drivers/net/ksz9477.c - mirrors/cros/chromiumos/third_party/u-boot - Git at Google

 // SPDX-License-Identifier: GPL-2.0+
 /*
  * (C) Copyright 2020
  * Tim Harvey, Gateworks Corporation
  */

 #include <dm.h>
 #include <dm/device_compat.h>
 #include <dm/device-internal.h>
 #include <dm/lists.h>
 #include <eth_phy.h>
 #include <linux/delay.h>
 #include <miiphy.h>
 #include <i2c.h>
 #include <net/dsa.h>

 #include <asm-generic/gpio.h>

 /* Global registers */

 /* Chip ID */
 #define REG_CHIP_ID0__1			0x0000

 /* Operation control */
 #define REG_SW_OPERATION		0x0300
 #define SW_RESET			BIT(1)
 #define SW_START			BIT(0)

 /* Port Specific Registers */
 #define PORT_CTRL_ADDR(port, addr) ((addr) | (((port) + 1) << 12))

 /* Port Control */
 #define REG_PORT_XMII_CTRL_1		0x0301
 #define PORT_MII_NOT_1GBIT		BIT(6)
 #define PORT_MII_SEL_EDGE		BIT(5)
 #define PORT_RGMII_ID_IG_ENABLE		BIT(4)
 #define PORT_RGMII_ID_EG_ENABLE		BIT(3)
 #define PORT_MII_MAC_MODE		BIT(2)
 #define PORT_MII_SEL_M			0x3
 #define PORT_RGMII_SEL			0x0
 #define PORT_RMII_SEL			0x1
 #define PORT_GMII_SEL			0x2
 #define PORT_MII_SEL			0x3

 /* Port MSTP State Register */
 #define REG_PORT_MSTP_STATE		0x0b04
 #define PORT_TX_ENABLE			BIT(2)
 #define PORT_RX_ENABLE			BIT(1)
 #define PORT_LEARN_DISABLE		BIT(0)

 /* MMD */
 #define REG_PORT_PHY_MMD_SETUP		0x011A
 #define PORT_MMD_OP_MODE_M		0x3
 #define PORT_MMD_OP_MODE_S		14
 #define PORT_MMD_OP_INDEX		0
 #define PORT_MMD_OP_DATA_NO_INCR	1
 #define PORT_MMD_OP_DATA_INCR_RW	2
 #define PORT_MMD_OP_DATA_INCR_W		3
 #define PORT_MMD_DEVICE_ID_M		0x1F
 #define MMD_SETUP(mode, dev)		(((u16)(mode) << PORT_MMD_OP_MODE_S) | (dev))
 #define REG_PORT_PHY_MMD_INDEX_DATA	0x011C

 struct ksz_dsa_priv {
 	struct udevice *dev;
 	int active_port;
 };

 static inline int ksz_read8(struct udevice *dev, u32 reg, u8 *val)
 {
 	int ret = dm_i2c_read(dev, reg, val, 1);

 	dev_dbg(dev, "%s 0x%04x<<0x%02x\n", __func__, reg, *val);

 	return ret;
 }

 static inline int ksz_pread8(struct udevice *dev, int port, int reg, u8 *val)
 {
 	return ksz_read8(dev, PORT_CTRL_ADDR(port, reg), val);
 }

 static inline int ksz_write8(struct udevice *dev, u32 reg, u8 val)
 {
 	dev_dbg(dev, "%s 0x%04x>>0x%02x\n", __func__, reg, val);
 	return dm_i2c_write(dev, reg, &val, 1);
 }

 static inline int ksz_pwrite8(struct udevice *dev, int port, int reg, u8 val)
 {
 	return ksz_write8(dev, PORT_CTRL_ADDR(port, reg), val);
 }

 static inline int ksz_write16(struct udevice *dev, u32 reg, u16 val)
 {
 	u8 buf[2];

 	buf[1] = val & 0xff;
 	buf[0] = val >> 8;
 	dev_dbg(dev, "%s 0x%04x>>0x%04x\n", __func__, reg, val);

 	return dm_i2c_write(dev, reg, buf, 2);
 }

 static inline int ksz_pwrite16(struct udevice *dev, int port, int reg, u16 val)
 {
 	return ksz_write16(dev, PORT_CTRL_ADDR(port, reg), val);
 }

 static inline int ksz_read16(struct udevice *dev, u32 reg, u16 *val)
 {
 	u8 buf[2];
 	int ret;

 	ret = dm_i2c_read(dev, reg, buf, 2);
 	*val = (buf[0] << 8) | buf[1];
 	dev_dbg(dev, "%s 0x%04x<<0x%04x\n", __func__, reg, *val);

 	return ret;
 }

 static inline int ksz_pread16(struct udevice *dev, int port, int reg, u16 *val)
 {
 	return ksz_read16(dev, PORT_CTRL_ADDR(port, reg), val);
 }

 static inline int ksz_read32(struct udevice *dev, u32 reg, u32 *val)
 {
 	return dm_i2c_read(dev, reg, (u8 *)val, 4);
 }

 static inline int ksz_pread32(struct udevice *dev, int port, int reg, u32 *val)
 {
 	return ksz_read32(dev, PORT_CTRL_ADDR(port, reg), val);
 }

 static inline int ksz_write32(struct udevice *dev, u32 reg, u32 val)
 {
 	u8 buf[4];

 	buf[3] = val & 0xff;
 	buf[2] = (val >> 24) & 0xff;
 	buf[1] = (val >> 16) & 0xff;
 	buf[0] = (val >> 8) & 0xff;
 	dev_dbg(dev, "%s 0x%04x>>0x%04x\n", __func__, reg, val);

