src/southbridge/intel/i82801ex/lpc.c

/*
 * (C) 2004 Linux Networx
 */
#include <console/console.h>
#include <device/device.h>
#include <device/pci.h>
#include <device/pci_ids.h>
#include <device/pci_ops.h>
#include <pc80/mc146818rtc.h>
#include <pc80/isa-dma.h>
#include <arch/io.h>
#include <arch/ioapic.h>
#include "i82801ex.h"


#define NMI_OFF 0
#define MAINBOARD_POWER_OFF 0
#define MAINBOARD_POWER_ON  1

#ifndef CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
#define CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
#endif

/**
 * Enable ACPI I/O range.
 *
 * @param dev PCI device with ACPI and PM BAR's
 */
static void i82801ex_enable_acpi(struct device *dev)
{
	u8 gpio_cntl;

	/* Enable ACPI I/O range decode and ACPI power management. */
	pci_write_config8(dev, ACPI_CNTL, ACPI_EN);

	/* Enable the GPIO bar */
	gpio_cntl = pci_read_config8(dev, GPIO_CNTL);
	gpio_cntl |= GPIO_EN;
	pci_write_config8(dev, GPIO_CNTL, gpio_cntl);
}

/**
 * Set miscellanous static southbridge features.
 *
 * @param dev PCI device with I/O APIC configuration registers
 */
static void i82801ex_general_cntl(struct device *dev)
{
	u32 reg32;

	reg32 = pci_read_config32(dev, GEN_CNTL);
	reg32 |= (3 << 7);	/* IOAPIC enable (APIC_EN) */
	reg32 |= (1 << 1);	/* Delayed transaction enable (DTE) */
	pci_write_config32(dev, GEN_CNTL, reg32);
	printk(BIOS_DEBUG, "Southbridge GEN_CNTL 0x%08x\n", reg32);

	reg32 = pci_read_config32(dev, GEN_STS);
	reg32 |= (1<<1);
	pci_write_config32(dev, GEN_STS, reg32);

}

#define SERIRQ_CNTL 0x64
static void i82801ex_enable_serial_irqs(device_t dev)
{
	/* set packet length and toggle silent mode bit */
	pci_write_config8(dev, SERIRQ_CNTL, (1 << 7)|(1 << 6)|((21 - 17) << 2)|(0 << 0));
	pci_write_config8(dev, SERIRQ_CNTL, (1 << 7)|(0 << 6)|((21 - 17) << 2)|(0 << 0));
}

#define PCI_DMA_CFG 0x90
static void i82801ex_pci_dma_cfg(device_t dev)
{
	/* Set PCI DMA CFG to lpc I/F DMA */
	pci_write_config16(dev, PCI_DMA_CFG, 0xfcff);
}

#define LPC_EN 0xe6
static void i82801ex_enable_lpc(device_t dev)
{
        /* lpc i/f enable */
        pci_write_config8(dev, LPC_EN, 0x0d);
}

typedef struct southbridge_intel_i82801ex_config config_t;

static void set_i82801ex_gpio_use_sel(
	device_t dev, struct resource *res, config_t *config)
{
	uint32_t gpio_use_sel, gpio_use_sel2;
	int i;

	gpio_use_sel  = 0x1A003180;
	gpio_use_sel2 = 0x00000007;
	for(i = 0; i < 64; i++) {
		int val;
		switch(config->gpio[i] & ICH5R_GPIO_USE_MASK) {
		case ICH5R_GPIO_USE_AS_NATIVE: val = 0; break;
		case ICH5R_GPIO_USE_AS_GPIO:   val = 1; break;
		default:
			continue;
		}
		/* The caller is responsible for not playing with unimplemented bits */
		if (i < 32) {
			gpio_use_sel  &= ~( 1 << i);
			gpio_use_sel  |= (val << i);
		} else {
			gpio_use_sel2 &= ~( 1 << (i - 32));
			gpio_use_sel2 |= (val << (i - 32));
		}
	}
	outl(gpio_use_sel,  res->base + 0x00);
	outl(gpio_use_sel2, res->base + 0x30);
}

static void set_i82801ex_gpio_direction(
	device_t dev, struct resource *res, config_t *config)
{
	uint32_t gpio_io_sel, gpio_io_sel2;
	int i;

