src/mainboard/google/rex/variants/rex0/overridetree.cb - mirrors/cros/chromiumos/third_party/coreboot - Git at Google

 chip soc/intel/meteorlake

 	register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC0)"	# USB2_C0
 	register "usb2_ports[3]" = "USB2_PORT_TYPE_C(OC_SKIP)"	# USB2_C1
 	register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)"	# M.2 WWAN
 	register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)"	# M.2 Camera
 	register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)"	# DCI
 	register "usb2_ports[8]" = "USB2_PORT_MID(OC3)"		# Type-A Port A0
 	register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)"	# M.2 Bluetooth

 	register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC3)"	# USB3/2 Type A port A0
 	register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)"	# DCI

 	register "tcss_ports[0]" = "TCSS_PORT_DEFAULT(OC0)"
 	register "tcss_ports[2]" = "TCSS_PORT_DEFAULT(OC_SKIP)"

 	# Enable eDP in Port A
 	register "ddi_port_A_config" = "1"
 	# Enable HDMI in Port B
 	register "ddi_port_B_config" = "0"

 	# Enable Display Port Configuration
 	register "ddi_ports_config" = "{
 		[DDI_PORT_A] = DDI_ENABLE_HPD,
 		[DDI_PORT_B] = DDI_ENABLE_HPD | DDI_ENABLE_DDC,
 	}"

 	register "serial_io_gspi_mode" = "{
 		[PchSerialIoIndexGSPI0] = PchSerialIoDisabled,
 		[PchSerialIoIndexGSPI1] = PchSerialIoPci,
 		[PchSerialIoIndexGSPI2] = PchSerialIoDisabled,
 	}"

 	register "serial_io_i2c_mode" = "{
 		[PchSerialIoIndexI2C0] = PchSerialIoPci,
 		[PchSerialIoIndexI2C1] = PchSerialIoPci,
 		[PchSerialIoIndexI2C2] = PchSerialIoDisabled,
 		[PchSerialIoIndexI2C3] = PchSerialIoPci,
 		[PchSerialIoIndexI2C4] = PchSerialIoPci,
 		[PchSerialIoIndexI2C5] = PchSerialIoPci,
 	}"

 	# Intel Common SoC Config
 	#+-------------------+---------------------------+
 	#| Field             |  Value                    |
 	#+-------------------+---------------------------+
 	#| I2C0              | Audio and WFC             |
 	#| I2C1              | Touchscreen               |
 	#| I2C3              | Touchpad                  |
 	#| I2C4              | cr50 TPM. Early init is   |
 	#|                   | required to set up a BAR  |
 	#|                   | for TPM communication     |
 	#| I2C5              | UFC, SAR1, SAR2, HPS      |
 	#+-------------------+---------------------------+
 	register "common_soc_config" = "{
 		.i2c[0] = {
 			.speed = I2C_SPEED_FAST,
 			.rise_time_ns = 650,
 			.fall_time_ns = 400,
 			.data_hold_time_ns = 50,
 		},
 		.i2c[1] = {
 			.speed = I2C_SPEED_FAST,
 			.rise_time_ns = 650,
 			.fall_time_ns = 400,
 			.data_hold_time_ns = 50,
 		},
 		.i2c[3] = {
 			.speed = I2C_SPEED_FAST,
 			.rise_time_ns = 650,
 			.fall_time_ns = 400,
 			.data_hold_time_ns = 50,
 		},
 		.i2c[4] = {
 			.early_init = 1,
 			.speed = I2C_SPEED_FAST,
 			.rise_time_ns = 600,
 			.fall_time_ns = 400,
 			.data_hold_time_ns = 50,
 		},
 		.i2c[5] = {
 			.speed = I2C_SPEED_FAST,
 			.rise_time_ns = 900,
 			.fall_time_ns = 400,
 			.data_hold_time_ns = 50,
 		},
 	}"

