blob: 04a629125e0f429e5fc0be5f2d5d8260ece56b98 [file] [log] [blame]
/*
* (C) Copyright 2012-2013 Henrik Nordstrom <henrik@henriknordstrom.net>
* (C) Copyright 2013 Luke Kenneth Casson Leighton <lkcl@lkcl.net>
*
* (C) Copyright 2007-2011
* Allwinner Technology Co., Ltd. <www.allwinnertech.com>
* Tom Cubie <tangliang@allwinnertech.com>
*
* Some board init for the Allwinner A10-evb board.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <mmc.h>
#include <axp_pmic.h>
#include <asm/arch/clock.h>
#include <asm/arch/cpu.h>
#include <asm/arch/display.h>
#include <asm/arch/dram.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mmc.h>
#include <asm/arch/spl.h>
#include <asm/arch/usb_phy.h>
#ifndef CONFIG_ARM64
#include <asm/armv7.h>
#endif
#include <asm/gpio.h>
#include <asm/io.h>
#include <crc.h>
#include <environment.h>
#include <libfdt.h>
#include <nand.h>
#include <net.h>
#include <sy8106a.h>
#if defined CONFIG_VIDEO_LCD_PANEL_I2C && !(defined CONFIG_SPL_BUILD)
/* So that we can use pin names in Kconfig and sunxi_name_to_gpio() */
int soft_i2c_gpio_sda;
int soft_i2c_gpio_scl;
static int soft_i2c_board_init(void)
{
int ret;
soft_i2c_gpio_sda = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_PANEL_I2C_SDA);
if (soft_i2c_gpio_sda < 0) {
printf("Error invalid soft i2c sda pin: '%s', err %d\n",
CONFIG_VIDEO_LCD_PANEL_I2C_SDA, soft_i2c_gpio_sda);
return soft_i2c_gpio_sda;
}
ret = gpio_request(soft_i2c_gpio_sda, "soft-i2c-sda");
if (ret) {
printf("Error requesting soft i2c sda pin: '%s', err %d\n",
CONFIG_VIDEO_LCD_PANEL_I2C_SDA, ret);
return ret;
}
soft_i2c_gpio_scl = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_PANEL_I2C_SCL);
if (soft_i2c_gpio_scl < 0) {
printf("Error invalid soft i2c scl pin: '%s', err %d\n",
CONFIG_VIDEO_LCD_PANEL_I2C_SCL, soft_i2c_gpio_scl);
return soft_i2c_gpio_scl;
}
ret = gpio_request(soft_i2c_gpio_scl, "soft-i2c-scl");
if (ret) {
printf("Error requesting soft i2c scl pin: '%s', err %d\n",
CONFIG_VIDEO_LCD_PANEL_I2C_SCL, ret);
return ret;
}
return 0;
}
#else
static int soft_i2c_board_init(void) { return 0; }
#endif
DECLARE_GLOBAL_DATA_PTR;
/* add board specific code here */
int board_init(void)
{
__maybe_unused int id_pfr1, ret, satapwr_pin, macpwr_pin;
gd->bd->bi_boot_params = (PHYS_SDRAM_0 + 0x100);
#ifndef CONFIG_ARM64
asm volatile("mrc p15, 0, %0, c0, c1, 1" : "=r"(id_pfr1));
debug("id_pfr1: 0x%08x\n", id_pfr1);
/* Generic Timer Extension available? */
if ((id_pfr1 >> CPUID_ARM_GENTIMER_SHIFT) & 0xf) {
uint32_t freq;
debug("Setting CNTFRQ\n");
/*
* CNTFRQ is a secure register, so we will crash if we try to
* write this from the non-secure world (read is OK, though).
* In case some bootcode has already set the correct value,
* we avoid the risk of writing to it.