 	return dm_i2c_write(dev, reg, buf, 4);
 }

 static inline int ksz_pwrite32(struct udevice *dev, int port, int reg, u32 val)
 {
 	return ksz_write32(dev, PORT_CTRL_ADDR(port, reg), val);
 }

 static __maybe_unused void ksz_port_mmd_read(struct udevice *dev, int port,
 					     u8 addr, u16 reg, u16 *val)
 {
 	ksz_pwrite16(dev, port, REG_PORT_PHY_MMD_SETUP, MMD_SETUP(PORT_MMD_OP_INDEX, addr));
 	ksz_pwrite16(dev, port, REG_PORT_PHY_MMD_INDEX_DATA, reg);
 	ksz_pwrite16(dev, port, REG_PORT_PHY_MMD_SETUP, MMD_SETUP(PORT_MMD_OP_DATA_NO_INCR, addr));
 	ksz_pread16(dev, port, REG_PORT_PHY_MMD_INDEX_DATA, val);
 	dev_dbg(dev, "%s  P%d 0x%02x:0x%04x<<0x%04x\n", __func__, port + 1, addr, reg, *val);
 }

 static void ksz_port_mmd_write(struct udevice *dev, int port, u8 addr, u16 reg, u16 val)
 {
 	dev_dbg(dev, "%s P%d 0x%02x:0x%04x>>0x%04x\n", __func__, port + 1, addr, addr, val);
 	ksz_pwrite16(dev, port, REG_PORT_PHY_MMD_SETUP, MMD_SETUP(PORT_MMD_OP_INDEX, addr));
 	ksz_pwrite16(dev, port, REG_PORT_PHY_MMD_INDEX_DATA, addr);
 	ksz_pwrite16(dev, port, REG_PORT_PHY_MMD_SETUP, MMD_SETUP(PORT_MMD_OP_DATA_NO_INCR, addr));
 	ksz_pwrite16(dev, port, REG_PORT_PHY_MMD_INDEX_DATA, val);
 }

 /* Apply PHY settings to address errata listed in KSZ9477, KSZ9897, KSZ9896, KSZ9567
  * Silicon Errata and Data Sheet Clarification documents
  */
 static void ksz_phy_errata_setup(struct udevice *dev, int port)
 {
 	dev_dbg(dev, "%s P%d\n", __func__, port + 1);

 	/* Register settings are needed to improve PHY receive performance */
 	ksz_port_mmd_write(dev, port, 0x01, 0x6f, 0xdd0b);
 	ksz_port_mmd_write(dev, port, 0x01, 0x8f, 0x6032);
 	ksz_port_mmd_write(dev, port, 0x01, 0x9d, 0x248c);
 	ksz_port_mmd_write(dev, port, 0x01, 0x75, 0x0060);
 	ksz_port_mmd_write(dev, port, 0x01, 0xd3, 0x7777);
 	ksz_port_mmd_write(dev, port, 0x1c, 0x06, 0x3008);
 	ksz_port_mmd_write(dev, port, 0x1c, 0x08, 0x2001);

 	/* Transmit waveform amplitude can be improved (1000BASE-T, 100BASE-TX, 10BASE-Te) */
 	ksz_port_mmd_write(dev, port, 0x1c, 0x04, 0x00d0);

 	/* Energy Efficient Ethernet (EEE) feature select must be manually disabled */
 	ksz_port_mmd_write(dev, port, 0x07, 0x3c, 0x0000);

 	/* Register settings are required to meet data sheet supply current specifications */
 	ksz_port_mmd_write(dev, port, 0x1c, 0x13, 0x6eff);
 	ksz_port_mmd_write(dev, port, 0x1c, 0x14, 0xe6ff);
 	ksz_port_mmd_write(dev, port, 0x1c, 0x15, 0x6eff);
 	ksz_port_mmd_write(dev, port, 0x1c, 0x16, 0xe6ff);
 	ksz_port_mmd_write(dev, port, 0x1c, 0x17, 0x00ff);
 	ksz_port_mmd_write(dev, port, 0x1c, 0x18, 0x43ff);
 	ksz_port_mmd_write(dev, port, 0x1c, 0x19, 0xc3ff);
 	ksz_port_mmd_write(dev, port, 0x1c, 0x1a, 0x6fff);
 	ksz_port_mmd_write(dev, port, 0x1c, 0x1b, 0x07ff);
 	ksz_port_mmd_write(dev, port, 0x1c, 0x1c, 0x0fff);
 	ksz_port_mmd_write(dev, port, 0x1c, 0x1d, 0xe7ff);
 	ksz_port_mmd_write(dev, port, 0x1c, 0x1e, 0xefff);
 	ksz_port_mmd_write(dev, port, 0x1c, 0x20, 0xeeee);
 }

 /*
  * mii bus driver
  */
 #define KSZ_MDIO_CHILD_DRV_NAME	"ksz_mdio"

 struct ksz_mdio_priv {
 	struct ksz_dsa_priv *ksz;
 };

 static int dm_ksz_mdio_read(struct udevice *dev, int addr, int devad, int reg)
 {
 	struct ksz_mdio_priv *priv = dev_get_priv(dev);
 	struct ksz_dsa_priv *ksz = priv->ksz;
 	u16 val = 0xffff;

 	ksz_pread16(ksz->dev, addr, 0x100 + (reg << 1), &val);
 	dev_dbg(ksz->dev, "%s P%d reg=0x%04x:0x%04x<<0x%04x\n", __func__,
 		addr + 1, reg, 0x100 + (reg << 1), val);

 	return val;
 };