 	device domain 0 on
 		device ref pcie_rp9 on
 			# Enable SSD Card PCIE 9 using clk 4
 			register "pcie_rp[PCH_RP(9)]" = "{
 				.clk_src = 4,
 				.clk_req = 4,
 				.flags = PCIE_RP_LTR | PCIE_RP_AER,
 			}"
 		end	#PCIE9 SSD card
 		device ref pcie_rp11 on
 			# Enable SD Card PCIE 11 using clk 2
 			register "pcie_rp[PCH_RP(11)]" = "{
 				.clk_src = 2,
 				.clk_req = 2,
 				.flags = PCIE_RP_HOTPLUG | PCIE_RP_LTR | PCIE_RP_AER,
 			}"
 		end	#PCIE11 SD card
 		device ref tbt_pcie_rp0 on end
 		device ref tbt_pcie_rp1 on end
 		device ref tbt_pcie_rp2 on end
 		device ref tbt_pcie_rp3 on end
 		device ref tcss_xhci on
 			chip drivers/usb/acpi
 				device ref tcss_root_hub on
 					chip drivers/usb/acpi
 						register "desc" = ""USB3 Type-C Port C0 (MLB)""
 						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
 						register "use_custom_pld" = "true"
 						register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(1, 1))"
 						device ref tcss_usb3_port1 on end
 					end
 					chip drivers/usb/acpi
 						register "desc" = ""USB3 Type-C Port C1 (DB)""
 						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
 						register "use_custom_pld" = "true"
 						register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))"
 						device ref tcss_usb3_port3 on end
 					end
 				end
 			end
 		end
 		device ref tcss_dma0 on
 			chip drivers/intel/usb4/retimer
 				register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B22)"
 				use tcss_usb3_port1 as dfp[0].typec_port
 				device generic 0 on end
 			end
 		end
 		device ref tcss_dma1 on
 			chip drivers/intel/usb4/retimer
 				register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B22)"
 				use tcss_usb3_port3 as dfp[0].typec_port
 				device generic 0 on end
 			end
 		end
 		device ref xhci on
 			chip drivers/usb/acpi
 				device ref xhci_root_hub on
 					chip drivers/usb/acpi
 						register "desc" = ""USB2 Type-C Port C0 (MLB)""
 						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
 						register "use_custom_pld" = "true"
 						register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(1, 1))"
 						device ref usb2_port2 on end
 					end
 					chip drivers/usb/acpi
 						register "desc" = ""USB2 Type-C Port C1 (DB)""
 						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
 						register "use_custom_pld" = "true"
 						register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))"
 						device ref usb2_port4 on end
 					end
 					chip drivers/usb/acpi
 						register "desc" = ""USB2 WWAN""
 						register "type" = "UPC_TYPE_INTERNAL"
 						device ref usb2_port5 on end
 					end
 					chip drivers/usb/acpi
 						register "desc" = ""USB2 Camera""
 						register "type" = "UPC_TYPE_INTERNAL"
 						device ref usb2_port6 on end
 					end
 					chip drivers/usb/acpi
 						register "desc" = ""USB2 Type-A Port A0 (DB)""
 						register "type" = "UPC_TYPE_A"
 						register "use_custom_pld" = "true"
 						register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 2))"
 						device ref usb2_port9 on end
 					end
 					chip drivers/usb/acpi
 						register "desc" = ""USB2 Bluetooth""
 						register "type" = "UPC_TYPE_INTERNAL"
 						register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_B01)"
 						device ref usb2_port10 on end
 					end
 					chip drivers/usb/acpi
 						register "desc" = ""USB3 Type-A Port A0 (DB)""
 						register "type" = "UPC_TYPE_USB3_A"
 						register "use_custom_pld" = "true"
 						register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 2))"
 						device ref usb3_port1 on end
 					end
 				end
 			end
 		end
 		device ref cnvi_wifi on
 			chip drivers/wifi/generic
 				register "wake" = "GPE0_PME_B0"
 				register "is_untrusted" = "true"
 				device generic 0 on end
 			end
 		end
 		device ref ipu on
 			chip drivers/intel/mipi_camera
 				register "acpi_uid" = "0x50000"
 				register "acpi_name" = ""IPU0""
 				register "device_type" = "INTEL_ACPI_CAMERA_CIO2"

 				register "cio2_num_ports" = "2"
 				register "cio2_lanes_used" = "{2,2}" # 2 CSI Camera lanes are used
 				register "cio2_lane_endpoint[0]" = ""^I2C0.CAM0""
 				register "cio2_lane_endpoint[1]" = ""^I2C5.CAM1""
 				register "cio2_prt[0]" = "4"
 				register "cio2_prt[1]" = "0"