	gpio_io_sel  = 0x0000ffff;
	gpio_io_sel2 = 0x00000300;
	for(i = 0; i < 64; i++) {
		int val;
		switch(config->gpio[i] & ICH5R_GPIO_SEL_MASK) {
		case ICH5R_GPIO_SEL_OUTPUT: val = 0; break;
		case ICH5R_GPIO_SEL_INPUT:  val = 1; break;
		default:
			continue;
		}
		/* The caller is responsible for not playing with unimplemented bits */
		if (i < 32) {
			gpio_io_sel  &= ~( 1 << i);
			gpio_io_sel  |= (val << i);
		} else {
			gpio_io_sel2 &= ~( 1 << (i - 32));
			gpio_io_sel2 |= (val << (i - 32));
		}
	}
	outl(gpio_io_sel,  res->base + 0x04);
	outl(gpio_io_sel2, res->base + 0x34);
}

static void set_i82801ex_gpio_level(
	device_t dev, struct resource *res, config_t *config)
{
	uint32_t gpio_lvl, gpio_lvl2;
	uint32_t gpio_blink;
	int i;

	gpio_lvl   = 0x1b3f0000;
	gpio_blink = 0x00040000;
	gpio_lvl2  = 0x00030207;
	for(i = 0; i < 64; i++) {
		int val, blink;
		switch(config->gpio[i] & ICH5R_GPIO_LVL_MASK) {
		case ICH5R_GPIO_LVL_LOW:   val = 0; blink = 0; break;
		case ICH5R_GPIO_LVL_HIGH:  val = 1; blink = 0; break;
		case ICH5R_GPIO_LVL_BLINK: val = 1; blink = 1; break;
		default:
			continue;
		}
		/* The caller is responsible for not playing with unimplemented bits */
		if (i < 32) {
			gpio_lvl   &= ~(   1 << i);
			gpio_blink &= ~(   1 << i);
			gpio_lvl   |= (  val << i);
			gpio_blink |= (blink << i);
		} else {
			gpio_lvl2  &= ~( 1 << (i - 32));
			gpio_lvl2  |= (val << (i - 32));
		}
	}
	outl(gpio_lvl,   res->base + 0x0c);
	outl(gpio_blink, res->base + 0x18);
	outl(gpio_lvl2,  res->base + 0x38);
}

static void set_i82801ex_gpio_inv(
	device_t dev, struct resource *res, config_t *config)
{
	uint32_t gpio_inv;
	int i;

	gpio_inv   = 0x00000000;
	for(i = 0; i < 32; i++) {
		int val;
		switch(config->gpio[i] & ICH5R_GPIO_INV_MASK) {
		case ICH5R_GPIO_INV_OFF: val = 0; break;
		case ICH5R_GPIO_INV_ON:  val = 1; break;
		default:
			continue;
		}
		gpio_inv &= ~( 1 << i);
		gpio_inv |= (val << i);
	}
	outl(gpio_inv,   res->base + 0x2c);
}

static void i82801ex_pirq_init(device_t dev)
{
	config_t *config;

	/* Get the chip configuration */
	config = dev->chip_info;

	if(config->pirq_a_d) {
		pci_write_config32(dev, 0x60, config->pirq_a_d);
	}
	if(config->pirq_e_h) {
		pci_write_config32(dev, 0x68, config->pirq_e_h);
	}
}


static void i82801ex_gpio_init(device_t dev)
{
	struct resource *res;
	config_t *config;

	/* Skip if I don't have any configuration */
	if (!dev->chip_info) {
		return;
	}
	/* The programmer is responsible for ensuring
	 * a valid gpio configuration.
	 */

	/* Get the chip configuration */
	config = dev->chip_info;
	/* Find the GPIO bar */
	res = find_resource(dev, GPIO_BASE);
	if (!res) {
		return;
	}

	/* Set the use selects */
	set_i82801ex_gpio_use_sel(dev, res, config);

	/* Set the IO direction */
	set_i82801ex_gpio_direction(dev, res, config);

	/* Setup the input inverters */
	set_i82801ex_gpio_inv(dev, res, config);

	/* Set the value on the GPIO output pins */
	set_i82801ex_gpio_level(dev, res, config);

