blob: a330372d19d064e82a1112591f7c8d132623cb32 [file] [log] [blame]
/*
* (C) Copyright 2008
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* SPDX-License-Identifier: GPL-2.0+
*/
/************************************************************************
* canyonlands.h - configuration for Canyonlands (460EX)
***********************************************************************/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <linux/kconfig.h>
/*-----------------------------------------------------------------------
* High Level Configuration Options
*----------------------------------------------------------------------*/
/*
* This config file is used for Canyonlands (460EX) Glacier (460GT)
* and Arches dual (460GT)
*/
#ifdef CONFIG_CANYONLANDS
#define CONFIG_460EX /* Specific PPC460EX */
#define CONFIG_HOSTNAME canyonlands
#else
#define CONFIG_460GT /* Specific PPC460GT */
#ifdef CONFIG_GLACIER
#define CONFIG_HOSTNAME glacier
#else
#define CONFIG_HOSTNAME arches
#define CONFIG_USE_NETDEV eth1
#define CONFIG_BD_NUM_CPUS 2
#endif
#endif
#define CONFIG_440
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0xFFF80000
#endif
/*
* Include common defines/options for all AMCC eval boards
*/
#include "amcc-common.h"
#define CONFIG_SYS_CLK_FREQ 66666667 /* external freq to pll */
#define CONFIG_BOARD_EARLY_INIT_R /* Call board_early_init_r */
#define CONFIG_MISC_INIT_R /* Call misc_init_r */
#define CONFIG_BOARD_TYPES /* support board types */
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped PCI memory */
#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */
#define CONFIG_SYS_PCI_TARGBASE CONFIG_SYS_PCI_MEMBASE
#define CONFIG_SYS_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */
#define CONFIG_SYS_PCIE_MEMSIZE 0x08000000 /* smallest incr for PCIe port */
#define CONFIG_SYS_PCIE_BASE 0xc4000000 /* PCIe UTL regs */
#define CONFIG_SYS_PCIE0_CFGBASE 0xc0000000
#define CONFIG_SYS_PCIE1_CFGBASE 0xc1000000
#define CONFIG_SYS_PCIE0_XCFGBASE 0xc3000000
#define CONFIG_SYS_PCIE1_XCFGBASE 0xc3001000
/*
* BCSR bits as defined in the Canyonlands board user manual.
*/
#define BCSR_USBCTRL_OTG_RST 0x32
#define BCSR_USBCTRL_HOST_RST 0x01
#define BCSR_SELECT_PCIE 0x10
#define CONFIG_SYS_PCIE0_UTLBASE 0xc08010000ULL /* 36bit physical addr */
/* base address of inbound PCIe window */
#define CONFIG_SYS_PCIE_INBOUND_BASE 0x000000000ULL /* 36bit physical addr */
/* EBC stuff */
#if !defined(CONFIG_ARCHES)
#define CONFIG_SYS_BCSR_BASE 0xE1000000
#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* later mapped to this addr */
#define CONFIG_SYS_FLASH_SIZE (64 << 20)
#else
#define CONFIG_SYS_FPGA_BASE 0xE1000000
#define CONFIG_SYS_CPLD_ADDR (CONFIG_SYS_FPGA_BASE + 0x00080000)
#define CONFIG_SYS_CPLD_DATA (CONFIG_SYS_FPGA_BASE + 0x00080002)
#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* later mapped to this addr */
#define CONFIG_SYS_FLASH_SIZE (32 << 20)
#endif
#define CONFIG_SYS_NAND_ADDR 0xE0000000
#define CONFIG_SYS_BOOT_BASE_ADDR 0xFF000000 /* EBC Boot Space: 0xFF000000 */
#define CONFIG_SYS_FLASH_BASE_PHYS_H 0x4
#define CONFIG_SYS_FLASH_BASE_PHYS_L 0xCC000000
#define CONFIG_SYS_FLASH_BASE_PHYS (((u64)CONFIG_SYS_FLASH_BASE_PHYS_H << 32) | \
(u64)CONFIG_SYS_FLASH_BASE_PHYS_L)
#define CONFIG_SYS_OCM_BASE 0xE3000000 /* OCM: 64k */
#define CONFIG_SYS_SRAM_BASE 0xE8000000 /* SRAM: 256k */
#define CONFIG_SYS_SRAM_SIZE (256 << 10)
#define CONFIG_SYS_LOCAL_CONF_REGS 0xEF000000
#define CONFIG_SYS_AHB_BASE 0xE2000000 /* internal AHB peripherals */
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in OCM)
*----------------------------------------------------------------------*/
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */
#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10)
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
#define CONFIG_CONS_INDEX 1 /* Use UART0 */
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
/*
* Define here the location of the environment variables (FLASH).
