From d50b1a10adccff5c2154517cc9c8adfd249f4339 Mon Sep 17 00:00:00 2001
From: Roy Luo <royluo@google.com>
Date: Tue, 2 Jul 2019 13:47:24 -0700
Subject: [PATCH] BACKPORT: sync enum nl80211_commands with kernel v5.2

The following upstream commits add support of
nl80211 command NL80211_CMD_PROBE_MESH_LINK:
5ab92e7fe49ad74293b50fb9e6f25be5521e2f68
060167729a78d626abaee1a0ebb64b252374426e
8828f81ad4a2f4e89ebe6e7793c06ed767c31d53

This patch sync the enum nl80211_commands with
kernel v5.2 in order to use the new nl80211 command.

Signed-off-by: Roy Luo <royluo@google.com>
---
 include/uapi/linux/nl80211.h | 119+++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 119 insertions(+)

diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h
index f840536..79e9734 100644
--- a/include/uapi/linux/nl80211.h
+++ b/include/uapi/linux/nl80211.h
@@ -982,6 +982,103 @@
  * @NL80211_CMD_DEL_PMK: For offloaded 4-Way handshake, delete the previously
  *	configured PMK for the authenticator address identified by
  *	&NL80211_ATTR_MAC.
+ * @NL80211_CMD_PORT_AUTHORIZED: An event that indicates that the 4 way
+ *	handshake was completed successfully by the driver. The BSSID is
+ *	specified with %NL80211_ATTR_MAC. Drivers that support 4 way handshake
+ *	offload should send this event after indicating 802.11 association with
+ *	%NL80211_CMD_CONNECT or %NL80211_CMD_ROAM. If the 4 way handshake failed
+ *	%NL80211_CMD_DISCONNECT should be indicated instead.
+ *
+ * @NL80211_CMD_CONTROL_PORT_FRAME: Control Port (e.g. PAE) frame TX request
+ *	and RX notification.  This command is used both as a request to transmit
+ *	a control port frame and as a notification that a control port frame
+ *	has been received. %NL80211_ATTR_FRAME is used to specify the
+ *	frame contents.  The frame is the raw EAPoL data, without ethernet or
+ *	802.11 headers.
+ *	When used as an event indication %NL80211_ATTR_CONTROL_PORT_ETHERTYPE,
+ *	%NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT and %NL80211_ATTR_MAC are added
+ *	indicating the protocol type of the received frame; whether the frame
+ *	was received unencrypted and the MAC address of the peer respectively.
+ *
+ * @NL80211_CMD_RELOAD_REGDB: Request that the regdb firmware file is reloaded.
+ *
+ * @NL80211_CMD_EXTERNAL_AUTH: This interface is exclusively defined for host
+ *	drivers that do not define separate commands for authentication and
+ *	association, but rely on user space for the authentication to happen.
+ *	This interface acts both as the event request (driver to user space)
+ *	to trigger the authentication and command response (userspace to
+ *	driver) to indicate the authentication status.
+ *
+ *	User space uses the %NL80211_CMD_CONNECT command to the host driver to
+ *	trigger a connection. The host driver selects a BSS and further uses
+ *	this interface to offload only the authentication part to the user
+ *	space. Authentication frames are passed between the driver and user
+ *	space through the %NL80211_CMD_FRAME interface. Host driver proceeds
+ *	further with the association after getting successful authentication
+ *	status. User space indicates the authentication status through
+ *	%NL80211_ATTR_STATUS_CODE attribute in %NL80211_CMD_EXTERNAL_AUTH
+ *	command interface.
+ *
+ *	Host driver reports this status on an authentication failure to the
+ *	user space through the connect result as the user space would have
+ *	initiated the connection through the connect request.
+ *
+ * @NL80211_CMD_STA_OPMODE_CHANGED: An event that notify station's
+ *	ht opmode or vht opmode changes using any of %NL80211_ATTR_SMPS_MODE,