 				device generic 0 on end
 			end
 		end
 		device ref i2c0 on
 			chip drivers/i2c/generic
 				register "hid" = ""RTL5682""
 				register "name" = ""RT58""
 				register "desc" = ""Headset Codec""
 				register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_B06)"
 				# Set the jd_src to RT5668_JD1 for jack detection
 				register "property_count" = "1"
 				register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
 				register "property_list[0].name" = ""realtek,jd-src""
 				register "property_list[0].integer" = "1"
 				device i2c 1a on end
 			end
 			chip drivers/intel/mipi_camera
 				register "acpi_hid" = ""OVTI8856""
 				register "acpi_uid" = "0"
 				register "acpi_name" = ""CAM0""
 				register "chip_name" = ""Ov 8856 Camera""
 				register "device_type" = "INTEL_ACPI_CAMERA_SENSOR"

 				register "ssdb.lanes_used" = "2"
 				register "ssdb.link_used" = "0"
 				register "ssdb.vcm_type" = "0x0C"
 				register "vcm_name" = ""VCM0""
 				register "num_freq_entries" = "2"
 				register "link_freq[0]" = "720 * MHz" # 720 MHz
 				register "link_freq[1]" = "360 * MHz" # 360 MHz
 				register "remote_name" = ""IPU0""

 				register "has_power_resource" = "1"
 				#Controls
 				register "clk_panel.clks[0].clknum" = "1" # IMGCLKOUT_1
 				register "clk_panel.clks[0].freq" = "1" # FREQ_19_2_MHZ

 				register "gpio_panel.gpio[0].gpio_num" = "GPP_C03" #EN_WCAM_SENR_PWR
 				register "gpio_panel.gpio[1].gpio_num" = "GPP_C04" #EN_WCAM_PWR
 				register "gpio_panel.gpio[2].gpio_num" = "GPP_V22" #WCAM_RST_L

 				#_ON
 				register "on_seq.ops_cnt" = "5"
 				register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)"
 				register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 0)"
 				register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 0)"
 				register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 0)"
 				register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 10)"

 				#_OFF
 				register "off_seq.ops_cnt" = "4"
 				register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)"
 				register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)"
 				register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)"
 				register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)"

 				device i2c 10 on end
 			end
 			chip drivers/intel/mipi_camera
 				register "acpi_uid" = "2"
 				register "acpi_name" = ""VCM0""
 				register "chip_name" = ""DW9714 VCM""
 				register "device_type" = "INTEL_ACPI_CAMERA_VCM"

 				register "pr0" = ""\\_SB.PCI0.I2C0.CAM0.PRIC""
 				register "vcm_compat" = ""dongwoon,dw9714""

 				device i2c 0C on end
 			end
 			chip drivers/intel/mipi_camera
 				register "acpi_uid" = "1"
 				register "acpi_name" = ""NVM0""
 				register "chip_name" = ""ST M24C64X""
 				register "device_type" = "INTEL_ACPI_CAMERA_NVM"

 				register "pr0" = ""\\_SB.PCI0.I2C0.CAM0.PRIC""
 				register "nvm_compat" = ""atmel,24c64""

 				register "nvm_size" = "0x10000"
 				register "nvm_pagesize" = "0x01"
 				register "nvm_readonly" = "0x01"
 				register "nvm_width" = "0x0E"

 				device i2c 50 on end
 			end
 		end #I2C0
 		device ref i2c1 on
 			chip drivers/i2c/hid
 				register "generic.hid" = ""ELAN6918""
 				register "generic.desc" = ""ELAN Touchscreen""
 				register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C07_IRQ)"
 				register "generic.probed" = "1"
 				register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C01)"
 				register "generic.reset_delay_ms" = "20"
 				register "generic.reset_off_delay_ms" = "2"
 				register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C00)"
 				register "generic.enable_delay_ms" = "1"
 				register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C06)"
 				register "generic.stop_off_delay_ms" = "2"
 				register "generic.has_power_resource" = "1"
 				register "hid_desc_reg_offset" = "0x01"
 				device i2c 10 on end
 			end
 		end
 		device ref i2c2 on end
 		device ref i2c3 on
 			chip drivers/i2c/generic
 				register "hid" = ""ELAN0000""
 				register "desc" = ""ELAN Touchpad""
 				register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_B00_IRQ)"
 				register "wake" = "GPE0_DW0_00"
 				register "detect" = "1"
 				device i2c 15 on end
 			end
 		end
 		device ref sata on end
 		device ref i2c4 on
 			chip drivers/i2c/tpm
 				register "hid" = ""GOOG0005""
 				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E03_IRQ)"
 				device i2c 50 on end
 			end
 		end
 		device ref i2c5 on
 			chip drivers/intel/mipi_camera
 				register "acpi_hid" = ""INT3474""
 				register "acpi_uid" = "0"
 				register "acpi_name" = ""CAM1""
 				register "chip_name" = ""Ov 2740 Camera""
 				register "device_type" = "INTEL_ACPI_CAMERA_SENSOR"
 				register "has_power_resource" = "1"

