src/mainboard/google/rush_ryu/bootblock.c

/*
 * This file is part of the coreboot project.
 *
 * Copyright 2014 Google Inc.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; version 2 of the License.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
 */

#include <arch/io.h>
#include <console/console.h>
#include <device/i2c.h>
#include <soc/addressmap.h>
#include <soc/bootblock.h>
#include <soc/clock.h>
#include <soc/funitcfg.h>
#include <soc/padconfig.h>
#include <soc/nvidia/tegra/i2c.h>
#include <soc/nvidia/tegra132/clk_rst.h>

#include "pmic.h"

static const struct pad_config uart_console_pads[] = {
	/* UARTA: tx and rx. */
	PAD_CFG_SFIO(KB_ROW9, PINMUX_PULL_NONE, UA3),
	PAD_CFG_SFIO(KB_ROW10, PINMUX_INPUT_ENABLE | PINMUX_PULL_UP, UA3),
	/*
	 * Disable UART2 pads as they are default connected to UARTA controller.
	 */
	PAD_CFG_UNUSED(UART2_RXD),
	PAD_CFG_UNUSED(UART2_TXD),
	PAD_CFG_UNUSED(UART2_RTS_N),
	PAD_CFG_UNUSED(UART2_CTS_N),
};

static const struct pad_config pmic_pads[] = {
	PAD_CFG_SFIO(PWR_I2C_SCL, PINMUX_INPUT_ENABLE, I2CPMU),
	PAD_CFG_SFIO(PWR_I2C_SDA, PINMUX_INPUT_ENABLE, I2CPMU),
};

static const struct pad_config spiflash_pads[] = {
	/* mosi, miso, clk, cs0  */
	PAD_CFG_SFIO(GPIO_PG6, PINMUX_INPUT_ENABLE | PINMUX_PULL_UP, SPI4),
	PAD_CFG_SFIO(GPIO_PG7, PINMUX_INPUT_ENABLE | PINMUX_PULL_UP, SPI4),
	PAD_CFG_SFIO(GPIO_PG5, PINMUX_INPUT_ENABLE, SPI4),
	PAD_CFG_SFIO(GPIO_PI3, PINMUX_INPUT_ENABLE, SPI4),
};

static const struct funit_cfg funits[] = {
	/* PMIC on I2C5 (PWR_I2C* pads) at 400kHz. */
	FUNIT_CFG(I2C5, PLLP, 400, pmic_pads, ARRAY_SIZE(pmic_pads)),
	/* SPI flash at 33MHz on SPI4 controller. */
	FUNIT_CFG(SBC4, PLLP, 33333, spiflash_pads, ARRAY_SIZE(spiflash_pads)),
};

void bootblock_mainboard_early_init(void)
{
	soc_configure_pads(uart_console_pads, ARRAY_SIZE(uart_console_pads));
}

static void set_clock_sources(void)
{
	/* UARTA gets PLLP, deactivate CLK_UART_DIV_OVERRIDE */
	writel(PLLP << CLK_SOURCE_SHIFT, CLK_RST_REG(clk_src_uarta));
}

static const struct pad_config padcfgs[] = {
	/* Board build id bits 1:0 */
	PAD_CFG_GPIO_INPUT(KB_COL4, PINMUX_PULL_NONE),
	PAD_CFG_GPIO_INPUT(KB_COL3, PINMUX_PULL_NONE),
};

void bootblock_mainboard_init(void)
{
	set_clock_sources();

	/* Set up controllers and pads to load romstage. */
	soc_configure_funits(funits, ARRAY_SIZE(funits));
	soc_configure_pads(padcfgs, ARRAY_SIZE(padcfgs));

	i2c_init(I2CPWR_BUS);
	pmic_init(I2CPWR_BUS);
}