*/
asm volatile("mrc p15, 0, %0, c14, c0, 0" : "=r"(freq));
if (freq != COUNTER_FREQUENCY) {
debug("arch timer frequency is %d Hz, should be %d, fixing ...\n",
freq, COUNTER_FREQUENCY);
#ifdef CONFIG_NON_SECURE
printf("arch timer frequency is wrong, but cannot adjust it\n");
#else
asm volatile("mcr p15, 0, %0, c14, c0, 0"
: : "r"(COUNTER_FREQUENCY));
#endif
}
}
#endif /* !CONFIG_ARM64 */
ret = axp_gpio_init();
if (ret)
return ret;
#ifdef CONFIG_SATAPWR
satapwr_pin = sunxi_name_to_gpio(CONFIG_SATAPWR);
gpio_request(satapwr_pin, "satapwr");
gpio_direction_output(satapwr_pin, 1);
#endif
#ifdef CONFIG_MACPWR
macpwr_pin = sunxi_name_to_gpio(CONFIG_MACPWR);
gpio_request(macpwr_pin, "macpwr");
gpio_direction_output(macpwr_pin, 1);
#endif
/* Uses dm gpio code so do this here and not in i2c_init_board() */
return soft_i2c_board_init();
}
int dram_init(void)
{
gd->ram_size = get_ram_size((long *)PHYS_SDRAM_0, PHYS_SDRAM_0_SIZE);
return 0;
}
#if defined(CONFIG_NAND_SUNXI)
static void nand_pinmux_setup(void)
{
unsigned int pin;
for (pin = SUNXI_GPC(0); pin <= SUNXI_GPC(19); pin++)
sunxi_gpio_set_cfgpin(pin, SUNXI_GPC_NAND);
#if defined CONFIG_MACH_SUN4I || defined CONFIG_MACH_SUN7I
for (pin = SUNXI_GPC(20); pin <= SUNXI_GPC(22); pin++)
sunxi_gpio_set_cfgpin(pin, SUNXI_GPC_NAND);
#endif
/* sun4i / sun7i do have a PC23, but it is not used for nand,
* only sun7i has a PC24 */
#ifdef CONFIG_MACH_SUN7I
sunxi_gpio_set_cfgpin(SUNXI_GPC(24), SUNXI_GPC_NAND);
#endif
}
static void nand_clock_setup(void)
{
struct sunxi_ccm_reg *const ccm =
(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
setbits_le32(&ccm->ahb_gate0, (CLK_GATE_OPEN << AHB_GATE_OFFSET_NAND0));
#ifdef CONFIG_MACH_SUN9I
setbits_le32(&ccm->ahb_gate1, (1 << AHB_GATE_OFFSET_DMA));
#else
setbits_le32(&ccm->ahb_gate0, (1 << AHB_GATE_OFFSET_DMA));
#endif
setbits_le32(&ccm->nand0_clk_cfg, CCM_NAND_CTRL_ENABLE | AHB_DIV_1);
}
void board_nand_init(void)
{
nand_pinmux_setup();
nand_clock_setup();
#ifndef CONFIG_SPL_BUILD
sunxi_nand_init();
#endif
}
#endif
#ifdef CONFIG_GENERIC_MMC
static void mmc_pinmux_setup(int sdc)
{
unsigned int pin;
__maybe_unused int pins;
switch (sdc) {
case 0:
/* SDC0: PF0-PF5 */
for (pin = SUNXI_GPF(0); pin <= SUNXI_GPF(5); pin++) {
sunxi_gpio_set_cfgpin(pin, SUNXI_GPF_SDC0);
sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(pin, 2);
}
break;
case 1:
pins = sunxi_name_to_gpio_bank(CONFIG_MMC1_PINS);
#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I) || \
defined(CONFIG_MACH_SUN8I_R40)
if (pins == SUNXI_GPIO_H) {
/* SDC1: PH22-PH-27 */
for (pin = SUNXI_GPH(22); pin <= SUNXI_GPH(27); pin++) {
sunxi_gpio_set_cfgpin(pin, SUN4I_GPH_SDC1);
sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(pin, 2);
}
} else {
/* SDC1: PG0-PG5 */
for (pin = SUNXI_GPG(0); pin <= SUNXI_GPG(5); pin++) {
sunxi_gpio_set_cfgpin(pin, SUN4I_GPG_SDC1);
sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(pin, 2);
}
}
#elif defined(CONFIG_MACH_SUN5I)
/* SDC1: PG3-PG8 */
for (pin = SUNXI_GPG(3); pin <= SUNXI_GPG(8); pin++) {
sunxi_gpio_set_cfgpin(pin, SUN5I_GPG_SDC1);
sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(pin, 2);
}
#elif defined(CONFIG_MACH_SUN6I)
/* SDC1: PG0-PG5 */
for (pin = SUNXI_GPG(0); pin <= SUNXI_GPG(5); pin++) {
sunxi_gpio_set_cfgpin(pin, SUN6I_GPG_SDC1);
sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(pin, 2);
}
#elif defined(CONFIG_MACH_SUN8I)
if (pins == SUNXI_GPIO_D) {
/* SDC1: PD2-PD7 */
for (pin = SUNXI_GPD(2); pin <= SUNXI_GPD(7); pin++) {
sunxi_gpio_set_cfgpin(pin, SUN8I_GPD_SDC1);
sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(pin, 2);
}
} else {
/* SDC1: PG0-PG5 */
for (pin = SUNXI_GPG(0); pin <= SUNXI_GPG(5); pin++) {
sunxi_gpio_set_cfgpin(pin, SUN8I_GPG_SDC1);
sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(pin, 2);
}
}
#endif
break;
case 2:
pins = sunxi_name_to_gpio_bank(CONFIG_MMC2_PINS);
#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I)
/* SDC2: PC6-PC11 */
for (pin = SUNXI_GPC(6); pin <= SUNXI_GPC(11); pin++) {
sunxi_gpio_set_cfgpin(pin, SUNXI_GPC_SDC2);
sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(pin, 2);
}
#elif defined(CONFIG_MACH_SUN5I)
if (pins == SUNXI_GPIO_E) {
/* SDC2: PE4-PE9 */
for (pin = SUNXI_GPE(4); pin <= SUNXI_GPD(9); pin++) {
sunxi_gpio_set_cfgpin(pin, SUN5I_GPE_SDC2);
sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(pin, 2);
}
} else {
/* SDC2: PC6-PC15 */
for (pin = SUNXI_GPC(6); pin <= SUNXI_GPC(15); pin++) {
sunxi_gpio_set_cfgpin(pin, SUNXI_GPC_SDC2);
sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(pin, 2);
}
}
#elif defined(CONFIG_MACH_SUN6I)
if (pins == SUNXI_GPIO_A) {
/* SDC2: PA9-PA14 */
for (pin = SUNXI_GPA(9); pin <= SUNXI_GPA(14); pin++) {
sunxi_gpio_set_cfgpin(pin, SUN6I_GPA_SDC2);
sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(pin, 2);
}
} else {
/* SDC2: PC6-PC15, PC24 */
for (pin = SUNXI_GPC(6); pin <= SUNXI_GPC(15); pin++) {
sunxi_gpio_set_cfgpin(pin, SUNXI_GPC_SDC2);
sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(pin, 2);
}
sunxi_gpio_set_cfgpin(SUNXI_GPC(24), SUNXI_GPC_SDC2);
sunxi_gpio_set_pull(SUNXI_GPC(24), SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(SUNXI_GPC(24), 2);
}
#elif defined(CONFIG_MACH_SUN8I_R40)
/* SDC2: PC6-PC15, PC24 */
for (pin = SUNXI_GPC(6); pin <= SUNXI_GPC(15); pin++) {
sunxi_gpio_set_cfgpin(pin, SUNXI_GPC_SDC2);
sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(pin, 2);
}
sunxi_gpio_set_cfgpin(SUNXI_GPC(24), SUNXI_GPC_SDC2);
sunxi_gpio_set_pull(SUNXI_GPC(24), SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(SUNXI_GPC(24), 2);
#elif defined(CONFIG_MACH_SUN8I) || defined(CONFIG_MACH_SUN50I)
/* SDC2: PC5-PC6, PC8-PC16 */
for (pin = SUNXI_GPC(5); pin <= SUNXI_GPC(6); pin++) {
sunxi_gpio_set_cfgpin(pin, SUNXI_GPC_SDC2);
sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(pin, 2);
}
for (pin = SUNXI_GPC(8); pin <= SUNXI_GPC(16); pin++) {
sunxi_gpio_set_cfgpin(pin, SUNXI_GPC_SDC2);
sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(pin, 2);
}
#elif defined(CONFIG_MACH_SUN9I)
/* SDC2: PC6-PC16 */
for (pin = SUNXI_GPC(6); pin <= SUNXI_GPC(16); pin++) {
sunxi_gpio_set_cfgpin(pin, SUNXI_GPC_SDC2);
sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(pin, 2);
}
#endif
break;
case 3:
pins = sunxi_name_to_gpio_bank(CONFIG_MMC3_PINS);
#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I) || \
defined(CONFIG_MACH_SUN8I_R40)
/* SDC3: PI4-PI9 */
for (pin = SUNXI_GPI(4); pin <= SUNXI_GPI(9); pin++) {
sunxi_gpio_set_cfgpin(pin, SUNXI_GPI_SDC3);
sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(pin, 2);
}
#elif defined(CONFIG_MACH_SUN6I)
if (pins == SUNXI_GPIO_A) {
/* SDC3: PA9-PA14 */
for (pin = SUNXI_GPA(9); pin <= SUNXI_GPA(14); pin++) {
sunxi_gpio_set_cfgpin(pin, SUN6I_GPA_SDC3);
sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(pin, 2);
}
} else {
/* SDC3: PC6-PC15, PC24 */
for (pin = SUNXI_GPC(6); pin <= SUNXI_GPC(15); pin++) {
sunxi_gpio_set_cfgpin(pin, SUN6I_GPC_SDC3);
sunxi_gpio_set_pull(pin, SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(pin, 2);
}
sunxi_gpio_set_cfgpin(SUNXI_GPC(24), SUN6I_GPC_SDC3);
sunxi_gpio_set_pull(SUNXI_GPC(24), SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(SUNXI_GPC(24), 2);
}
#endif
break;
default:
printf("sunxi: invalid MMC slot %d for pinmux setup\n", sdc);
break;
}
}
int board_mmc_init(bd_t *bis)
{
__maybe_unused struct mmc *mmc0, *mmc1;
__maybe_unused char buf[512];
mmc_pinmux_setup(CONFIG_MMC_SUNXI_SLOT);
mmc0 = sunxi_mmc_init(CONFIG_MMC_SUNXI_SLOT);
if (!mmc0)
return -1;
#if CONFIG_MMC_SUNXI_SLOT_EXTRA != -1
mmc_pinmux_setup(CONFIG_MMC_SUNXI_SLOT_EXTRA);
mmc1 = sunxi_mmc_init(CONFIG_MMC_SUNXI_SLOT_EXTRA);
if (!mmc1)
return -1;
#endif
#if !defined(CONFIG_SPL_BUILD) && CONFIG_MMC_SUNXI_SLOT_EXTRA == 2
/*
* On systems with an emmc (mmc2), figure out if we are booting from
* the emmc and if we are make it "mmc dev 0" so that boot.scr, etc.
* are searched there first. Note we only do this for u-boot proper,
* not for the SPL, see spl_boot_device().
*/
if (readb(SPL_ADDR + 0x28) == SUNXI_BOOTED_FROM_MMC2) {
/* Booting from emmc / mmc2, swap */
mmc0->block_dev.devnum = 1;
mmc1->block_dev.devnum = 0;
}
#endif
return 0;
}
#endif
void i2c_init_board(void)
{
#ifdef CONFIG_I2C0_ENABLE
#if defined(CONFIG_MACH_SUN4I) || \
defined(CONFIG_MACH_SUN5I) || \
defined(CONFIG_MACH_SUN7I) || \
defined(CONFIG_MACH_SUN8I_R40)
sunxi_gpio_set_cfgpin(SUNXI_GPB(0), SUN4I_GPB_TWI0);
sunxi_gpio_set_cfgpin(SUNXI_GPB(1), SUN4I_GPB_TWI0);
clock_twi_onoff(0, 1);
#elif defined(CONFIG_MACH_SUN6I)
sunxi_gpio_set_cfgpin(SUNXI_GPH(14), SUN6I_GPH_TWI0);
sunxi_gpio_set_cfgpin(SUNXI_GPH(15), SUN6I_GPH_TWI0);