 				register "ssdb.lanes_used" = "2"
 				register "ssdb.link_used" = "1"
 				register "num_freq_entries" = "1"
 				register "link_freq[0]" = "360 * MHz"
 				register "remote_name" = ""IPU0""
 				register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D3_COLD"

 				#Controls
 				register "gpio_panel.gpio[0].gpio_num" = "GPP_A11" #EN_UCAM_SENR_PWR
 				register "gpio_panel.gpio[1].gpio_num" = "GPP_B09" #EN_FCAM_PWR
 				register "gpio_panel.gpio[2].gpio_num" = "GPP_V23" #UCAM_RST_L

 				#_ON
 				register "on_seq.ops_cnt" = "4"
 				register "on_seq.ops[0]" = "SEQ_OPS_GPIO_ENABLE(0, 0)"
 				register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(1, 0)"
 				register "on_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(2, 0)"
 				register "on_seq.ops[3]" = "SEQ_OPS_GPIO_ENABLE(2, 10)"

 				#_OFF
 				register "off_seq.ops_cnt" = "3"
 				register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(2, 0)"
 				register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(1, 0)"
 				register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(0, 0)"

 				device i2c 36 on end
 			end
 			chip drivers/intel/mipi_camera
 				register "acpi_hid" = "ACPI_DT_NAMESPACE_HID"
 				register "acpi_uid" = "1"
 				register "acpi_name" = ""NVM1""
 				register "chip_name" = ""ST M24C64X""
 				register "device_type" = "INTEL_ACPI_CAMERA_NVM"
 				register "pr0" = ""\\_SB.PCI0.I2C5.CAM1.PRIC""

 				register "nvm_size" = "0x10000"
 				register "nvm_pagesize" = "1"
 				register "nvm_readonly" = "1"
 				register "nvm_width" = "0x10"
 				register "nvm_compat" = ""atmel,24c64""

 				device i2c 50 on end
 			end
 		end #I2C5
 		device ref pcie_rp5 on
 			# Enable WLAN Card PCIE 5 using clk 5
 			register "pcie_rp[PCH_RP(5)]" = "{
 				.clk_src = 5,
 				.clk_req = 5,
 				.flags = PCIE_RP_HOTPLUG | PCIE_RP_LTR | PCIE_RP_AER,
 			}"
 		end	#PCIE5 WLAN card
 		device ref pcie_rp6 on
 			# Enable WWAN Card PCIE 6 using clk 3
 			register "pcie_rp[PCH_RP(6)]" = "{
 				.clk_src = 3,
 				.clk_req = 3,
 				.flags = PCIE_RP_HOTPLUG | PCIE_RP_LTR | PCIE_RP_AER,
 			}"
 			chip soc/intel/common/block/pcie/rtd3
 				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C05)"
 				register "reset_off_delay_ms" = "20"
 				register "srcclk_pin" = "3"
 				register "ext_pm_support" = "ACPI_PCIE_RP_EMIT_ALL"
 				register "skip_on_off_support" = "true"
 				device generic 0 alias rp6_rtd3 on end
 			end
 			chip drivers/wwan/fm
 				register "fcpo_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E07)"
 				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A15)"
 				register "perst_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C05)"
 				register "wake_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_F10)"
 				register "add_acpi_dma_property" = "true"
 				use rp6_rtd3 as rtd3dev
 				device generic 0 on end
 			end
 		end	#PCIE6 WWAN card
 		device ref gspi1 on end
 		device ref soc_espi on
 			chip ec/google/chromeec
 				use conn0 as mux_conn[0]
 				use conn1 as mux_conn[1]
 				device pnp 0c09.0 on end
 			end
 		end
 		device ref pmc hidden
 			chip drivers/intel/pmc_mux
 				device generic 0 on
 					chip drivers/intel/pmc_mux/conn
 						use usb2_port2 as usb2_port
 						use tcss_usb3_port1 as usb3_port
 						device generic 0 alias conn0 on end
 					end
 					chip drivers/intel/pmc_mux/conn
 						use usb2_port4 as usb2_port
 						use tcss_usb3_port3 as usb3_port
 						device generic 1 alias conn1 on end
 					end
 				end
 			end
 		end
 		device ref hda on
 			chip drivers/generic/max98357a
 				register "hid" = ""MX98357A""
 				register "sdmode_gpio" =
 						"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D04)"
 				register "sdmode_delay" = "5"
 				device generic 0 on end
 			end
 		end
 	end
 end
	chip soc/intel/meteorlake