*/
#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
#define CONFIG_SYS_NOR_CS 0 /* NOR chip connected to CSx */
#define CONFIG_SYS_NAND_CS 3 /* NAND chip connected to CSx */
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CONFIG_SYS_FLASH_CFI_AMD_RESET /* Use AMD (Spansion) reset cmd */
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#ifdef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#endif /* CONFIG_ENV_IS_IN_FLASH */
/*-----------------------------------------------------------------------
* NAND-FLASH related
*----------------------------------------------------------------------*/
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS)
#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
/*------------------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------------*/
#if !defined(CONFIG_ARCHES)
/*
* NAND booting U-Boot version uses a fixed initialization, since the whole
* I2C SPD DIMM autodetection/calibration doesn't fit into the 4k of boot
* code.
*/
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
#define SPD_EEPROM_ADDRESS {0x50, 0x51} /* SPD i2c spd addresses*/
#define CONFIG_DDR_ECC /* with ECC support */
#define CONFIG_DDR_RQDC_FIXED 0x80000038 /* fixed value for RQDC */
#else /* defined(CONFIG_ARCHES) */
#define CONFIG_AUTOCALIB "silent\0" /* default is non-verbose */
#define CONFIG_PPC4xx_DDR_AUTOCALIBRATION /* IBM DDR autocalibration */
#define DEBUG_PPC4xx_DDR_AUTOCALIBRATION /* dynamic DDR autocal debug */
#undef CONFIG_PPC4xx_DDR_METHOD_A
/* DDR1/2 SDRAM Device Control Register Data Values */
/* Memory Queue */
#define CONFIG_SYS_SDRAM_R0BAS 0x0000f000
#define CONFIG_SYS_SDRAM_R1BAS 0x00000000
#define CONFIG_SYS_SDRAM_R2BAS 0x00000000
#define CONFIG_SYS_SDRAM_R3BAS 0x00000000
#define CONFIG_SYS_SDRAM_PLBADDULL 0x00000000
#define CONFIG_SYS_SDRAM_PLBADDUHB 0x00000008
#define CONFIG_SYS_SDRAM_CONF1LL 0x00001080
#define CONFIG_SYS_SDRAM_CONF1HB 0x00001080
#define CONFIG_SYS_SDRAM_CONFPATHB 0x10a68000
/* SDRAM Controller */
#define CONFIG_SYS_SDRAM0_MB0CF 0x00000701
#define CONFIG_SYS_SDRAM0_MB1CF 0x00000000
#define CONFIG_SYS_SDRAM0_MB2CF 0x00000000
#define CONFIG_SYS_SDRAM0_MB3CF 0x00000000
#define CONFIG_SYS_SDRAM0_MCOPT1 0x05322000
#define CONFIG_SYS_SDRAM0_MCOPT2 0x00000000
#define CONFIG_SYS_SDRAM0_MODT0 0x01000000
#define CONFIG_SYS_SDRAM0_MODT1 0x00000000
#define CONFIG_SYS_SDRAM0_MODT2 0x00000000
#define CONFIG_SYS_SDRAM0_MODT3 0x00000000
#define CONFIG_SYS_SDRAM0_CODT 0x00800021
#define CONFIG_SYS_SDRAM0_RTR 0x06180000
#define CONFIG_SYS_SDRAM0_INITPLR0 0xb5380000
#define CONFIG_SYS_SDRAM0_INITPLR1 0x82100400
#define CONFIG_SYS_SDRAM0_INITPLR2 0x80820000
#define CONFIG_SYS_SDRAM0_INITPLR3 0x80830000
#define CONFIG_SYS_SDRAM0_INITPLR4 0x80810040
#define CONFIG_SYS_SDRAM0_INITPLR5 0x80800532
#define CONFIG_SYS_SDRAM0_INITPLR6 0x82100400
#define CONFIG_SYS_SDRAM0_INITPLR7 0x8a080000
#define CONFIG_SYS_SDRAM0_INITPLR8 0x8a080000
#define CONFIG_SYS_SDRAM0_INITPLR9 0x8a080000
#define CONFIG_SYS_SDRAM0_INITPLR10 0x8a080000
#define CONFIG_SYS_SDRAM0_INITPLR11 0x80000432
#define CONFIG_SYS_SDRAM0_INITPLR12 0x808103c0
#define CONFIG_SYS_SDRAM0_INITPLR13 0x80810040
#define CONFIG_SYS_SDRAM0_INITPLR14 0x00000000
#define CONFIG_SYS_SDRAM0_INITPLR15 0x00000000
#define CONFIG_SYS_SDRAM0_RQDC 0x80000038
#define CONFIG_SYS_SDRAM0_RFDC 0x00000257
