| # SPDX-License-Identifier: GPL-2.0-or-later |
| |
| fw_config |
| field AUDIO_AMP 35 |
| option AUDIO_AMP_I2C_MODE 0 |
| option AUDIO_AMP_AUTO_MODE 1 |
| end |
| end |
| |
| chip soc/amd/picasso |
| |
| # Start : OPN Performance Configuration |
| # See devhub #56670 Chapter 5 for documentation |
| # For the below fields, 0 indicates use SOC default |
| |
| # System config index |
| register "system_config" = "1" |
| |
| # Set STAPM confiuration. All of these fields must be set >0 to take affect |
| register "slow_ppt_limit_mW" = "6000" |
| register "fast_ppt_limit_mW" = "9000" |
| register "slow_ppt_time_constant_s" = "5" |
| register "stapm_time_constant_s" = "1400" |
| register "sustained_power_limit_mW" = "4800" |
| |
| # End : OPN Performance Configuration |
| |
| register "telemetry_vddcr_vdd_slope_mA" = "27225" |
| register "telemetry_vddcr_vdd_offset" = "187" |
| register "telemetry_vddcr_soc_slope_mA" = "26559" |
| register "telemetry_vddcr_soc_offset" = "89" |
| |
| # eDP power sequence. all pwr sequence numbers below are in uint of 4ms, |
| # and "0" as default value |
| register "edp_pwr_adjust_enable" = "1" |
| register "pwron_digon_to_de" = "0" |
| register "pwron_de_to_varybl" = "0" |
| register "pwrdown_varybloff_to_de" = "0" |
| register "pwrdown_de_to_digoff" = "0" |
| register "pwroff_delay" = "0" |
| register "pwron_varybl_to_blon" = "5" |
| register "pwrdown_bloff_to_varybloff" = "5" |
| register "min_allowed_bl_level" = "0" |
| |
| # USB OC pin mapping |
| register "usb_port_overcurrent_pin[1]" = "USB_OC_NONE" # LTE instead of USB C1 |
| |
| # Controller0 Port0 |
| register "usb_2_port_tune_params[0]" = "{ |
| .com_pds_tune = 0x07, |
| .sq_rx_tune = 0x3, |
| .tx_fsls_tune = 0x3, |
| .tx_pre_emp_amp_tune = 0x03, |
| .tx_pre_emp_pulse_tune = 0x0, |
| .tx_rise_tune = 0x1, |
| .tx_vref_tune = 0x6, |
| .tx_hsxv_tune = 0x3, |
| .tx_res_tune = 0x01, |
| }" |
| |
| # Controller0 Port1 |
| register "usb_2_port_tune_params[1]" = "{ |
| .com_pds_tune = 0x07, |
| .sq_rx_tune = 0x3, |
| .tx_fsls_tune = 0x3, |
| .tx_pre_emp_amp_tune = 0x03, |
| .tx_pre_emp_pulse_tune = 0x0, |
| .tx_rise_tune = 0x1, |
| .tx_vref_tune = 0x6, |
| .tx_hsxv_tune = 0x3, |
| .tx_res_tune = 0x01, |
| }" |
| |
| # Controller0 Port2 |
| register "usb_2_port_tune_params[2]" = "{ |
| .com_pds_tune = 0x07, |
| .sq_rx_tune = 0x3, |
| .tx_fsls_tune = 0x3, |
| .tx_pre_emp_amp_tune = 0x03, |
| .tx_pre_emp_pulse_tune = 0x0, |
| .tx_rise_tune = 0x1, |
| .tx_vref_tune = 0x6, |
| .tx_hsxv_tune = 0x3, |
| .tx_res_tune = 0x01, |
| }" |
| |
| # Controller0 Port3 |
| register "usb_2_port_tune_params[3]" = "{ |
| .com_pds_tune = 0x07, |
| .sq_rx_tune = 0x3, |
| .tx_fsls_tune = 0x3, |
| .tx_pre_emp_amp_tune = 0x03, |
| .tx_pre_emp_pulse_tune = 0x0, |
| .tx_rise_tune = 0x1, |
| .tx_vref_tune = 0x6, |
| .tx_hsxv_tune = 0x3, |
| .tx_res_tune = 0x01, |
| }" |
| |
| # Controller1 Port0 |
| register "usb_2_port_tune_params[4]" = "{ |
| .com_pds_tune = 0x07, |
| .sq_rx_tune = 0x3, |
| .tx_fsls_tune = 0x3, |
| .tx_pre_emp_amp_tune = 0x03, |
| .tx_pre_emp_pulse_tune = 0x0, |
| .tx_rise_tune = 0x1, |
| .tx_vref_tune = 0x6, |
| .tx_hsxv_tune = 0x3, |
| .tx_res_tune = 0x01, |
| }" |
| |
| # Controller1 Port1 |
| register "usb_2_port_tune_params[5]" = "{ |
| .com_pds_tune = 0x07, |
| .sq_rx_tune = 0x3, |
| .tx_fsls_tune = 0x3, |
| .tx_pre_emp_amp_tune = 0x03, |
| .tx_pre_emp_pulse_tune = 0x0, |
| .tx_rise_tune = 0x1, |
| .tx_vref_tune = 0x6, |
| .tx_hsxv_tune = 0x3, |
| .tx_res_tune = 0x01, |
| }" |
| |
| # I2C2 for touchscreen and trackpad |
| register "i2c[2]" = "{ |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 18, /* 0 to 2.31 (3.3 * .7) */ |
