/* SPDX-License-Identifier: GPL-2.0 */
/******************************************************************************
 *
 * Copyright(c) 2007 - 2011 Realtek Corporation. All rights reserved.
 *
 ******************************************************************************/
#ifndef __IEEE80211_H
#define __IEEE80211_H

#include <osdep_service.h>
#include <drv_types.h>
#include "wifi.h"
#include <linux/wireless.h>

#ifdef CONFIG_88EU_AP_MODE

#define RTL_IOCTL_HOSTAPD (SIOCIWFIRSTPRIV + 28)

/* RTL871X_IOCTL_HOSTAPD ioctl() cmd: */
enum {
	RTL871X_HOSTAPD_FLUSH = 1,
	RTL871X_HOSTAPD_ADD_STA = 2,
	RTL871X_HOSTAPD_REMOVE_STA = 3,
	RTL871X_HOSTAPD_GET_INFO_STA = 4,
	/* REMOVED: PRISM2_HOSTAPD_RESET_TXEXC_STA = 5, */
	RTL871X_HOSTAPD_GET_WPAIE_STA = 5,
	RTL871X_SET_ENCRYPTION = 6,
	RTL871X_GET_ENCRYPTION = 7,
	RTL871X_HOSTAPD_SET_FLAGS_STA = 8,
	RTL871X_HOSTAPD_GET_RID = 9,
	RTL871X_HOSTAPD_SET_RID = 10,
	RTL871X_HOSTAPD_SET_ASSOC_AP_ADDR = 11,
	RTL871X_HOSTAPD_SET_GENERIC_ELEMENT = 12,
	RTL871X_HOSTAPD_MLME = 13,
	RTL871X_HOSTAPD_SCAN_REQ = 14,
	RTL871X_HOSTAPD_STA_CLEAR_STATS = 15,
	RTL871X_HOSTAPD_SET_BEACON = 16,
	RTL871X_HOSTAPD_SET_WPS_BEACON = 17,
	RTL871X_HOSTAPD_SET_WPS_PROBE_RESP = 18,
	RTL871X_HOSTAPD_SET_WPS_ASSOC_RESP = 19,
	RTL871X_HOSTAPD_SET_HIDDEN_SSID = 20,
	RTL871X_HOSTAPD_SET_MACADDR_ACL = 21,
	RTL871X_HOSTAPD_ACL_ADD_STA = 22,
	RTL871X_HOSTAPD_ACL_REMOVE_STA = 23,
};

/* STA flags */
#define WLAN_STA_AUTH BIT(0)
#define WLAN_STA_ASSOC BIT(1)
#define WLAN_STA_PS BIT(2)
#define WLAN_STA_TIM BIT(3)
#define WLAN_STA_PERM BIT(4)
#define WLAN_STA_AUTHORIZED BIT(5)
#define WLAN_STA_PENDING_POLL BIT(6) /* pending activity poll not ACKed */
#define WLAN_STA_SHORT_PREAMBLE BIT(7)
#define WLAN_STA_PREAUTH BIT(8)
#define WLAN_STA_WME BIT(9)
#define WLAN_STA_MFP BIT(10)
#define WLAN_STA_HT BIT(11)
#define WLAN_STA_WPS BIT(12)
#define WLAN_STA_MAYBE_WPS BIT(13)
#define WLAN_STA_NONERP BIT(31)

#endif

#define IEEE_CMD_SET_WPA_PARAM			1
#define IEEE_CMD_SET_WPA_IE				2
#define IEEE_CMD_SET_ENCRYPTION			3
#define IEEE_CMD_MLME						4

#define IEEE_PARAM_WPA_ENABLED				1
#define IEEE_PARAM_TKIP_COUNTERMEASURES		2
#define IEEE_PARAM_DROP_UNENCRYPTED			3
#define IEEE_PARAM_PRIVACY_INVOKED			4
#define IEEE_PARAM_AUTH_ALGS					5
#define IEEE_PARAM_IEEE_802_1X				6
#define IEEE_PARAM_WPAX_SELECT				7

#define AUTH_ALG_OPEN_SYSTEM			0x1
#define AUTH_ALG_SHARED_KEY			0x2
#define AUTH_ALG_LEAP				0x00000004

