /* RS485 */
MX8MM_IOMUXC_SAI1_RXD0_GPIO4_IO2 0x40000104 /* RS485_HALF */
>;
};
pinctrl_accel: accelgrp {
fsl,pins = <
MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5 0x159
>;
};
pinctrl_gpio_leds: gpioledgrp {
fsl,pins = <
MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x19
MX8MM_IOMUXC_SPDIF_RX_GPIO5_IO4 0x19
>;
};
pinctrl_i2c3: i2c3grp {
fsl,pins = <
MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3
MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3
>;
};
pinctrl_pcie0: pcie0grp {
fsl,pins = <
MX8MM_IOMUXC_SAI1_RXD4_GPIO4_IO6 0x41
>;
};
pinctrl_pps: ppsgrp {
fsl,pins = <
MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x41
>;
};
pinctrl_reg_usb1_en: regusb1grp {
fsl,pins = <
MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x41
MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x41
>;
};
pinctrl_reg_usb2_en: regusb2grp {
fsl,pins = <
MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x41
>;
};
pinctrl_sai3: sai3grp {
fsl,pins = <
MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6
MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6
MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK 0xd6
MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6
MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0xd6
>;
};
pinctrl_spi2: spi2grp {
fsl,pins = <
MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6
MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0xd6
MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0xd6
MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0xd6
>;
};
pinctrl_uart1: uart1grp {
fsl,pins = <
MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140
MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140
>;
};
pinctrl_uart3: uart3grp {
fsl,pins = <
MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140
MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140
>;
};
pinctrl_uart4: uart4grp {
fsl,pins = <
MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x140
MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x140
>;
};
pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190
MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0
MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0
MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0
MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0
MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0
>;
};
pinctrl_usdhc2: usdhc2grp {
fsl,pins = <
MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
>;
};
pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
fsl,pins = <
MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
>;
};
pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
fsl,pins = <
MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
>;
};
pinctrl_usdhc2_gpio: usdhc2gpiogrp {
fsl,pins = <
MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x1c4
MX8MM_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0x1d0
MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
>;
};
};