|  | // SPDX-License-Identifier: GPL-2.0+ | 
|  | // | 
|  | // max14577.c - mfd core driver for the Maxim 14577/77836 | 
|  | // | 
|  | // Copyright (C) 2014 Samsung Electronics | 
|  | // Chanwoo Choi <cw00.choi@samsung.com> | 
|  | // Krzysztof Kozlowski <krzk@kernel.org> | 
|  | // | 
|  | // This driver is based on max8997.c | 
|  |  | 
|  | #include <linux/err.h> | 
|  | #include <linux/module.h> | 
|  | #include <linux/interrupt.h> | 
|  | #include <linux/of_device.h> | 
|  | #include <linux/mfd/core.h> | 
|  | #include <linux/mfd/max14577.h> | 
|  | #include <linux/mfd/max14577-private.h> | 
|  |  | 
|  | /* | 
|  | * Table of valid charger currents for different Maxim chipsets. | 
|  | * It is placed here because it is used by both charger and regulator driver. | 
|  | */ | 
|  | const struct maxim_charger_current maxim_charger_currents[] = { | 
|  | [MAXIM_DEVICE_TYPE_UNKNOWN] = { 0, 0, 0, 0 }, | 
|  | [MAXIM_DEVICE_TYPE_MAX14577] = { | 
|  | .min		= MAX14577_CHARGER_CURRENT_LIMIT_MIN, | 
|  | .high_start	= MAX14577_CHARGER_CURRENT_LIMIT_HIGH_START, | 
|  | .high_step	= MAX14577_CHARGER_CURRENT_LIMIT_HIGH_STEP, | 
|  | .max		= MAX14577_CHARGER_CURRENT_LIMIT_MAX, | 
|  | }, | 
|  | [MAXIM_DEVICE_TYPE_MAX77836] = { | 
|  | .min		= MAX77836_CHARGER_CURRENT_LIMIT_MIN, | 
|  | .high_start	= MAX77836_CHARGER_CURRENT_LIMIT_HIGH_START, | 
|  | .high_step	= MAX77836_CHARGER_CURRENT_LIMIT_HIGH_STEP, | 
|  | .max		= MAX77836_CHARGER_CURRENT_LIMIT_MAX, | 
|  | }, | 
|  | }; | 
|  | EXPORT_SYMBOL_GPL(maxim_charger_currents); | 
|  |  | 
|  | /* | 
|  | * maxim_charger_calc_reg_current - Calculate register value for current | 
|  | * @limits:	constraints for charger, matching the MBCICHWRC register | 
|  | * @min_ua:	minimal requested current, micro Amps | 
|  | * @max_ua:	maximum requested current, micro Amps | 
|  | * @dst:	destination to store calculated register value | 
|  | * | 
|  | * Calculates the value of MBCICHWRC (Fast Battery Charge Current) register | 
|  | * for given current and stores it under pointed 'dst'. The stored value | 
|  | * combines low bit (MBCICHWRCL) and high bits (MBCICHWRCH). It is also | 
|  | * properly shifted. | 
|  | * | 
|  | * The calculated register value matches the current which: | 
|  | *  - is always between <limits.min, limits.max>; | 
|  | *  - is always less or equal to max_ua; | 
|  | *  - is the highest possible value; | 
|  | *  - may be lower than min_ua. | 
|  | * | 
|  | * On success returns 0. On error returns -EINVAL (requested min/max current | 
|  | * is outside of given charger limits) and 'dst' is not set. | 
|  | */ | 
|  | int maxim_charger_calc_reg_current(const struct maxim_charger_current *limits, | 
|  | unsigned int min_ua, unsigned int max_ua, u8 *dst) | 
|  | { | 
|  | unsigned int current_bits; | 
|  |  | 
|  | if (min_ua > max_ua) | 
|  | return -EINVAL; | 
|  |  | 