#define IEEE_MLME_STA_DEAUTH				1
#define IEEE_MLME_STA_DISASSOC			2

#define IEEE_CRYPT_ERR_UNKNOWN_ALG			2
#define IEEE_CRYPT_ERR_UNKNOWN_ADDR			3
#define IEEE_CRYPT_ERR_CRYPT_INIT_FAILED		4
#define IEEE_CRYPT_ERR_KEY_SET_FAILED			5
#define IEEE_CRYPT_ERR_TX_KEY_SET_FAILED		6
#define IEEE_CRYPT_ERR_CARD_CONF_FAILED		7

#define	IEEE_CRYPT_ALG_NAME_LEN			16

#define WPA_CIPHER_NONE		BIT(0)
#define WPA_CIPHER_WEP40	BIT(1)
#define WPA_CIPHER_WEP104 BIT(2)
#define WPA_CIPHER_TKIP		BIT(3)
#define WPA_CIPHER_CCMP		BIT(4)

#define WPA_SELECTOR_LEN 4
extern u8 RTW_WPA_OUI_TYPE[];
extern u8 WPA_AUTH_KEY_MGMT_NONE[];
extern u8 WPA_AUTH_KEY_MGMT_UNSPEC_802_1X[];
extern u8 WPA_AUTH_KEY_MGMT_PSK_OVER_802_1X[];
extern u8 WPA_CIPHER_SUITE_NONE[];
extern u8 WPA_CIPHER_SUITE_WEP40[];
extern u8 WPA_CIPHER_SUITE_TKIP[];
extern u8 WPA_CIPHER_SUITE_WRAP[];
extern u8 WPA_CIPHER_SUITE_CCMP[];
extern u8 WPA_CIPHER_SUITE_WEP104[];

#define RSN_HEADER_LEN 4
#define RSN_SELECTOR_LEN 4

extern u16 RSN_VERSION_BSD;
extern u8 RSN_AUTH_KEY_MGMT_UNSPEC_802_1X[];
extern u8 RSN_AUTH_KEY_MGMT_PSK_OVER_802_1X[];
extern u8 RSN_CIPHER_SUITE_NONE[];
extern u8 RSN_CIPHER_SUITE_WEP40[];
extern u8 RSN_CIPHER_SUITE_TKIP[];
extern u8 RSN_CIPHER_SUITE_WRAP[];
extern u8 RSN_CIPHER_SUITE_CCMP[];
extern u8 RSN_CIPHER_SUITE_WEP104[];

enum ratr_table_mode {
	RATR_INX_WIRELESS_NGB = 0,	/*  BGN 40 Mhz 2SS 1SS */
	RATR_INX_WIRELESS_NG = 1,	/*  GN or N */
	RATR_INX_WIRELESS_NB = 2,	/*  BGN 20 Mhz 2SS 1SS  or BN */
	RATR_INX_WIRELESS_N = 3,
	RATR_INX_WIRELESS_GB = 4,
	RATR_INX_WIRELESS_G = 5,
	RATR_INX_WIRELESS_B = 6,
	RATR_INX_WIRELESS_MC = 7,
	RATR_INX_WIRELESS_AC_N = 8,
};

enum NETWORK_TYPE {
	WIRELESS_INVALID = 0,
	/* Sub-Element */
	WIRELESS_11B = BIT(0), /* tx:cck only, rx:cck only, hw: cck */
	WIRELESS_11G = BIT(1), /* tx:ofdm only, rx:ofdm & cck, hw:cck & ofdm*/
	WIRELESS_11A = BIT(2), /* tx:ofdm only, rx: ofdm only, hw:ofdm only */
	WIRELESS_11_24N = BIT(3), /* tx:MCS only, rx:MCS & cck, hw:MCS & cck */
	WIRELESS_11_5N = BIT(4), /* tx:MCS only, rx:MCS & ofdm, hw:ofdm only */
	WIRELESS_AC		= BIT(6),

	/* Combination */
	/*  tx: cck & ofdm, rx: cck & ofdm & MCS, hw: cck & ofdm */
	WIRELESS_11BG = (WIRELESS_11B | WIRELESS_11G),
	/*  tx: ofdm & MCS, rx: ofdm & cck & MCS, hw: cck & ofdm */
	WIRELESS_11G_24N = (WIRELESS_11G | WIRELESS_11_24N),
	/*  tx: ofdm & MCS, rx: ofdm & MCS, hw: ofdm only */
	WIRELESS_11A_5N = (WIRELESS_11A | WIRELESS_11_5N),
	/*  tx: ofdm & cck & MCS, rx: ofdm & cck & MCS, hw: ofdm & cck */
	WIRELESS_11BG_24N = (WIRELESS_11B | WIRELESS_11G | WIRELESS_11_24N),
	/*  tx: ofdm & MCS, rx: ofdm & MCS, hw: ofdm only */
	WIRELESS_11AGN = (WIRELESS_11A | WIRELESS_11G | WIRELESS_11_24N |
			  WIRELESS_11_5N),
	WIRELESS_11ABGN = (WIRELESS_11A | WIRELESS_11B | WIRELESS_11G |
			   WIRELESS_11_24N | WIRELESS_11_5N),
};

