| # SPDX-License-Identifier: GPL-2.0-only |
| menu "CAN Device Drivers" |
| |
| config CAN_VCAN |
| tristate "Virtual Local CAN Interface (vcan)" |
| ---help--- |
| Similar to the network loopback devices, vcan offers a |
| virtual local CAN interface. |
| |
| This driver can also be built as a module. If so, the module |
| will be called vcan. |
| |
| config CAN_VXCAN |
| tristate "Virtual CAN Tunnel (vxcan)" |
| ---help--- |
| Similar to the virtual ethernet driver veth, vxcan implements a |
| local CAN traffic tunnel between two virtual CAN network devices. |
| When creating a vxcan, two vxcan devices are created as pair. |
| When one end receives the packet it appears on its pair and vice |
| versa. The vxcan can be used for cross namespace communication. |
| |
| In opposite to vcan loopback devices the vxcan only forwards CAN |
| frames to its pair and does *not* provide a local echo of sent |
| CAN frames. To disable a potential echo in af_can.c the vxcan driver |
| announces IFF_ECHO in the interface flags. To have a clean start |
| in each namespace the CAN GW hop counter is set to zero. |
| |
| This driver can also be built as a module. If so, the module |
| will be called vxcan. |
| |
| config CAN_SLCAN |
| tristate "Serial / USB serial CAN Adaptors (slcan)" |
| depends on TTY |
| ---help--- |
| CAN driver for several 'low cost' CAN interfaces that are attached |
| via serial lines or via USB-to-serial adapters using the LAWICEL |
| ASCII protocol. The driver implements the tty linediscipline N_SLCAN. |
| |
| As only the sending and receiving of CAN frames is implemented, this |
| driver should work with the (serial/USB) CAN hardware from: |
| www.canusb.com / www.can232.com / www.mictronics.de / www.canhack.de |
| |
| Userspace tools to attach the SLCAN line discipline (slcan_attach, |
| slcand) can be found in the can-utils at the SocketCAN SVN, see |
| http://developer.berlios.de/projects/socketcan for details. |
| |
| The slcan driver supports up to 10 CAN netdevices by default which |
| can be changed by the 'maxdev=xx' module option. This driver can |
| also be built as a module. If so, the module will be called slcan. |
| |
| config CAN_DEV |
| tristate "Platform CAN drivers with Netlink support" |
| default y |
| ---help--- |
| Enables the common framework for platform CAN drivers with Netlink |
| support. This is the standard library for CAN drivers. |
| If unsure, say Y. |
| |
| if CAN_DEV |
| |
| config CAN_CALC_BITTIMING |
| bool "CAN bit-timing calculation" |
| default y |
| ---help--- |
| If enabled, CAN bit-timing parameters will be calculated for the |
| bit-rate specified via Netlink argument "bitrate" when the device |
| get started. This works fine for the most common CAN controllers |
| with standard bit-rates but may fail for exotic bit-rates or CAN |
| source clock frequencies. Disabling saves some space, but then the |
| bit-timing parameters must be specified directly using the Netlink |
| arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" and "sjw". |
| If unsure, say Y. |
| |
| config CAN_LEDS |
| bool "Enable LED triggers for Netlink based drivers" |
| depends on LEDS_CLASS |
| # The netdev trigger (LEDS_TRIGGER_NETDEV) should be able to do |
| # everything that this driver is doing. This is marked as broken |
| # because it uses stuff that is intended to be changed or removed. |
| # Please consider switching to the netdev trigger and confirm it |
| # fulfills your needs instead of fixing this driver. |
| depends on BROKEN |
| select LEDS_TRIGGERS |
| ---help--- |
| This option adds two LED triggers for packet receive and transmit |