 static int dm_ksz_mdio_write(struct udevice *dev, int addr, int devad, int reg, u16 val)
 {
 	struct ksz_mdio_priv *priv = dev_get_priv(dev);
 	struct ksz_dsa_priv *ksz = priv->ksz;

 	dev_dbg(ksz->dev, "%s P%d reg=0x%04x:%04x>>0x%04x\n",
 		__func__, addr + 1, reg, 0x100 + (reg << 1), val);
 	ksz_pwrite16(ksz->dev, addr, 0x100 + (reg << 1), val);

 	return 0;
 }

 static const struct mdio_ops ksz_mdio_ops = {
 	.read = dm_ksz_mdio_read,
 	.write = dm_ksz_mdio_write,
 };

 static int ksz_mdio_bind(struct udevice *dev)
 {
 	char name[16];
 	static int num_devices;

 	dev_dbg(dev, "%s\n", __func__);
 	sprintf(name, "ksz-mdio-%d", num_devices++);
 	device_set_name(dev, name);

 	return 0;
 }

 static int ksz_mdio_probe(struct udevice *dev)
 {
 	struct ksz_mdio_priv *priv = dev_get_priv(dev);

 	dev_dbg(dev, "%s\n", __func__);
 	priv->ksz = dev_get_parent_priv(dev->parent);

 	return 0;
 }

 static const struct udevice_id ksz_mdio_ids[] = {
 	{ .compatible = "microchip,ksz-mdio" },
 	{ }
 };

 U_BOOT_DRIVER(ksz_mdio) = {
 	.name		= KSZ_MDIO_CHILD_DRV_NAME,
 	.id		= UCLASS_MDIO,
 	.of_match	= ksz_mdio_ids,
 	.bind		= ksz_mdio_bind,
 	.probe		= ksz_mdio_probe,
 	.ops		= &ksz_mdio_ops,
 	.priv_auto	= sizeof(struct ksz_mdio_priv),
 	.plat_auto	= sizeof(struct mdio_perdev_priv),
 };

 static int ksz_port_setup(struct udevice *dev, int port,
 			  phy_interface_t interface)
 {
 	struct dsa_pdata *pdata = dev_get_uclass_plat(dev);
 	u8 data8;

 	dev_dbg(dev, "%s P%d %s\n", __func__, port + 1,
 		(port == pdata->cpu_port) ? "cpu" : "");

 	if (port != pdata->cpu_port) {
 		/* phy port: config errata and leds */
 		ksz_phy_errata_setup(dev, port);
 	} else {
 		/* cpu port: configure MAC interface mode */
 		ksz_pread8(dev, port, REG_PORT_XMII_CTRL_1, &data8);
 		dev_dbg(dev, "%s P%d cpu interface %s\n", __func__, port + 1,
 			phy_string_for_interface(interface));
 		switch (interface) {
 		case PHY_INTERFACE_MODE_MII:
 			data8 &= ~PORT_MII_SEL_M;
 			data8 |= PORT_MII_SEL;
 			data8 |= PORT_MII_NOT_1GBIT;
 			break;
 		case PHY_INTERFACE_MODE_RMII:
 			data8 &= ~PORT_MII_SEL_M;
 			data8 |= PORT_RMII_SEL;
 			data8 |= PORT_MII_NOT_1GBIT;
 			break;
 		case PHY_INTERFACE_MODE_GMII:
 			data8 &= ~PORT_MII_SEL_M;
 			data8 |= PORT_GMII_SEL;
 			data8 &= ~PORT_MII_NOT_1GBIT;
 			break;
 		default:
 			data8 &= ~PORT_MII_SEL_M;
 			data8 |= PORT_RGMII_SEL;
 			data8 &= ~PORT_MII_NOT_1GBIT;
 			data8 &= ~PORT_RGMII_ID_IG_ENABLE;
 			data8 &= ~PORT_RGMII_ID_EG_ENABLE;
 			if (interface == PHY_INTERFACE_MODE_RGMII_ID ||
 			    interface == PHY_INTERFACE_MODE_RGMII_RXID)
 				data8 |= PORT_RGMII_ID_IG_ENABLE;
 			if (interface == PHY_INTERFACE_MODE_RGMII_ID ||
 			    interface == PHY_INTERFACE_MODE_RGMII_TXID)
 				data8 |= PORT_RGMII_ID_EG_ENABLE;
 			break;
 		}
 		ksz_write8(dev, PORT_CTRL_ADDR(port, REG_PORT_XMII_CTRL_1), data8);
 	}

 	return 0;
 }

 static int ksz_port_enable(struct udevice *dev, int port, struct phy_device *phy)
 {
 	struct dsa_pdata *pdata = dev_get_uclass_plat(dev);
 	struct ksz_dsa_priv *priv = dev_get_priv(dev);
 	int supported = PHY_GBIT_FEATURES;
 	u8 data8;
 	int ret;

 	dev_dbg(dev, "%s P%d 0x%x %s\n", __func__, port + 1, phy->phy_id,
 		phy_string_for_interface(phy->interface));

 	/* setup this port */
 	ret = ksz_port_setup(dev, port, phy->interface);
 	if (ret) {
 		dev_err(dev, "port setup failed: %d\n", ret);
 		return ret;
 	}

 	/* enable port forwarding for this port */
 	ksz_pread8(priv->dev, port, REG_PORT_MSTP_STATE, &data8);
 	data8 &= ~(PORT_TX_ENABLE | PORT_RX_ENABLE | PORT_LEARN_DISABLE);
 	data8 |= (PORT_TX_ENABLE | PORT_RX_ENABLE);
 	ksz_pwrite8(priv->dev, port, REG_PORT_MSTP_STATE, data8);

