blob: e76ca73d4730727d3235231985f54c86666b0984 [file] [log] [blame]
/*
* Copyright 2011 Alex Dubov <oakad@yahoo.com>
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* Merury Computers MPQ101 board configuration file
*
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#ifdef CONFIG_36BIT
# define CONFIG_PHYS_64BIT
#endif
/* High Level Configuration Options */
#define CONFIG_BOOKE /* BOOKE */
#define CONFIG_E500 /* BOOKE e500 family */
#define CONFIG_MPC85xx /* MPC8540/60/55/41/48 */
#define CONFIG_MPC8548 /* MPC8548 specific */
#define CONFIG_MPQ101 /* MPQ101 board specific */
#define CONFIG_SYS_SRIO /* enable serial RapidIO */
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
#define CONFIG_FSL_LAW /* Use common FSL init code */
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_L2_CACHE /* toggle L2 cache */
#define CONFIG_BTB /* toggle branch predition */
#define CONFIG_PANIC_HANG
/*
* Only possible on E500 Version 2 or newer cores.
*/
#define CONFIG_ENABLE_36BIT_PHYS
#ifdef CONFIG_PHYS_64BIT
# define CONFIG_ADDR_MAP
# define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
#endif
#define CONFIG_SYS_CLK_FREQ 33000000 /* sysclk for MPC85xx */
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#define CONFIG_SYS_CCSRBAR 0xe0000000
#ifdef CONFIG_PHYS_64BIT
# define CONFIG_SYS_CCSRBAR_PHYS 0xfe0000000ull
#else
# define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR
#endif
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR
/* DDR Setup */
#define CONFIG_FSL_DDR2
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_NUM_DDR_CONTROLLERS 1
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
/* Fixed 512MB DDR2 parameters */
#define CONFIG_SYS_SDRAM_SIZE_LOG 29 /* DDR is 512MB */
#define CONFIG_SYS_DDR_CS0_BNDS 0x0000001f
#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014102
#define CONFIG_SYS_DDR_TIMING_3 0x00010000
#define CONFIG_SYS_DDR_TIMING_0 0x00260802
#define CONFIG_SYS_DDR_TIMING_1 0x5c47a432
#define CONFIG_SYS_DDR_TIMING_1_PERF 0x49352322
#define CONFIG_SYS_DDR_TIMING_2 0x03984cce
#define CONFIG_SYS_DDR_TIMING_2_PERF 0x14904cca
#define CONFIG_SYS_DDR_MODE_1 0x00400442
#define CONFIG_SYS_DDR_MODE_1_PERF 0x00480432
#define CONFIG_SYS_DDR_MODE_2 0x00000000
#define CONFIG_SYS_DDR_MODE_2_PERF 0x00000000
#define CONFIG_SYS_DDR_INTERVAL 0x08200100
#define CONFIG_SYS_DDR_INTERVAL_PERF 0x06180100
#define CONFIG_SYS_DDR_CLK_CTRL 0x03800000
#define CONFIG_SYS_DDR_CONTROL 0xc3008000 /* Type = DDR2 */
#define CONFIG_SYS_DDR_CONTROL2 0x04400000
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_SYS_MEMTEST_START 0x0ff00000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0ffffffc
/*
* RAM definitions
*/
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \
- GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
/*
* Local Bus Definitions
*/
#define CONFIG_SYS_LBC_LCRR 0x00000004 /* LB clock ratio reg */
#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */
/*
* FLASH on the Local Bus
* One bank, 128M, using the CFI driver.
*/
#define CONFIG_SYS_BOOT_BLOCK 0xf8000000 /* boot TLB block */
#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_BOOT_BLOCK /* start of FLASH 128M */
#ifdef CONFIG_PHYS_64BIT
# define CONFIG_SYS_FLASH_BASE_PHYS 0xff8000000ull
#else
# define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
#endif
/* 0xf8001801 */
#define CONFIG_SYS_BR0_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
| BR_PS_32 | BR_V)
/* 0xf8006ff7 */
#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(128) | OR_GPCM_XAM | OR_GPCM_CSNT \
| OR_GPCM_ACS_DIV2 | OR_GPCM_XACS \
| OR_GPCM_SCY_15 | OR_GPCM_TRLX \
| OR_GPCM_EHTR | OR_GPCM_EAD)
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
/*
* When initializing flash, if we cannot find the manufacturer ID,
* assume this is the AMD flash.