+ *	%NL80211_ATTR_CHANNEL_WIDTH,%NL80211_ATTR_NSS attributes with its
+ *	address(specified in %NL80211_ATTR_MAC).
+ *
+ * @NL80211_CMD_GET_FTM_RESPONDER_STATS: Retrieve FTM responder statistics, in
+ *	the %NL80211_ATTR_FTM_RESPONDER_STATS attribute.
+ *
+ * @NL80211_CMD_PEER_MEASUREMENT_START: start a (set of) peer measurement(s)
+ *	with the given parameters, which are encapsulated in the nested
+ *	%NL80211_ATTR_PEER_MEASUREMENTS attribute. Optionally, MAC address
+ *	randomization may be enabled and configured by specifying the
+ *	%NL80211_ATTR_MAC and %NL80211_ATTR_MAC_MASK attributes.
+ *	If a timeout is requested, use the %NL80211_ATTR_TIMEOUT attribute.
+ *	A u64 cookie for further %NL80211_ATTR_COOKIE use is is returned in
+ *	the netlink extended ack message.
+ *
+ *	To cancel a measurement, close the socket that requested it.
+ *
+ *	Measurement results are reported to the socket that requested the
+ *	measurement using @NL80211_CMD_PEER_MEASUREMENT_RESULT when they
+ *	become available, so applications must ensure a large enough socket
+ *	buffer size.
+ *
+ *	Depending on driver support it may or may not be possible to start
+ *	multiple concurrent measurements.
+ * @NL80211_CMD_PEER_MEASUREMENT_RESULT: This command number is used for the
+ *	result notification from the driver to the requesting socket.
+ * @NL80211_CMD_PEER_MEASUREMENT_COMPLETE: Notification only, indicating that
+ *	the measurement completed, using the measurement cookie
+ *	(%NL80211_ATTR_COOKIE).
+ *
+ * @NL80211_CMD_NOTIFY_RADAR: Notify the kernel that a radar signal was
+ *	detected and reported by a neighboring device on the channel
+ *	indicated by %NL80211_ATTR_WIPHY_FREQ and other attributes
+ *	determining the width and type.
+ *
+ * @NL80211_CMD_UPDATE_OWE_INFO: This interface allows the host driver to
+ *	offload OWE processing to user space. This intends to support
+ *	OWE AKM by the host drivers that implement SME but rely
+ *	on the user space for the cryptographic/DH IE processing in AP mode.
+ *
+ * @NL80211_CMD_PROBE_MESH_LINK: The requirement for mesh link metric
+ *	refreshing, is that from one mesh point we be able to send some data
+ *	frames to other mesh points which are not currently selected as a
+ *	primary traffic path, but which are only 1 hop away. The absence of
+ *	the primary path to the chosen node makes it necessary to apply some
+ *	form of marking on a chosen packet stream so that the packets can be
+ *	properly steered to the selected node for testing, and not by the
+ *	regular mesh path lookup. Further, the packets must be of type data
+ *	so that the rate control (often embedded in firmware) is used for
+ *	rate selection.
+ *
+ *	Here attribute %NL80211_ATTR_MAC is used to specify connected mesh
+ *	peer MAC address and %NL80211_ATTR_FRAME is used to specify the frame
+ *	content. The frame is ethernet data.
  *
  * @NL80211_CMD_MAX: highest used command number
  * @__NL80211_CMD_AFTER_LAST: internal use
@@ -1185,6 +1200,28 @@ enum nl80211_commands {
 	NL80211_CMD_SET_PMK,
 	NL80211_CMD_DEL_PMK,
 
+	NL80211_CMD_PORT_AUTHORIZED,
+
+	NL80211_CMD_RELOAD_REGDB,
+
+	NL80211_CMD_EXTERNAL_AUTH,
+
+	NL80211_CMD_STA_OPMODE_CHANGED,
+
+	NL80211_CMD_CONTROL_PORT_FRAME,
+
+	NL80211_CMD_GET_FTM_RESPONDER_STATS,
+
+	NL80211_CMD_PEER_MEASUREMENT_START,
+	NL80211_CMD_PEER_MEASUREMENT_RESULT,
+	NL80211_CMD_PEER_MEASUREMENT_COMPLETE,
+
+	NL80211_CMD_NOTIFY_RADAR,
+
+	NL80211_CMD_UPDATE_OWE_INFO,
+
+	NL80211_CMD_PROBE_MESH_LINK,
+
 	/* add new commands above here */
 
 	/* used to define NL80211_CMD_MAX below */
--
2.22.0.657.g960e92d24f-goog