	register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC0)" # USB2_C0
	register "usb2_ports[3]" = "USB2_PORT_TYPE_C(OC_SKIP)" # USB2_C1
	register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)" # M.2 WWAN
	register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # M.2 Camera
	register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # DCI
	register "usb2_ports[8]" = "USB2_PORT_MID(OC3)" # Type-A Port A0
	register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # M.2 Bluetooth

	register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC3)" # USB3/2 Type A port A0
	register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # DCI

	register "tcss_ports[0]" = "TCSS_PORT_DEFAULT(OC0)"
	register "tcss_ports[2]" = "TCSS_PORT_DEFAULT(OC_SKIP)"

	# Enable eDP in Port A
	register "ddi_port_A_config" = "1"
	# Enable HDMI in Port B
	register "ddi_port_B_config" = "0"

	# Enable Display Port Configuration
	register "ddi_ports_config" = "{
	[DDI_PORT_A] = DDI_ENABLE_HPD,
	[DDI_PORT_B] = DDI_ENABLE_HPD \| DDI_ENABLE_DDC,
	}"

	register "serial_io_gspi_mode" = "{
	[PchSerialIoIndexGSPI0] = PchSerialIoDisabled,
	[PchSerialIoIndexGSPI1] = PchSerialIoPci,
	[PchSerialIoIndexGSPI2] = PchSerialIoDisabled,
	}"

	register "serial_io_i2c_mode" = "{
	[PchSerialIoIndexI2C0] = PchSerialIoPci,
	[PchSerialIoIndexI2C1] = PchSerialIoPci,
	[PchSerialIoIndexI2C2] = PchSerialIoDisabled,
	[PchSerialIoIndexI2C3] = PchSerialIoPci,
	[PchSerialIoIndexI2C4] = PchSerialIoPci,
	[PchSerialIoIndexI2C5] = PchSerialIoPci,
	}"

	# Intel Common SoC Config
	#+-------------------+---------------------------+
	#\| Field \| Value \|
	#+-------------------+---------------------------+
	#\| I2C0 \| Audio and WFC \|
	#\| I2C1 \| Touchscreen \|
	#\| I2C3 \| Touchpad \|
	#\| I2C4 \| cr50 TPM. Early init is \|
	#\| \| required to set up a BAR \|
	#\| \| for TPM communication \|
	#\| I2C5 \| UFC, SAR1, SAR2, HPS \|
	#+-------------------+---------------------------+
	register "common_soc_config" = "{
	.i2c[0] = {
	.speed = I2C_SPEED_FAST,
	.rise_time_ns = 650,
	.fall_time_ns = 400,
	.data_hold_time_ns = 50,
	},
	.i2c[1] = {
	.speed = I2C_SPEED_FAST,
	.rise_time_ns = 650,
	.fall_time_ns = 400,
	.data_hold_time_ns = 50,
	},
	.i2c[3] = {
	.speed = I2C_SPEED_FAST,
	.rise_time_ns = 650,
	.fall_time_ns = 400,
	.data_hold_time_ns = 50,
	},
	.i2c[4] = {
	.early_init = 1,
	.speed = I2C_SPEED_FAST,
	.rise_time_ns = 600,
	.fall_time_ns = 400,
	.data_hold_time_ns = 50,
	},
	.i2c[5] = {
	.speed = I2C_SPEED_FAST,
	.rise_time_ns = 900,
	.fall_time_ns = 400,
	.data_hold_time_ns = 50,
	},
	}"