#define SUPPORTED_24G_NETTYPE_MSK				\
	 (WIRELESS_11B | WIRELESS_11G | WIRELESS_11_24N)
#define SUPPORTED_5G_NETTYPE_MSK				\
	 (WIRELESS_11A | WIRELESS_11_5N)

#define IsSupported24G(NetType)					\
	((NetType) & SUPPORTED_24G_NETTYPE_MSK ? true : false)
#define IsSupported5G(NetType)					\
	((NetType) & SUPPORTED_5G_NETTYPE_MSK ? true : false)

#define IsEnableHWCCK(NetType)					\
	IsSupported24G(NetType)
#define IsEnableHWOFDM(NetType)					\
	((NetType) & (WIRELESS_11G | WIRELESS_11_24N |		\
	 SUPPORTED_5G_NETTYPE_MSK) ? true : false)

#define IsSupportedRxCCK(NetType) IsEnableHWCCK(NetType)
#define IsSupportedRxOFDM(NetType) IsEnableHWOFDM(NetType)
#define IsSupportedRxMCS(NetType) IsEnableHWOFDM(NetType)

#define IsSupportedTxCCK(NetType)				\
	((NetType) & (WIRELESS_11B) ? true : false)
#define IsSupportedTxOFDM(NetType)				\
	((NetType) & (WIRELESS_11G | WIRELESS_11A) ? true : false)
#define IsSupportedTxMCS(NetType)				\
	((NetType) & (WIRELESS_11_24N | WIRELESS_11_5N) ? true : false)

struct ieee_param {
	u32 cmd;
	u8 sta_addr[ETH_ALEN];
	union {
		struct {
			u8 name;
			u32 value;
		} wpa_param;
		struct {
			u32 len;
			u8 reserved[32];
			u8 data[0];
		} wpa_ie;
		struct {
			int command;
			int reason_code;
		} mlme;
		struct {
			u8 alg[IEEE_CRYPT_ALG_NAME_LEN];
			u8 set_tx;
			u32 err;
			u8 idx;
			u8 seq[8]; /* sequence counter (set: RX, get: TX) */
			u16 key_len;
			u8 key[0];
		} crypt;
#ifdef CONFIG_88EU_AP_MODE
		struct {
			u16 aid;
			u16 capability;
			int flags;
			u8 tx_supp_rates[16];
			struct ieee80211_ht_cap ht_cap;
		} add_sta;
		struct {
			u8	reserved[2];/* for set max_num_sta */
			u8	buf[0];
		} bcn_ie;
#endif

	} u;
};

#ifdef CONFIG_88EU_AP_MODE
struct ieee_param_ex {
	u32 cmd;
	u8 sta_addr[ETH_ALEN];
	u8 data[0];
};

struct sta_data {
	u16 aid;
	u16 capability;
	int flags;
	u32 sta_set;
	u8 tx_supp_rates[16];
	u32 tx_supp_rates_len;
	struct ieee80211_ht_cap ht_cap;
	u64	rx_pkts;
	u64	rx_bytes;
	u64	rx_drops;
	u64	tx_pkts;
	u64	tx_bytes;
	u64	tx_drops;
};
#endif

#define IEEE80211_DATA_LEN		2304
/* Maximum size for the MA-UNITDATA primitive, 802.11 standard section
 * 6.2.1.1.2.

 * The figure in section 7.1.2 suggests a body size of up to 2312
 * bytes is allowed, which is a bit confusing, I suspect this
 * represents the 2304 bytes of real data, plus a possible 8 bytes of
 * WEP IV and ICV. (this interpretation suggested by Ramiro Barreiro)
 */

#define IEEE80211_HLEN			30
#define IEEE80211_FRAME_LEN		(IEEE80211_DATA_LEN + IEEE80211_HLEN)

/* this is stolen from ipw2200 driver */
#define IEEE_IBSS_MAC_HASH_SIZE 31

enum eap_type {
	EAP_PACKET = 0,
	EAPOL_START,
	EAPOL_LOGOFF,
	EAPOL_KEY,
	EAPOL_ENCAP_ASF_ALERT
};

