blob: 23151abe53c67b690033b782336a8193e9b7ebfe [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0-only */
/*
* linux/arch/unicore32/kernel/sleep.S
*
* Code specific to PKUnity SoC and UniCore ISA
*
* Maintained by GUAN Xue-tao <gxt@mprc.pku.edu.cn>
* Copyright (C) 2001-2010 Guan Xuetao
*/
#include <linux/linkage.h>
#include <asm/assembler.h>
#include <mach/hardware.h>
.text
pkunity_cpu_save_cp:
@ get coprocessor registers
movc r3, p0.c7, #0 @ PID
movc r4, p0.c2, #0 @ translation table base addr
movc r5, p0.c1, #0 @ control reg
@ store them plus current virtual stack ptr on stack
mov r6, sp
stm.w (r3 - r6), [sp-]
mov pc, lr
pkunity_cpu_save_sp:
@ preserve phys address of stack
mov r0, sp
stw.w lr, [sp+], #-4
b.l sleep_phys_sp
ldw r1, =sleep_save_sp
stw r0, [r1]
ldw.w pc, [sp]+, #4
/*
* puv3_cpu_suspend()
*
* Forces CPU into sleep state.
*
* r0 = value for PWRMODE M field for desired sleep state
*/
ENTRY(puv3_cpu_suspend)
stm.w (r16 - r27, lr), [sp-] @ save registers on stack
stm.w (r4 - r15), [sp-] @ save registers on stack
#ifdef CONFIG_UNICORE_FPU_F64
sfm.w (f0 - f7 ), [sp-]
sfm.w (f8 - f15), [sp-]
sfm.w (f16 - f23), [sp-]
sfm.w (f24 - f31), [sp-]
cff r4, s31
stm.w (r4), [sp-]
#endif
b.l pkunity_cpu_save_cp
b.l pkunity_cpu_save_sp
@ clean data cache
mov r1, #0
movc p0.c5, r1, #14
nop
nop
nop
nop
@ DDR2 BaseAddr
ldw r0, =(PKUNITY_DDR2CTRL_BASE)
@ PM BaseAddr
ldw r1, =(PKUNITY_PM_BASE)
@ set PLL_SYS_CFG reg, 275
movl r6, #0x00002401
stw r6, [r1+], #0x18
@ set PLL_DDR_CFG reg, 66MHz
movl r6, #0x00100c00
stw r6, [r1+], #0x1c
@ set wake up source
movl r8, #0x800001ff @ epip4d
stw r8, [r1+], #0xc
@ set PGSR
movl r5, #0x40000
stw r5, [r1+], #0x10
@ prepare DDR2 refresh settings
ldw r5, [r0+], #0x24
or r5, r5, #0x00000001
@ prepare PMCR for PLL changing
movl r6, #0xc
@ prepare for closing PLL
movl r7, #0x1
@ prepare sleep mode
mov r8, #0x1
@ movl r0, 0x11111111
@ put_word_ocd r0
b pkunity_cpu_do_suspend
.ltorg
.align 5
pkunity_cpu_do_suspend:
b 101f
@ put DDR2 into self-refresh
100: stw r5, [r0+], #0x24
@ change PLL
stw r6, [r1]
b 1f
.ltorg
.align 5
101: b 102f
@ wait for PLL changing complete
1: ldw r6, [r1+], #0x44
csub.a r6, #0x1
bne 1b
b 2f
.ltorg
.align 5
102: b 100b
@ close PLL
2: stw r7, [r1+], #0x4
@ enter sleep mode
stw r8, [r1]
3: b 3b
/*
* puv3_cpu_resume()
*
* entry point from bootloader into kernel during resume
*
* Note: Yes, part of the following code is located into the .data section.
* This is to allow sleep_save_sp to be accessed with a relative load
* while we can't rely on any MMU translation. We could have put
* sleep_save_sp in the .text section as well, but some setups might
* insist on it to be truly read-only.
*/
.data
.align 5
ENTRY(puv3_cpu_resume)
@ movl r0, 0x20202020
@ put_word_ocd r0
ldw r0, sleep_save_sp @ stack phys addr
ldw r2, =resume_after_mmu @ its absolute virtual address
ldm (r3 - r6), [r0]+ @ CP regs + virt stack ptr
mov sp, r6 @ CP regs + virt stack ptr
mov r1, #0
movc p0.c6, r1, #6 @ invalidate I & D TLBs
movc p0.c5, r1, #28 @ invalidate I & D caches, BTB
movc p0.c7, r3, #0 @ PID
movc p0.c2, r4, #0 @ translation table base addr
movc p0.c1, r5, #0 @ control reg, turn on mmu
nop
jump r2
nop
nop
nop
nop
nop
sleep_save_sp:
.word 0 @ preserve stack phys ptr here
.text
resume_after_mmu:
@ movl r0, 0x30303030
@ put_word_ocd r0
#ifdef CONFIG_UNICORE_FPU_F64
lfm.w (f0 - f7 ), [sp]+
lfm.w (f8 - f15), [sp]+
lfm.w (f16 - f23), [sp]+
lfm.w (f24 - f31), [sp]+
ldm.w (r4), [sp]+
ctf r4, s31
#endif
ldm.w (r4 - r15), [sp]+ @ restore registers from stack
ldm.w (r16 - r27, pc), [sp]+ @ return to caller