	device domain 0 on
	device ref pcie_rp9 on
	# Enable SSD Card PCIE 9 using clk 4
	register "pcie_rp[PCH_RP(9)]" = "{
	.clk_src = 4,
	.clk_req = 4,
	.flags = PCIE_RP_LTR \| PCIE_RP_AER,
	}"
	end #PCIE9 SSD card
	device ref pcie_rp11 on
	# Enable SD Card PCIE 11 using clk 2
	register "pcie_rp[PCH_RP(11)]" = "{
	.clk_src = 2,
	.clk_req = 2,
	.flags = PCIE_RP_HOTPLUG \| PCIE_RP_LTR \| PCIE_RP_AER,
	}"
	end #PCIE11 SD card
	device ref tbt_pcie_rp0 on end
	device ref tbt_pcie_rp1 on end
	device ref tbt_pcie_rp2 on end
	device ref tbt_pcie_rp3 on end
	device ref tcss_xhci on
	chip drivers/usb/acpi
	device ref tcss_root_hub on
	chip drivers/usb/acpi
	register "desc" = ""USB3 Type-C Port C0 (MLB)""
	register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
	register "use_custom_pld" = "true"
	register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(1, 1))"
	device ref tcss_usb3_port1 on end
	end
	chip drivers/usb/acpi
	register "desc" = ""USB3 Type-C Port C1 (DB)""
	register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
	register "use_custom_pld" = "true"
	register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))"
	device ref tcss_usb3_port3 on end
	end
	end
	end
	end
	device ref tcss_dma0 on
	chip drivers/intel/usb4/retimer
	register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B22)"
	use tcss_usb3_port1 as dfp[0].typec_port
	device generic 0 on end
	end
	end
	device ref tcss_dma1 on
	chip drivers/intel/usb4/retimer
	register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B22)"
	use tcss_usb3_port3 as dfp[0].typec_port
	device generic 0 on end
	end
	end
	device ref xhci on
	chip drivers/usb/acpi
	device ref xhci_root_hub on
	chip drivers/usb/acpi
	register "desc" = ""USB2 Type-C Port C0 (MLB)""
	register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
	register "use_custom_pld" = "true"
	register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(1, 1))"
	device ref usb2_port2 on end
	end
	chip drivers/usb/acpi
	register "desc" = ""USB2 Type-C Port C1 (DB)""
	register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
	register "use_custom_pld" = "true"
	register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))"
	device ref usb2_port4 on end
	end
	chip drivers/usb/acpi
	register "desc" = ""USB2 WWAN""
	register "type" = "UPC_TYPE_INTERNAL"
	device ref usb2_port5 on end
	end
	chip drivers/usb/acpi
	register "desc" = ""USB2 Camera""
	register "type" = "UPC_TYPE_INTERNAL"
	device ref usb2_port6 on end
	end
	chip drivers/usb/acpi
	register "desc" = ""USB2 Type-A Port A0 (DB)""
	register "type" = "UPC_TYPE_A"
	register "use_custom_pld" = "true"
	register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 2))"
	device ref usb2_port9 on end
	end
	chip drivers/usb/acpi
	register "desc" = ""USB2 Bluetooth""
	register "type" = "UPC_TYPE_INTERNAL"
	register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_B01)"
	device ref usb2_port10 on end
	end
	chip drivers/usb/acpi
	register "desc" = ""USB3 Type-A Port A0 (DB)""
	register "type" = "UPC_TYPE_USB3_A"
	register "use_custom_pld" = "true"
	register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 2))"
	device ref usb3_port1 on end
	end
	end
	end
	end
	device ref cnvi_wifi on
	chip drivers/wifi/generic
	register "wake" = "GPE0_PME_B0"
	register "is_untrusted" = "true"
	device generic 0 on end
	end
	end
	device ref ipu on
	chip drivers/intel/mipi_camera
	register "acpi_uid" = "0x50000"
	register "acpi_name" = ""IPU0""
	register "device_type" = "INTEL_ACPI_CAMERA_CIO2"

	register "cio2_num_ports" = "2"
	register "cio2_lanes_used" = "{2,2}" # 2 CSI Camera lanes are used
	register "cio2_lane_endpoint[0]" = ""^I2C0.CAM0""
	register "cio2_lane_endpoint[1]" = ""^I2C5.CAM1""
	register "cio2_prt[0]" = "4"
	register "cio2_prt[1]" = "0"