#define CONFIG_SYS_SDRAM0_RDCC 0x40000000
#define CONFIG_SYS_SDRAM0_DLCR 0x03000091
#define CONFIG_SYS_SDRAM0_CLKTR 0x40000000
#define CONFIG_SYS_SDRAM0_WRDTR 0x82000823
#define CONFIG_SYS_SDRAM0_SDTR1 0x80201000
#define CONFIG_SYS_SDRAM0_SDTR2 0x42204243
#define CONFIG_SYS_SDRAM0_SDTR3 0x090c0d1a
#define CONFIG_SYS_SDRAM0_MMODE 0x00000432
#define CONFIG_SYS_SDRAM0_MEMODE 0x00000004
#endif /* !defined(CONFIG_ARCHES) */
#define CONFIG_SYS_MBYTES_SDRAM 512 /* 512MB */
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1)
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
/* I2C bootstrap EEPROM */
#if defined(CONFIG_ARCHES)
#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x54
#else
#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x52
#endif
#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0
#define CONFIG_4xx_CONFIG_BLOCKSIZE 16
/* I2C SYSMON (LM75, AD7414 is almost compatible) */
#define CONFIG_DTT_LM75 /* ON Semi's LM75 */
#define CONFIG_DTT_AD7414 /* use AD7414 */
#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
#define CONFIG_SYS_DTT_MAX_TEMP 70
#define CONFIG_SYS_DTT_LOW_TEMP -30
#define CONFIG_SYS_DTT_HYSTERESIS 3
#if defined(CONFIG_ARCHES)
#define CONFIG_SYS_I2C_DTT_ADDR 0x4a /* AD7414 I2C address */
#endif
#if !defined(CONFIG_ARCHES)
/* RTC configuration */
#define CONFIG_RTC_M41T62
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#endif
/*-----------------------------------------------------------------------
* Ethernet
*----------------------------------------------------------------------*/
#define CONFIG_IBM_EMAC4_V4
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#if !defined(CONFIG_ARCHES)
#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
#define CONFIG_PHY1_ADDR 1
/* Only Glacier (460GT) has 4 EMAC interfaces */
#ifdef CONFIG_460GT
#define CONFIG_PHY2_ADDR 2
#define CONFIG_PHY3_ADDR 3
#define CONFIG_HAS_ETH2
#define CONFIG_HAS_ETH3
#endif
#else /* defined(CONFIG_ARCHES) */
#define CONFIG_FIXED_PHY 0xFFFFFFFF
#define CONFIG_PHY_ADDR CONFIG_FIXED_PHY
#define CONFIG_PHY1_ADDR 0
#define CONFIG_PHY2_ADDR 1
#define CONFIG_HAS_ETH2
#define CONFIG_SYS_FIXED_PHY_PORT(devnum, speed, duplex) \
{devnum, speed, duplex}
#define CONFIG_SYS_FIXED_PHY_PORTS \
CONFIG_SYS_FIXED_PHY_PORT(0, 1000, FULL)
#define CONFIG_M88E1112_PHY
/*
* For the GPCS_PHYx_ADDR PHY address, choose some PHY address not
* used by CONFIG_PHYx_ADDR
*/
#define CONFIG_GPCS_PHY_ADDR 0xA
#define CONFIG_GPCS_PHY1_ADDR 0xB
#define CONFIG_GPCS_PHY2_ADDR 0xC
#endif /* !defined(CONFIG_ARCHES) */
#define CONFIG_PHY_RESET /* reset phy upon startup */
#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
#define CONFIG_PHY_DYNAMIC_ANEG
/*-----------------------------------------------------------------------
* USB-OHCI
*----------------------------------------------------------------------*/
/* Only Canyonlands (460EX) has USB */
#ifdef CONFIG_460EX
#define CONFIG_USB_OHCI_NEW
#undef CONFIG_SYS_OHCI_BE_CONTROLLER /* 460EX has little endian descriptors */
#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS /* 460EX has little endian register */
#define CONFIG_SYS_OHCI_USE_NPS /* force NoPowerSwitching mode */
#define CONFIG_SYS_USB_OHCI_REGS_BASE (CONFIG_SYS_AHB_BASE | 0xd0000)
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
#define CONFIG_SYS_USB_OHCI_BOARD_INIT
#endif
/*
* Default environment variables