#define IEEE80211_3ADDR_LEN 24
#define IEEE80211_4ADDR_LEN 30
#define IEEE80211_FCS_LEN    4

#define MIN_FRAG_THRESHOLD     256U
#define	MAX_FRAG_THRESHOLD     2346U

/* sequence control field */
#define RTW_IEEE80211_SCTL_FRAG	0x000F
#define RTW_IEEE80211_SCTL_SEQ	0xFFF0

#define RTW_ERP_INFO_NON_ERP_PRESENT BIT(0)
#define RTW_ERP_INFO_USE_PROTECTION BIT(1)
#define RTW_ERP_INFO_BARKER_PREAMBLE_MODE BIT(2)

/* QoS, QOS */
#define NORMAL_ACK			0
#define NO_ACK				1
#define NON_EXPLICIT_ACK		2
#define BLOCK_ACK			3

#ifndef ETH_P_PAE
#define ETH_P_PAE 0x888E /* Port Access Entity (IEEE 802.1X) */
#endif /* ETH_P_PAE */

#define ETH_P_PREAUTH 0x88C7 /* IEEE 802.11i pre-authentication */

#define ETH_P_ECONET	0x0018

#ifndef ETH_P_80211_RAW
#define ETH_P_80211_RAW (ETH_P_ECONET + 1)
#endif

/* IEEE 802.11 defines */

#define P80211_OUI_LEN 3

struct ieee80211_snap_hdr {
	u8    dsap;   /* always 0xAA */
	u8    ssap;   /* always 0xAA */
	u8    ctrl;   /* always 0x03 */
	u8    oui[P80211_OUI_LEN];    /* organizational universal id */
} __packed;

#define SNAP_SIZE sizeof(struct ieee80211_snap_hdr)

#define WLAN_QC_GET_TID(qc) ((qc) & 0x0f)

#define WLAN_GET_SEQ_FRAG(seq) ((seq) & RTW_IEEE80211_SCTL_FRAG)
#define WLAN_GET_SEQ_SEQ(seq)  ((seq) & RTW_IEEE80211_SCTL_SEQ)

/* Non standard?  Not in <linux/ieee80211.h> */
#define WLAN_REASON_EXPIRATION_CHK 65535

#define IEEE80211_MGMT_HDR_LEN 24
#define IEEE80211_DATA_HDR3_LEN 24
#define IEEE80211_DATA_HDR4_LEN 30

#define IEEE80211_CCK_MODULATION	BIT(0)
#define IEEE80211_OFDM_MODULATION	BIT(1)

#define IEEE80211_24GHZ_BAND	BIT(0)
#define IEEE80211_52GHZ_BAND	BIT(1)

#define IEEE80211_CCK_RATE_LEN			4
#define IEEE80211_NUM_OFDM_RATESLEN	8

#define IEEE80211_CCK_RATE_1MB			0x02
#define IEEE80211_CCK_RATE_2MB			0x04
#define IEEE80211_CCK_RATE_5MB			0x0B
#define IEEE80211_CCK_RATE_11MB			0x16
#define IEEE80211_OFDM_RATE_LEN			8
#define IEEE80211_OFDM_RATE_6MB			0x0C
#define IEEE80211_OFDM_RATE_9MB			0x12
#define IEEE80211_OFDM_RATE_12MB		0x18
#define IEEE80211_OFDM_RATE_18MB		0x24
#define IEEE80211_OFDM_RATE_24MB		0x30
#define IEEE80211_OFDM_RATE_36MB		0x48
#define IEEE80211_OFDM_RATE_48MB		0x60
#define IEEE80211_OFDM_RATE_54MB		0x6C
#define IEEE80211_BASIC_RATE_MASK		0x80

#define IEEE80211_CCK_RATE_1MB_MASK		BIT(0)
#define IEEE80211_CCK_RATE_2MB_MASK		BIT(1)
#define IEEE80211_CCK_RATE_5MB_MASK		BIT(2)
#define IEEE80211_CCK_RATE_11MB_MASK		BIT(3)
#define IEEE80211_OFDM_RATE_6MB_MASK		BIT(4)
#define IEEE80211_OFDM_RATE_9MB_MASK		BIT(5)
#define IEEE80211_OFDM_RATE_12MB_MASK		BIT(6)
#define IEEE80211_OFDM_RATE_18MB_MASK		BIT(7)
#define IEEE80211_OFDM_RATE_24MB_MASK		BIT(8)
#define IEEE80211_OFDM_RATE_36MB_MASK		BIT(9)
#define IEEE80211_OFDM_RATE_48MB_MASK		BIT(10)
#define IEEE80211_OFDM_RATE_54MB_MASK		BIT(11)