|  | if (min_ua > limits->max || max_ua < limits->min) | 
|  | return -EINVAL; | 
|  |  | 
|  | if (max_ua < limits->high_start) { | 
|  | /* | 
|  | * Less than high_start, so set the minimal current | 
|  | * (turn Low Bit off, 0 as high bits). | 
|  | */ | 
|  | *dst = 0x0; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | /* max_ua is in range: <high_start, infinite>, cut it to limits.max */ | 
|  | max_ua = min(limits->max, max_ua); | 
|  | max_ua -= limits->high_start; | 
|  | /* | 
|  | * There is no risk of overflow 'max_ua' here because: | 
|  | *  - max_ua >= limits.high_start | 
|  | *  - BUILD_BUG checks that 'limits' are: max >= high_start + high_step | 
|  | */ | 
|  | current_bits = max_ua / limits->high_step; | 
|  |  | 
|  | /* Turn Low Bit on (use range <limits.high_start, limits.max>) ... */ | 
|  | *dst = 0x1 << CHGCTRL4_MBCICHWRCL_SHIFT; | 
|  | /* and set proper High Bits */ | 
|  | *dst |= current_bits << CHGCTRL4_MBCICHWRCH_SHIFT; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  | EXPORT_SYMBOL_GPL(maxim_charger_calc_reg_current); | 
|  |  | 
|  | static const struct mfd_cell max14577_devs[] = { | 
|  | { | 
|  | .name = "max14577-muic", | 
|  | .of_compatible = "maxim,max14577-muic", | 
|  | }, | 
|  | { | 
|  | .name = "max14577-regulator", | 
|  | .of_compatible = "maxim,max14577-regulator", | 
|  | }, | 
|  | { | 
|  | .name = "max14577-charger", | 
|  | .of_compatible = "maxim,max14577-charger", | 
|  | }, | 
|  | }; | 
|  |  | 
|  | static const struct mfd_cell max77836_devs[] = { | 
|  | { | 
|  | .name = "max77836-muic", | 
|  | .of_compatible = "maxim,max77836-muic", | 
|  | }, | 
|  | { | 
|  | .name = "max77836-regulator", | 
|  | .of_compatible = "maxim,max77836-regulator", | 
|  | }, | 
|  | { | 
|  | .name = "max77836-charger", | 
|  | .of_compatible = "maxim,max77836-charger", | 
|  | }, | 
|  | { | 
|  | .name = "max77836-battery", | 
|  | .of_compatible = "maxim,max77836-battery", | 
|  | }, | 
|  | }; | 
|  |  | 
|  | static const struct of_device_id max14577_dt_match[] = { | 
|  | { | 
|  | .compatible = "maxim,max14577", | 
|  | .data = (void *)MAXIM_DEVICE_TYPE_MAX14577, | 
|  | }, | 
|  | { | 
|  | .compatible = "maxim,max77836", | 
|  | .data = (void *)MAXIM_DEVICE_TYPE_MAX77836, | 
|  | }, | 
|  | {}, | 
|  | }; | 
|  |  | 
|  | static bool max14577_muic_volatile_reg(struct device *dev, unsigned int reg) | 
|  | { | 
|  | switch (reg) { | 
|  | case MAX14577_REG_INT1 ... MAX14577_REG_STATUS3: | 
|  | return true; | 
|  | default: | 
|  | break; | 
|  | } | 
|  | return false; | 
|  | } | 
|  |  | 
|  | static bool max77836_muic_volatile_reg(struct device *dev, unsigned int reg) | 
|  | { | 
|  | /* Any max14577 volatile registers are also max77836 volatile. */ | 
|  | if (max14577_muic_volatile_reg(dev, reg)) | 
|  | return true; | 
|  |  | 
|  | switch (reg) { | 
|  | case MAX77836_FG_REG_VCELL_MSB ... MAX77836_FG_REG_SOC_LSB: | 