}

static void enable_hpet(struct device *dev)
{
	const unsigned long hpet_address = 0xfed00000;

	uint32_t dword;
	uint32_t code = (0 & 0x3);

	dword = pci_read_config32(dev, GEN_CNTL);
	dword |= (1 << 17); /* enable hpet */

	/* Bits [16:15]  Memory Address Range
	 *	    00   FED0_0000h - FED0_03FFh
	 *	    01   FED0_1000h - FED0_13FFh
	 *	    10   FED0_2000h - FED0_23FFh
	 *	    11   FED0_3000h - FED0_33FFh
	 */

	dword &= ~(3 << 15); /* clear it */
	dword |= (code<<15);
	pci_write_config32(dev, GEN_CNTL, dword);

	printk(BIOS_DEBUG, "enabling HPET @0x%lx\n", hpet_address | (code <<12) );
}

static void lpc_init(struct device *dev)
{
	uint8_t byte;
	int pwr_on=CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL;

	i82801ex_general_cntl(dev);

	/* IO APIC initialization. */
	setup_ioapic(IO_APIC_ADDR, 0); // Don't rename IO APIC ID.

	i82801ex_enable_serial_irqs(dev);

	i82801ex_pci_dma_cfg(dev);

	i82801ex_enable_lpc(dev);

	/* Clear SATA to non raid */
	pci_write_config8(dev, 0xae, 0x00);

        get_option(&pwr_on, "power_on_after_fail");
	byte = pci_read_config8(dev, 0xa4);
	byte &= 0xfe;
	if (!pwr_on) {
		byte |= 1;
	}
	pci_write_config8(dev, 0xa4, byte);
	printk(BIOS_INFO, "set power %s after power fail\n", pwr_on?"on":"off");

	/* Set up the PIRQ */
	i82801ex_pirq_init(dev);

	/* Set the state of the gpio lines */
	i82801ex_gpio_init(dev);

	/* Initialize the real time clock */
	rtc_init(0);

	/* Initialize isa dma */
	isa_dma_init();

	/* Disable IDE (needed when sata is enabled) */
	pci_write_config8(dev, 0xf2, 0x60);

	enable_hpet(dev);
}

static void i82801ex_lpc_read_resources(device_t dev)
{
	struct resource *res;

	/* Get the normal PCI resources of this device. */
	pci_dev_read_resources(dev);

	/* Add the ACPI BAR */
	res = pci_get_resource(dev, PMBASE);

	/* Add the GPIO BAR */
	res = pci_get_resource(dev, GPIO_BASE);

	/* Add an extra subtractive resource for both memory and I/O. */
	res = new_resource(dev, IOINDEX_SUBTRACTIVE(0, 0));
	res->base = 0;
	res->size = 0x1000;
	res->flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE |
		     IORESOURCE_ASSIGNED | IORESOURCE_FIXED;

	res = new_resource(dev, IOINDEX_SUBTRACTIVE(1, 0));
	res->base = 0xff800000;
	res->size = 0x00800000; /* 8 MB for flash */
	res->flags = IORESOURCE_MEM | IORESOURCE_SUBTRACTIVE |
		     IORESOURCE_ASSIGNED | IORESOURCE_FIXED;

	res = new_resource(dev, 3); /* IOAPIC */
	res->base = IO_APIC_ADDR;
	res->size = 0x00001000;
	res->flags = IORESOURCE_MEM | IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
}

static void i82801ex_lpc_enable_resources(device_t dev)
{
	/* Enable the normal PCI resources. */
	pci_dev_enable_resources(dev);

	/* Enable ACPI and GPIO BARs. */
	i82801ex_enable_acpi(dev);
}

static struct pci_operations lops_pci = {
	.set_subsystem = 0,
};

static struct device_operations lpc_ops  = {
	.read_resources   = i82801ex_lpc_read_resources,
	.set_resources    = pci_dev_set_resources,
	.enable_resources = i82801ex_lpc_enable_resources,
	.init             = lpc_init,
	.scan_bus         = scan_static_bus,
	.enable           = i82801ex_enable,
	.ops_pci          = &lops_pci,
};

static const struct pci_driver lpc_driver __pci_driver = {
	.ops    = &lpc_ops,
	.vendor = PCI_VENDOR_ID_INTEL,
	.device = PCI_DEVICE_ID_INTEL_82801ER_LPC,
};