clock_twi_onoff(0, 1);
#elif defined(CONFIG_MACH_SUN8I)
sunxi_gpio_set_cfgpin(SUNXI_GPH(2), SUN8I_GPH_TWI0);
sunxi_gpio_set_cfgpin(SUNXI_GPH(3), SUN8I_GPH_TWI0);
clock_twi_onoff(0, 1);
#endif
#endif
#ifdef CONFIG_I2C1_ENABLE
#if defined(CONFIG_MACH_SUN4I) || \
defined(CONFIG_MACH_SUN7I) || \
defined(CONFIG_MACH_SUN8I_R40)
sunxi_gpio_set_cfgpin(SUNXI_GPB(18), SUN4I_GPB_TWI1);
sunxi_gpio_set_cfgpin(SUNXI_GPB(19), SUN4I_GPB_TWI1);
clock_twi_onoff(1, 1);
#elif defined(CONFIG_MACH_SUN5I)
sunxi_gpio_set_cfgpin(SUNXI_GPB(15), SUN5I_GPB_TWI1);
sunxi_gpio_set_cfgpin(SUNXI_GPB(16), SUN5I_GPB_TWI1);
clock_twi_onoff(1, 1);
#elif defined(CONFIG_MACH_SUN6I)
sunxi_gpio_set_cfgpin(SUNXI_GPH(16), SUN6I_GPH_TWI1);
sunxi_gpio_set_cfgpin(SUNXI_GPH(17), SUN6I_GPH_TWI1);
clock_twi_onoff(1, 1);
#elif defined(CONFIG_MACH_SUN8I)
sunxi_gpio_set_cfgpin(SUNXI_GPH(4), SUN8I_GPH_TWI1);
sunxi_gpio_set_cfgpin(SUNXI_GPH(5), SUN8I_GPH_TWI1);
clock_twi_onoff(1, 1);
#endif
#endif
#ifdef CONFIG_I2C2_ENABLE
#if defined(CONFIG_MACH_SUN4I) || \
defined(CONFIG_MACH_SUN7I) || \
defined(CONFIG_MACH_SUN8I_R40)
sunxi_gpio_set_cfgpin(SUNXI_GPB(20), SUN4I_GPB_TWI2);
sunxi_gpio_set_cfgpin(SUNXI_GPB(21), SUN4I_GPB_TWI2);
clock_twi_onoff(2, 1);
#elif defined(CONFIG_MACH_SUN5I)
sunxi_gpio_set_cfgpin(SUNXI_GPB(17), SUN5I_GPB_TWI2);
sunxi_gpio_set_cfgpin(SUNXI_GPB(18), SUN5I_GPB_TWI2);
clock_twi_onoff(2, 1);
#elif defined(CONFIG_MACH_SUN6I)
sunxi_gpio_set_cfgpin(SUNXI_GPH(18), SUN6I_GPH_TWI2);
sunxi_gpio_set_cfgpin(SUNXI_GPH(19), SUN6I_GPH_TWI2);
clock_twi_onoff(2, 1);
#elif defined(CONFIG_MACH_SUN8I)
sunxi_gpio_set_cfgpin(SUNXI_GPE(12), SUN8I_GPE_TWI2);
sunxi_gpio_set_cfgpin(SUNXI_GPE(13), SUN8I_GPE_TWI2);
clock_twi_onoff(2, 1);
#endif
#endif
#ifdef CONFIG_I2C3_ENABLE
#if defined(CONFIG_MACH_SUN6I)
sunxi_gpio_set_cfgpin(SUNXI_GPG(10), SUN6I_GPG_TWI3);
sunxi_gpio_set_cfgpin(SUNXI_GPG(11), SUN6I_GPG_TWI3);
clock_twi_onoff(3, 1);
#elif defined(CONFIG_MACH_SUN7I) || \
defined(CONFIG_MACH_SUN8I_R40)
sunxi_gpio_set_cfgpin(SUNXI_GPI(0), SUN7I_GPI_TWI3);
sunxi_gpio_set_cfgpin(SUNXI_GPI(1), SUN7I_GPI_TWI3);
clock_twi_onoff(3, 1);
#endif
#endif
#ifdef CONFIG_I2C4_ENABLE
#if defined(CONFIG_MACH_SUN7I) || \
defined(CONFIG_MACH_SUN8I_R40)
sunxi_gpio_set_cfgpin(SUNXI_GPI(2), SUN7I_GPI_TWI4);
sunxi_gpio_set_cfgpin(SUNXI_GPI(3), SUN7I_GPI_TWI4);
clock_twi_onoff(4, 1);
#endif
#endif
#ifdef CONFIG_R_I2C_ENABLE
clock_twi_onoff(5, 1);
sunxi_gpio_set_cfgpin(SUNXI_GPL(0), SUN8I_H3_GPL_R_TWI);
sunxi_gpio_set_cfgpin(SUNXI_GPL(1), SUN8I_H3_GPL_R_TWI);
#endif
}
#ifdef CONFIG_SPL_BUILD
void sunxi_board_init(void)
{
int power_failed = 0;
unsigned long ramsize;
#ifdef CONFIG_SY8106A_POWER
power_failed = sy8106a_set_vout1(CONFIG_SY8106A_VOUT1_VOLT);
#endif
#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || \
defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
defined CONFIG_AXP818_POWER