|  | case MAX77836_FG_REG_CRATE_MSB ... MAX77836_FG_REG_CRATE_LSB: | 
|  | case MAX77836_FG_REG_STATUS_H ... MAX77836_FG_REG_STATUS_L: | 
|  | case MAX77836_PMIC_REG_INTSRC: | 
|  | case MAX77836_PMIC_REG_TOPSYS_INT: | 
|  | case MAX77836_PMIC_REG_TOPSYS_STAT: | 
|  | return true; | 
|  | default: | 
|  | break; | 
|  | } | 
|  | return false; | 
|  | } | 
|  |  | 
|  | static const struct regmap_config max14577_muic_regmap_config = { | 
|  | .reg_bits	= 8, | 
|  | .val_bits	= 8, | 
|  | .volatile_reg	= max14577_muic_volatile_reg, | 
|  | .max_register	= MAX14577_REG_END, | 
|  | }; | 
|  |  | 
|  | static const struct regmap_config max77836_pmic_regmap_config = { | 
|  | .reg_bits	= 8, | 
|  | .val_bits	= 8, | 
|  | .volatile_reg	= max77836_muic_volatile_reg, | 
|  | .max_register	= MAX77836_PMIC_REG_END, | 
|  | }; | 
|  |  | 
|  | static const struct regmap_irq max14577_irqs[] = { | 
|  | /* INT1 interrupts */ | 
|  | { .reg_offset = 0, .mask = MAX14577_INT1_ADC_MASK, }, | 
|  | { .reg_offset = 0, .mask = MAX14577_INT1_ADCLOW_MASK, }, | 
|  | { .reg_offset = 0, .mask = MAX14577_INT1_ADCERR_MASK, }, | 
|  | /* INT2 interrupts */ | 
|  | { .reg_offset = 1, .mask = MAX14577_INT2_CHGTYP_MASK, }, | 
|  | { .reg_offset = 1, .mask = MAX14577_INT2_CHGDETRUN_MASK, }, | 
|  | { .reg_offset = 1, .mask = MAX14577_INT2_DCDTMR_MASK, }, | 
|  | { .reg_offset = 1, .mask = MAX14577_INT2_DBCHG_MASK, }, | 
|  | { .reg_offset = 1, .mask = MAX14577_INT2_VBVOLT_MASK, }, | 
|  | /* INT3 interrupts */ | 
|  | { .reg_offset = 2, .mask = MAX14577_INT3_EOC_MASK, }, | 
|  | { .reg_offset = 2, .mask = MAX14577_INT3_CGMBC_MASK, }, | 
|  | { .reg_offset = 2, .mask = MAX14577_INT3_OVP_MASK, }, | 
|  | { .reg_offset = 2, .mask = MAX14577_INT3_MBCCHGERR_MASK, }, | 
|  | }; | 
|  |  | 
|  | static const struct regmap_irq_chip max14577_irq_chip = { | 
|  | .name			= "max14577", | 
|  | .status_base		= MAX14577_REG_INT1, | 
|  | .mask_base		= MAX14577_REG_INTMASK1, | 
|  | .mask_invert		= true, | 
|  | .num_regs		= 3, | 
|  | .irqs			= max14577_irqs, | 
|  | .num_irqs		= ARRAY_SIZE(max14577_irqs), | 
|  | }; | 
|  |  | 
|  | static const struct regmap_irq max77836_muic_irqs[] = { | 
|  | /* INT1 interrupts */ | 
|  | { .reg_offset = 0, .mask = MAX14577_INT1_ADC_MASK, }, | 
|  | { .reg_offset = 0, .mask = MAX14577_INT1_ADCLOW_MASK, }, | 
|  | { .reg_offset = 0, .mask = MAX14577_INT1_ADCERR_MASK, }, | 
|  | { .reg_offset = 0, .mask = MAX77836_INT1_ADC1K_MASK, }, | 
|  | /* INT2 interrupts */ | 
|  | { .reg_offset = 1, .mask = MAX14577_INT2_CHGTYP_MASK, }, | 
|  | { .reg_offset = 1, .mask = MAX14577_INT2_CHGDETRUN_MASK, }, | 
|  | { .reg_offset = 1, .mask = MAX14577_INT2_DCDTMR_MASK, }, | 
|  | { .reg_offset = 1, .mask = MAX14577_INT2_DBCHG_MASK, }, | 
|  | { .reg_offset = 1, .mask = MAX14577_INT2_VBVOLT_MASK, }, | 
|  | { .reg_offset = 1, .mask = MAX77836_INT2_VIDRM_MASK, }, | 