*/
#if !defined(CONFIG_ARCHES)
#define CONFIG_EXTRA_ENV_SETTINGS \
CONFIG_AMCC_DEF_ENV \
CONFIG_AMCC_DEF_ENV_POWERPC \
CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fc000000\0" \
"fdt_addr=fc1e0000\0" \
"ramdisk_addr=fc200000\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:RP\0" \
""
#else /* defined(CONFIG_ARCHES) */
#define CONFIG_EXTRA_ENV_SETTINGS \
CONFIG_AMCC_DEF_ENV \
CONFIG_AMCC_DEF_ENV_POWERPC \
CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fe000000\0" \
"fdt_addr=fe1e0000\0" \
"ramdisk_addr=fe200000\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:RP\0" \
"ethprime=ppc_4xx_eth1\0" \
""
#endif /* !defined(CONFIG_ARCHES) */
/*
* Commands additional to the ones defined in amcc-common.h
*/
#if defined(CONFIG_ARCHES)
#define CONFIG_CMD_DTT
#define CONFIG_CMD_PCI
#define CONFIG_CMD_SDRAM
#elif defined(CONFIG_CANYONLANDS)
#define CONFIG_CMD_DTT
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PCI
#define CONFIG_CMD_SATA
#define CONFIG_CMD_SDRAM
#elif defined(CONFIG_GLACIER)
#define CONFIG_CMD_DTT
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PCI
#define CONFIG_CMD_SDRAM
#else
#error "board type not defined"
#endif
/* Partitions */
/*-----------------------------------------------------------------------
* PCI stuff
*----------------------------------------------------------------------*/
/* General PCI */
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_PCI_CONFIG_HOST_BRIDGE
/* Board-specific PCI */
#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */
#undef CONFIG_SYS_PCI_MASTER_INIT
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
#ifdef CONFIG_460GT
#if defined(CONFIG_ARCHES)
/*-----------------------------------------------------------------------
* RapidIO I/O and Registers
*----------------------------------------------------------------------*/
#define CONFIG_RAPIDIO
#define CONFIG_SYS_460GT_SRIO_ERRATA_1
#define SRGPL0_REG_BAR 0x0000000DAA000000ull /* 16MB */
#define SRGPL0_CFG_BAR 0x0000000DAB000000ull /* 16MB */
#define SRGPL0_MNT_BAR 0x0000000DAC000000ull /* 16MB */
#define SRGPL0_MSG_BAR 0x0000000DAD000000ull /* 16MB */
#define SRGPL0_OUT_BAR 0x0000000DB0000000ull /* 256MB */
#define CONFIG_SYS_SRGPL0_REG_BAR 0xAA000000 /* 16MB */
#define CONFIG_SYS_SRGPL0_CFG_BAR 0xAB000000 /* 16MB */
#define CONFIG_SYS_SRGPL0_MNT_BAR 0xAC000000 /* 16MB */
#define CONFIG_SYS_SRGPL0_MSG_BAR 0xAD000000 /* 16MB */
#define CONFIG_SYS_I2ODMA_BASE 0xCF000000
#define CONFIG_SYS_I2ODMA_PHYS_ADDR 0x0000000400100000ull
#define CONFIG_PPC4XX_RAPIDIO_PROMISCUOUS_MODE
#undef CONFIG_PPC4XX_RAPIDIO_DEBUG
#undef CONFIG_PPC4XX_RAPIDIO_IN_BAR_USE_OCM
#define CONFIG_PPC4XX_RAPIDIO_USE_HB_PLB
#undef CONFIG_PPC4XX_RAPIDIO_LOOPBACK
#endif /* CONFIG_ARCHES */
#endif /* CONFIG_460GT */
/*
* SATA driver setup
*/
#ifdef CONFIG_CMD_SATA
#define CONFIG_SATA_DWC
#define CONFIG_LIBATA
#define SATA_BASE_ADDR 0xe20d1000 /* PPC460EX SATA Base Address */
#define SATA_DMA_REG_ADDR 0xe20d0800 /* PPC460EX SATA Base Address */
#define CONFIG_SYS_SATA_MAX_DEVICE 1 /* SATA MAX DEVICE */
/* Convert sectorsize to wordsize */
#define ATA_SECTOR_WORDS (ATA_SECT_SIZE/2)
#endif
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
/*
* Canyonlands has 64MBytes of NOR FLASH (Spansion 29GL512), but the
* boot EBC mapping only supports a maximum of 16MBytes
* (4.ff00.0000 - 4.ffff.ffff).