power_failed = axp_init();
#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
defined CONFIG_AXP818_POWER
power_failed |= axp_set_dcdc1(CONFIG_AXP_DCDC1_VOLT);
#endif
power_failed |= axp_set_dcdc2(CONFIG_AXP_DCDC2_VOLT);
power_failed |= axp_set_dcdc3(CONFIG_AXP_DCDC3_VOLT);
#if !defined(CONFIG_AXP209_POWER) && !defined(CONFIG_AXP818_POWER)
power_failed |= axp_set_dcdc4(CONFIG_AXP_DCDC4_VOLT);
#endif
#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
defined CONFIG_AXP818_POWER
power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
#endif
#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
defined CONFIG_AXP818_POWER
power_failed |= axp_set_aldo1(CONFIG_AXP_ALDO1_VOLT);
#endif
power_failed |= axp_set_aldo2(CONFIG_AXP_ALDO2_VOLT);
#if !defined(CONFIG_AXP152_POWER)
power_failed |= axp_set_aldo3(CONFIG_AXP_ALDO3_VOLT);
#endif
#ifdef CONFIG_AXP209_POWER
power_failed |= axp_set_aldo4(CONFIG_AXP_ALDO4_VOLT);
#endif
#if defined(CONFIG_AXP221_POWER) || defined(CONFIG_AXP809_POWER) || \
defined(CONFIG_AXP818_POWER)
power_failed |= axp_set_dldo(1, CONFIG_AXP_DLDO1_VOLT);
power_failed |= axp_set_dldo(2, CONFIG_AXP_DLDO2_VOLT);
#if !defined CONFIG_AXP809_POWER
power_failed |= axp_set_dldo(3, CONFIG_AXP_DLDO3_VOLT);
power_failed |= axp_set_dldo(4, CONFIG_AXP_DLDO4_VOLT);
#endif
power_failed |= axp_set_eldo(1, CONFIG_AXP_ELDO1_VOLT);
power_failed |= axp_set_eldo(2, CONFIG_AXP_ELDO2_VOLT);
power_failed |= axp_set_eldo(3, CONFIG_AXP_ELDO3_VOLT);
#endif
#ifdef CONFIG_AXP818_POWER
power_failed |= axp_set_fldo(1, CONFIG_AXP_FLDO1_VOLT);
power_failed |= axp_set_fldo(2, CONFIG_AXP_FLDO2_VOLT);
power_failed |= axp_set_fldo(3, CONFIG_AXP_FLDO3_VOLT);
#endif
#if defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
power_failed |= axp_set_sw(IS_ENABLED(CONFIG_AXP_SW_ON));
#endif
#endif
printf("DRAM:");
ramsize = sunxi_dram_init();
printf(" %d MiB\n", (int)(ramsize >> 20));
if (!ramsize)
hang();
/*
* Only clock up the CPU to full speed if we are reasonably
* assured it's being powered with suitable core voltage
*/
if (!power_failed)
clock_set_pll1(CONFIG_SYS_CLK_FREQ);
else
printf("Failed to set core voltage! Can't set CPU frequency\n");
}
#endif
#ifdef CONFIG_USB_GADGET
int g_dnl_board_usb_cable_connected(void)
{
return sunxi_usb_phy_vbus_detect(0);
}
#endif
#ifdef CONFIG_SERIAL_TAG
void get_board_serial(struct tag_serialnr *serialnr)
{
char *serial_string;
unsigned long long serial;
serial_string = getenv("serial#");
if (serial_string) {
serial = simple_strtoull(serial_string, NULL, 16);
serialnr->high = (unsigned int) (serial >> 32);
serialnr->low = (unsigned int) (serial & 0xffffffff);
} else {
serialnr->high = 0;
serialnr->low = 0;
}
}
#endif
/*
* Check the SPL header for the "sunxi" variant. If found: parse values
* that might have been passed by the loader ("fel" utility), and update
* the environment accordingly.