|  | /* INT3 interrupts */ | 
|  | { .reg_offset = 2, .mask = MAX14577_INT3_EOC_MASK, }, | 
|  | { .reg_offset = 2, .mask = MAX14577_INT3_CGMBC_MASK, }, | 
|  | { .reg_offset = 2, .mask = MAX14577_INT3_OVP_MASK, }, | 
|  | { .reg_offset = 2, .mask = MAX14577_INT3_MBCCHGERR_MASK, }, | 
|  | }; | 
|  |  | 
|  | static const struct regmap_irq_chip max77836_muic_irq_chip = { | 
|  | .name			= "max77836-muic", | 
|  | .status_base		= MAX14577_REG_INT1, | 
|  | .mask_base		= MAX14577_REG_INTMASK1, | 
|  | .mask_invert		= true, | 
|  | .num_regs		= 3, | 
|  | .irqs			= max77836_muic_irqs, | 
|  | .num_irqs		= ARRAY_SIZE(max77836_muic_irqs), | 
|  | }; | 
|  |  | 
|  | static const struct regmap_irq max77836_pmic_irqs[] = { | 
|  | { .reg_offset = 0, .mask = MAX77836_TOPSYS_INT_T120C_MASK, }, | 
|  | { .reg_offset = 0, .mask = MAX77836_TOPSYS_INT_T140C_MASK, }, | 
|  | }; | 
|  |  | 
|  | static const struct regmap_irq_chip max77836_pmic_irq_chip = { | 
|  | .name			= "max77836-pmic", | 
|  | .status_base		= MAX77836_PMIC_REG_TOPSYS_INT, | 
|  | .mask_base		= MAX77836_PMIC_REG_TOPSYS_INT_MASK, | 
|  | .mask_invert		= false, | 
|  | .num_regs		= 1, | 
|  | .irqs			= max77836_pmic_irqs, | 
|  | .num_irqs		= ARRAY_SIZE(max77836_pmic_irqs), | 
|  | }; | 
|  |  | 
|  | static void max14577_print_dev_type(struct max14577 *max14577) | 
|  | { | 
|  | u8 reg_data, vendor_id, device_id; | 
|  | int ret; | 
|  |  | 
|  | ret = max14577_read_reg(max14577->regmap, MAX14577_REG_DEVICEID, | 
|  | ®_data); | 
|  | if (ret) { | 
|  | dev_err(max14577->dev, | 
|  | "Failed to read DEVICEID register: %d\n", ret); | 
|  | return; | 
|  | } | 
|  |  | 
|  | vendor_id = ((reg_data & DEVID_VENDORID_MASK) >> | 
|  | DEVID_VENDORID_SHIFT); | 
|  | device_id = ((reg_data & DEVID_DEVICEID_MASK) >> | 
|  | DEVID_DEVICEID_SHIFT); | 
|  |  | 
|  | dev_info(max14577->dev, "Device type: %u (ID: 0x%x, vendor: 0x%x)\n", | 
|  | max14577->dev_type, device_id, vendor_id); | 
|  | } | 
|  |  | 
|  | /* | 
|  | * Max77836 specific initialization code for driver probe. | 
|  | * Adds new I2C dummy device, regmap and regmap IRQ chip. | 
|  | * Unmasks Interrupt Source register. | 
|  | * | 
|  | * On success returns 0. | 
|  | * On failure returns errno and reverts any changes done so far (e.g. remove | 
|  | * I2C dummy device), except masking the INT SRC register. | 
|  | */ | 
|  | static int max77836_init(struct max14577 *max14577) | 
|  | { | 
|  | int ret; | 
|  | u8 intsrc_mask; | 
|  |  | 
|  | max14577->i2c_pmic = i2c_new_dummy_device(max14577->i2c->adapter, | 
|  | I2C_ADDR_PMIC); | 
|  | if (IS_ERR(max14577->i2c_pmic)) { | 
|  | dev_err(max14577->dev, "Failed to register PMIC I2C device\n"); | 
|  | return PTR_ERR(max14577->i2c_pmic); | 
|  | } | 
|  | i2c_set_clientdata(max14577->i2c_pmic, max14577); | 
|  |  | 
|  | max14577->regmap_pmic = devm_regmap_init_i2c(max14577->i2c_pmic, | 