* To solve this problem, the FLASH has to get remapped to another
* EBC address which accepts bigger regions:
*
* 0xfc00.0000 -> 4.cc00.0000
*
* Arches has 32MBytes of NOR FLASH (Spansion 29GL256), it will be
* remapped to:
*
* 0xfe00.0000 -> 4.ce00.0000
*/
/* Memory Bank 0 (NOR-FLASH) initialization */
#define CONFIG_SYS_EBC_PB0AP 0x10055e00
#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_BOOT_BASE_ADDR | 0x9a000)
#if !defined(CONFIG_ARCHES)
/* Memory Bank 3 (NAND-FLASH) initialization */
#define CONFIG_SYS_EBC_PB3AP 0x018003c0
#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_NAND_ADDR | 0x1E000) /* BAS=NAND,BS=1MB,BU=R/W,BW=32bit*/
#endif
#if !defined(CONFIG_ARCHES)
/* Memory Bank 2 (CPLD) initialization */
#define CONFIG_SYS_EBC_PB2AP 0x00804240
#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_BCSR_BASE | 0x18000) /* BAS=CPLD,BS=1M,BU=RW,BW=32bit */
#else /* defined(CONFIG_ARCHES) */
/* Memory Bank 1 (FPGA) initialization */
#define CONFIG_SYS_EBC_PB1AP 0x7f8ffe80
#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_FPGA_BASE | 0x3a000) /* BAS=FPGA,BS=2MB,BU=R/W,BW=16bit*/
#endif /* !defined(CONFIG_ARCHES) */
#define CONFIG_SYS_EBC_CFG 0xbfc00000
/*
* Arches doesn't use PerCS3 but GPIO43, so let's configure the GPIO
* pin multiplexing correctly
*/
#if defined(CONFIG_ARCHES)
#define GPIO43_USE GPIO_SEL /* On Arches this pin is used as GPIO */
#else
#define GPIO43_USE GPIO_ALT1 /* On Glacier this pin is used as ALT1 -> PerCS3 */
#endif
/*
* PPC4xx GPIO Configuration
*/
#ifdef CONFIG_460EX
/* 460EX: Use USB configuration */
#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
{ \
/* GPIO Core 0 */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 GMC1TxD(0) USB2HostD(0) */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 GMC1TxD(1) USB2HostD(1) */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO2 GMC1TxD(2) USB2HostD(2) */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO3 GMC1TxD(3) USB2HostD(3) */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO4 GMC1TxD(4) USB2HostD(4) */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO5 GMC1TxD(5) USB2HostD(5) */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO6 GMC1TxD(6) USB2HostD(6) */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 GMC1TxD(7) USB2HostD(7) */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 GMC1RxD(0) USB2OTGD(0) */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 GMC1RxD(1) USB2OTGD(1) */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 GMC1RxD(2) USB2OTGD(2) */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 GMC1RxD(3) USB2OTGD(3) */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO12 GMC1RxD(4) USB2OTGD(4) */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO13 GMC1RxD(5) USB2OTGD(5) */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO14 GMC1RxD(6) USB2OTGD(6) */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO15 GMC1RxD(7) USB2OTGD(7) */ \
{GPIO0_BASE, GPIO_IN , GPIO_SEL, GPIO_OUT_0}, /* GPIO16 GMC1TxER USB2HostStop */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 GMC1CD USB2HostNext */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 GMC1RxER USB2HostDir */ \
{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO19 GMC1TxEN USB2OTGStop */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 GMC1CRS USB2OTGNext */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 GMC1RxDV USB2OTGDir */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO22 NFRDY */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 NFREN */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO24 NFWEN */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO25 NFCLE */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 NFALE */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO27 IRQ(0) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO28 IRQ(1) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO29 IRQ(2) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO30 PerPar0 DMAReq2 IRQ(7)*/ \
{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO31 PerPar1 DMAAck2 IRQ(8)*/ \
}, \
{ \
/* GPIO Core 1 */ \
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO32 PerPar2 EOT2/TC2 IRQ(9)*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO33 PerPar3 DMAReq3 IRQ(4)*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT3, GPIO_OUT_1}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N DMAAck3 UART3_SIN*/ \