	device generic 0 on end
	end
	end
	device ref i2c0 on
	chip drivers/i2c/generic
	register "hid" = ""RTL5682""
	register "name" = ""RT58""
	register "desc" = ""Headset Codec""
	register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_B06)"
	# Set the jd_src to RT5668_JD1 for jack detection
	register "property_count" = "1"
	register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
	register "property_list[0].name" = ""realtek,jd-src""
	register "property_list[0].integer" = "1"
	device i2c 1a on end
	end
	chip drivers/intel/mipi_camera
	register "acpi_hid" = ""OVTI8856""
	register "acpi_uid" = "0"
	register "acpi_name" = ""CAM0""
	register "chip_name" = ""Ov 8856 Camera""
	register "device_type" = "INTEL_ACPI_CAMERA_SENSOR"

	register "ssdb.lanes_used" = "2"
	register "ssdb.link_used" = "0"
	register "ssdb.vcm_type" = "0x0C"
	register "vcm_name" = ""VCM0""
	register "num_freq_entries" = "2"
	register "link_freq[0]" = "720 * MHz" # 720 MHz
	register "link_freq[1]" = "360 * MHz" # 360 MHz
	register "remote_name" = ""IPU0""

	register "has_power_resource" = "1"
	#Controls
	register "clk_panel.clks[0].clknum" = "1" # IMGCLKOUT_1
	register "clk_panel.clks[0].freq" = "1" # FREQ_19_2_MHZ

	register "gpio_panel.gpio[0].gpio_num" = "GPP_C03" #EN_WCAM_SENR_PWR
	register "gpio_panel.gpio[1].gpio_num" = "GPP_C04" #EN_WCAM_PWR
	register "gpio_panel.gpio[2].gpio_num" = "GPP_V22" #WCAM_RST_L

	#_ON
	register "on_seq.ops_cnt" = "5"
	register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)"
	register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 0)"
	register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 0)"
	register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 0)"
	register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 10)"

	#_OFF
	register "off_seq.ops_cnt" = "4"
	register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)"
	register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)"
	register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)"
	register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)"

	device i2c 10 on end
	end
	chip drivers/intel/mipi_camera
	register "acpi_uid" = "2"
	register "acpi_name" = ""VCM0""
	register "chip_name" = ""DW9714 VCM""
	register "device_type" = "INTEL_ACPI_CAMERA_VCM"

	register "pr0" = ""\\_SB.PCI0.I2C0.CAM0.PRIC""
	register "vcm_compat" = ""dongwoon,dw9714""

	device i2c 0C on end
	end
	chip drivers/intel/mipi_camera
	register "acpi_uid" = "1"
	register "acpi_name" = ""NVM0""
	register "chip_name" = ""ST M24C64X""
	register "device_type" = "INTEL_ACPI_CAMERA_NVM"

	register "pr0" = ""\\_SB.PCI0.I2C0.CAM0.PRIC""
	register "nvm_compat" = ""atmel,24c64""

	register "nvm_size" = "0x10000"
	register "nvm_pagesize" = "0x01"
	register "nvm_readonly" = "0x01"
	register "nvm_width" = "0x0E"

	device i2c 50 on end
	end
	end #I2C0
	device ref i2c1 on
	chip drivers/i2c/hid
	register "generic.hid" = ""ELAN6918""
	register "generic.desc" = ""ELAN Touchscreen""
	register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C07_IRQ)"
	register "generic.probed" = "1"
	register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C01)"
	register "generic.reset_delay_ms" = "20"
	register "generic.reset_off_delay_ms" = "2"
	register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C00)"
	register "generic.enable_delay_ms" = "1"
	register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C06)"
	register "generic.stop_off_delay_ms" = "2"
	register "generic.has_power_resource" = "1"
	register "hid_desc_reg_offset" = "0x01"
	device i2c 10 on end
	end
	end
	device ref i2c2 on end
	device ref i2c3 on
	chip drivers/i2c/generic
	register "hid" = ""ELAN0000""
	register "desc" = ""ELAN Touchpad""
	register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_B00_IRQ)"
	register "wake" = "GPE0_DW0_00"
	register "detect" = "1"
	device i2c 15 on end
	end
	end
	device ref sata on end
	device ref i2c4 on
	chip drivers/i2c/tpm
	register "hid" = ""GOOG0005""
	register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E03_IRQ)"
	device i2c 50 on end
	end
	end
	device ref i2c5 on
	chip drivers/intel/mipi_camera
	register "acpi_hid" = ""INT3474""
	register "acpi_uid" = "0"
	register "acpi_name" = ""CAM1""
	register "chip_name" = ""Ov 2740 Camera""
	register "device_type" = "INTEL_ACPI_CAMERA_SENSOR"
	register "has_power_resource" = "1"

	register "ssdb.lanes_used" = "2"
	register "ssdb.link_used" = "1"
	register "num_freq_entries" = "1"
	register "link_freq[0]" = "360 * MHz"
	register "remote_name" = ""IPU0""
	register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D3_COLD"