|  | &max77836_pmic_regmap_config); | 
|  | if (IS_ERR(max14577->regmap_pmic)) { | 
|  | ret = PTR_ERR(max14577->regmap_pmic); | 
|  | dev_err(max14577->dev, "Failed to allocate PMIC register map: %d\n", | 
|  | ret); | 
|  | goto err; | 
|  | } | 
|  |  | 
|  | /* Un-mask MAX77836 Interrupt Source register */ | 
|  | ret = max14577_read_reg(max14577->regmap_pmic, | 
|  | MAX77836_PMIC_REG_INTSRC_MASK, &intsrc_mask); | 
|  | if (ret < 0) { | 
|  | dev_err(max14577->dev, "Failed to read PMIC register\n"); | 
|  | goto err; | 
|  | } | 
|  |  | 
|  | intsrc_mask &= ~(MAX77836_INTSRC_MASK_TOP_INT_MASK); | 
|  | intsrc_mask &= ~(MAX77836_INTSRC_MASK_MUIC_CHG_INT_MASK); | 
|  | ret = max14577_write_reg(max14577->regmap_pmic, | 
|  | MAX77836_PMIC_REG_INTSRC_MASK, intsrc_mask); | 
|  | if (ret < 0) { | 
|  | dev_err(max14577->dev, "Failed to write PMIC register\n"); | 
|  | goto err; | 
|  | } | 
|  |  | 
|  | ret = regmap_add_irq_chip(max14577->regmap_pmic, max14577->irq, | 
|  | IRQF_TRIGGER_FALLING | IRQF_ONESHOT | IRQF_SHARED, | 
|  | 0, &max77836_pmic_irq_chip, | 
|  | &max14577->irq_data_pmic); | 
|  | if (ret != 0) { | 
|  | dev_err(max14577->dev, "Failed to request PMIC IRQ %d: %d\n", | 
|  | max14577->irq, ret); | 
|  | goto err; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  |  | 
|  | err: | 
|  | i2c_unregister_device(max14577->i2c_pmic); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | /* | 
|  | * Max77836 specific de-initialization code for driver remove. | 
|  | */ | 
|  | static void max77836_remove(struct max14577 *max14577) | 
|  | { | 
|  | regmap_del_irq_chip(max14577->irq, max14577->irq_data_pmic); | 
|  | i2c_unregister_device(max14577->i2c_pmic); | 
|  | } | 
|  |  | 
|  | static int max14577_i2c_probe(struct i2c_client *i2c, | 
|  | const struct i2c_device_id *id) | 
|  | { | 
|  | struct max14577 *max14577; | 
|  | struct max14577_platform_data *pdata = dev_get_platdata(&i2c->dev); | 
|  | struct device_node *np = i2c->dev.of_node; | 
|  | int ret = 0; | 
|  | const struct regmap_irq_chip *irq_chip; | 
|  | const struct mfd_cell *mfd_devs; | 
|  | unsigned int mfd_devs_size; | 
|  | int irq_flags; | 
|  |  | 
|  | if (np) { | 
|  | pdata = devm_kzalloc(&i2c->dev, sizeof(*pdata), GFP_KERNEL); | 
|  | if (!pdata) | 
|  | return -ENOMEM; | 
|  | i2c->dev.platform_data = pdata; | 
|  | } | 
|  |  | 
|  | if (!pdata) { | 
|  | dev_err(&i2c->dev, "No platform data found.\n"); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | max14577 = devm_kzalloc(&i2c->dev, sizeof(*max14577), GFP_KERNEL); | 
|  | if (!max14577) | 
|  | return -ENOMEM; | 
|  |  | 
|  | i2c_set_clientdata(i2c, max14577); | 
|  | max14577->dev = &i2c->dev; | 
|  | max14577->i2c = i2c; | 
|  | max14577->irq = i2c->irq; | 
|  |  | 
|  | max14577->regmap = devm_regmap_init_i2c(i2c, | 
|  | &max14577_muic_regmap_config); | 