{GPIO1_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO37 UART0_RTS_N EOT3/TC3 UART3_SOUT*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N UART1_SIN */ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 IRQ(3) */ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 CS(1) */ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 CS(2) */ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 CS(3) DMAReq1 IRQ(10)*/ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO44 CS(4) DMAAck1 IRQ(11)*/ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO45 CS(5) EOT/TC1 IRQ(12)*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO46 PerAddr(5) DMAReq0 IRQ(13)*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO47 PerAddr(6) DMAAck0 IRQ(14)*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO48 PerAddr(7) EOT/TC0 IRQ(15)*/ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO49 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO50 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO53 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO54 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO55 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO56 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO57 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO62 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \
} \
}
#else
/* 460GT: Use EMAC2+3 configuration */
#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
{ \
/* GPIO Core 0 */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 GMC1TxD(0) USB2HostD(0) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 GMC1TxD(1) USB2HostD(1) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO2 GMC1TxD(2) USB2HostD(2) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO3 GMC1TxD(3) USB2HostD(3) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO4 GMC1TxD(4) USB2HostD(4) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO5 GMC1TxD(5) USB2HostD(5) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO6 GMC1TxD(6) USB2HostD(6) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 GMC1TxD(7) USB2HostD(7) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 GMC1RxD(0) USB2OTGD(0) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 GMC1RxD(1) USB2OTGD(1) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 GMC1RxD(2) USB2OTGD(2) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 GMC1RxD(3) USB2OTGD(3) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO12 GMC1RxD(4) USB2OTGD(4) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO13 GMC1RxD(5) USB2OTGD(5) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO14 GMC1RxD(6) USB2OTGD(6) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO15 GMC1RxD(7) USB2OTGD(7) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 GMC1TxER USB2HostStop */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 GMC1CD USB2HostNext */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 GMC1RxER USB2HostDir */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 GMC1TxEN USB2OTGStop */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 GMC1CRS USB2OTGNext */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 GMC1RxDV USB2OTGDir */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO22 NFRDY */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 NFREN */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO24 NFWEN */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO25 NFCLE */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 NFALE */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO27 IRQ(0) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO28 IRQ(1) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO29 IRQ(2) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO30 PerPar0 DMAReq2 IRQ(7)*/ \
{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO31 PerPar1 DMAAck2 IRQ(8)*/ \
}, \
{ \
/* GPIO Core 1 */ \
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO32 PerPar2 EOT2/TC2 IRQ(9)*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO33 PerPar3 DMAReq3 IRQ(4)*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT3, GPIO_OUT_1}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N DMAAck3 UART3_SIN*/ \
{GPIO1_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO37 UART0_RTS_N EOT3/TC3 UART3_SOUT*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N UART1_SIN */ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 IRQ(3) */ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 CS(1) */ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 CS(2) */ \
{GPIO1_BASE, GPIO_OUT, GPIO43_USE, GPIO_OUT_0},/* GPIO43 CS(3) DMAReq1 IRQ(10)*/ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO44 CS(4) DMAAck1 IRQ(11)*/ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO45 CS(5) EOT/TC1 IRQ(12)*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO46 PerAddr(5) DMAReq0 IRQ(13)*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO47 PerAddr(6) DMAAck0 IRQ(14)*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO48 PerAddr(7) EOT/TC0 IRQ(15)*/ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO49 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO50 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO53 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO54 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO55 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO56 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO57 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO62 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \
} \
}
#endif
#endif /* __CONFIG_H */