| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Application UART driver for: |
| * Freescale STMP37XX/STMP378X |
| * Alphascale ASM9260 |
| * |
| * Author: dmitry pervushin <dimka@embeddedalley.com> |
| * |
| * Copyright 2014 Oleksij Rempel <linux@rempel-privat.de> |
| * Provide Alphascale ASM9260 support. |
| * Copyright 2008-2010 Freescale Semiconductor, Inc. |
| * Copyright 2008 Embedded Alley Solutions, Inc All Rights Reserved. |
| */ |
| |
| #if defined(CONFIG_SERIAL_MXS_AUART_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) |
| #define SUPPORT_SYSRQ |
| #endif |
| |
| #include <linux/kernel.h> |
| #include <linux/errno.h> |
| #include <linux/init.h> |
| #include <linux/console.h> |
| #include <linux/interrupt.h> |
| #include <linux/module.h> |
| #include <linux/slab.h> |
| #include <linux/wait.h> |
| #include <linux/tty.h> |
| #include <linux/tty_driver.h> |
| #include <linux/tty_flip.h> |
| #include <linux/serial.h> |
| #include <linux/serial_core.h> |
| #include <linux/platform_device.h> |
| #include <linux/device.h> |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/io.h> |
| #include <linux/of_device.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/dmaengine.h> |
| |
| #include <asm/cacheflush.h> |
| |
| #include <linux/gpio/consumer.h> |
| #include <linux/err.h> |
| #include <linux/irq.h> |
| #include "serial_mctrl_gpio.h" |
| |
| #define MXS_AUART_PORTS 5 |
| #define MXS_AUART_FIFO_SIZE 16 |
| |
| #define SET_REG 0x4 |
| #define CLR_REG 0x8 |
| #define TOG_REG 0xc |
| |
| #define AUART_CTRL0 0x00000000 |
| #define AUART_CTRL1 0x00000010 |
| #define AUART_CTRL2 0x00000020 |
| #define AUART_LINECTRL 0x00000030 |
| #define AUART_LINECTRL2 0x00000040 |
| #define AUART_INTR 0x00000050 |
| #define AUART_DATA 0x00000060 |
| #define AUART_STAT 0x00000070 |
| #define AUART_DEBUG 0x00000080 |
| #define AUART_VERSION 0x00000090 |
| #define AUART_AUTOBAUD 0x000000a0 |
| |
| #define AUART_CTRL0_SFTRST (1 << 31) |
| #define AUART_CTRL0_CLKGATE (1 << 30) |
| #define AUART_CTRL0_RXTO_ENABLE (1 << 27) |
| #define AUART_CTRL0_RXTIMEOUT(v) (((v) & 0x7ff) << 16) |
| #define AUART_CTRL0_XFER_COUNT(v) ((v) & 0xffff) |
| |
| #define AUART_CTRL1_XFER_COUNT(v) ((v) & 0xffff) |
| |
| #define AUART_CTRL2_DMAONERR (1 << 26) |
| #define AUART_CTRL2_TXDMAE (1 << 25) |
| #define AUART_CTRL2_RXDMAE (1 << 24) |
| |
| #define AUART_CTRL2_CTSEN (1 << 15) |
| #define AUART_CTRL2_RTSEN (1 << 14) |
| #define AUART_CTRL2_RTS (1 << 11) |
| #define AUART_CTRL2_RXE (1 << 9) |
| #define AUART_CTRL2_TXE (1 << 8) |
| #define AUART_CTRL2_UARTEN (1 << 0) |
| |
| #define AUART_LINECTRL_BAUD_DIV_MAX 0x003fffc0 |
| #define AUART_LINECTRL_BAUD_DIV_MIN 0x000000ec |
| #define AUART_LINECTRL_BAUD_DIVINT_SHIFT 16 |
| #define AUART_LINECTRL_BAUD_DIVINT_MASK 0xffff0000 |
| #define AUART_LINECTRL_BAUD_DIVINT(v) (((v) & 0xffff) << 16) |
| #define AUART_LINECTRL_BAUD_DIVFRAC_SHIFT 8 |
| #define AUART_LINECTRL_BAUD_DIVFRAC_MASK 0x00003f00 |
| #define AUART_LINECTRL_BAUD_DIVFRAC(v) (((v) & 0x3f) << 8) |
| #define AUART_LINECTRL_SPS (1 << 7) |
| #define AUART_LINECTRL_WLEN_MASK 0x00000060 |
| #define AUART_LINECTRL_WLEN(v) (((v) & 0x3) << 5) |
| #define AUART_LINECTRL_FEN (1 << 4) |
| #define AUART_LINECTRL_STP2 (1 << 3) |
| #define AUART_LINECTRL_EPS (1 << 2) |
| #define AUART_LINECTRL_PEN (1 << 1) |
| #define AUART_LINECTRL_BRK (1 << 0) |
| |
| #define AUART_INTR_RTIEN (1 << 22) |
| #define AUART_INTR_TXIEN (1 << 21) |
| #define AUART_INTR_RXIEN (1 << 20) |
| #define AUART_INTR_CTSMIEN (1 << 17) |
| #define AUART_INTR_RTIS (1 << 6) |
| #define AUART_INTR_TXIS (1 << 5) |
| #define AUART_INTR_RXIS (1 << 4) |
| #define AUART_INTR_CTSMIS (1 << 1) |
| |
| #define AUART_STAT_BUSY (1 << 29) |
| #define AUART_STAT_CTS (1 << 28) |
| #define AUART_STAT_TXFE (1 << 27) |
| #define AUART_STAT_TXFF (1 << 25) |
| #define AUART_STAT_RXFE (1 << 24) |
| #define AUART_STAT_OERR (1 << 19) |
| #define AUART_STAT_BERR (1 << 18) |
| #define AUART_STAT_PERR (1 << 17) |
| #define AUART_STAT_FERR (1 << 16) |
| #define AUART_STAT_RXCOUNT_MASK 0xffff |
| |
| /* |
| * Start of Alphascale asm9260 defines |
| * This list contains only differences of existing bits |
| * between imx2x and asm9260 |
| */ |
| #define ASM9260_HW_CTRL0 0x0000 |
| /* |
| * RW. Tell the UART to execute the RX DMA Command. The |
| * UART will clear this bit at the end of receive execution. |
| */ |
| #define ASM9260_BM_CTRL0_RXDMA_RUN BIT(28) |
| /* RW. 0 use FIFO for status register; 1 use DMA */ |
| #define ASM9260_BM_CTRL0_RXTO_SOURCE_STATUS BIT(25) |
| /* |
| * RW. RX TIMEOUT Enable. Valid for FIFO and DMA. |
| * Warning: If this bit is set to 0, the RX timeout will not affect receive DMA |
| * operation. If this bit is set to 1, a receive timeout will cause the receive |
| * DMA logic to terminate by filling the remaining DMA bytes with garbage data. |
| */ |
| #define ASM9260_BM_CTRL0_RXTO_ENABLE BIT(24) |
| /* |
| * RW. Receive Timeout Counter Value: number of 8-bit-time to wait before |
| * asserting timeout on the RX input. If the RXFIFO is not empty and the RX |
| * input is idle, then the watchdog counter will decrement each bit-time. Note |
| * 7-bit-time is added to the programmed value, so a value of zero will set |
| * the counter to 7-bit-time, a value of 0x1 gives 15-bit-time and so on. Also |
| * note that the counter is reloaded at the end of each frame, so if the frame |
| * is 10 bits long and the timeout counter value is zero, then timeout will |
| * occur (when FIFO is not empty) even if the RX input is not idle. The default |
| * value is 0x3 (31 bit-time). |
| */ |
| #define ASM9260_BM_CTRL0_RXTO_MASK (0xff << 16) |
| /* TIMEOUT = (100*7+1)*(1/BAUD) */ |
| #define ASM9260_BM_CTRL0_DEFAULT_RXTIMEOUT (20 << 16) |
| |
| /* TX ctrl register */ |
| #define ASM9260_HW_CTRL1 0x0010 |
| /* |
| * RW. Tell the UART to execute the TX DMA Command. The |
| * UART will clear this bit at the end of transmit execution. |
| */ |
| #define ASM9260_BM_CTRL1_TXDMA_RUN BIT(28) |
| |
| #define ASM9260_HW_CTRL2 0x0020 |
| /* |
| * RW. Receive Interrupt FIFO Level Select. |
| * The trigger points for the receive interrupt are as follows: |
| * ONE_EIGHTHS = 0x0 Trigger on FIFO full to at least 2 of 16 entries. |
| * ONE_QUARTER = 0x1 Trigger on FIFO full to at least 4 of 16 entries. |
| * ONE_HALF = 0x2 Trigger on FIFO full to at least 8 of 16 entries. |
