blob: f5f3df3ad692b64e307923e67ba951c7e1db54cb [file] [log] [blame]
/*
* Config file for Compulab CM-FX6 board
*
* Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/
*
* Author: Nikita Kiryanov <nikita@compulab.co.il>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_CM_FX6_H
#define __CONFIG_CM_FX6_H
#include "mx6_common.h"
/* Machine config */
#define CONFIG_SYS_LITTLE_ENDIAN
#define CONFIG_MACH_TYPE 4273
/* CMD */
#define CONFIG_CMD_MTDPARTS
/* MMC */
#define CONFIG_SYS_FSL_USDHC_NUM 3
#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR
/* RAM */
#define PHYS_SDRAM_1 MMDC0_ARB_BASE_ADDR
#define PHYS_SDRAM_2 MMDC1_ARB_BASE_ADDR
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_NR_DRAM_BANKS 2
#define CONFIG_SYS_MEMTEST_START 0x10000000
#define CONFIG_SYS_MEMTEST_END 0x10010000
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
/* Serial console */
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE UART4_BASE
#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
/* Shell */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
/* SPI flash */
#define CONFIG_SF_DEFAULT_BUS 0
#define CONFIG_SF_DEFAULT_CS 0
#define CONFIG_SF_DEFAULT_SPEED 25000000
#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
/* MTD support */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define CONFIG_SPI_FLASH_MTD
#endif
#define MTDIDS_DEFAULT "nor0=spi0.0"
#define MTDPARTS_DEFAULT "mtdparts=spi0.0:" \
"768k(uboot)," \
"256k(uboot-environment)," \
"-(reserved)"
/* Environment */
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
#define CONFIG_ENV_SECT_SIZE (64 * 1024)
#define CONFIG_ENV_SIZE (8 * 1024)
#define CONFIG_ENV_OFFSET (768 * 1024)
#define CONFIG_EXTRA_ENV_SETTINGS \
"stdin=serial,usbkbd\0" \
"stdout=serial,vga\0" \
"stderr=serial,vga\0" \
"panel=HDMI\0" \
"autoload=no\0" \
"uImage=uImage-cm-fx6\0" \
"zImage=zImage-cm-fx6\0" \
"kernel=uImage-cm-fx6\0" \
"script=boot.scr\0" \
"dtb=cm-fx6.dtb\0" \
"bootm_low=18000000\0" \
"loadaddr=0x10800000\0" \
"fdtaddr=0x11000000\0" \
"console=ttymxc3,115200\0" \
"ethprime=FEC0\0" \
"video_hdmi=mxcfb0:dev=hdmi,1920x1080M-32@50,if=RGB32\0" \
"video_dvi=mxcfb0:dev=dvi,1280x800M-32@50,if=RGB32\0" \
"doboot=bootm ${loadaddr}\0" \
"doloadfdt=false\0" \
"mtdids=" MTDIDS_DEFAULT "\0" \
"mtdparts=" MTDPARTS_DEFAULT "\0" \
"setboottypez=setenv kernel ${zImage};" \
"setenv doboot bootz ${loadaddr} - ${fdtaddr};" \
"setenv doloadfdt true;\0" \
"setboottypem=setenv kernel ${uImage};" \
"setenv doboot bootm ${loadaddr};" \
"setenv doloadfdt false;\0"\
"mmcroot=/dev/mmcblk0p2 rw rootwait\0" \
"sataroot=/dev/sda2 rw rootwait\0" \
"nandroot=/dev/mtdblock4 rw\0" \
"nandrootfstype=ubifs\0" \
"mmcargs=setenv bootargs console=${console} root=${mmcroot} " \
"${video} ${extrabootargs}\0" \
"sataargs=setenv bootargs console=${console} root=${sataroot} " \
"${video} ${extrabootargs}\0" \
"nandargs=setenv bootargs console=${console} " \
"root=${nandroot} " \
"rootfstype=${nandrootfstype} " \
"${video} ${extrabootargs}\0" \
"nandboot=if run nandloadkernel; then " \
"run nandloadfdt;" \
"run setboottypem;" \
"run storagebootcmd;" \
"run setboottypez;" \
"run storagebootcmd;" \
"fi;\0" \
"run_eboot=echo Starting EBOOT ...; "\
"mmc dev 2 && " \
"mmc rescan && mmc read 10042000 a 400 && go 10042000\0" \