 	/* if cpu master we are done */
 	if (port == pdata->cpu_port)
 		return 0;

 	/* configure phy */
 	phy->supported &= supported;
 	phy->advertising &= supported;
 	ret = phy_config(phy);
 	if (ret)
 		return ret;

 	ret = phy_startup(phy);
 	if (ret)
 		return ret;

 	/* start switch */
 	ksz_read8(priv->dev, REG_SW_OPERATION, &data8);
 	data8 |= SW_START;
 	ksz_write8(priv->dev, REG_SW_OPERATION, data8);

 	/* keep track of current enabled non-cpu port */
 	priv->active_port = port;

 	return 0;
 }

 static void ksz_port_disable(struct udevice *dev, int port, struct phy_device *phy)
 {
 	struct dsa_pdata *pdata = dev_get_uclass_plat(dev);
 	struct ksz_dsa_priv *priv = dev_get_priv(dev);
 	u8 data8;

 	dev_dbg(dev, "%s P%d 0x%x\n", __func__, port + 1, phy->phy_id);

 	/* can't disable CPU port without re-configuring/re-starting switch */
 	if (port == pdata->cpu_port)
 		return;

 	/* disable port */
 	ksz_pread8(priv->dev, port, REG_PORT_MSTP_STATE, &data8);
 	data8 &= ~(PORT_TX_ENABLE | PORT_RX_ENABLE | PORT_LEARN_DISABLE);
 	data8 |= PORT_LEARN_DISABLE;
 	ksz_pwrite8(priv->dev, port, REG_PORT_MSTP_STATE, data8);

 	/*
 	 * we don't call phy_shutdown here to avoid waiting next time we use
 	 * the port, but the downside is that remote side will think we're
 	 * actively processing traffic although we are not.
 	 */
 }

 static int ksz_xmit(struct udevice *dev, int port, void *packet, int length)
 {
 	dev_dbg(dev, "%s P%d %d\n", __func__, port + 1, length);

 	return 0;
 }

 static int ksz_recv(struct udevice *dev, int *port, void *packet, int length)
 {
 	struct ksz_dsa_priv *priv = dev_get_priv(dev);

 	dev_dbg(dev, "%s P%d %d\n", __func__, priv->active_port + 1, length);
 	*port = priv->active_port;

 	return 0;
 };

 static const struct dsa_ops ksz_dsa_ops = {
 	.port_enable = ksz_port_enable,
 	.port_disable = ksz_port_disable,
 	.xmit = ksz_xmit,
 	.rcv = ksz_recv,
 };

 static int ksz_probe_mdio(struct udevice *dev)
 {
 	ofnode node, mdios;
 	int ret;

 	mdios = dev_read_subnode(dev, "mdios");
 	if (ofnode_valid(mdios)) {
 		ofnode_for_each_subnode(node, mdios) {
 			const char *name = ofnode_get_name(node);
 			struct udevice *pdev;

 			ret = device_bind_driver_to_node(dev,
 							 KSZ_MDIO_CHILD_DRV_NAME,
 							 name, node, &pdev);
 			if (ret)
 				dev_err(dev, "failed to probe %s: %d\n", name, ret);
 		}
 	}

 	return 0;
 }

 /*
  * I2C driver
  */
 static int ksz_i2c_probe(struct udevice *dev)
 {
 	struct dsa_pdata *pdata = dev_get_uclass_plat(dev);
 	struct ksz_dsa_priv *priv = dev_get_priv(dev);
 	struct udevice *master = dsa_get_master(dev);
 	int i, ret;
 	u8 data8;
 	u32 id;

 	if (!master)
 		return -ENODEV;

 	dev_dbg(dev, "%s %s master:%s\n", __func__, dev->name, master->name);
 	dev_set_parent_priv(dev, priv);

 	ret = i2c_set_chip_offset_len(dev, 2);
 	if (ret) {
 		printf("i2c_set_chip_offset_len failed: %d\n", ret);
 		return ret;
 	}

 	/* default config */
 	priv->dev = dev;

 	/* chip level reset */
 	ksz_read8(priv->dev, REG_SW_OPERATION, &data8);
 	data8 |= SW_RESET;
 	ksz_write8(priv->dev, REG_SW_OPERATION, data8);

 	/* read chip id */
 	ret = ksz_read32(dev, REG_CHIP_ID0__1, &id);
 	if (ret)
 		return ret;
 	id = __swab32(id);
 	dev_dbg(dev, "%s id=0x%08x\n", __func__, id);
 	switch (id & 0xffffff00) {
 	case 0x00947700:
 		puts("KSZ9477S: ");
 		break;
 	case 0x00956700:
 		puts("KSZ9567R: ");
 		break;
 	case 0x00989700:
 		puts("KSZ9897S: ");
 		break;
 	default:
 		dev_err(dev, "invalid chip id: 0x%08x\n", id);
 		return -EINVAL;
 	}

 	/* probe mdio bus */
 	ret = ksz_probe_mdio(dev);
 	if (ret)
 		return ret;

 	/* disable ports by default */
 	for (i = 0; i < pdata->num_ports; i++) {
 		ksz_pread8(priv->dev, i, REG_PORT_MSTP_STATE, &data8);
 		data8 &= ~(PORT_TX_ENABLE | PORT_RX_ENABLE | PORT_LEARN_DISABLE);
 		ksz_pwrite8(priv->dev, i, REG_PORT_MSTP_STATE, data8);
 	}

 	dsa_set_tagging(dev, 0, 0);

 	return 0;
 };

 static const struct udevice_id ksz_i2c_ids[] = {
 	{ .compatible = "microchip,ksz9897" },
 	{ .compatible = "microchip,ksz9477" },
 	{ .compatible = "microchip,ksz9567" },
 	{ }
 };