| * THREE_QUARTERS = 0x3 Trigger on FIFO full to at least 12 of 16 entries. |
| * SEVEN_EIGHTHS = 0x4 Trigger on FIFO full to at least 14 of 16 entries. |
| */ |
| #define ASM9260_BM_CTRL2_RXIFLSEL (7 << 20) |
| #define ASM9260_BM_CTRL2_DEFAULT_RXIFLSEL (3 << 20) |
| /* RW. Same as RXIFLSEL */ |
| #define ASM9260_BM_CTRL2_TXIFLSEL (7 << 16) |
| #define ASM9260_BM_CTRL2_DEFAULT_TXIFLSEL (2 << 16) |
| /* RW. Set DTR. When this bit is 1, the output is 0. */ |
| #define ASM9260_BM_CTRL2_DTR BIT(10) |
| /* RW. Loop Back Enable */ |
| #define ASM9260_BM_CTRL2_LBE BIT(7) |
| #define ASM9260_BM_CTRL2_PORT_ENABLE BIT(0) |
| |
| #define ASM9260_HW_LINECTRL 0x0030 |
| /* |
| * RW. Stick Parity Select. When bits 1, 2, and 7 of this register are set, the |
| * parity bit is transmitted and checked as a 0. When bits 1 and 7 are set, |
| * and bit 2 is 0, the parity bit is transmitted and checked as a 1. When this |
| * bit is cleared stick parity is disabled. |
| */ |
| #define ASM9260_BM_LCTRL_SPS BIT(7) |
| /* RW. Word length */ |
| #define ASM9260_BM_LCTRL_WLEN (3 << 5) |
| #define ASM9260_BM_LCTRL_CHRL_5 (0 << 5) |
| #define ASM9260_BM_LCTRL_CHRL_6 (1 << 5) |
| #define ASM9260_BM_LCTRL_CHRL_7 (2 << 5) |
| #define ASM9260_BM_LCTRL_CHRL_8 (3 << 5) |
| |
| /* |
| * Interrupt register. |
| * contains the interrupt enables and the interrupt status bits |
| */ |
| #define ASM9260_HW_INTR 0x0040 |
| /* Tx FIFO EMPTY Raw Interrupt enable */ |
| #define ASM9260_BM_INTR_TFEIEN BIT(27) |
| /* Overrun Error Interrupt Enable. */ |
| #define ASM9260_BM_INTR_OEIEN BIT(26) |
| /* Break Error Interrupt Enable. */ |
| #define ASM9260_BM_INTR_BEIEN BIT(25) |
| /* Parity Error Interrupt Enable. */ |
| #define ASM9260_BM_INTR_PEIEN BIT(24) |
| /* Framing Error Interrupt Enable. */ |
| #define ASM9260_BM_INTR_FEIEN BIT(23) |
| |
| /* nUARTDSR Modem Interrupt Enable. */ |
| #define ASM9260_BM_INTR_DSRMIEN BIT(19) |
| /* nUARTDCD Modem Interrupt Enable. */ |
| #define ASM9260_BM_INTR_DCDMIEN BIT(18) |
| /* nUARTRI Modem Interrupt Enable. */ |
| #define ASM9260_BM_INTR_RIMIEN BIT(16) |
| /* Auto-Boud Timeout */ |
| #define ASM9260_BM_INTR_ABTO BIT(13) |
| #define ASM9260_BM_INTR_ABEO BIT(12) |
| /* Tx FIFO EMPTY Raw Interrupt state */ |
| #define ASM9260_BM_INTR_TFEIS BIT(11) |
| /* Overrun Error */ |
| #define ASM9260_BM_INTR_OEIS BIT(10) |
| /* Break Error */ |
| #define ASM9260_BM_INTR_BEIS BIT(9) |
| /* Parity Error */ |
| #define ASM9260_BM_INTR_PEIS BIT(8) |
| /* Framing Error */ |
| #define ASM9260_BM_INTR_FEIS BIT(7) |
| #define ASM9260_BM_INTR_DSRMIS BIT(3) |
| #define ASM9260_BM_INTR_DCDMIS BIT(2) |
| #define ASM9260_BM_INTR_RIMIS BIT(0) |
| |
| /* |
| * RW. In DMA mode, up to 4 Received/Transmit characters can be accessed at a |
| * time. In PIO mode, only one character can be accessed at a time. The status |
| * register contains the receive data flags and valid bits. |
| */ |
| #define ASM9260_HW_DATA 0x0050 |
| |
| #define ASM9260_HW_STAT 0x0060 |
| /* RO. If 1, UARTAPP is present in this product. */ |
| #define ASM9260_BM_STAT_PRESENT BIT(31) |
| /* RO. If 1, HISPEED is present in this product. */ |
| #define ASM9260_BM_STAT_HISPEED BIT(30) |
| /* RO. Receive FIFO Full. */ |
| #define ASM9260_BM_STAT_RXFULL BIT(26) |
| |
| /* RO. The UART Debug Register contains the state of the DMA signals. */ |
| #define ASM9260_HW_DEBUG 0x0070 |
| /* DMA Command Run Status */ |
| #define ASM9260_BM_DEBUG_TXDMARUN BIT(5) |
| #define ASM9260_BM_DEBUG_RXDMARUN BIT(4) |
| /* DMA Command End Status */ |
| #define ASM9260_BM_DEBUG_TXCMDEND BIT(3) |
| #define ASM9260_BM_DEBUG_RXCMDEND BIT(2) |
| /* DMA Request Status */ |
| #define ASM9260_BM_DEBUG_TXDMARQ BIT(1) |
| #define ASM9260_BM_DEBUG_RXDMARQ BIT(0) |
| |
| #define ASM9260_HW_ILPR 0x0080 |
| |
| #define ASM9260_HW_RS485CTRL 0x0090 |
| /* |
| * RW. This bit reverses the polarity of the direction control signal on the RTS |
| * (or DTR) pin. |
| * If 0, The direction control pin will be driven to logic ‘0’ when the |
| * transmitter has data to be sent. It will be driven to logic ‘1’ after the |
| * last bit of data has been transmitted. |
| */ |
| #define ASM9260_BM_RS485CTRL_ONIV BIT(5) |
| /* RW. Enable Auto Direction Control. */ |
| #define ASM9260_BM_RS485CTRL_DIR_CTRL BIT(4) |
| /* |
| * RW. If 0 and DIR_CTRL = 1, pin RTS is used for direction control. |
| * If 1 and DIR_CTRL = 1, pin DTR is used for direction control. |
| */ |
| #define ASM9260_BM_RS485CTRL_PINSEL BIT(3) |
| /* RW. Enable Auto Address Detect (AAD). */ |
| #define ASM9260_BM_RS485CTRL_AADEN BIT(2) |
| /* RW. Disable receiver. */ |
| #define ASM9260_BM_RS485CTRL_RXDIS BIT(1) |
| /* RW. Enable RS-485/EIA-485 Normal Multidrop Mode (NMM) */ |
| #define ASM9260_BM_RS485CTRL_RS485EN BIT(0) |
| |
| #define ASM9260_HW_RS485ADRMATCH 0x00a0 |
| /* Contains the address match value. */ |
| #define ASM9260_BM_RS485ADRMATCH_MASK (0xff << 0) |
| |
| #define ASM9260_HW_RS485DLY 0x00b0 |
| /* |
| * RW. Contains the direction control (RTS or DTR) delay value. This delay time |
| * is in periods of the baud clock. |
| */ |
| #define ASM9260_BM_RS485DLY_MASK (0xff << 0) |
| |
| #define ASM9260_HW_AUTOBAUD 0x00c0 |
| /* WO. Auto-baud time-out interrupt clear bit. */ |
| #define ASM9260_BM_AUTOBAUD_TO_INT_CLR BIT(9) |
| /* WO. End of auto-baud interrupt clear bit. */ |
| #define ASM9260_BM_AUTOBAUD_EO_INT_CLR BIT(8) |
| /* Restart in case of timeout (counter restarts at next UART Rx falling edge) */ |
| #define ASM9260_BM_AUTOBAUD_AUTORESTART BIT(2) |
| /* Auto-baud mode select bit. 0 - Mode 0, 1 - Mode 1. */ |
| #define ASM9260_BM_AUTOBAUD_MODE BIT(1) |
| /* |
| * Auto-baud start (auto-baud is running). Auto-baud run bit. This bit is |
| * automatically cleared after auto-baud completion. |
| */ |
| #define ASM9260_BM_AUTOBAUD_START BIT(0) |
| |
| #define ASM9260_HW_CTRL3 0x00d0 |
| #define ASM9260_BM_CTRL3_OUTCLK_DIV_MASK (0xffff << 16) |
| /* |
| * RW. Provide clk over OUTCLK pin. In case of asm9260 it can be configured on |
| * pins 137 and 144. |
| */ |
| #define ASM9260_BM_CTRL3_MASTERMODE BIT(6) |
| /* RW. Baud Rate Mode: 1 - Enable sync mode. 0 - async mode. */ |
| #define ASM9260_BM_CTRL3_SYNCMODE BIT(4) |
| /* RW. 1 - MSB bit send frist; 0 - LSB bit frist. */ |
| #define ASM9260_BM_CTRL3_MSBF BIT(2) |
| /* RW. 1 - sample rate = 8 x Baudrate; 0 - sample rate = 16 x Baudrate. */ |
| #define ASM9260_BM_CTRL3_BAUD8 BIT(1) |