#define IEEE80211_CCK_RATES_MASK		0x0000000F
#define IEEE80211_CCK_BASIC_RATES_MASK	(IEEE80211_CCK_RATE_1MB_MASK | \
	IEEE80211_CCK_RATE_2MB_MASK)
#define IEEE80211_CCK_DEFAULT_RATES_MASK				\
	(IEEE80211_CCK_BASIC_RATES_MASK |				\
	IEEE80211_CCK_RATE_5MB_MASK |					\
	IEEE80211_CCK_RATE_11MB_MASK)

#define IEEE80211_OFDM_RATES_MASK		0x00000FF0
#define IEEE80211_OFDM_BASIC_RATES_MASK	(IEEE80211_OFDM_RATE_6MB_MASK | \
	IEEE80211_OFDM_RATE_12MB_MASK |					\
	IEEE80211_OFDM_RATE_24MB_MASK)
#define IEEE80211_OFDM_DEFAULT_RATES_MASK				\
	(IEEE80211_OFDM_BASIC_RATES_MASK |				\
	IEEE80211_OFDM_RATE_9MB_MASK  |					\
	IEEE80211_OFDM_RATE_18MB_MASK |					\
	IEEE80211_OFDM_RATE_36MB_MASK |					\
	IEEE80211_OFDM_RATE_48MB_MASK |					\
	IEEE80211_OFDM_RATE_54MB_MASK)

#define IEEE80211_NUM_OFDM_RATES	8
#define IEEE80211_NUM_CCK_RATES		4
#define IEEE80211_OFDM_SHIFT_MASK_A	4

/* IEEE 802.11 requires that STA supports concurrent reception of at least
 * three fragmented frames. This define can be increased to support more
 * concurrent frames, but it should be noted that each entry can consume about
 * 2 kB of RAM and increasing cache size will slow down frame reassembly.
 */
#define IEEE80211_FRAG_CACHE_LEN 4

#define SEC_KEY_1	BIT(0)
#define SEC_KEY_2	BIT(1)
#define SEC_KEY_3	BIT(2)
#define SEC_KEY_4	BIT(3)
#define SEC_ACTIVE_KEY  BIT(4)
#define SEC_AUTH_MODE   BIT(5)
#define SEC_UNICAST_GROUP BIT(6)
#define SEC_LEVEL	BIT(7)
#define SEC_ENABLED     BIT(8)

#define SEC_LEVEL_0      0 /* None */
#define SEC_LEVEL_1      1 /* WEP 40 and 104 bit */
#define SEC_LEVEL_2      2 /* Level 1 + TKIP */
#define SEC_LEVEL_2_CKIP 3 /* Level 1 + CKIP */
#define SEC_LEVEL_3      4 /* Level 2 + CCMP */

#define WEP_KEYS 4
#define WEP_KEY_LEN 13

/* SWEEP TABLE ENTRIES NUMBER*/
#define MAX_SWEEP_TAB_ENTRIES		  42
#define MAX_SWEEP_TAB_ENTRIES_PER_PACKET  7
/* MAX_RATES_LENGTH needs to be 12.  The spec says 8, and many APs
 * only use 8, and then use extended rates for the remaining supported
 * rates.  Other APs, however, stick all of their supported rates on the
 * main rates information element...
 */
#define MAX_RATES_LENGTH		((u8)12)
#define MAX_RATES_EX_LENGTH		((u8)16)
#define MAX_NETWORK_COUNT		128
#define MAX_CHANNEL_NUMBER		161
#define IEEE80211_SOFTMAC_SCAN_TIME	400
/* HZ / 2) */
#define IEEE80211_SOFTMAC_ASSOC_RETRY_TIME (HZ * 2)

#define CRC_LENGTH		 4U

#define MAX_WPA_IE_LEN (256)
#define MAX_WPS_IE_LEN (512)
#define MAX_P2P_IE_LEN (256)
#define MAX_WFD_IE_LEN (128)

#define NETWORK_EMPTY_ESSID	BIT(0)
#define NETWORK_HAS_OFDM	BIT(1)
#define NETWORK_HAS_CCK		BIT(2)