|  | if (IS_ERR(max14577->regmap)) { | 
|  | ret = PTR_ERR(max14577->regmap); | 
|  | dev_err(max14577->dev, "Failed to allocate register map: %d\n", | 
|  | ret); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | if (np) { | 
|  | const struct of_device_id *of_id; | 
|  |  | 
|  | of_id = of_match_device(max14577_dt_match, &i2c->dev); | 
|  | if (of_id) | 
|  | max14577->dev_type = | 
|  | (enum maxim_device_type)of_id->data; | 
|  | } else { | 
|  | max14577->dev_type = id->driver_data; | 
|  | } | 
|  |  | 
|  | max14577_print_dev_type(max14577); | 
|  |  | 
|  | switch (max14577->dev_type) { | 
|  | case MAXIM_DEVICE_TYPE_MAX77836: | 
|  | irq_chip = &max77836_muic_irq_chip; | 
|  | mfd_devs = max77836_devs; | 
|  | mfd_devs_size = ARRAY_SIZE(max77836_devs); | 
|  | irq_flags = IRQF_TRIGGER_FALLING | IRQF_ONESHOT | IRQF_SHARED; | 
|  | break; | 
|  | case MAXIM_DEVICE_TYPE_MAX14577: | 
|  | default: | 
|  | irq_chip = &max14577_irq_chip; | 
|  | mfd_devs = max14577_devs; | 
|  | mfd_devs_size = ARRAY_SIZE(max14577_devs); | 
|  | irq_flags = IRQF_TRIGGER_FALLING | IRQF_ONESHOT; | 
|  | break; | 
|  | } | 
|  |  | 
|  | ret = regmap_add_irq_chip(max14577->regmap, max14577->irq, | 
|  | irq_flags, 0, irq_chip, | 
|  | &max14577->irq_data); | 
|  | if (ret != 0) { | 
|  | dev_err(&i2c->dev, "Failed to request IRQ %d: %d\n", | 
|  | max14577->irq, ret); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | /* Max77836 specific initialization code (additional regmap) */ | 
|  | if (max14577->dev_type == MAXIM_DEVICE_TYPE_MAX77836) { | 
|  | ret = max77836_init(max14577); | 
|  | if (ret < 0) | 
|  | goto err_max77836; | 
|  | } | 
|  |  | 
|  | ret = mfd_add_devices(max14577->dev, -1, mfd_devs, | 
|  | mfd_devs_size, NULL, 0, NULL); | 
|  | if (ret < 0) | 
|  | goto err_mfd; | 
|  |  | 
|  | device_init_wakeup(max14577->dev, 1); | 
|  |  | 
|  | return 0; | 
|  |  | 
|  | err_mfd: | 
|  | if (max14577->dev_type == MAXIM_DEVICE_TYPE_MAX77836) | 
|  | max77836_remove(max14577); | 
|  | err_max77836: | 
|  | regmap_del_irq_chip(max14577->irq, max14577->irq_data); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int max14577_i2c_remove(struct i2c_client *i2c) | 
|  | { | 
|  | struct max14577 *max14577 = i2c_get_clientdata(i2c); | 
|  |  | 
|  | mfd_remove_devices(max14577->dev); | 
|  | regmap_del_irq_chip(max14577->irq, max14577->irq_data); | 
|  | if (max14577->dev_type == MAXIM_DEVICE_TYPE_MAX77836) | 
|  | max77836_remove(max14577); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static const struct i2c_device_id max14577_i2c_id[] = { | 
|  | { "max14577", MAXIM_DEVICE_TYPE_MAX14577, }, | 
|  | { "max77836", MAXIM_DEVICE_TYPE_MAX77836, }, | 
|  | { } | 
|  | }; | 
|  | MODULE_DEVICE_TABLE(i2c, max14577_i2c_id); | 
|  |  | 
|  | #ifdef CONFIG_PM_SLEEP | 
|  | static int max14577_suspend(struct device *dev) | 
|  | { | 