| /* RW. 1 - Set word length to 9bit. 0 - use ASM9260_BM_LCTRL_WLEN */ |
| #define ASM9260_BM_CTRL3_9BIT BIT(0) |
| |
| #define ASM9260_HW_ISO7816_CTRL 0x00e0 |
| /* RW. Enable High Speed mode. */ |
| #define ASM9260_BM_ISO7816CTRL_HS BIT(12) |
| /* Disable Successive Receive NACK */ |
| #define ASM9260_BM_ISO7816CTRL_DS_NACK BIT(8) |
| #define ASM9260_BM_ISO7816CTRL_MAX_ITER_MASK (0xff << 4) |
| /* Receive NACK Inhibit */ |
| #define ASM9260_BM_ISO7816CTRL_INACK BIT(3) |
| #define ASM9260_BM_ISO7816CTRL_NEG_DATA BIT(2) |
| /* RW. 1 - ISO7816 mode; 0 - USART mode */ |
| #define ASM9260_BM_ISO7816CTRL_ENABLE BIT(0) |
| |
| #define ASM9260_HW_ISO7816_ERRCNT 0x00f0 |
| /* Parity error counter. Will be cleared after reading */ |
| #define ASM9260_BM_ISO7816_NB_ERRORS_MASK (0xff << 0) |
| |
| #define ASM9260_HW_ISO7816_STATUS 0x0100 |
| /* Max number of Repetitions Reached */ |
| #define ASM9260_BM_ISO7816_STAT_ITERATION BIT(0) |
| |
| /* End of Alphascale asm9260 defines */ |
| |
| static struct uart_driver auart_driver; |
| |
| enum mxs_auart_type { |
| IMX23_AUART, |
| IMX28_AUART, |
| ASM9260_AUART, |
| }; |
| |
| struct vendor_data { |
| const u16 *reg_offset; |
| }; |
| |
| enum { |
| REG_CTRL0, |
| REG_CTRL1, |
| REG_CTRL2, |
| REG_LINECTRL, |
| REG_LINECTRL2, |
| REG_INTR, |
| REG_DATA, |
| REG_STAT, |
| REG_DEBUG, |
| REG_VERSION, |
| REG_AUTOBAUD, |
| |
| /* The size of the array - must be last */ |
| REG_ARRAY_SIZE, |
| }; |
| |
| static const u16 mxs_asm9260_offsets[REG_ARRAY_SIZE] = { |
| [REG_CTRL0] = ASM9260_HW_CTRL0, |
| [REG_CTRL1] = ASM9260_HW_CTRL1, |
| [REG_CTRL2] = ASM9260_HW_CTRL2, |
| [REG_LINECTRL] = ASM9260_HW_LINECTRL, |
| [REG_INTR] = ASM9260_HW_INTR, |
| [REG_DATA] = ASM9260_HW_DATA, |
| [REG_STAT] = ASM9260_HW_STAT, |
| [REG_DEBUG] = ASM9260_HW_DEBUG, |
| [REG_AUTOBAUD] = ASM9260_HW_AUTOBAUD, |
| }; |
| |
| static const u16 mxs_stmp37xx_offsets[REG_ARRAY_SIZE] = { |
| [REG_CTRL0] = AUART_CTRL0, |
| [REG_CTRL1] = AUART_CTRL1, |
| [REG_CTRL2] = AUART_CTRL2, |
| [REG_LINECTRL] = AUART_LINECTRL, |
| [REG_LINECTRL2] = AUART_LINECTRL2, |
| [REG_INTR] = AUART_INTR, |
| [REG_DATA] = AUART_DATA, |
| [REG_STAT] = AUART_STAT, |
| [REG_DEBUG] = AUART_DEBUG, |
| [REG_VERSION] = AUART_VERSION, |
| [REG_AUTOBAUD] = AUART_AUTOBAUD, |
| }; |
| |
| static const struct vendor_data vendor_alphascale_asm9260 = { |
| .reg_offset = mxs_asm9260_offsets, |
| }; |
| |
| static const struct vendor_data vendor_freescale_stmp37xx = { |
| .reg_offset = mxs_stmp37xx_offsets, |
| }; |
| |
| struct mxs_auart_port { |
| struct uart_port port; |
| |
| #define MXS_AUART_DMA_ENABLED 0x2 |
| #define MXS_AUART_DMA_TX_SYNC 2 /* bit 2 */ |
| #define MXS_AUART_DMA_RX_READY 3 /* bit 3 */ |
| #define MXS_AUART_RTSCTS 4 /* bit 4 */ |
| unsigned long flags; |
| unsigned int mctrl_prev; |
| enum mxs_auart_type devtype; |
| const struct vendor_data *vendor; |
| |
| struct clk *clk; |
| struct clk *clk_ahb; |
| struct device *dev; |
| |
| /* for DMA */ |
| struct scatterlist tx_sgl; |
| struct dma_chan *tx_dma_chan; |
| void *tx_dma_buf; |
| |
| struct scatterlist rx_sgl; |
| struct dma_chan *rx_dma_chan; |
| void *rx_dma_buf; |
| |
| struct mctrl_gpios *gpios; |
| int gpio_irq[UART_GPIO_MAX]; |
| bool ms_irq_enabled; |
| }; |
| |
| static const struct platform_device_id mxs_auart_devtype[] = { |
| { .name = "mxs-auart-imx23", .driver_data = IMX23_AUART }, |
| { .name = "mxs-auart-imx28", .driver_data = IMX28_AUART }, |
| { .name = "as-auart-asm9260", .driver_data = ASM9260_AUART }, |
| { /* sentinel */ } |
| }; |
| MODULE_DEVICE_TABLE(platform, mxs_auart_devtype); |
| |
| static const struct of_device_id mxs_auart_dt_ids[] = { |
| { |
| .compatible = "fsl,imx28-auart", |
| .data = &mxs_auart_devtype[IMX28_AUART] |
| }, { |
| .compatible = "fsl,imx23-auart", |
| .data = &mxs_auart_devtype[IMX23_AUART] |
| }, { |
| .compatible = "alphascale,asm9260-auart", |
| .data = &mxs_auart_devtype[ASM9260_AUART] |
| }, { /* sentinel */ } |
| }; |
| MODULE_DEVICE_TABLE(of, mxs_auart_dt_ids); |
| |
| static inline int is_imx28_auart(struct mxs_auart_port *s) |
| { |
| return s->devtype == IMX28_AUART; |
| } |
| |
| static inline int is_asm9260_auart(struct mxs_auart_port *s) |
| { |
| return s->devtype == ASM9260_AUART; |
| } |
| |
| static inline bool auart_dma_enabled(struct mxs_auart_port *s) |
| { |
| return s->flags & MXS_AUART_DMA_ENABLED; |
| } |
| |
| static unsigned int mxs_reg_to_offset(const struct mxs_auart_port *uap, |
| unsigned int reg) |
| { |
| return uap->vendor->reg_offset[reg]; |
| } |
| |
| static unsigned int mxs_read(const struct mxs_auart_port *uap, |
| unsigned int reg) |
| { |
| void __iomem *addr = uap->port.membase + mxs_reg_to_offset(uap, reg); |
| |
| return readl_relaxed(addr); |
| } |
| |
| static void mxs_write(unsigned int val, struct mxs_auart_port *uap, |
| unsigned int reg) |
| { |
| void __iomem *addr = uap->port.membase + mxs_reg_to_offset(uap, reg); |
| |
| writel_relaxed(val, addr); |
| } |
| |
| static void mxs_set(unsigned int val, struct mxs_auart_port *uap, |
| unsigned int reg) |
| { |
| void __iomem *addr = uap->port.membase + mxs_reg_to_offset(uap, reg); |
| |
| writel_relaxed(val, addr + SET_REG); |
| } |
| |
| static void mxs_clr(unsigned int val, struct mxs_auart_port *uap, |
| unsigned int reg) |
| { |
| void __iomem *addr = uap->port.membase + mxs_reg_to_offset(uap, reg); |
| |
| writel_relaxed(val, addr + CLR_REG); |
| } |
| |
| static void mxs_auart_stop_tx(struct uart_port *u); |
| |
| #define to_auart_port(u) container_of(u, struct mxs_auart_port, port) |
| |
| static void mxs_auart_tx_chars(struct mxs_auart_port *s); |
| |
| static void dma_tx_callback(void *param) |
| { |
| struct mxs_auart_port *s = param; |
| struct circ_buf *xmit = &s->port.state->xmit; |
| |
| dma_unmap_sg(s->dev, &s->tx_sgl, 1, DMA_TO_DEVICE); |
| |
| /* clear the bit used to serialize the DMA tx. */ |
| clear_bit(MXS_AUART_DMA_TX_SYNC, &s->flags); |
| smp_mb__after_atomic(); |
| |
| /* wake up the possible processes. */ |
| if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) |
| uart_write_wakeup(&s->port); |
| |
| mxs_auart_tx_chars(s); |
| } |
| |
| static int mxs_auart_dma_tx(struct mxs_auart_port *s, int size) |
| { |
| struct dma_async_tx_descriptor *desc; |
| struct scatterlist *sgl = &s->tx_sgl; |
| struct dma_chan *channel = s->tx_dma_chan; |
| u32 pio; |
| |
| /* [1] : send PIO. Note, the first pio word is CTRL1. */ |