 U_BOOT_DRIVER(ksz) = {
 	.name		= "ksz-switch",
 	.id		= UCLASS_DSA,
 	.of_match	= ksz_i2c_ids,
 	.probe		= ksz_i2c_probe,
 	.ops		= &ksz_dsa_ops,
 	.priv_auto	= sizeof(struct ksz_dsa_priv),
 };
	// SPDX-License-Identifier: GPL-2.0+
	/*
	* (C) Copyright 2020
	* Tim Harvey, Gateworks Corporation
	*/

	#include <dm.h>
	#include <dm/device_compat.h>
	#include <dm/device-internal.h>
	#include <dm/lists.h>
	#include <eth_phy.h>
	#include <linux/delay.h>
	#include <miiphy.h>
	#include <i2c.h>
	#include <net/dsa.h>

	#include <asm-generic/gpio.h>

	/* Global registers */

	/* Chip ID */
	#define REG_CHIP_ID0__1 0x0000

	/* Operation control */
	#define REG_SW_OPERATION 0x0300
	#define SW_RESET BIT(1)
	#define SW_START BIT(0)

	/* Port Specific Registers */
	#define PORT_CTRL_ADDR(port, addr) ((addr) \| (((port) + 1) << 12))

	/* Port Control */
	#define REG_PORT_XMII_CTRL_1 0x0301
	#define PORT_MII_NOT_1GBIT BIT(6)
	#define PORT_MII_SEL_EDGE BIT(5)
	#define PORT_RGMII_ID_IG_ENABLE BIT(4)
	#define PORT_RGMII_ID_EG_ENABLE BIT(3)
	#define PORT_MII_MAC_MODE BIT(2)
	#define PORT_MII_SEL_M 0x3
	#define PORT_RGMII_SEL 0x0
	#define PORT_RMII_SEL 0x1
	#define PORT_GMII_SEL 0x2
	#define PORT_MII_SEL 0x3

	/* Port MSTP State Register */
	#define REG_PORT_MSTP_STATE 0x0b04
	#define PORT_TX_ENABLE BIT(2)
	#define PORT_RX_ENABLE BIT(1)
	#define PORT_LEARN_DISABLE BIT(0)

	/* MMD */
	#define REG_PORT_PHY_MMD_SETUP 0x011A
	#define PORT_MMD_OP_MODE_M 0x3
	#define PORT_MMD_OP_MODE_S 14
	#define PORT_MMD_OP_INDEX 0
	#define PORT_MMD_OP_DATA_NO_INCR 1
	#define PORT_MMD_OP_DATA_INCR_RW 2
	#define PORT_MMD_OP_DATA_INCR_W 3
	#define PORT_MMD_DEVICE_ID_M 0x1F
	#define MMD_SETUP(mode, dev) (((u16)(mode) << PORT_MMD_OP_MODE_S) \| (dev))
	#define REG_PORT_PHY_MMD_INDEX_DATA 0x011C

	struct ksz_dsa_priv {
	struct udevice *dev;
	int active_port;
	};

	static inline int ksz_read8(struct udevice dev, u32 reg, u8 val)
	{
	int ret = dm_i2c_read(dev, reg, val, 1);

	dev_dbg(dev, "%s 0x%04x<<0x%02x\n", __func__, reg, *val);

	return ret;
	}

	static inline int ksz_pread8(struct udevice dev, int port, int reg, u8 val)
	{
	return ksz_read8(dev, PORT_CTRL_ADDR(port, reg), val);
	}

	static inline int ksz_write8(struct udevice *dev, u32 reg, u8 val)
	{
	dev_dbg(dev, "%s 0x%04x>>0x%02x\n", __func__, reg, val);
	return dm_i2c_write(dev, reg, &val, 1);
	}

	static inline int ksz_pwrite8(struct udevice *dev, int port, int reg, u8 val)
	{
	return ksz_write8(dev, PORT_CTRL_ADDR(port, reg), val);
	}

	static inline int ksz_write16(struct udevice *dev, u32 reg, u16 val)
	{
	u8 buf[2];

	buf[1] = val & 0xff;
	buf[0] = val >> 8;
	dev_dbg(dev, "%s 0x%04x>>0x%04x\n", __func__, reg, val);

	return dm_i2c_write(dev, reg, buf, 2);
	}

	static inline int ksz_pwrite16(struct udevice *dev, int port, int reg, u16 val)
	{
	return ksz_write16(dev, PORT_CTRL_ADDR(port, reg), val);
	}

	static inline int ksz_read16(struct udevice dev, u32 reg, u16 val)
	{
	u8 buf[2];
	int ret;

	ret = dm_i2c_read(dev, reg, buf, 2);
	*val = (buf[0] << 8) \| buf[1];
	dev_dbg(dev, "%s 0x%04x<<0x%04x\n", __func__, reg, *val);

	return ret;
	}

	static inline int ksz_pread16(struct udevice dev, int port, int reg, u16 val)
	{
	return ksz_read16(dev, PORT_CTRL_ADDR(port, reg), val);
	}

	static inline int ksz_read32(struct udevice dev, u32 reg, u32 val)
	{
	return dm_i2c_read(dev, reg, (u8 *)val, 4);
	}

	static inline int ksz_pread32(struct udevice dev, int port, int reg, u32 val)
	{
	return ksz_read32(dev, PORT_CTRL_ADDR(port, reg), val);
	}

	static inline int ksz_write32(struct udevice *dev, u32 reg, u32 val)
	{
	u8 buf[4];

