| chip northbridge/intel/sandybridge |
| # IGD Displays |
| register "gfx.ndid" = "3" |
| register "gfx.did" = "{ 0x80000100, 0x80000240, 0x80000410, 0x80000410, 0x00000005 }" |
| |
| # Enable DisplayPort Hotplug with 6ms pulse |
| register "gpu_dp_d_hotplug" = "0x06" |
| |
| # Enable Panel as LVDS and configure power delays |
| register "gpu_panel_port_select" = "0" # LVDS |
| register "gpu_panel_power_cycle_delay" = "5" |
| register "gpu_panel_power_up_delay" = "300" # T1+T2: 30ms |
| register "gpu_panel_power_down_delay" = "300" # T5+T6: 30ms |
| register "gpu_panel_power_backlight_on_delay" = "2000" # T3: 200ms |
| register "gpu_panel_power_backlight_off_delay" = "2000" # T4: 200ms |
| register "gfx.use_spread_spectrum_clock" = "1" |
| register "gfx.link_frequency_270_mhz" = "1" |
| register "gpu_cpu_backlight" = "0x1155" |
| register "gpu_pch_backlight" = "0x06100610" |
| |
| device cpu_cluster 0 on |
| chip cpu/intel/socket_rPGA988B |
| device lapic 0 on end |
| end |
| chip cpu/intel/model_206ax |
| # Magic APIC ID to locate this chip |
| device lapic 0xacac off end |
| |
| register "c1_acpower" = "1" # ACPI(C1) = MWAIT(C1) |
| register "c2_acpower" = "3" # ACPI(C2) = MWAIT(C3) |
| register "c3_acpower" = "5" # ACPI(C3) = MWAIT(C7) |
| |
| register "c1_battery" = "1" # ACPI(C1) = MWAIT(C1) |
| register "c2_battery" = "3" # ACPI(C2) = MWAIT(C3) |
| register "c3_battery" = "5" # ACPI(C3) = MWAIT(C7) |
| end |
| end |
| |
| register "pci_mmio_size" = "2048" |
| |
| device domain 0 on |
| device pci 00.0 on end # host bridge |
| device pci 01.0 on end # NVIDIA Corporation GF119M [NVS 4200M] |
| device pci 02.0 on end # vga controller |
| |
| chip southbridge/intel/bd82x6x # Intel Series 6 Cougar Point PCH |
| # GPI routing |
| # 0 No effect (default) |
| # 1 SMI# (if corresponding ALT_GPI_SMI_EN bit is also set) |
| # 2 SCI (if corresponding GPIO_EN bit is also set) |
| register "alt_gp_smi_en" = "0x0000" |
| register "gpi1_routing" = "2" |
| register "gpi13_routing" = "2" |
| |
| # Enable SATA ports 0 (HDD bay) & 1 (ODD bay) & 2 (mSATA) & 3 (eSATA) & 4 (dock) |
| register "sata_port_map" = "0x1f" |
| # Set max SATA speed to 6.0 Gb/s |
| register "sata_interface_speed_support" = "0x3" |
| |
| register "gen1_dec" = "0x7c1601" |
| register "gen2_dec" = "0x0c15e1" |
| register "gen4_dec" = "0x0c06a1" |
| |
| # Enable zero-based linear PCIe root port functions |
| register "pcie_port_coalesce" = "1" |
| |
| register "c2_latency" = "101" # c2 not supported |
| register "p_cnt_throttling_supported" = "1" |
| |
| register "pcie_hotplug_map" = "{ 0, 0, 0, 1, 0, 0, 0, 0 }" |
| |
| register "spi_uvscc" = "0x2005" |
| register "spi_lvscc" = "0x2005" |
| |
| device pci 16.0 on end # Management Engine Interface 1 |
| device pci 16.1 off end |
| device pci 16.2 off end |
| device pci 16.3 off end |
| device pci 19.0 on end # Intel Gigabit Ethernet |
| device pci 1a.0 on end # USB2 EHCI #2 |
| device pci 1b.0 on end # High Definition Audio |
| device pci 1c.0 off end # PCIe Port #1 |
| device pci 1c.1 on end # PCIe Port #2 Integrated Wireless LAN |
| device pci 1c.2 off end # PCIe Port #3 |
| device pci 1c.3 on end # PCIe Port #4 Express Card |
| device pci 1c.4 on end # PCIe Port #5 MMC/SDXC + IEEE1394 |
| device pci 1c.5 off end # PCIe Port #6 Intel Ethernet PHY |
| device pci 1c.6 on end # PCIe Port #7 USB 3.0 only W520 |
| device pci 1c.7 off end # PCIe Port #8 |
| device pci 1d.0 on end # USB2 EHCI #1 |
| device pci 1f.0 on #LPC bridge |
| chip ec/lenovo/pmh7 |
| device pnp ff.1 on # dummy |
| end |
| register "backlight_enable" = "0x01" |
| register "dock_event_enable" = "0x01" |
| end |
| |
| chip drivers/pc80/tpm |
| device pnp 0c31.0 on end |
| end |
| |
| chip ec/lenovo/h8 |
| device pnp ff.2 on # dummy |
| io 0x60 = 0x62 |
| io 0x62 = 0x66 |
| io 0x64 = 0x1600 |
| io 0x66 = 0x1604 |
| end |
| |
| register "config0" = "0xa7" |
| register "config1" = "0x09" |
| register "config2" = "0xa0" |
| register "config3" = "0xc2" |
| |
| register "beepmask0" = "0x00" |
| register "beepmask1" = "0x86" |
| register "has_power_management_beeps" = "0" |
| register "event2_enable" = "0xff" |
| register "event3_enable" = "0xff" |
| register "event4_enable" = "0xd0" |
| register "event5_enable" = "0xfc" |
| register "event6_enable" = "0x00" |
| register "event7_enable" = "0x01" |
| register "event8_enable" = "0x7b" |
| register "event9_enable" = "0xff" |
| register "eventa_enable" = "0x01" |
| register "eventb_enable" = "0x00" |
| register "eventc_enable" = "0xff" |
| register "eventd_enable" = "0xff" |
| register "evente_enable" = "0x0d" |
| |
| register "has_bdc_detection" = "1" |
| register "bdc_gpio_num" = "54" |
| register "bdc_gpio_lvl" = "0" |
| end |
| chip drivers/lenovo/hybrid_graphics |
| device pnp ff.f on end # dummy |
| |
| register "detect_gpio" = "21" |
| |
| register "has_panel_hybrid_gpio" = "1" |
| register "panel_hybrid_gpio" = "52" |
| register "panel_integrated_lvl" = "1" |
| |
| register "has_backlight_gpio" = "0" |
| register "has_dgpu_power_gpio" = "0" |
| |
| register "has_thinker1" = "1" |
| end |
| end # LPC bridge |
| device pci 1f.2 on end # SATA Controller 1 |
| device pci 1f.3 on # SMBUS controller |
| # eeprom, 8 virtual devices, same chip |
| chip drivers/i2c/at24rf08c |
| device i2c 54 on end |
| device i2c 55 on end |
| device i2c 56 on end |
| device i2c 57 on end |
| device i2c 5c on end |
| device i2c 5d on end |
| device i2c 5e on end |
| device i2c 5f on end |
| end |
| end # SMBus |
| end |
| end |
| end |