| pio = AUART_CTRL1_XFER_COUNT(size); |
| desc = dmaengine_prep_slave_sg(channel, (struct scatterlist *)&pio, |
| 1, DMA_TRANS_NONE, 0); |
| if (!desc) { |
| dev_err(s->dev, "step 1 error\n"); |
| return -EINVAL; |
| } |
| |
| /* [2] : set DMA buffer. */ |
| sg_init_one(sgl, s->tx_dma_buf, size); |
| dma_map_sg(s->dev, sgl, 1, DMA_TO_DEVICE); |
| desc = dmaengine_prep_slave_sg(channel, sgl, |
| 1, DMA_MEM_TO_DEV, DMA_PREP_INTERRUPT | DMA_CTRL_ACK); |
| if (!desc) { |
| dev_err(s->dev, "step 2 error\n"); |
| return -EINVAL; |
| } |
| |
| /* [3] : submit the DMA */ |
| desc->callback = dma_tx_callback; |
| desc->callback_param = s; |
| dmaengine_submit(desc); |
| dma_async_issue_pending(channel); |
| return 0; |
| } |
| |
| static void mxs_auart_tx_chars(struct mxs_auart_port *s) |
| { |
| struct circ_buf *xmit = &s->port.state->xmit; |
| |
| if (auart_dma_enabled(s)) { |
| u32 i = 0; |
| int size; |
| void *buffer = s->tx_dma_buf; |
| |
| if (test_and_set_bit(MXS_AUART_DMA_TX_SYNC, &s->flags)) |
| return; |
| |
| while (!uart_circ_empty(xmit) && !uart_tx_stopped(&s->port)) { |
| size = min_t(u32, UART_XMIT_SIZE - i, |
| CIRC_CNT_TO_END(xmit->head, |
| xmit->tail, |
| UART_XMIT_SIZE)); |
| memcpy(buffer + i, xmit->buf + xmit->tail, size); |
| xmit->tail = (xmit->tail + size) & (UART_XMIT_SIZE - 1); |
| |
| i += size; |
| if (i >= UART_XMIT_SIZE) |
| break; |
| } |
| |
| if (uart_tx_stopped(&s->port)) |
| mxs_auart_stop_tx(&s->port); |
| |
| if (i) { |
| mxs_auart_dma_tx(s, i); |
| } else { |
| clear_bit(MXS_AUART_DMA_TX_SYNC, &s->flags); |
| smp_mb__after_atomic(); |
| } |
| return; |
| } |
| |
| |
| while (!(mxs_read(s, REG_STAT) & AUART_STAT_TXFF)) { |
| if (s->port.x_char) { |
| s->port.icount.tx++; |
| mxs_write(s->port.x_char, s, REG_DATA); |
| s->port.x_char = 0; |
| continue; |
| } |
| if (!uart_circ_empty(xmit) && !uart_tx_stopped(&s->port)) { |
| s->port.icount.tx++; |
| mxs_write(xmit->buf[xmit->tail], s, REG_DATA); |
| xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); |
| } else |
| break; |
| } |
| if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) |
| uart_write_wakeup(&s->port); |
| |
| if (uart_circ_empty(&(s->port.state->xmit))) |
| mxs_clr(AUART_INTR_TXIEN, s, REG_INTR); |
| else |
| mxs_set(AUART_INTR_TXIEN, s, REG_INTR); |
| |
| if (uart_tx_stopped(&s->port)) |
| mxs_auart_stop_tx(&s->port); |
| } |
| |
| static void mxs_auart_rx_char(struct mxs_auart_port *s) |
| { |
| int flag; |
| u32 stat; |
| u8 c; |
| |
| c = mxs_read(s, REG_DATA); |
| stat = mxs_read(s, REG_STAT); |
| |
| flag = TTY_NORMAL; |
| s->port.icount.rx++; |
| |
| if (stat & AUART_STAT_BERR) { |
| s->port.icount.brk++; |
| if (uart_handle_break(&s->port)) |
| goto out; |
| } else if (stat & AUART_STAT_PERR) { |
| s->port.icount.parity++; |
| } else if (stat & AUART_STAT_FERR) { |
| s->port.icount.frame++; |
| } |
| |
| /* |
| * Mask off conditions which should be ingored. |
| */ |
| stat &= s->port.read_status_mask; |
| |
| if (stat & AUART_STAT_BERR) { |
| flag = TTY_BREAK; |
| } else if (stat & AUART_STAT_PERR) |
| flag = TTY_PARITY; |
| else if (stat & AUART_STAT_FERR) |
| flag = TTY_FRAME; |
| |
| if (stat & AUART_STAT_OERR) |
| s->port.icount.overrun++; |
| |
| if (uart_handle_sysrq_char(&s->port, c)) |
| goto out; |
| |
| uart_insert_char(&s->port, stat, AUART_STAT_OERR, c, flag); |
| out: |
| mxs_write(stat, s, REG_STAT); |
| } |
| |
| static void mxs_auart_rx_chars(struct mxs_auart_port *s) |
| { |
| u32 stat = 0; |
| |
| for (;;) { |
| stat = mxs_read(s, REG_STAT); |
| if (stat & AUART_STAT_RXFE) |
| break; |
| mxs_auart_rx_char(s); |
| } |
| |
| mxs_write(stat, s, REG_STAT); |
| tty_flip_buffer_push(&s->port.state->port); |
| } |
| |
| static int mxs_auart_request_port(struct uart_port *u) |
| { |
| return 0; |
| } |
| |
| static int mxs_auart_verify_port(struct uart_port *u, |
| struct serial_struct *ser) |
| { |
| if (u->type != PORT_UNKNOWN && u->type != PORT_IMX) |
| return -EINVAL; |
| return 0; |
| } |
| |
| static void mxs_auart_config_port(struct uart_port *u, int flags) |
| { |
| } |
| |
| static const char *mxs_auart_type(struct uart_port *u) |
| { |
| struct mxs_auart_port *s = to_auart_port(u); |
| |
| return dev_name(s->dev); |
| } |
| |
| static void mxs_auart_release_port(struct uart_port *u) |
| { |
| } |
| |
| static void mxs_auart_set_mctrl(struct uart_port *u, unsigned mctrl) |
| { |
| struct mxs_auart_port *s = to_auart_port(u); |
| |
| u32 ctrl = mxs_read(s, REG_CTRL2); |
| |
| ctrl &= ~(AUART_CTRL2_RTSEN | AUART_CTRL2_RTS); |
| if (mctrl & TIOCM_RTS) { |
| if (uart_cts_enabled(u)) |
| ctrl |= AUART_CTRL2_RTSEN; |
| else |
| ctrl |= AUART_CTRL2_RTS; |
| } |
| |
| mxs_write(ctrl, s, REG_CTRL2); |
| |
| mctrl_gpio_set(s->gpios, mctrl); |
| } |
| |
| #define MCTRL_ANY_DELTA (TIOCM_RI | TIOCM_DSR | TIOCM_CD | TIOCM_CTS) |
| static u32 mxs_auart_modem_status(struct mxs_auart_port *s, u32 mctrl) |
| { |
| u32 mctrl_diff; |
| |
| mctrl_diff = mctrl ^ s->mctrl_prev; |
| s->mctrl_prev = mctrl; |
| if (mctrl_diff & MCTRL_ANY_DELTA && s->ms_irq_enabled && |
| s->port.state != NULL) { |
| if (mctrl_diff & TIOCM_RI) |
| s->port.icount.rng++; |
| if (mctrl_diff & TIOCM_DSR) |
| s->port.icount.dsr++; |
| if (mctrl_diff & TIOCM_CD) |
| uart_handle_dcd_change(&s->port, mctrl & TIOCM_CD); |
| if (mctrl_diff & TIOCM_CTS) |
| uart_handle_cts_change(&s->port, mctrl & TIOCM_CTS); |
| |
| wake_up_interruptible(&s->port.state->port.delta_msr_wait); |
| } |
| return mctrl; |
| } |
| |
| static u32 mxs_auart_get_mctrl(struct uart_port *u) |
| { |
| struct mxs_auart_port *s = to_auart_port(u); |
| u32 stat = mxs_read(s, REG_STAT); |
| u32 mctrl = 0; |
| |
| if (stat & AUART_STAT_CTS) |
| mctrl |= TIOCM_CTS; |
| |
| return mctrl_gpio_get(s->gpios, &mctrl); |
| } |
| |
| /* |
| * Enable modem status interrupts |
| */ |
| static void mxs_auart_enable_ms(struct uart_port *port) |
| { |
| struct mxs_auart_port *s = to_auart_port(port); |
| |
| /* |
| * Interrupt should not be enabled twice |
| */ |
| if (s->ms_irq_enabled) |
| return; |
| |
| s->ms_irq_enabled = true; |
| |
| if (s->gpio_irq[UART_GPIO_CTS] >= 0) |
| enable_irq(s->gpio_irq[UART_GPIO_CTS]); |
| /* TODO: enable AUART_INTR_CTSMIEN otherwise */ |
| |
| if (s->gpio_irq[UART_GPIO_DSR] >= 0) |
| enable_irq(s->gpio_irq[UART_GPIO_DSR]); |
| |
| if (s->gpio_irq[UART_GPIO_RI] >= 0) |
| enable_irq(s->gpio_irq[UART_GPIO_RI]); |
| |
| if (s->gpio_irq[UART_GPIO_DCD] >= 0) |