"loadscript=load ${storagetype} ${storagedev} ${loadaddr} ${script};\0"\
"loadkernel=load ${storagetype} ${storagedev} ${loadaddr} ${kernel};\0"\
"loadfdt=load ${storagetype} ${storagedev} ${fdtaddr} ${dtb};\0" \
"bootscript=echo Running bootscript from ${storagetype} ...;" \
"source ${loadaddr};\0" \
"nandloadkernel=nand read ${loadaddr} 0 780000;\0" \
"nandloadfdt=nand read ${fdtaddr} 780000 80000;\0" \
"setupmmcboot=setenv storagetype mmc; setenv storagedev 2;\0" \
"setupsataboot=setenv storagetype sata; setenv storagedev 0;\0" \
"setupnandboot=setenv storagetype nand;\0" \
"setupusbboot=setenv storagetype usb; setenv storagedev 0;\0" \
"storagebootcmd=echo Booting from ${storagetype} ...;" \
"run ${storagetype}args; run doboot;\0" \
"trybootk=if run loadkernel; then " \
"if ${doloadfdt}; then " \
"run loadfdt;" \
"fi;" \
"run storagebootcmd;" \
"fi;\0" \
"trybootsmz=if run loadscript; then " \
"run bootscript;" \
"fi;" \
"run setboottypem;" \
"run trybootk;" \
"run setboottypez;" \
"run trybootk;\0"
#define CONFIG_BOOTCOMMAND \
"run setupmmcboot;" \
"mmc dev ${storagedev};" \
"if mmc rescan; then " \
"run trybootsmz;" \
"fi;" \
"run setupusbboot;" \
"if usb start; then "\
"if run loadscript; then " \
"run bootscript;" \
"fi;" \
"fi;" \
"run setupsataboot;" \
"if sata init; then " \
"run trybootsmz;" \
"fi;" \
"run setupnandboot;" \
"run nandboot;"
#define CONFIG_PREBOOT "usb start;sf probe"
/* SPI */
#define CONFIG_SPI
#define CONFIG_MXC_SPI
/* NAND */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BASE 0x40000000
#define CONFIG_SYS_NAND_MAX_CHIPS 1
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_NAND_MXS
#define CONFIG_SYS_NAND_ONFI_DETECTION
/* APBH DMA is required for NAND support */
#define CONFIG_APBH_DMA
#define CONFIG_APBH_DMA_BURST
#define CONFIG_APBH_DMA_BURST8
#endif
/* Ethernet */
#define CONFIG_FEC_MXC
#define CONFIG_FEC_MXC_PHYADDR 0
#define CONFIG_FEC_XCV_TYPE RGMII
#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_PHYLIB
#define CONFIG_PHY_ATHEROS
#define CONFIG_MII
#define CONFIG_ETHPRIME "FEC0"
#define CONFIG_ARP_TIMEOUT 200UL
#define CONFIG_NET_RETRY_COUNT 5
/* USB */
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_MXC_I2C3_SPEED 400000
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_I2C_EEPROM_BUS 2
/* SATA */
#define CONFIG_CMD_SATA
#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_LIBATA
#define CONFIG_LBA48
#define CONFIG_DWC_AHSATA
#define CONFIG_DWC_AHSATA_PORT_ID 0
#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
/* Boot */
#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
#define CONFIG_SERIAL_TAG
/* misc */
#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
#define CONFIG_MISC_INIT_R
/* SPL */
#include "imx6_spl.h"
#define CONFIG_SYS_SPI_U_BOOT_OFFS (64 * 1024)
#define CONFIG_SPL_SPI_LOAD
/* Display */
#define CONFIG_VIDEO_IPUV3
#define CONFIG_IPUV3_CLK 260000000
#define CONFIG_IMX_HDMI
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SOURCE
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
/* EEPROM */
#define CONFIG_CMD_EEPROM
#define CONFIG_ENV_EEPROM_IS_ON_I2C
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
#define CONFIG_SYS_EEPROM_SIZE 256
#define CONFIG_CMD_EEPROM_LAYOUT
#define CONFIG_EEPROM_LAYOUT_HELP_STRING "v2, v3"
#endif /* __CONFIG_CM_FX6_H */