| .fall_time_ns = 57, /* 2.31 to 0 */ |
| }" |
| |
| # I2C3 for H1 |
| register "i2c[3]" = "{ |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 110, |
| .fall_time_ns = 5, |
| .early_init = true, |
| }" |
| |
| register "emmc_config" = "{ |
| .timing = SD_EMMC_EMMC_HS400, |
| .sdr104_hs400_driver_strength = SD_EMMC_DRIVE_STRENGTH_A, |
| .init_khz_preset = 400, |
| }" |
| |
| # See AMD 55570-B1 Table 13: PCI Device ID Assignments. |
| device domain 0 on |
| subsystemid 0x1022 0x1510 inherit |
| device pci 1.3 on |
| chip drivers/generic/bayhub_lv2 |
| register "enable_power_saving" = "1" |
| device pci 00.0 on end |
| end |
| end # GPP Bridge 2 - SD |
| device pci 8.1 on |
| device pci 0.5 on |
| chip drivers/amd/i2s_machine_dev |
| register "hid" = ""AMDI1015"" |
| # DMIC select GPIO for ACP machine device |
| # This GPIO is used to select DMIC0 or DMIC1 by the |
| # kernel driver. It does not really have a polarity |
| # since low and high control the selection of DMIC and |
| # hence does not have an active polarity. |
| # Kernel driver does not use the polarity field and |
| # instead treats the GPIO selection as follows: |
| # Set low (0) = Select DMIC0 |
| # Set high (1) = Select DMIC1 |
| register "dmic_select_gpio" = "ACPI_GPIO_OUTPUT(GPIO_67)" |
| device generic 0.0 on |
| probe AUDIO_AMP AUDIO_AMP_I2C_MODE |
| end |
| end |
| chip drivers/amd/i2s_machine_dev |
| register "hid" = ""10021015"" |
| # DMIC select GPIO for ACP machine device |
| # This GPIO is used to select DMIC0 or DMIC1 by the |
| # kernel driver. It does not really have a polarity |
| # since low and high control the selection of DMIC and |
| # hence does not have an active polarity. |
| # Kernel driver does not use the polarity field and |
| # instead treats the GPIO selection as follows: |
| # Set low (0) = Select DMIC0 |
| # Set high (1) = Select DMIC1 |
| register "dmic_select_gpio" = "ACPI_GPIO_OUTPUT(GPIO_67)" |
| device generic 1.0 on |
| probe AUDIO_AMP AUDIO_AMP_AUTO_MODE |
| end |
| end |
| chip drivers/generic/alc1015 |
| register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_91)" |
| device generic 1.1 on |
| probe AUDIO_AMP AUDIO_AMP_AUTO_MODE |
| end |
| end |
| end # Audio |
| end |
| device pci 14.3 on # - D14F3 bridge |
| chip ec/google/chromeec |
| device pnp 0c09.0 on |
| chip ec/google/chromeec/i2c_tunnel |
| register "uid" = "1" |
| register "remote_bus" = "8" |
| device generic 0.1 on |
| chip drivers/i2c/generic |
| register "hid" = ""10EC1015"" |
| register "desc" = ""RT1015 Tweeter Left Speaker Amp"" |
| register "uid" = "0" |
| register "name" = ""TL"" |
| device i2c 28 on end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""10EC1015"" |
| register "desc" = ""RT1015 Tweeter Right Speaker Amp"" |
| register "uid" = "1" |
| register "name" = ""TR"" |
| device i2c 29 on end |
| end |
| probe AUDIO_AMP AUDIO_AMP_I2C_MODE |
| end |
| end |
| end |
| end |
| end |
| end # domain |
| |
| device mmio 0xfedc4000 on # APU_I2C2_BASE |
| chip drivers/i2c/hid |
| register "generic.hid" = ""GDIX0000"" |
| register "generic.desc" = ""Goodix Touchscreen"" |
| register "generic.irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPIO_12)" |
| register "generic.probed" = "1" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_32)" |
| register "generic.enable_delay_ms" = "10" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_140)" |
| register "generic.reset_off_delay_ms" = "2" |
| register "generic.reset_delay_ms" = "20" |
| register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_144)" |