| enable_irq(s->gpio_irq[UART_GPIO_DCD]); |
| } |
| |
| /* |
| * Disable modem status interrupts |
| */ |
| static void mxs_auart_disable_ms(struct uart_port *port) |
| { |
| struct mxs_auart_port *s = to_auart_port(port); |
| |
| /* |
| * Interrupt should not be disabled twice |
| */ |
| if (!s->ms_irq_enabled) |
| return; |
| |
| s->ms_irq_enabled = false; |
| |
| if (s->gpio_irq[UART_GPIO_CTS] >= 0) |
| disable_irq(s->gpio_irq[UART_GPIO_CTS]); |
| /* TODO: disable AUART_INTR_CTSMIEN otherwise */ |
| |
| if (s->gpio_irq[UART_GPIO_DSR] >= 0) |
| disable_irq(s->gpio_irq[UART_GPIO_DSR]); |
| |
| if (s->gpio_irq[UART_GPIO_RI] >= 0) |
| disable_irq(s->gpio_irq[UART_GPIO_RI]); |
| |
| if (s->gpio_irq[UART_GPIO_DCD] >= 0) |
| disable_irq(s->gpio_irq[UART_GPIO_DCD]); |
| } |
| |
| static int mxs_auart_dma_prep_rx(struct mxs_auart_port *s); |
| static void dma_rx_callback(void *arg) |
| { |
| struct mxs_auart_port *s = (struct mxs_auart_port *) arg; |
| struct tty_port *port = &s->port.state->port; |
| int count; |
| u32 stat; |
| |
| dma_unmap_sg(s->dev, &s->rx_sgl, 1, DMA_FROM_DEVICE); |
| |
| stat = mxs_read(s, REG_STAT); |
| stat &= ~(AUART_STAT_OERR | AUART_STAT_BERR | |
| AUART_STAT_PERR | AUART_STAT_FERR); |
| |
| count = stat & AUART_STAT_RXCOUNT_MASK; |
| tty_insert_flip_string(port, s->rx_dma_buf, count); |
| |
| mxs_write(stat, s, REG_STAT); |
| tty_flip_buffer_push(port); |
| |
| /* start the next DMA for RX. */ |
| mxs_auart_dma_prep_rx(s); |
| } |
| |
| static int mxs_auart_dma_prep_rx(struct mxs_auart_port *s) |
| { |
| struct dma_async_tx_descriptor *desc; |
| struct scatterlist *sgl = &s->rx_sgl; |
| struct dma_chan *channel = s->rx_dma_chan; |
| u32 pio[1]; |
| |
| /* [1] : send PIO */ |
| pio[0] = AUART_CTRL0_RXTO_ENABLE |
| | AUART_CTRL0_RXTIMEOUT(0x80) |
| | AUART_CTRL0_XFER_COUNT(UART_XMIT_SIZE); |
| desc = dmaengine_prep_slave_sg(channel, (struct scatterlist *)pio, |
| 1, DMA_TRANS_NONE, 0); |
| if (!desc) { |
| dev_err(s->dev, "step 1 error\n"); |
| return -EINVAL; |
| } |
| |
| /* [2] : send DMA request */ |
| sg_init_one(sgl, s->rx_dma_buf, UART_XMIT_SIZE); |
| dma_map_sg(s->dev, sgl, 1, DMA_FROM_DEVICE); |
| desc = dmaengine_prep_slave_sg(channel, sgl, 1, DMA_DEV_TO_MEM, |
| DMA_PREP_INTERRUPT | DMA_CTRL_ACK); |
| if (!desc) { |
| dev_err(s->dev, "step 2 error\n"); |
| return -1; |
| } |
| |
| /* [3] : submit the DMA, but do not issue it. */ |
| desc->callback = dma_rx_callback; |
| desc->callback_param = s; |
| dmaengine_submit(desc); |
| dma_async_issue_pending(channel); |
| return 0; |
| } |
| |
| static void mxs_auart_dma_exit_channel(struct mxs_auart_port *s) |
| { |
| if (s->tx_dma_chan) { |
| dma_release_channel(s->tx_dma_chan); |
| s->tx_dma_chan = NULL; |
| } |
| if (s->rx_dma_chan) { |
| dma_release_channel(s->rx_dma_chan); |
| s->rx_dma_chan = NULL; |
| } |
| |
| kfree(s->tx_dma_buf); |
| kfree(s->rx_dma_buf); |
| s->tx_dma_buf = NULL; |
| s->rx_dma_buf = NULL; |
| } |
| |
| static void mxs_auart_dma_exit(struct mxs_auart_port *s) |
| { |
| |
| mxs_clr(AUART_CTRL2_TXDMAE | AUART_CTRL2_RXDMAE | AUART_CTRL2_DMAONERR, |
| s, REG_CTRL2); |
| |
| mxs_auart_dma_exit_channel(s); |
| s->flags &= ~MXS_AUART_DMA_ENABLED; |
| clear_bit(MXS_AUART_DMA_TX_SYNC, &s->flags); |
| clear_bit(MXS_AUART_DMA_RX_READY, &s->flags); |
| } |
| |
| static int mxs_auart_dma_init(struct mxs_auart_port *s) |
| { |
| if (auart_dma_enabled(s)) |
| return 0; |
| |
| /* init for RX */ |
| s->rx_dma_chan = dma_request_slave_channel(s->dev, "rx"); |
| if (!s->rx_dma_chan) |
| goto err_out; |
| s->rx_dma_buf = kzalloc(UART_XMIT_SIZE, GFP_KERNEL | GFP_DMA); |
| if (!s->rx_dma_buf) |
| goto err_out; |
| |
| /* init for TX */ |
| s->tx_dma_chan = dma_request_slave_channel(s->dev, "tx"); |
| if (!s->tx_dma_chan) |
| goto err_out; |
| s->tx_dma_buf = kzalloc(UART_XMIT_SIZE, GFP_KERNEL | GFP_DMA); |
| if (!s->tx_dma_buf) |
| goto err_out; |
| |
| /* set the flags */ |
| s->flags |= MXS_AUART_DMA_ENABLED; |
| dev_dbg(s->dev, "enabled the DMA support."); |
| |
| /* The DMA buffer is now the FIFO the TTY subsystem can use */ |
| s->port.fifosize = UART_XMIT_SIZE; |
| |
| return 0; |
| |
| err_out: |
| mxs_auart_dma_exit_channel(s); |
| return -EINVAL; |
| |
| } |
| |
| #define RTS_AT_AUART() IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(s->gpios, \ |
| UART_GPIO_RTS)) |
| #define CTS_AT_AUART() IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(s->gpios, \ |
| UART_GPIO_CTS)) |
| static void mxs_auart_settermios(struct uart_port *u, |
| struct ktermios *termios, |
| struct ktermios *old) |
| { |
| struct mxs_auart_port *s = to_auart_port(u); |
| u32 bm, ctrl, ctrl2, div; |
| unsigned int cflag, baud, baud_min, baud_max; |
| |
| cflag = termios->c_cflag; |
| |
| ctrl = AUART_LINECTRL_FEN; |
| ctrl2 = mxs_read(s, REG_CTRL2); |
| |
| /* byte size */ |
| switch (cflag & CSIZE) { |
| case CS5: |
| bm = 0; |
| break; |
| case CS6: |
| bm = 1; |
| break; |
| case CS7: |
| bm = 2; |
| break; |
| case CS8: |
| bm = 3; |
| break; |
| default: |
| return; |
| } |
| |
| ctrl |= AUART_LINECTRL_WLEN(bm); |
| |
| /* parity */ |
| if (cflag & PARENB) { |
| ctrl |= AUART_LINECTRL_PEN; |
| if ((cflag & PARODD) == 0) |
| ctrl |= AUART_LINECTRL_EPS; |
| if (cflag & CMSPAR) |
| ctrl |= AUART_LINECTRL_SPS; |
| } |
| |
| u->read_status_mask = AUART_STAT_OERR; |
| |
| if (termios->c_iflag & INPCK) |
| u->read_status_mask |= AUART_STAT_PERR; |
| if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) |
| u->read_status_mask |= AUART_STAT_BERR; |
| |
| /* |
| * Characters to ignore |
| */ |
| u->ignore_status_mask = 0; |
| if (termios->c_iflag & IGNPAR) |
| u->ignore_status_mask |= AUART_STAT_PERR; |
| if (termios->c_iflag & IGNBRK) { |
| u->ignore_status_mask |= AUART_STAT_BERR; |
| /* |
| * If we're ignoring parity and break indicators, |
| * ignore overruns too (for real raw support). |
| */ |
| if (termios->c_iflag & IGNPAR) |
| u->ignore_status_mask |= AUART_STAT_OERR; |
| } |
| |
| /* |
| * ignore all characters if CREAD is not set |
| */ |
| if (cflag & CREAD) |
| ctrl2 |= AUART_CTRL2_RXE; |
| else |
| ctrl2 &= ~AUART_CTRL2_RXE; |
| |
| /* figure out the stop bits requested */ |
| if (cflag & CSTOPB) |
| ctrl |= AUART_LINECTRL_STP2; |
| |
| /* figure out the hardware flow control settings */ |
| ctrl2 &= ~(AUART_CTRL2_CTSEN | AUART_CTRL2_RTSEN); |
| if (cflag & CRTSCTS) { |
| /* |
