| chip soc/intel/jasperlake |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI0 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| | before memory is up | |
| #| I2C0 | Trackpad | |
| #| I2C1 | Digitizer | |
| #| I2C2 | Touchscreen | |
| #| I2C3 | Camera | |
| #| I2C4 | Audio | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .gspi[0] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 185, |
| .scl_hcnt = 95, |
| .sda_hold = 40, |
| } |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[4] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 185, |
| .scl_hcnt = 95, |
| .sda_hold = 40, |
| } |
| }, |
| }" |
| |
| # USB Port Configuration |
| register "usb2_ports[2]" = "{ |
| .enable = 1, |
| .ocpin = OC_SKIP, |
| .tx_bias = USB2_BIAS_0MV, |
| .tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON, |
| .pre_emp_bias = USB2_BIAS_28P15MV, |
| .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, |
| }" # Type-A |
| register "usb2_ports[3]" = "{ |
| .enable = 1, |
| .ocpin = OC_SKIP, |
| .tx_bias = USB2_BIAS_0MV, |
| .tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON, |
| .pre_emp_bias = USB2_BIAS_16P9MV, |
| .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, |
| }" # WWAN |
| register "usb2_ports[5]" = "{ |
| .enable = 1, |
| .ocpin = OC_SKIP, |
| .tx_bias = USB2_BIAS_0MV, |
| .tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON, |
| .pre_emp_bias = USB2_BIAS_28P15MV, |
| .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, |
| }" # Camera |
| |
| register "power_limits_config" = "{ |
| .tdp_pl1_override = 6, |
| .tdp_pl2_override = 20, |
| }" |
| |
| register "tcc_offset" = "10" # TCC of 95C |
| |
| device domain 0 on |
| device pci 04.0 on |
| chip drivers/intel/dptf |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 52, 5000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 52, 5000), |
| [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 50, 5000),}" |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 90, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 90, SHUTDOWN), |
| [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 90, SHUTDOWN),}" |
| register "controls.power_limits.pl1" = "{ |
| .min_power = 3500, |
| .max_power = 7000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 28 * MSECS_PER_SEC, |
| .granularity = 250,}" |
| register "controls.power_limits.pl2" = "{ |
| .min_power = 20000, |
| .max_power = 20000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 1000,}" |
| device generic 0 on end |
| end |
| end # SA Thermal device |
| device pci 14.0 on |
| chip drivers/usb/acpi |
| device usb 0.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""UFCamera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "has_power_resource" = "1" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D15)" |
| register "enable_delay_ms" = "20" |
| device usb 2.5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""LTE"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "has_power_resource" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H17)" |
| register "reset_off_delay_ms" = "20" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A10)" |
| register "enable_delay_ms" = "20" |
| device usb 3.3 on end |
| end |
| end |
| end |
| end # USB xHCI |
| device pci 15.0 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""SYNA0A00"" |
| register "generic.desc" = ""SYNA Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_B3_IRQ)" |
| register "generic.wake" = "GPE0_DW0_03" |
| register "generic.probed" = "1" |
| register "hid_desc_reg_offset" = "0x20" |
| device i2c 2c on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""GXTP7288"" |
| register "generic.desc" = ""GXTP Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_B3_IRQ)" |
| register "generic.wake" = "GPE0_DW0_03" |
| register "generic.probed" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 14 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""SPPT2600"" |
| register "generic.desc" = ""SPPT Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_B3_IRQ)" |
| register "generic.wake" = "GPE0_DW0_03" |
| register "generic.probed" = "1" |
| register "hid_desc_reg_offset" = "0x20" |
| device i2c 2a on end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPP_B3_IRQ)" |
| register "wake" = "GPE0_DW0_03" |
| register "probed" = "1" |
| device i2c 15 on end |
| end |
| end #I2C 0 |
| device pci 19.0 on |
| chip drivers/i2c/generic |
| register "hid" = ""10EC5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5682"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on end |
| end |
| end #I2C 4 |
| device pci 1f.3 on |
| chip drivers/generic/alc1015 |
| register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D17)" |
| device generic 0 on end |
| end |
| end # Intel HDA |
| end |
| end |