	buf[3] = val & 0xff;
	buf[2] = (val >> 24) & 0xff;
	buf[1] = (val >> 16) & 0xff;
	buf[0] = (val >> 8) & 0xff;
	dev_dbg(dev, "%s 0x%04x>>0x%04x\n", __func__, reg, val);

	return dm_i2c_write(dev, reg, buf, 4);
	}

	static inline int ksz_pwrite32(struct udevice *dev, int port, int reg, u32 val)
	{
	return ksz_write32(dev, PORT_CTRL_ADDR(port, reg), val);
	}

	static __maybe_unused void ksz_port_mmd_read(struct udevice *dev, int port,
	u8 addr, u16 reg, u16 *val)
	{
	ksz_pwrite16(dev, port, REG_PORT_PHY_MMD_SETUP, MMD_SETUP(PORT_MMD_OP_INDEX, addr));
	ksz_pwrite16(dev, port, REG_PORT_PHY_MMD_INDEX_DATA, reg);
	ksz_pwrite16(dev, port, REG_PORT_PHY_MMD_SETUP, MMD_SETUP(PORT_MMD_OP_DATA_NO_INCR, addr));
	ksz_pread16(dev, port, REG_PORT_PHY_MMD_INDEX_DATA, val);
	dev_dbg(dev, "%s P%d 0x%02x:0x%04x<<0x%04x\n", __func__, port + 1, addr, reg, *val);
	}

	static void ksz_port_mmd_write(struct udevice *dev, int port, u8 addr, u16 reg, u16 val)
	{
	dev_dbg(dev, "%s P%d 0x%02x:0x%04x>>0x%04x\n", __func__, port + 1, addr, addr, val);
	ksz_pwrite16(dev, port, REG_PORT_PHY_MMD_SETUP, MMD_SETUP(PORT_MMD_OP_INDEX, addr));
	ksz_pwrite16(dev, port, REG_PORT_PHY_MMD_INDEX_DATA, addr);
	ksz_pwrite16(dev, port, REG_PORT_PHY_MMD_SETUP, MMD_SETUP(PORT_MMD_OP_DATA_NO_INCR, addr));
	ksz_pwrite16(dev, port, REG_PORT_PHY_MMD_INDEX_DATA, val);
	}

	/* Apply PHY settings to address errata listed in KSZ9477, KSZ9897, KSZ9896, KSZ9567
	* Silicon Errata and Data Sheet Clarification documents
	*/
	static void ksz_phy_errata_setup(struct udevice *dev, int port)
	{
	dev_dbg(dev, "%s P%d\n", __func__, port + 1);

	/* Register settings are needed to improve PHY receive performance */
	ksz_port_mmd_write(dev, port, 0x01, 0x6f, 0xdd0b);
	ksz_port_mmd_write(dev, port, 0x01, 0x8f, 0x6032);
	ksz_port_mmd_write(dev, port, 0x01, 0x9d, 0x248c);
	ksz_port_mmd_write(dev, port, 0x01, 0x75, 0x0060);
	ksz_port_mmd_write(dev, port, 0x01, 0xd3, 0x7777);
	ksz_port_mmd_write(dev, port, 0x1c, 0x06, 0x3008);
	ksz_port_mmd_write(dev, port, 0x1c, 0x08, 0x2001);

	/* Transmit waveform amplitude can be improved (1000BASE-T, 100BASE-TX, 10BASE-Te) */
	ksz_port_mmd_write(dev, port, 0x1c, 0x04, 0x00d0);

	/* Energy Efficient Ethernet (EEE) feature select must be manually disabled */
	ksz_port_mmd_write(dev, port, 0x07, 0x3c, 0x0000);

	/* Register settings are required to meet data sheet supply current specifications */
	ksz_port_mmd_write(dev, port, 0x1c, 0x13, 0x6eff);
	ksz_port_mmd_write(dev, port, 0x1c, 0x14, 0xe6ff);
	ksz_port_mmd_write(dev, port, 0x1c, 0x15, 0x6eff);
	ksz_port_mmd_write(dev, port, 0x1c, 0x16, 0xe6ff);
	ksz_port_mmd_write(dev, port, 0x1c, 0x17, 0x00ff);
	ksz_port_mmd_write(dev, port, 0x1c, 0x18, 0x43ff);
	ksz_port_mmd_write(dev, port, 0x1c, 0x19, 0xc3ff);
	ksz_port_mmd_write(dev, port, 0x1c, 0x1a, 0x6fff);
	ksz_port_mmd_write(dev, port, 0x1c, 0x1b, 0x07ff);
	ksz_port_mmd_write(dev, port, 0x1c, 0x1c, 0x0fff);
	ksz_port_mmd_write(dev, port, 0x1c, 0x1d, 0xe7ff);
	ksz_port_mmd_write(dev, port, 0x1c, 0x1e, 0xefff);
	ksz_port_mmd_write(dev, port, 0x1c, 0x20, 0xeeee);
	}