| * The DMA has a bug(see errata:2836) in mx23. |
| * So we can not implement the DMA for auart in mx23, |
| * we can only implement the DMA support for auart |
| * in mx28. |
| */ |
| if (is_imx28_auart(s) |
| && test_bit(MXS_AUART_RTSCTS, &s->flags)) { |
| if (!mxs_auart_dma_init(s)) |
| /* enable DMA tranfer */ |
| ctrl2 |= AUART_CTRL2_TXDMAE | AUART_CTRL2_RXDMAE |
| | AUART_CTRL2_DMAONERR; |
| } |
| /* Even if RTS is GPIO line RTSEN can be enabled because |
| * the pinctrl configuration decides about RTS pin function */ |
| ctrl2 |= AUART_CTRL2_RTSEN; |
| if (CTS_AT_AUART()) |
| ctrl2 |= AUART_CTRL2_CTSEN; |
| } |
| |
| /* set baud rate */ |
| if (is_asm9260_auart(s)) { |
| baud = uart_get_baud_rate(u, termios, old, |
| u->uartclk * 4 / 0x3FFFFF, |
| u->uartclk / 16); |
| div = u->uartclk * 4 / baud; |
| } else { |
| baud_min = DIV_ROUND_UP(u->uartclk * 32, |
| AUART_LINECTRL_BAUD_DIV_MAX); |
| baud_max = u->uartclk * 32 / AUART_LINECTRL_BAUD_DIV_MIN; |
| baud = uart_get_baud_rate(u, termios, old, baud_min, baud_max); |
| div = DIV_ROUND_CLOSEST(u->uartclk * 32, baud); |
| } |
| |
| ctrl |= AUART_LINECTRL_BAUD_DIVFRAC(div & 0x3F); |
| ctrl |= AUART_LINECTRL_BAUD_DIVINT(div >> 6); |
| mxs_write(ctrl, s, REG_LINECTRL); |
| |
| mxs_write(ctrl2, s, REG_CTRL2); |
| |
| uart_update_timeout(u, termios->c_cflag, baud); |
| |
| /* prepare for the DMA RX. */ |
| if (auart_dma_enabled(s) && |
| !test_and_set_bit(MXS_AUART_DMA_RX_READY, &s->flags)) { |
| if (!mxs_auart_dma_prep_rx(s)) { |
| /* Disable the normal RX interrupt. */ |
| mxs_clr(AUART_INTR_RXIEN | AUART_INTR_RTIEN, |
| s, REG_INTR); |
| } else { |
| mxs_auart_dma_exit(s); |
| dev_err(s->dev, "We can not start up the DMA.\n"); |
| } |
| } |
| |
| /* CTS flow-control and modem-status interrupts */ |
| if (UART_ENABLE_MS(u, termios->c_cflag)) |
| mxs_auart_enable_ms(u); |
| else |
| mxs_auart_disable_ms(u); |
| } |
| |
| static void mxs_auart_set_ldisc(struct uart_port *port, |
| struct ktermios *termios) |
| { |
| if (termios->c_line == N_PPS) { |
| port->flags |= UPF_HARDPPS_CD; |
| mxs_auart_enable_ms(port); |
| } else { |
| port->flags &= ~UPF_HARDPPS_CD; |
| } |
| } |
| |
| static irqreturn_t mxs_auart_irq_handle(int irq, void *context) |
| { |
| u32 istat; |
| struct mxs_auart_port *s = context; |
| u32 mctrl_temp = s->mctrl_prev; |
| u32 stat = mxs_read(s, REG_STAT); |
| |
| istat = mxs_read(s, REG_INTR); |
| |
| /* ack irq */ |
| mxs_clr(istat & (AUART_INTR_RTIS | AUART_INTR_TXIS | AUART_INTR_RXIS |
| | AUART_INTR_CTSMIS), s, REG_INTR); |
| |
| /* |
| * Dealing with GPIO interrupt |
| */ |
| if (irq == s->gpio_irq[UART_GPIO_CTS] || |
| irq == s->gpio_irq[UART_GPIO_DCD] || |
| irq == s->gpio_irq[UART_GPIO_DSR] || |
| irq == s->gpio_irq[UART_GPIO_RI]) |
| mxs_auart_modem_status(s, |
| mctrl_gpio_get(s->gpios, &mctrl_temp)); |
| |
| if (istat & AUART_INTR_CTSMIS) { |
| if (CTS_AT_AUART() && s->ms_irq_enabled) |
| uart_handle_cts_change(&s->port, |
| stat & AUART_STAT_CTS); |
| mxs_clr(AUART_INTR_CTSMIS, s, REG_INTR); |
| istat &= ~AUART_INTR_CTSMIS; |
| } |
| |
| if (istat & (AUART_INTR_RTIS | AUART_INTR_RXIS)) { |
| if (!auart_dma_enabled(s)) |
| mxs_auart_rx_chars(s); |
| istat &= ~(AUART_INTR_RTIS | AUART_INTR_RXIS); |
| } |
| |
| if (istat & AUART_INTR_TXIS) { |
| mxs_auart_tx_chars(s); |
| istat &= ~AUART_INTR_TXIS; |
| } |
| |
| return IRQ_HANDLED; |
| } |
| |
| static void mxs_auart_reset_deassert(struct mxs_auart_port *s) |
| { |
| int i; |
| unsigned int reg; |
| |
| mxs_clr(AUART_CTRL0_SFTRST, s, REG_CTRL0); |
| |
| for (i = 0; i < 10000; i++) { |
| reg = mxs_read(s, REG_CTRL0); |
| if (!(reg & AUART_CTRL0_SFTRST)) |
| break; |
| udelay(3); |
| } |
| mxs_clr(AUART_CTRL0_CLKGATE, s, REG_CTRL0); |
| } |
| |
| static void mxs_auart_reset_assert(struct mxs_auart_port *s) |
| { |
| int i; |
| u32 reg; |
| |
| reg = mxs_read(s, REG_CTRL0); |
| /* if already in reset state, keep it untouched */ |
| if (reg & AUART_CTRL0_SFTRST) |
| return; |
| |
| mxs_clr(AUART_CTRL0_CLKGATE, s, REG_CTRL0); |
| mxs_set(AUART_CTRL0_SFTRST, s, REG_CTRL0); |
| |
| for (i = 0; i < 1000; i++) { |
| reg = mxs_read(s, REG_CTRL0); |
| /* reset is finished when the clock is gated */ |
| if (reg & AUART_CTRL0_CLKGATE) |
| return; |
| udelay(10); |
| } |
| |
| dev_err(s->dev, "Failed to reset the unit."); |
| } |
| |
| static int mxs_auart_startup(struct uart_port *u) |
| { |
| int ret; |
| struct mxs_auart_port *s = to_auart_port(u); |
| |
| ret = clk_prepare_enable(s->clk); |
| if (ret) |
| return ret; |
| |
| if (uart_console(u)) { |
| mxs_clr(AUART_CTRL0_CLKGATE, s, REG_CTRL0); |
| } else { |
| /* reset the unit to a well known state */ |
| mxs_auart_reset_assert(s); |
| mxs_auart_reset_deassert(s); |
| } |
| |
| mxs_set(AUART_CTRL2_UARTEN, s, REG_CTRL2); |
| |
| mxs_write(AUART_INTR_RXIEN | AUART_INTR_RTIEN | AUART_INTR_CTSMIEN, |
| s, REG_INTR); |
| |
| /* Reset FIFO size (it could have changed if DMA was enabled) */ |
| u->fifosize = MXS_AUART_FIFO_SIZE; |
| |
| /* |
| * Enable fifo so all four bytes of a DMA word are written to |
| * output (otherwise, only the LSB is written, ie. 1 in 4 bytes) |
| */ |
| mxs_set(AUART_LINECTRL_FEN, s, REG_LINECTRL); |
| |
| /* get initial status of modem lines */ |
| mctrl_gpio_get(s->gpios, &s->mctrl_prev); |
| |
| s->ms_irq_enabled = false; |
| return 0; |
| } |
| |
| static void mxs_auart_shutdown(struct uart_port *u) |
| { |
| struct mxs_auart_port *s = to_auart_port(u); |
| |
| mxs_auart_disable_ms(u); |
| |
| if (auart_dma_enabled(s)) |
| mxs_auart_dma_exit(s); |
| |
| if (uart_console(u)) { |
| mxs_clr(AUART_CTRL2_UARTEN, s, REG_CTRL2); |
| |
| mxs_clr(AUART_INTR_RXIEN | AUART_INTR_RTIEN | |
| AUART_INTR_CTSMIEN, s, REG_INTR); |
| mxs_set(AUART_CTRL0_CLKGATE, s, REG_CTRL0); |
| } else { |
| mxs_auart_reset_assert(s); |
| } |
| |
| clk_disable_unprepare(s->clk); |
| } |
| |
| static unsigned int mxs_auart_tx_empty(struct uart_port *u) |
| { |
| struct mxs_auart_port *s = to_auart_port(u); |
| |
| if ((mxs_read(s, REG_STAT) & |
| (AUART_STAT_TXFE | AUART_STAT_BUSY)) == AUART_STAT_TXFE) |
| return TIOCSER_TEMT; |
| |
| return 0; |
| } |
| |
| static void mxs_auart_start_tx(struct uart_port *u) |
| { |
| struct mxs_auart_port *s = to_auart_port(u); |
| |
| /* enable transmitter */ |
| mxs_set(AUART_CTRL2_TXE, s, REG_CTRL2); |
| |
| mxs_auart_tx_chars(s); |
| } |
| |
| static void mxs_auart_stop_tx(struct uart_port *u) |
| { |