	#Controls
	register "gpio_panel.gpio[0].gpio_num" = "GPP_A11" #EN_UCAM_SENR_PWR
	register "gpio_panel.gpio[1].gpio_num" = "GPP_B09" #EN_FCAM_PWR
	register "gpio_panel.gpio[2].gpio_num" = "GPP_V23" #UCAM_RST_L

	#_ON
	register "on_seq.ops_cnt" = "4"
	register "on_seq.ops[0]" = "SEQ_OPS_GPIO_ENABLE(0, 0)"
	register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(1, 0)"
	register "on_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(2, 0)"
	register "on_seq.ops[3]" = "SEQ_OPS_GPIO_ENABLE(2, 10)"

	#_OFF
	register "off_seq.ops_cnt" = "3"
	register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(2, 0)"
	register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(1, 0)"
	register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(0, 0)"

	device i2c 36 on end
	end
	chip drivers/intel/mipi_camera
	register "acpi_hid" = "ACPI_DT_NAMESPACE_HID"
	register "acpi_uid" = "1"
	register "acpi_name" = ""NVM1""
	register "chip_name" = ""ST M24C64X""
	register "device_type" = "INTEL_ACPI_CAMERA_NVM"
	register "pr0" = ""\\_SB.PCI0.I2C5.CAM1.PRIC""

	register "nvm_size" = "0x10000"
	register "nvm_pagesize" = "1"
	register "nvm_readonly" = "1"
	register "nvm_width" = "0x10"
	register "nvm_compat" = ""atmel,24c64""

	device i2c 50 on end
	end
	end #I2C5
	device ref pcie_rp5 on
	# Enable WLAN Card PCIE 5 using clk 5
	register "pcie_rp[PCH_RP(5)]" = "{
	.clk_src = 5,
	.clk_req = 5,
	.flags = PCIE_RP_HOTPLUG \| PCIE_RP_LTR \| PCIE_RP_AER,
	}"
	end #PCIE5 WLAN card
	device ref pcie_rp6 on
	# Enable WWAN Card PCIE 6 using clk 3
	register "pcie_rp[PCH_RP(6)]" = "{
	.clk_src = 3,
	.clk_req = 3,
	.flags = PCIE_RP_HOTPLUG \| PCIE_RP_LTR \| PCIE_RP_AER,
	}"
	chip soc/intel/common/block/pcie/rtd3
	register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C05)"
	register "reset_off_delay_ms" = "20"
	register "srcclk_pin" = "3"
	register "ext_pm_support" = "ACPI_PCIE_RP_EMIT_ALL"
	register "skip_on_off_support" = "true"
	device generic 0 alias rp6_rtd3 on end
	end
	chip drivers/wwan/fm
	register "fcpo_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E07)"
	register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A15)"
	register "perst_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C05)"
	register "wake_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_F10)"
	register "add_acpi_dma_property" = "true"
	use rp6_rtd3 as rtd3dev
	device generic 0 on end
	end
	end #PCIE6 WWAN card
	device ref gspi1 on end
	device ref soc_espi on
	chip ec/google/chromeec
	use conn0 as mux_conn[0]
	use conn1 as mux_conn[1]
	device pnp 0c09.0 on end
	end
	end
	device ref pmc hidden
	chip drivers/intel/pmc_mux
	device generic 0 on
	chip drivers/intel/pmc_mux/conn
	use usb2_port2 as usb2_port
	use tcss_usb3_port1 as usb3_port
	device generic 0 alias conn0 on end
	end
	chip drivers/intel/pmc_mux/conn
	use usb2_port4 as usb2_port
	use tcss_usb3_port3 as usb3_port
	device generic 1 alias conn1 on end
	end
	end
	end
	end
	device ref hda on
	chip drivers/generic/max98357a
	register "hid" = ""MX98357A""
	register "sdmode_gpio" =
	"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D04)"
	register "sdmode_delay" = "5"
	device generic 0 on end
	end
	end
	end
	end