*/
#define CONFIG_ASSUME_AMD_FLASH
/*
* Environment parameters
*/
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SYS_USE_PPCENV
#define ENV_IS_EMBEDDED
#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K */
#define CONFIG_ENV_SIZE 0x800
/* Environment at the start of flash sector, before text. */
#define CONFIG_ENV_ADDR (CONFIG_SYS_TEXT_BASE - CONFIG_ENV_SIZE)
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#define CONFIG_SYS_TEXT_BASE 0xfffc0800
#define CONFIG_SYS_LDSCRIPT "board/mercury/mpq101/u-boot.lds"
/*
* Cypress CY7C67200 USB controller on the Local Bus.
* Not supported by u-boot at present.
*/
#define CONFIG_SYS_LBC_OPTION_BASE 0xf0000000
#ifdef CONFIG_PHYS_64BIT
# define CONFIG_SYS_LBC_OPTION_BASE_PHYS 0xff0000000ull
#else
# define CONFIG_SYS_LBC_OPTION_BASE_PHYS CONFIG_SYS_LBC_OPTION_BASE
#endif
/* 0xf0001001 */
#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_LBC_OPTION_BASE_PHYS) \
| BR_PS_16 | BR_V)
/* fffff002 */
#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(0x8000) | OR_GPCM_XAM \
| OR_GPCM_BCTLD | OR_GPCM_EHTR)
/*
* Serial Ports
*/
#define CONFIG_CONS_INDEX 2
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_BAUDRATE_TABLE {300, 600, 1200, 2400, 4800, 9600, \
19200, 38400, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
/*
* I2C buses and peripherals
*/
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support*/
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE 0x7f
#define CONFIG_SYS_I2C_OFFSET 0x3000
#define CONFIG_SYS_I2C2_OFFSET 0x3100
/* I2C RTC - M41T81 */
#define CONFIG_RTC_M41T62
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#define CONFIG_SYS_M41T11_BASE_YEAR 2000
/* I2C EEPROM - 24C256 */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 12
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_EEPROM_BUS_NUM 1
/*
* RapidIO MMU
*/
#ifdef CONFIG_SYS_SRIO
# define CONFIG_SRIO1
# define CONFIG_SYS_SRIO1_MEM_VIRT 0xc0000000
# define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */
# ifdef CONFIG_PHYS_64BIT
# define CONFIG_SYS_SRIO1_MEM_PHYS 0xfc0000000ull
# else
# define CONFIG_SYS_SRIO1_MEM_PHYS CONFIG_SYS_SRIO1_MEM_VIRT
# endif
#endif
/*
* Ethernet
*/
#ifdef CONFIG_TSEC_ENET
# ifndef CONFIG_NET_MULTI
# define CONFIG_NET_MULTI
# endif
# define CONFIG_MII /* MII PHY management */
# define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
# define CONFIG_TSEC1
# define CONFIG_TSEC1_NAME "eTSEC0"
# define TSEC1_PHY_ADDR 0x10
# define TSEC1_PHYIDX 0
# define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
# define CONFIG_TSEC2
# define CONFIG_TSEC2_NAME "eTSEC1"
# define TSEC2_PHY_ADDR 0x11
# define TSEC2_PHYIDX 0
# define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
# define CONFIG_TSEC3
# define CONFIG_TSEC3_NAME "eTSEC2"
# define TSEC3_PHY_ADDR 0x12
# define TSEC3_PHYIDX 0
# define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
# define CONFIG_TSEC4
# define CONFIG_TSEC4_NAME "eTSEC3"
# define TSEC4_PHY_ADDR 0x13
# define TSEC4_PHYIDX 0
# define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
/* Options are: eTSEC[0-3] */
# define CONFIG_ETHPRIME "eTSEC0"
# define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
#endif
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_PING
#define CONFIG_CMD_SNTP
#define CONFIG_CMD_I2C
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_MII
#define CONFIG_CMD_ELF
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_SETEXPR
#define CONFIG_CMD_JFFS2
/*
* Miscellaneous configurable options
*/
/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
#define CONFIG_OF_STDOUT_VIA_ALIAS
#define CONFIG_FIT /* new uImage format support */
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER
#ifdef CONFIG_SYS_HUSH_PARSER
# define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
#define CONFIG_LOADS_ECHO /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#define CONFIG_SYS_PROMPT "MPQ-101=> " /* Monitor Command Prompt */
/* Console I/O Buffer Size */
#ifdef CONFIG_CMD_KGDB
# define CONFIG_SYS_CBSIZE 1024
#else
# define CONFIG_SYS_CBSIZE 256
#endif
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 16 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
#ifdef CONFIG_CMD_KGDB
# define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
# define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
* Basic Environment Configuration
*/
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
/*default location for tftp and bootm*/
#define CONFIG_LOADADDR CONFIG_SYS_LOAD_ADDR
#endif /* __CONFIG_H */