| events on each supported CAN device. |
| |
| Say Y here if you are working on a system with led-class supported |
| LEDs and you want to use them as canbus activity indicators. |
| |
| config CAN_AT91 |
| tristate "Atmel AT91 onchip CAN controller" |
| depends on (ARCH_AT91 || COMPILE_TEST) && HAS_IOMEM |
| ---help--- |
| This is a driver for the SoC CAN controller in Atmel's AT91SAM9263 |
| and AT91SAM9X5 processors. |
| |
| config CAN_FLEXCAN |
| tristate "Support for Freescale FLEXCAN based chips" |
| depends on OF && HAS_IOMEM |
| ---help--- |
| Say Y here if you want to support for Freescale FlexCAN. |
| |
| config CAN_GRCAN |
| tristate "Aeroflex Gaisler GRCAN and GRHCAN CAN devices" |
| depends on OF && HAS_DMA |
| ---help--- |
| Say Y here if you want to use Aeroflex Gaisler GRCAN or GRHCAN. |
| Note that the driver supports little endian, even though little |
| endian syntheses of the cores would need some modifications on |
| the hardware level to work. |
| |
| config CAN_JANZ_ICAN3 |
| tristate "Janz VMOD-ICAN3 Intelligent CAN controller" |
| depends on MFD_JANZ_CMODIO |
| ---help--- |
| Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which |
| connects to a MODULbus carrier board. |
| |
| This driver can also be built as a module. If so, the module will be |
| called janz-ican3.ko. |
| |
| config CAN_KVASER_PCIEFD |
| depends on PCI |
| tristate "Kvaser PCIe FD cards" |
| select CRC32 |
| help |
| This is a driver for the Kvaser PCI Express CAN FD family. |
| |
| Supported devices: |
| Kvaser PCIEcan 4xHS |
| Kvaser PCIEcan 2xHS v2 |
| Kvaser PCIEcan HS v2 |
| Kvaser Mini PCI Express HS v2 |
| Kvaser Mini PCI Express 2xHS v2 |
| |
| config CAN_SUN4I |
| tristate "Allwinner A10 CAN controller" |
| depends on MACH_SUN4I || MACH_SUN7I || COMPILE_TEST |
| ---help--- |
| Say Y here if you want to use CAN controller found on Allwinner |
| A10/A20 SoCs. |
| |
| To compile this driver as a module, choose M here: the module will |
| be called sun4i_can. |
| |
| config CAN_TI_HECC |
| depends on ARM |
| tristate "TI High End CAN Controller" |
| ---help--- |
| Driver for TI HECC (High End CAN Controller) module found on many |
| TI devices. The device specifications are available from www.ti.com |
| |
| config CAN_XILINXCAN |
| tristate "Xilinx CAN" |
| depends on ARCH_ZYNQ || ARM64 || MICROBLAZE || COMPILE_TEST |
| depends on COMMON_CLK && HAS_IOMEM |
| ---help--- |
| Xilinx CAN driver. This driver supports both soft AXI CAN IP and |
| Zynq CANPS IP. |
| |
| config PCH_CAN |
| tristate "Intel EG20T PCH CAN controller" |
| depends on PCI && (X86_32 || COMPILE_TEST) |
| ---help--- |
| This driver is for PCH CAN of Topcliff (Intel EG20T PCH) which |
| is an IOH for x86 embedded processor (Intel Atom E6xx series). |
| This driver can access CAN bus. |
| |
| source "drivers/net/can/c_can/Kconfig" |
| source "drivers/net/can/cc770/Kconfig" |
| source "drivers/net/can/ifi_canfd/Kconfig" |
| source "drivers/net/can/m_can/Kconfig" |
| source "drivers/net/can/mscan/Kconfig" |
| source "drivers/net/can/peak_canfd/Kconfig" |
| source "drivers/net/can/rcar/Kconfig" |
| source "drivers/net/can/sja1000/Kconfig" |
| source "drivers/net/can/softing/Kconfig" |
| source "drivers/net/can/spi/Kconfig" |
| source "drivers/net/can/usb/Kconfig" |
| |
| endif |
| |
| config CAN_DEBUG_DEVICES |
| bool "CAN devices debugging messages" |
| ---help--- |
| Say Y here if you want the CAN device drivers to produce a bunch of |
| debug messages to the system log. Select this if you are having |
| a problem with CAN support and want to see more of what is going |
| on. |
| |
| endmenu |