| struct mxs_auart_port *s = to_auart_port(u); |
| |
| mxs_clr(AUART_CTRL2_TXE, s, REG_CTRL2); |
| } |
| |
| static void mxs_auart_stop_rx(struct uart_port *u) |
| { |
| struct mxs_auart_port *s = to_auart_port(u); |
| |
| mxs_clr(AUART_CTRL2_RXE, s, REG_CTRL2); |
| } |
| |
| static void mxs_auart_break_ctl(struct uart_port *u, int ctl) |
| { |
| struct mxs_auart_port *s = to_auart_port(u); |
| |
| if (ctl) |
| mxs_set(AUART_LINECTRL_BRK, s, REG_LINECTRL); |
| else |
| mxs_clr(AUART_LINECTRL_BRK, s, REG_LINECTRL); |
| } |
| |
| static const struct uart_ops mxs_auart_ops = { |
| .tx_empty = mxs_auart_tx_empty, |
| .start_tx = mxs_auart_start_tx, |
| .stop_tx = mxs_auart_stop_tx, |
| .stop_rx = mxs_auart_stop_rx, |
| .enable_ms = mxs_auart_enable_ms, |
| .break_ctl = mxs_auart_break_ctl, |
| .set_mctrl = mxs_auart_set_mctrl, |
| .get_mctrl = mxs_auart_get_mctrl, |
| .startup = mxs_auart_startup, |
| .shutdown = mxs_auart_shutdown, |
| .set_termios = mxs_auart_settermios, |
| .set_ldisc = mxs_auart_set_ldisc, |
| .type = mxs_auart_type, |
| .release_port = mxs_auart_release_port, |
| .request_port = mxs_auart_request_port, |
| .config_port = mxs_auart_config_port, |
| .verify_port = mxs_auart_verify_port, |
| }; |
| |
| static struct mxs_auart_port *auart_port[MXS_AUART_PORTS]; |
| |
| #ifdef CONFIG_SERIAL_MXS_AUART_CONSOLE |
| static void mxs_auart_console_putchar(struct uart_port *port, int ch) |
| { |
| struct mxs_auart_port *s = to_auart_port(port); |
| unsigned int to = 1000; |
| |
| while (mxs_read(s, REG_STAT) & AUART_STAT_TXFF) { |
| if (!to--) |
| break; |
| udelay(1); |
| } |
| |
| mxs_write(ch, s, REG_DATA); |
| } |
| |
| static void |
| auart_console_write(struct console *co, const char *str, unsigned int count) |
| { |
| struct mxs_auart_port *s; |
| struct uart_port *port; |
| unsigned int old_ctrl0, old_ctrl2; |
| unsigned int to = 20000; |
| |
| if (co->index >= MXS_AUART_PORTS || co->index < 0) |
| return; |
| |
| s = auart_port[co->index]; |
| port = &s->port; |
| |
| clk_enable(s->clk); |
| |
| /* First save the CR then disable the interrupts */ |
| old_ctrl2 = mxs_read(s, REG_CTRL2); |
| old_ctrl0 = mxs_read(s, REG_CTRL0); |
| |
| mxs_clr(AUART_CTRL0_CLKGATE, s, REG_CTRL0); |
| mxs_set(AUART_CTRL2_UARTEN | AUART_CTRL2_TXE, s, REG_CTRL2); |
| |
| uart_console_write(port, str, count, mxs_auart_console_putchar); |
| |
| /* Finally, wait for transmitter to become empty ... */ |
| while (mxs_read(s, REG_STAT) & AUART_STAT_BUSY) { |
| udelay(1); |
| if (!to--) |
| break; |
| } |
| |
| /* |
| * ... and restore the TCR if we waited long enough for the transmitter |
| * to be idle. This might keep the transmitter enabled although it is |
| * unused, but that is better than to disable it while it is still |
| * transmitting. |
| */ |
| if (!(mxs_read(s, REG_STAT) & AUART_STAT_BUSY)) { |
| mxs_write(old_ctrl0, s, REG_CTRL0); |
| mxs_write(old_ctrl2, s, REG_CTRL2); |
| } |
| |
| clk_disable(s->clk); |
| } |
| |
| static void __init |
| auart_console_get_options(struct mxs_auart_port *s, int *baud, |
| int *parity, int *bits) |
| { |
| struct uart_port *port = &s->port; |
| unsigned int lcr_h, quot; |
| |
| if (!(mxs_read(s, REG_CTRL2) & AUART_CTRL2_UARTEN)) |
| return; |
| |
| lcr_h = mxs_read(s, REG_LINECTRL); |
| |
| *parity = 'n'; |
| if (lcr_h & AUART_LINECTRL_PEN) { |
| if (lcr_h & AUART_LINECTRL_EPS) |
| *parity = 'e'; |
| else |
| *parity = 'o'; |
| } |
| |
| if ((lcr_h & AUART_LINECTRL_WLEN_MASK) == AUART_LINECTRL_WLEN(2)) |
| *bits = 7; |
| else |
| *bits = 8; |
| |
| quot = ((mxs_read(s, REG_LINECTRL) & AUART_LINECTRL_BAUD_DIVINT_MASK)) |
| >> (AUART_LINECTRL_BAUD_DIVINT_SHIFT - 6); |
| quot |= ((mxs_read(s, REG_LINECTRL) & AUART_LINECTRL_BAUD_DIVFRAC_MASK)) |
| >> AUART_LINECTRL_BAUD_DIVFRAC_SHIFT; |
| if (quot == 0) |
| quot = 1; |
| |
| *baud = (port->uartclk << 2) / quot; |
| } |
| |
| static int __init |
| auart_console_setup(struct console *co, char *options) |
| { |
| struct mxs_auart_port *s; |
| int baud = 9600; |
| int bits = 8; |
| int parity = 'n'; |
| int flow = 'n'; |
| int ret; |
| |
| /* |
| * Check whether an invalid uart number has been specified, and |
| * if so, search for the first available port that does have |
| * console support. |
| */ |
| if (co->index == -1 || co->index >= ARRAY_SIZE(auart_port)) |
| co->index = 0; |
| s = auart_port[co->index]; |
| if (!s) |
| return -ENODEV; |
| |
| ret = clk_prepare_enable(s->clk); |
| if (ret) |
| return ret; |
| |
| if (options) |
| uart_parse_options(options, &baud, &parity, &bits, &flow); |
| else |
| auart_console_get_options(s, &baud, &parity, &bits); |
| |
| ret = uart_set_options(&s->port, co, baud, parity, bits, flow); |
| |
| clk_disable_unprepare(s->clk); |
| |
| return ret; |
| } |
| |
| static struct console auart_console = { |
| .name = "ttyAPP", |
| .write = auart_console_write, |
| .device = uart_console_device, |
| .setup = auart_console_setup, |
| .flags = CON_PRINTBUFFER, |
| .index = -1, |
| .data = &auart_driver, |
| }; |
| #endif |
| |
| static struct uart_driver auart_driver = { |
| .owner = THIS_MODULE, |
| .driver_name = "ttyAPP", |
| .dev_name = "ttyAPP", |
| .major = 0, |
| .minor = 0, |
| .nr = MXS_AUART_PORTS, |
| #ifdef CONFIG_SERIAL_MXS_AUART_CONSOLE |
| .cons = &auart_console, |
| #endif |
| }; |
| |
| static void mxs_init_regs(struct mxs_auart_port *s) |
| { |
| if (is_asm9260_auart(s)) |
| s->vendor = &vendor_alphascale_asm9260; |
| else |
| s->vendor = &vendor_freescale_stmp37xx; |
| } |
| |
| static int mxs_get_clks(struct mxs_auart_port *s, |
| struct platform_device *pdev) |
| { |
| int err; |
| |
| if (!is_asm9260_auart(s)) { |
| s->clk = devm_clk_get(&pdev->dev, NULL); |
| return PTR_ERR_OR_ZERO(s->clk); |
| } |
| |
| s->clk = devm_clk_get(s->dev, "mod"); |
| if (IS_ERR(s->clk)) { |
| dev_err(s->dev, "Failed to get \"mod\" clk\n"); |
| return PTR_ERR(s->clk); |
| } |
| |
| s->clk_ahb = devm_clk_get(s->dev, "ahb"); |
| if (IS_ERR(s->clk_ahb)) { |
| dev_err(s->dev, "Failed to get \"ahb\" clk\n"); |
| return PTR_ERR(s->clk_ahb); |
| } |
| |
| err = clk_prepare_enable(s->clk_ahb); |
| if (err) { |
| dev_err(s->dev, "Failed to enable ahb_clk!\n"); |
| return err; |
| } |
| |
| err = clk_set_rate(s->clk, clk_get_rate(s->clk_ahb)); |
| if (err) { |
| dev_err(s->dev, "Failed to set rate!\n"); |
| goto disable_clk_ahb; |
| } |
| |
| err = clk_prepare_enable(s->clk); |
| if (err) { |