	/*
	* mii bus driver
	*/
	#define KSZ_MDIO_CHILD_DRV_NAME "ksz_mdio"

	struct ksz_mdio_priv {
	struct ksz_dsa_priv *ksz;
	};

	static int dm_ksz_mdio_read(struct udevice *dev, int addr, int devad, int reg)
	{
	struct ksz_mdio_priv *priv = dev_get_priv(dev);
	struct ksz_dsa_priv *ksz = priv->ksz;
	u16 val = 0xffff;

	ksz_pread16(ksz->dev, addr, 0x100 + (reg << 1), &val);
	dev_dbg(ksz->dev, "%s P%d reg=0x%04x:0x%04x<<0x%04x\n", __func__,
	addr + 1, reg, 0x100 + (reg << 1), val);

	return val;
	};

	static int dm_ksz_mdio_write(struct udevice *dev, int addr, int devad, int reg, u16 val)
	{
	struct ksz_mdio_priv *priv = dev_get_priv(dev);
	struct ksz_dsa_priv *ksz = priv->ksz;

	dev_dbg(ksz->dev, "%s P%d reg=0x%04x:%04x>>0x%04x\n",
	__func__, addr + 1, reg, 0x100 + (reg << 1), val);
	ksz_pwrite16(ksz->dev, addr, 0x100 + (reg << 1), val);

	return 0;
	}

	static const struct mdio_ops ksz_mdio_ops = {
	.read = dm_ksz_mdio_read,
	.write = dm_ksz_mdio_write,
	};

	static int ksz_mdio_bind(struct udevice *dev)
	{
	char name[16];
	static int num_devices;

	dev_dbg(dev, "%s\n", __func__);
	sprintf(name, "ksz-mdio-%d", num_devices++);
	device_set_name(dev, name);

	return 0;
	}

	static int ksz_mdio_probe(struct udevice *dev)
	{
	struct ksz_mdio_priv *priv = dev_get_priv(dev);

	dev_dbg(dev, "%s\n", __func__);
	priv->ksz = dev_get_parent_priv(dev->parent);

	return 0;
	}

	static const struct udevice_id ksz_mdio_ids[] = {
	{ .compatible = "microchip,ksz-mdio" },
	{ }
	};

	U_BOOT_DRIVER(ksz_mdio) = {
	.name = KSZ_MDIO_CHILD_DRV_NAME,
	.id = UCLASS_MDIO,
	.of_match = ksz_mdio_ids,
	.bind = ksz_mdio_bind,
	.probe = ksz_mdio_probe,
	.ops = &ksz_mdio_ops,
	.priv_auto = sizeof(struct ksz_mdio_priv),
	.plat_auto = sizeof(struct mdio_perdev_priv),
	};

	static int ksz_port_setup(struct udevice *dev, int port,
	phy_interface_t interface)
	{
	struct dsa_pdata *pdata = dev_get_uclass_plat(dev);
	u8 data8;

	dev_dbg(dev, "%s P%d %s\n", __func__, port + 1,
	(port == pdata->cpu_port) ? "cpu" : "");

	if (port != pdata->cpu_port) {
	/* phy port: config errata and leds */
	ksz_phy_errata_setup(dev, port);
	} else {
	/* cpu port: configure MAC interface mode */
	ksz_pread8(dev, port, REG_PORT_XMII_CTRL_1, &data8);
	dev_dbg(dev, "%s P%d cpu interface %s\n", __func__, port + 1,
	phy_string_for_interface(interface));
	switch (interface) {
	case PHY_INTERFACE_MODE_MII:
	data8 &= ~PORT_MII_SEL_M;
	data8 \|= PORT_MII_SEL;
	data8 \|= PORT_MII_NOT_1GBIT;
	break;
	case PHY_INTERFACE_MODE_RMII:
	data8 &= ~PORT_MII_SEL_M;
	data8 \|= PORT_RMII_SEL;
	data8 \|= PORT_MII_NOT_1GBIT;
	break;
	case PHY_INTERFACE_MODE_GMII:
	data8 &= ~PORT_MII_SEL_M;
	data8 \|= PORT_GMII_SEL;
	data8 &= ~PORT_MII_NOT_1GBIT;
	break;
	default:
	data8 &= ~PORT_MII_SEL_M;
	data8 \|= PORT_RGMII_SEL;
	data8 &= ~PORT_MII_NOT_1GBIT;
	data8 &= ~PORT_RGMII_ID_IG_ENABLE;
	data8 &= ~PORT_RGMII_ID_EG_ENABLE;
	if (interface == PHY_INTERFACE_MODE_RGMII_ID \|\|
	interface == PHY_INTERFACE_MODE_RGMII_RXID)
	data8 \|= PORT_RGMII_ID_IG_ENABLE;
	if (interface == PHY_INTERFACE_MODE_RGMII_ID \|\|
	interface == PHY_INTERFACE_MODE_RGMII_TXID)
	data8 \|= PORT_RGMII_ID_EG_ENABLE;
	break;
	}
	ksz_write8(dev, PORT_CTRL_ADDR(port, REG_PORT_XMII_CTRL_1), data8);
	}

	return 0;
	}

	static int ksz_port_enable(struct udevice dev, int port, struct phy_device phy)
	{
	struct dsa_pdata *pdata = dev_get_uclass_plat(dev);
	struct ksz_dsa_priv *priv = dev_get_priv(dev);
	int supported = PHY_GBIT_FEATURES;
	u8 data8;
	int ret;

	dev_dbg(dev, "%s P%d 0x%x %s\n", __func__, port + 1, phy->phy_id,
	phy_string_for_interface(phy->interface));

	/* setup this port */
	ret = ksz_port_setup(dev, port, phy->interface);
	if (ret) {
	dev_err(dev, "port setup failed: %d\n", ret);
	return ret;
	}

	/* enable port forwarding for this port */
	ksz_pread8(priv->dev, port, REG_PORT_MSTP_STATE, &data8);
	data8 &= ~(PORT_TX_ENABLE \| PORT_RX_ENABLE \| PORT_LEARN_DISABLE);
	data8 \|= (PORT_TX_ENABLE \| PORT_RX_ENABLE);
	ksz_pwrite8(priv->dev, port, REG_PORT_MSTP_STATE, data8);

	/* if cpu master we are done */
	if (port == pdata->cpu_port)
	return 0;