#define IW_ESSID_MAX_SIZE 32
/*
 * join_res:
 * -1: authentication fail
 * -2: association fail
 * > 0: TID
 */

enum ieee80211_state {
	/* the card is not linked at all */
	IEEE80211_NOLINK = 0,

	/* IEEE80211_ASSOCIATING* are for BSS client mode
	 * the driver shall not perform RX filtering unless
	 * the state is LINKED.
	 * The driver shall just check for the state LINKED and
	 * defaults to NOLINK for ALL the other states (including
	 * LINKED_SCANNING)
	 */

	/* the association procedure will start (wq scheduling)*/
	IEEE80211_ASSOCIATING,
	IEEE80211_ASSOCIATING_RETRY,

	/* the association procedure is sending AUTH request*/
	IEEE80211_ASSOCIATING_AUTHENTICATING,

	/* the association procedure has successfully authentcated
	 * and is sending association request
	 */
	IEEE80211_ASSOCIATING_AUTHENTICATED,

	/* the link is ok. the card associated to a BSS or linked
	 * to a ibss cell or acting as an AP and creating the bss
	 */
	IEEE80211_LINKED,

	/* same as LINKED, but the driver shall apply RX filter
	 * rules as we are in NO_LINK mode. As the card is still
	 * logically linked, but it is doing a syncro site survey
	 * then it will be back to LINKED state.
	 */
	IEEE80211_LINKED_SCANNING,

};

#define DEFAULT_MAX_SCAN_AGE (15 * HZ)
#define DEFAULT_FTS 2346

#define CFG_IEEE80211_RESERVE_FCS	BIT(0)
#define CFG_IEEE80211_COMPUTE_FCS	BIT(1)

#define MAXTID	16

#define IEEE_A	    BIT(0)
#define IEEE_B	    BIT(1)
#define IEEE_G	    BIT(2)
#define IEEE_MODE_MASK    (IEEE_A | IEEE_B | IEEE_G)

/* Action category code */
enum rtw_ieee80211_category {
	RTW_WLAN_CATEGORY_SPECTRUM_MGMT = 0,
	RTW_WLAN_CATEGORY_QOS = 1,
	RTW_WLAN_CATEGORY_DLS = 2,
	RTW_WLAN_CATEGORY_BACK = 3,
	RTW_WLAN_CATEGORY_PUBLIC = 4, /* IEEE 802.11 public action frames */
	RTW_WLAN_CATEGORY_RADIO_MEASUREMENT  = 5,
	RTW_WLAN_CATEGORY_FT = 6,
	RTW_WLAN_CATEGORY_HT = 7,
	RTW_WLAN_CATEGORY_SA_QUERY = 8,
	RTW_WLAN_CATEGORY_TDLS = 12,
	RTW_WLAN_CATEGORY_WMM = 17,
	RTW_WLAN_CATEGORY_P2P = 0x7f,/* P2P action frames */
};

enum _PUBLIC_ACTION {
	ACT_PUBLIC_BSSCOEXIST = 0, /*  20/40 BSS Coexistence */
	ACT_PUBLIC_DSE_ENABLE = 1,
	ACT_PUBLIC_DSE_DEENABLE = 2,
	ACT_PUBLIC_DSE_REG_LOCATION = 3,
	ACT_PUBLIC_EXT_CHL_SWITCH = 4,
	ACT_PUBLIC_DSE_MSR_REQ = 5,
	ACT_PUBLIC_DSE_MSR_RPRT = 6,
	ACT_PUBLIC_MP = 7, /*  Measurement Pilot */
	ACT_PUBLIC_DSE_PWR_CONSTRAINT = 8,
	ACT_PUBLIC_VENDOR = 9, /*  for WIFI_DIRECT */
	ACT_PUBLIC_GAS_INITIAL_REQ = 10,
	ACT_PUBLIC_GAS_INITIAL_RSP = 11,
	ACT_PUBLIC_GAS_COMEBACK_REQ = 12,
	ACT_PUBLIC_GAS_COMEBACK_RSP = 13,
	ACT_PUBLIC_TDLS_DISCOVERY_RSP = 14,
	ACT_PUBLIC_LOCATION_TRACK = 15,
	ACT_PUBLIC_MAX
};

/* BACK action code */
enum rtw_ieee80211_back_actioncode {
	RTW_WLAN_ACTION_ADDBA_REQ = 0,
	RTW_WLAN_ACTION_ADDBA_RESP = 1,
	RTW_WLAN_ACTION_DELBA = 2,
};