|  | struct i2c_client *i2c = to_i2c_client(dev); | 
|  | struct max14577 *max14577 = i2c_get_clientdata(i2c); | 
|  |  | 
|  | if (device_may_wakeup(dev)) | 
|  | enable_irq_wake(max14577->irq); | 
|  | /* | 
|  | * MUIC IRQ must be disabled during suspend because if it happens | 
|  | * while suspended it will be handled before resuming I2C. | 
|  | * | 
|  | * When device is woken up from suspend (e.g. by ADC change), | 
|  | * an interrupt occurs before resuming I2C bus controller. | 
|  | * Interrupt handler tries to read registers but this read | 
|  | * will fail because I2C is still suspended. | 
|  | */ | 
|  | disable_irq(max14577->irq); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int max14577_resume(struct device *dev) | 
|  | { | 
|  | struct i2c_client *i2c = to_i2c_client(dev); | 
|  | struct max14577 *max14577 = i2c_get_clientdata(i2c); | 
|  |  | 
|  | if (device_may_wakeup(dev)) | 
|  | disable_irq_wake(max14577->irq); | 
|  | enable_irq(max14577->irq); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  | #endif /* CONFIG_PM_SLEEP */ | 
|  |  | 
|  | static SIMPLE_DEV_PM_OPS(max14577_pm, max14577_suspend, max14577_resume); | 
|  |  | 
|  | static struct i2c_driver max14577_i2c_driver = { | 
|  | .driver = { | 
|  | .name = "max14577", | 
|  | .pm = &max14577_pm, | 
|  | .of_match_table = max14577_dt_match, | 
|  | }, | 
|  | .probe = max14577_i2c_probe, | 
|  | .remove = max14577_i2c_remove, | 
|  | .id_table = max14577_i2c_id, | 
|  | }; | 
|  |  | 
|  | static int __init max14577_i2c_init(void) | 
|  | { | 
|  | BUILD_BUG_ON(ARRAY_SIZE(max14577_i2c_id) != MAXIM_DEVICE_TYPE_NUM); | 
|  | BUILD_BUG_ON(ARRAY_SIZE(max14577_dt_match) != MAXIM_DEVICE_TYPE_NUM); | 
|  |  | 
|  | /* Valid charger current values must be provided for each chipset */ | 
|  | BUILD_BUG_ON(ARRAY_SIZE(maxim_charger_currents) != MAXIM_DEVICE_TYPE_NUM); | 
|  |  | 
|  | /* Check for valid values for charger */ | 
|  | BUILD_BUG_ON(MAX14577_CHARGER_CURRENT_LIMIT_HIGH_START + | 
|  | MAX14577_CHARGER_CURRENT_LIMIT_HIGH_STEP * 0xf != | 
|  | MAX14577_CHARGER_CURRENT_LIMIT_MAX); | 
|  | BUILD_BUG_ON(MAX14577_CHARGER_CURRENT_LIMIT_HIGH_STEP == 0); | 
|  |  | 
|  | BUILD_BUG_ON(MAX77836_CHARGER_CURRENT_LIMIT_HIGH_START + | 
|  | MAX77836_CHARGER_CURRENT_LIMIT_HIGH_STEP * 0xf != | 
|  | MAX77836_CHARGER_CURRENT_LIMIT_MAX); | 
|  | BUILD_BUG_ON(MAX77836_CHARGER_CURRENT_LIMIT_HIGH_STEP == 0); | 
|  |  | 
|  | return i2c_add_driver(&max14577_i2c_driver); | 
|  | } | 
|  | module_init(max14577_i2c_init); | 
|  |  | 
|  | static void __exit max14577_i2c_exit(void) | 
|  | { | 
|  | i2c_del_driver(&max14577_i2c_driver); | 
|  | } | 
|  | module_exit(max14577_i2c_exit); | 
|  |  | 
|  | MODULE_AUTHOR("Chanwoo Choi <cw00.choi@samsung.com>, Krzysztof Kozlowski <krzk@kernel.org>"); | 
|  | MODULE_DESCRIPTION("Maxim 14577/77836 multi-function core driver"); | 
|  | MODULE_LICENSE("GPL"); |