	/* configure phy */
	phy->supported &= supported;
	phy->advertising &= supported;
	ret = phy_config(phy);
	if (ret)
	return ret;

	ret = phy_startup(phy);
	if (ret)
	return ret;

	/* start switch */
	ksz_read8(priv->dev, REG_SW_OPERATION, &data8);
	data8 \|= SW_START;
	ksz_write8(priv->dev, REG_SW_OPERATION, data8);

	/* keep track of current enabled non-cpu port */
	priv->active_port = port;

	return 0;
	}

	static void ksz_port_disable(struct udevice dev, int port, struct phy_device phy)
	{
	struct dsa_pdata *pdata = dev_get_uclass_plat(dev);
	struct ksz_dsa_priv *priv = dev_get_priv(dev);
	u8 data8;

	dev_dbg(dev, "%s P%d 0x%x\n", __func__, port + 1, phy->phy_id);

	/* can't disable CPU port without re-configuring/re-starting switch */
	if (port == pdata->cpu_port)
	return;

	/* disable port */
	ksz_pread8(priv->dev, port, REG_PORT_MSTP_STATE, &data8);
	data8 &= ~(PORT_TX_ENABLE \| PORT_RX_ENABLE \| PORT_LEARN_DISABLE);
	data8 \|= PORT_LEARN_DISABLE;
	ksz_pwrite8(priv->dev, port, REG_PORT_MSTP_STATE, data8);

	/*
	* we don't call phy_shutdown here to avoid waiting next time we use
	* the port, but the downside is that remote side will think we're
	* actively processing traffic although we are not.
	*/
	}

	static int ksz_xmit(struct udevice dev, int port, void packet, int length)
	{
	dev_dbg(dev, "%s P%d %d\n", __func__, port + 1, length);

	return 0;
	}

	static int ksz_recv(struct udevice dev, int port, void *packet, int length)
	{
	struct ksz_dsa_priv *priv = dev_get_priv(dev);

	dev_dbg(dev, "%s P%d %d\n", __func__, priv->active_port + 1, length);
	*port = priv->active_port;

	return 0;
	};

	static const struct dsa_ops ksz_dsa_ops = {
	.port_enable = ksz_port_enable,
	.port_disable = ksz_port_disable,
	.xmit = ksz_xmit,
	.rcv = ksz_recv,
	};

	static int ksz_probe_mdio(struct udevice *dev)
	{
	ofnode node, mdios;
	int ret;

	mdios = dev_read_subnode(dev, "mdios");
	if (ofnode_valid(mdios)) {
	ofnode_for_each_subnode(node, mdios) {
	const char *name = ofnode_get_name(node);
	struct udevice *pdev;

	ret = device_bind_driver_to_node(dev,
	KSZ_MDIO_CHILD_DRV_NAME,
	name, node, &pdev);
	if (ret)
	dev_err(dev, "failed to probe %s: %d\n", name, ret);
	}
	}

	return 0;
	}

	/*
	* I2C driver
	*/
	static int ksz_i2c_probe(struct udevice *dev)
	{
	struct dsa_pdata *pdata = dev_get_uclass_plat(dev);
	struct ksz_dsa_priv *priv = dev_get_priv(dev);
	struct udevice *master = dsa_get_master(dev);
	int i, ret;
	u8 data8;
	u32 id;

	if (!master)
	return -ENODEV;

	dev_dbg(dev, "%s %s master:%s\n", __func__, dev->name, master->name);
	dev_set_parent_priv(dev, priv);

	ret = i2c_set_chip_offset_len(dev, 2);
	if (ret) {
	printf("i2c_set_chip_offset_len failed: %d\n", ret);
	return ret;
	}

	/* default config */
	priv->dev = dev;

	/* chip level reset */
	ksz_read8(priv->dev, REG_SW_OPERATION, &data8);
	data8 \|= SW_RESET;
	ksz_write8(priv->dev, REG_SW_OPERATION, data8);

	/* read chip id */
	ret = ksz_read32(dev, REG_CHIP_ID0__1, &id);
	if (ret)
	return ret;
	id = __swab32(id);
	dev_dbg(dev, "%s id=0x%08x\n", __func__, id);
	switch (id & 0xffffff00) {
	case 0x00947700:
	puts("KSZ9477S: ");
	break;
	case 0x00956700:
	puts("KSZ9567R: ");
	break;
	case 0x00989700:
	puts("KSZ9897S: ");
	break;
	default:
	dev_err(dev, "invalid chip id: 0x%08x\n", id);
	return -EINVAL;
	}

	/* probe mdio bus */
	ret = ksz_probe_mdio(dev);
	if (ret)
	return ret;

	/* disable ports by default */
	for (i = 0; i < pdata->num_ports; i++) {
	ksz_pread8(priv->dev, i, REG_PORT_MSTP_STATE, &data8);
	data8 &= ~(PORT_TX_ENABLE \| PORT_RX_ENABLE \| PORT_LEARN_DISABLE);
	ksz_pwrite8(priv->dev, i, REG_PORT_MSTP_STATE, data8);
	}

	dsa_set_tagging(dev, 0, 0);

	return 0;
	};

	static const struct udevice_id ksz_i2c_ids[] = {
	{ .compatible = "microchip,ksz9897" },
	{ .compatible = "microchip,ksz9477" },
	{ .compatible = "microchip,ksz9567" },
	{ }
	};

	U_BOOT_DRIVER(ksz) = {
	.name = "ksz-switch",
	.id = UCLASS_DSA,
	.of_match = ksz_i2c_ids,
	.probe = ksz_i2c_probe,
	.ops = &ksz_dsa_ops,
	.priv_auto = sizeof(struct ksz_dsa_priv),
	};