/* HT features action code */
enum rtw_ieee80211_ht_actioncode {
	RTW_WLAN_ACTION_NOTIFY_CH_WIDTH = 0,
	RTW_WLAN_ACTION_SM_PS = 1,
	RTW_WLAN_ACTION_PSPM = 2,
	RTW_WLAN_ACTION_PCO_PHASE = 3,
	RTW_WLAN_ACTION_MIMO_CSI_MX = 4,
	RTW_WLAN_ACTION_MIMO_NONCP_BF = 5,
	RTW_WLAN_ACTION_MIMP_CP_BF = 6,
	RTW_WLAN_ACTION_ASEL_INDICATES_FB = 7,
	RTW_WLAN_ACTION_HI_INFO_EXCHG = 8,
};

/* BACK (block-ack) parties */
enum rtw_ieee80211_back_parties {
	RTW_WLAN_BACK_RECIPIENT = 0,
	RTW_WLAN_BACK_INITIATOR = 1,
	RTW_WLAN_BACK_TIMER = 2,
};

#define OUI_MICROSOFT 0x0050f2 /* Microsoft (also used in Wi-Fi specs)
				* 00:50:F2
				*/
#define WME_OUI_TYPE 2
#define WME_OUI_SUBTYPE_INFORMATION_ELEMENT 0
#define WME_OUI_SUBTYPE_PARAMETER_ELEMENT 1
#define WME_OUI_SUBTYPE_TSPEC_ELEMENT 2
#define WME_VERSION 1

#define WME_ACTION_CODE_SETUP_REQUEST 0
#define WME_ACTION_CODE_SETUP_RESPONSE 1
#define WME_ACTION_CODE_TEARDOWN 2

#define WME_SETUP_RESPONSE_STATUS_ADMISSION_ACCEPTED 0
#define WME_SETUP_RESPONSE_STATUS_INVALID_PARAMETERS 1
#define WME_SETUP_RESPONSE_STATUS_REFUSED 3

#define WME_TSPEC_DIRECTION_UPLINK 0
#define WME_TSPEC_DIRECTION_DOWNLINK 1
#define WME_TSPEC_DIRECTION_BI_DIRECTIONAL 3

#define OUI_BROADCOM 0x00904c /* Broadcom (Epigram) */

#define VENDOR_HT_CAPAB_OUI_TYPE 0x33 /* 00-90-4c:0x33 */

/**
 * enum rtw_ieee80211_channel_flags - channel flags
 *
 * Channel flags set by the regulatory control code.
 *
 * @RTW_IEEE80211_CHAN_DISABLED: This channel is disabled.
 * @RTW_IEEE80211_CHAN_PASSIVE_SCAN: Only passive scanning is permitted
 *      on this channel.
 * @RTW_IEEE80211_CHAN_NO_IBSS: IBSS is not allowed on this channel.
 * @RTW_IEEE80211_CHAN_RADAR: Radar detection is required on this channel.
 * @RTW_IEEE80211_CHAN_NO_HT40PLUS: extension channel above this channel
 *      is not permitted.
 * @RTW_IEEE80211_CHAN_NO_HT40MINUS: extension channel below this channel
 *      is not permitted.
 */
enum rtw_ieee80211_channel_flags {
	RTW_IEEE80211_CHAN_DISABLED	 = BIT(0),
	RTW_IEEE80211_CHAN_PASSIVE_SCAN     = BIT(1),
	RTW_IEEE80211_CHAN_NO_IBSS	  = BIT(2),
	RTW_IEEE80211_CHAN_RADAR	    = BIT(3),
	RTW_IEEE80211_CHAN_NO_HT40PLUS      = BIT(4),
	RTW_IEEE80211_CHAN_NO_HT40MINUS     = BIT(5),
};

#define RTW_IEEE80211_CHAN_NO_HT40 \
	  (RTW_IEEE80211_CHAN_NO_HT40PLUS | RTW_IEEE80211_CHAN_NO_HT40MINUS)

/* Represent channel details, subset of ieee80211_channel */
struct rtw_ieee80211_channel {
	u16 hw_value;
	u32 flags;
};