| register "generic.stop_delay_ms" = "160" |
| register "generic.stop_off_delay_ms" = "2" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 5d on end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0001"" |
| register "desc" = ""ELAN Touchscreen"" |
| register "probed" = "1" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_LOW(GPIO_12)" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_32)" |
| register "enable_delay_ms" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_140)" |
| register "reset_delay_ms" = "20" |
| register "reset_off_delay_ms" = "2" |
| register "stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_144)" |
| register "stop_off_delay_ms" = "2" |
| register "has_power_resource" = "1" |
| register "disable_gpio_export_in_crs" = "1" |
| device i2c 10 on end |
| end |
| chip drivers/generic/gpio_keys |
| register "name" = ""PENH"" |
| register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPIO_4)" |
| register "key.dev_name" = ""EJCT"" |
| register "key.wakeup_event_action" = "EV_ACT_DEASSERTED" |
| register "key.linux_code" = "SW_PEN_INSERTED" |
| register "key.linux_input_type" = "EV_SW" |
| register "key.label" = ""pen_eject"" |
| register "key.debounce_interval" = "100" |
| register "key.wakeup_route" = "WAKEUP_ROUTE_GPIO_IRQ" |
| device generic 0 on end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_LOW(GPIO_9)" |
| register "wake" = "GEVENT_22" |
| register "probed" = "1" |
| device i2c 15 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""PNP0C50"" |
| register "generic.desc" = ""Synaptics Touchpad"" |
| register "generic.irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPIO_9)" |
| register "generic.wake" = "GEVENT_22" |
| register "generic.probed" = "1" |
| register "hid_desc_reg_offset" = "0x20" |
| device i2c 2c on end |
| end |
| chip drivers/i2c/sx9324 |
| register "desc" = ""SAR Proximity Sensor"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPIO_40)" |
| register "uid" = "2" |
| register "reg_gnrl_ctrl0" = "0x16" |
| register "reg_gnrl_ctrl1" = "0x21" |
| register "reg_afe_ctrl0" = "0x00" |
| register "reg_afe_ctrl1" = "0x10" |
| register "reg_afe_ctrl2" = "0x00" |
| register "reg_afe_ctrl3" = "0x00" |
| register "reg_afe_ctrl4" = "0x07" |
| register "reg_afe_ctrl5" = "0x00" |
| register "reg_afe_ctrl6" = "0x00" |
| register "reg_afe_ctrl7" = "0x07" |
| register "reg_afe_ctrl8" = "0x12" |
| register "reg_afe_ctrl9" = "0x0f" |
| register "reg_prox_ctrl0" = "0x12" |
| register "reg_prox_ctrl1" = "0x12" |
| register "reg_prox_ctrl2" = "0x90" |
| register "reg_prox_ctrl3" = "0x60" |
| register "reg_prox_ctrl4" = "0x0c" |
| register "reg_prox_ctrl5" = "0x12" |
| register "reg_prox_ctrl6" = "0x3c" |
| register "reg_prox_ctrl7" = "0x58" |
| register "reg_adv_ctrl0" = "0x00" |
| register "reg_adv_ctrl1" = "0x00" |
| register "reg_adv_ctrl2" = "0x00" |
| register "reg_adv_ctrl3" = "0x00" |
| register "reg_adv_ctrl4" = "0x00" |
| register "reg_adv_ctrl5" = "0x05" |
| register "reg_adv_ctrl6" = "0x00" |
| register "reg_adv_ctrl7" = "0x00" |
| register "reg_adv_ctrl8" = "0x00" |
| register "reg_adv_ctrl9" = "0x00" |
| register "reg_adv_ctrl10" = "0x5c" |
| register "reg_adv_ctrl11" = "0x52" |
| register "reg_adv_ctrl12" = "0xb5" |
| register "reg_adv_ctrl13" = "0x00" |
| register "reg_adv_ctrl14" = "0x80" |
| register "reg_adv_ctrl15" = "0x0c" |
| register "reg_adv_ctrl16" = "0x38" |
| register "reg_adv_ctrl17" = "0x56" |
| register "reg_adv_ctrl18" = "0x33" |
| register "reg_adv_ctrl19" = "0xf0" |
| register "reg_adv_ctrl20" = "0xf0" |
| device i2c 28 on end |
| end |
| end |
| end # chip soc/amd/picasso |