*/
static void parse_spl_header(const uint32_t spl_addr)
{
struct boot_file_head *spl = (void *)(ulong)spl_addr;
if (memcmp(spl->spl_signature, SPL_SIGNATURE, 3) != 0)
return; /* signature mismatch, no usable header */
uint8_t spl_header_version = spl->spl_signature[3];
if (spl_header_version != SPL_HEADER_VERSION) {
printf("sunxi SPL version mismatch: expected %u, got %u\n",
SPL_HEADER_VERSION, spl_header_version);
return;
}
if (!spl->fel_script_address)
return;
if (spl->fel_uEnv_length != 0) {
/*
* data is expected in uEnv.txt compatible format, so "env
* import -t" the string(s) at fel_script_address right away.
*/
himport_r(&env_htab, (char *)(uintptr_t)spl->fel_script_address,
spl->fel_uEnv_length, '\n', H_NOCLEAR, 0, 0, NULL);
return;
}
/* otherwise assume .scr format (mkimage-type script) */
setenv_hex("fel_scriptaddr", spl->fel_script_address);
}
/*
* Note this function gets called multiple times.
* It must not make any changes to env variables which already exist.
*/
static void setup_environment(const void *fdt)
{
char serial_string[17] = { 0 };
unsigned int sid[4];
uint8_t mac_addr[6];
char ethaddr[16];
int i, ret;
ret = sunxi_get_sid(sid);
if (ret == 0 && sid[0] != 0) {
/*
* The single words 1 - 3 of the SID have quite a few bits
* which are the same on many models, so we take a crc32
* of all 3 words, to get a more unique value.
*
* Note we only do this on newer SoCs as we cannot change
* the algorithm on older SoCs since those have been using
* fixed mac-addresses based on only using word 3 for a
* long time and changing a fixed mac-address with an
* u-boot update is not good.
*/
#if !defined(CONFIG_MACH_SUN4I) && !defined(CONFIG_MACH_SUN5I) && \
!defined(CONFIG_MACH_SUN6I) && !defined(CONFIG_MACH_SUN7I) && \
!defined(CONFIG_MACH_SUN8I_A23) && !defined(CONFIG_MACH_SUN8I_A33)
sid[3] = crc32(0, (unsigned char *)&sid[1], 12);
#endif
/* Ensure the NIC specific bytes of the mac are not all 0 */
if ((sid[3] & 0xffffff) == 0)
sid[3] |= 0x800000;
for (i = 0; i < 4; i++) {
sprintf(ethaddr, "ethernet%d", i);
if (!fdt_get_alias(fdt, ethaddr))
continue;
if (i == 0)
strcpy(ethaddr, "ethaddr");
else
sprintf(ethaddr, "eth%daddr", i);
if (getenv(ethaddr))
continue;
/* Non OUI / registered MAC address */
mac_addr[0] = (i << 4) | 0x02;
mac_addr[1] = (sid[0] >> 0) & 0xff;
mac_addr[2] = (sid[3] >> 24) & 0xff;
mac_addr[3] = (sid[3] >> 16) & 0xff;
mac_addr[4] = (sid[3] >> 8) & 0xff;
mac_addr[5] = (sid[3] >> 0) & 0xff;
eth_setenv_enetaddr(ethaddr, mac_addr);
}
if (!getenv("serial#")) {
snprintf(serial_string, sizeof(serial_string),
"%08x%08x", sid[0], sid[3]);
setenv("serial#", serial_string);
}
}
}
int misc_init_r(void)
{
__maybe_unused int ret;
setenv("fel_booted", NULL);
setenv("fel_scriptaddr", NULL);
/* determine if we are running in FEL mode */
if (!is_boot0_magic(SPL_ADDR + 4)) { /* eGON.BT0 */
setenv("fel_booted", "1");
parse_spl_header(SPL_ADDR);
}
setup_environment(gd->fdt_blob);
#ifndef CONFIG_MACH_SUN9I
ret = sunxi_usb_phy_probe();
if (ret)
return ret;
#endif
sunxi_musb_board_init();
return 0;
}
int ft_board_setup(void *blob, bd_t *bd)
{
int __maybe_unused r;
/*
* Call setup_environment again in case the boot fdt has
* ethernet aliases the u-boot copy does not have.
*/
setup_environment(blob);
#ifdef CONFIG_VIDEO_DT_SIMPLEFB
r = sunxi_simplefb_setup(blob);
if (r)
return r;
#endif
return 0;
}