#define CHAN_FMT \
	"hw_value:%u, " \
	"flags:0x%08x" \

#define CHAN_ARG(channel) \
	(channel)->hw_value \
	, (channel)->flags \

/* Parsed Information Elements */
struct rtw_ieee802_11_elems {
	u8 *ssid;
	u8 ssid_len;
	u8 *supp_rates;
	u8 supp_rates_len;
	u8 *fh_params;
	u8 fh_params_len;
	u8 *ds_params;
	u8 ds_params_len;
	u8 *cf_params;
	u8 cf_params_len;
	u8 *tim;
	u8 tim_len;
	u8 *ibss_params;
	u8 ibss_params_len;
	u8 *challenge;
	u8 challenge_len;
	u8 *erp_info;
	u8 erp_info_len;
	u8 *ext_supp_rates;
	u8 ext_supp_rates_len;
	u8 *wpa_ie;
	u8 wpa_ie_len;
	u8 *rsn_ie;
	u8 rsn_ie_len;
	u8 *wme;
	u8 wme_len;
	u8 *wme_tspec;
	u8 wme_tspec_len;
	u8 *wps_ie;
	u8 wps_ie_len;
	u8 *power_cap;
	u8 power_cap_len;
	u8 *supp_channels;
	u8 supp_channels_len;
	u8 *mdie;
	u8 mdie_len;
	u8 *ftie;
	u8 ftie_len;
	u8 *timeout_int;
	u8 timeout_int_len;
	u8 *ht_capabilities;
	u8 ht_capabilities_len;
	u8 *ht_operation;
	u8 ht_operation_len;
	u8 *vendor_ht_cap;
	u8 vendor_ht_cap_len;
};

enum parse_res {
	ParseOK = 0,
	ParseUnknown = 1,
	ParseFailed = -1
};

enum parse_res rtw_ieee802_11_parse_elems(u8 *start, uint len,
					  struct rtw_ieee802_11_elems *elems,
					  int show_errors);

u8 *rtw_set_fixed_ie(void *pbuf, unsigned int len,
		     void *source, unsigned int *frlen);
u8 *rtw_set_ie(u8 *pbuf, int index, uint len, u8 *source, uint *frlen);

enum secondary_ch_offset {
	SCN = 0, /* no secondary channel */
	SCA = 1, /* secondary channel above */
	SCB = 3,  /* secondary channel below */
};

u8 *rtw_get_ie(u8 *pbuf, int index, uint *len, int limit);

void rtw_set_supported_rate(u8 *SupportedRates, uint mode);

unsigned char *rtw_get_wpa_ie(unsigned char *pie, uint *wpa_ie_len, int limit);
unsigned char *rtw_get_wpa2_ie(unsigned char *pie, uint *rsn_ie_len, int limit);
int rtw_get_wpa_cipher_suite(u8 *s);
int rtw_get_wpa2_cipher_suite(u8 *s);
int rtw_get_wapi_ie(u8 *in_ie, uint in_len, u8 *wapi_ie, u16 *wapi_len);
int rtw_parse_wpa_ie(u8 *wpa_ie, int wpa_ie_len, int *group_cipher,
		     int *pairwise_cipher, int *is_8021x);
int rtw_parse_wpa2_ie(u8 *wpa_ie, int wpa_ie_len, int *group_cipher,
		      int *pairwise_cipher, int *is_8021x);

void rtw_get_sec_ie(u8 *in_ie, uint in_len, u8 *rsn_ie, u16 *rsn_len,
		    u8 *wpa_ie, u16 *wpa_len);

u8 rtw_is_wps_ie(u8 *ie_ptr, uint *wps_ielen);
u8 *rtw_get_wps_ie(u8 *in_ie, uint in_len, u8 *wps_ie, uint *wps_ielen);
u8 *rtw_get_wps_attr(u8 *wps_ie, uint wps_ielen, u16 target_attr_id,
		     u8 *buf_attr, u32 *len_attr);
u8 *rtw_get_wps_attr_content(u8 *wps_ie, uint wps_ielen, u16 target_attr_id,
			     u8 *buf_content, uint *len_content);

uint	rtw_get_rateset_len(u8	*rateset);

struct registry_priv;
int rtw_generate_ie(struct registry_priv *pregistrypriv);

int rtw_get_bit_value_from_ieee_value(u8 val);

bool rtw_is_cckrates_included(u8 *rate);

bool rtw_is_cckratesonly_included(u8 *rate);

int rtw_check_network_type(unsigned char *rate);

void rtw_get_bcn_info(struct wlan_network *pnetwork);

void rtw_macaddr_cfg(u8 *mac_addr);

u16 rtw_mcs_rate(u8 rf_type, u8 bw_40MHz, u8 short_GI_20, u8 short_GI_40,
		 unsigned char *MCS_rate);

#endif /* IEEE80211_H */