| dev_err(s->dev, "Failed to enable clk!\n"); |
| goto disable_clk_ahb; |
| } |
| |
| return 0; |
| |
| disable_clk_ahb: |
| clk_disable_unprepare(s->clk_ahb); |
| return err; |
| } |
| |
| /* |
| * This function returns 1 if pdev isn't a device instatiated by dt, 0 if it |
| * could successfully get all information from dt or a negative errno. |
| */ |
| static int serial_mxs_probe_dt(struct mxs_auart_port *s, |
| struct platform_device *pdev) |
| { |
| struct device_node *np = pdev->dev.of_node; |
| int ret; |
| |
| if (!np) |
| /* no device tree device */ |
| return 1; |
| |
| ret = of_alias_get_id(np, "serial"); |
| if (ret < 0) { |
| dev_err(&pdev->dev, "failed to get alias id: %d\n", ret); |
| return ret; |
| } |
| s->port.line = ret; |
| |
| if (of_get_property(np, "uart-has-rtscts", NULL) || |
| of_get_property(np, "fsl,uart-has-rtscts", NULL) /* deprecated */) |
| set_bit(MXS_AUART_RTSCTS, &s->flags); |
| |
| return 0; |
| } |
| |
| static int mxs_auart_init_gpios(struct mxs_auart_port *s, struct device *dev) |
| { |
| enum mctrl_gpio_idx i; |
| struct gpio_desc *gpiod; |
| |
| s->gpios = mctrl_gpio_init_noauto(dev, 0); |
| if (IS_ERR(s->gpios)) |
| return PTR_ERR(s->gpios); |
| |
| /* Block (enabled before) DMA option if RTS or CTS is GPIO line */ |
| if (!RTS_AT_AUART() || !CTS_AT_AUART()) { |
| if (test_bit(MXS_AUART_RTSCTS, &s->flags)) |
| dev_warn(dev, |
| "DMA and flow control via gpio may cause some problems. DMA disabled!\n"); |
| clear_bit(MXS_AUART_RTSCTS, &s->flags); |
| } |
| |
| for (i = 0; i < UART_GPIO_MAX; i++) { |
| gpiod = mctrl_gpio_to_gpiod(s->gpios, i); |
| if (gpiod && (gpiod_get_direction(gpiod) == 1)) |
| s->gpio_irq[i] = gpiod_to_irq(gpiod); |
| else |
| s->gpio_irq[i] = -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static void mxs_auart_free_gpio_irq(struct mxs_auart_port *s) |
| { |
| enum mctrl_gpio_idx i; |
| |
| for (i = 0; i < UART_GPIO_MAX; i++) |
| if (s->gpio_irq[i] >= 0) |
| free_irq(s->gpio_irq[i], s); |
| } |
| |
| static int mxs_auart_request_gpio_irq(struct mxs_auart_port *s) |
| { |
| int *irq = s->gpio_irq; |
| enum mctrl_gpio_idx i; |
| int err = 0; |
| |
| for (i = 0; (i < UART_GPIO_MAX) && !err; i++) { |
| if (irq[i] < 0) |
| continue; |
| |
| irq_set_status_flags(irq[i], IRQ_NOAUTOEN); |
| err = request_irq(irq[i], mxs_auart_irq_handle, |
| IRQ_TYPE_EDGE_BOTH, dev_name(s->dev), s); |
| if (err) |
| dev_err(s->dev, "%s - Can't get %d irq\n", |
| __func__, irq[i]); |
| } |
| |
| /* |
| * If something went wrong, rollback. |
| * Be careful: i may be unsigned. |
| */ |
| while (err && (i-- > 0)) |
| if (irq[i] >= 0) |
| free_irq(irq[i], s); |
| |
| return err; |
| } |
| |
| static int mxs_auart_probe(struct platform_device *pdev) |
| { |
| const struct of_device_id *of_id = |
| of_match_device(mxs_auart_dt_ids, &pdev->dev); |
| struct mxs_auart_port *s; |
| u32 version; |
| int ret, irq; |
| struct resource *r; |
| |
| s = devm_kzalloc(&pdev->dev, sizeof(*s), GFP_KERNEL); |
| if (!s) |
| return -ENOMEM; |
| |
| s->port.dev = &pdev->dev; |
| s->dev = &pdev->dev; |
| |
| ret = serial_mxs_probe_dt(s, pdev); |
| if (ret > 0) |
| s->port.line = pdev->id < 0 ? 0 : pdev->id; |
| else if (ret < 0) |
| return ret; |
| if (s->port.line >= ARRAY_SIZE(auart_port)) { |
| dev_err(&pdev->dev, "serial%d out of range\n", s->port.line); |
| return -EINVAL; |
| } |
| |
| if (of_id) { |
| pdev->id_entry = of_id->data; |
| s->devtype = pdev->id_entry->driver_data; |
| } |
| |
| ret = mxs_get_clks(s, pdev); |
| if (ret) |
| return ret; |
| |
| r = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| if (!r) { |
| ret = -ENXIO; |
| goto out_disable_clks; |
| } |
| |
| s->port.mapbase = r->start; |
| s->port.membase = ioremap(r->start, resource_size(r)); |
| if (!s->port.membase) { |
| ret = -ENOMEM; |
| goto out_disable_clks; |
| } |
| s->port.ops = &mxs_auart_ops; |
| s->port.iotype = UPIO_MEM; |
| s->port.fifosize = MXS_AUART_FIFO_SIZE; |
| s->port.uartclk = clk_get_rate(s->clk); |
| s->port.type = PORT_IMX; |
| |
| mxs_init_regs(s); |
| |
| s->mctrl_prev = 0; |
| |
| irq = platform_get_irq(pdev, 0); |
| if (irq < 0) { |
| ret = irq; |
| goto out_iounmap; |
| } |
| |
| s->port.irq = irq; |
| ret = devm_request_irq(&pdev->dev, irq, mxs_auart_irq_handle, 0, |
| dev_name(&pdev->dev), s); |
| if (ret) |
| goto out_iounmap; |
| |
| platform_set_drvdata(pdev, s); |
| |
| ret = mxs_auart_init_gpios(s, &pdev->dev); |
| if (ret) { |
| dev_err(&pdev->dev, "Failed to initialize GPIOs.\n"); |
| goto out_iounmap; |
| } |
| |
| /* |
| * Get the GPIO lines IRQ |
| */ |
| ret = mxs_auart_request_gpio_irq(s); |
| if (ret) |
| goto out_iounmap; |
| |
| auart_port[s->port.line] = s; |
| |
| mxs_auart_reset_deassert(s); |
| |
| ret = uart_add_one_port(&auart_driver, &s->port); |
| if (ret) |
| goto out_free_qpio_irq; |
| |
| /* ASM9260 don't have version reg */ |
| if (is_asm9260_auart(s)) { |
| dev_info(&pdev->dev, "Found APPUART ASM9260\n"); |
| } else { |
| version = mxs_read(s, REG_VERSION); |
| dev_info(&pdev->dev, "Found APPUART %d.%d.%d\n", |
| (version >> 24) & 0xff, |
| (version >> 16) & 0xff, version & 0xffff); |
| } |
| |
| return 0; |
| |
| out_free_qpio_irq: |
| mxs_auart_free_gpio_irq(s); |
| auart_port[pdev->id] = NULL; |
| |
| out_iounmap: |
| iounmap(s->port.membase); |
| |
| out_disable_clks: |
| if (is_asm9260_auart(s)) { |
| clk_disable_unprepare(s->clk); |
| clk_disable_unprepare(s->clk_ahb); |
| } |
| return ret; |
| } |
| |
| static int mxs_auart_remove(struct platform_device *pdev) |
| { |
| struct mxs_auart_port *s = platform_get_drvdata(pdev); |
| |
| uart_remove_one_port(&auart_driver, &s->port); |
| auart_port[pdev->id] = NULL; |
| mxs_auart_free_gpio_irq(s); |
| iounmap(s->port.membase); |
| if (is_asm9260_auart(s)) { |
| clk_disable_unprepare(s->clk); |
| clk_disable_unprepare(s->clk_ahb); |
| } |
| |
| return 0; |
| } |
| |
| static struct platform_driver mxs_auart_driver = { |
| .probe = mxs_auart_probe, |
| .remove = mxs_auart_remove, |
| .driver = { |
| .name = "mxs-auart", |
| .of_match_table = mxs_auart_dt_ids, |
| }, |
| }; |
| |
| static int __init mxs_auart_init(void) |
| { |
| int r; |
| |
| r = uart_register_driver(&auart_driver); |
| if (r) |
| goto out; |
| |
| r = platform_driver_register(&mxs_auart_driver); |
| if (r) |
| goto out_err; |
| |
| return 0; |
| out_err: |
| uart_unregister_driver(&auart_driver); |
| out: |
| return r; |
| } |
| |
| static void __exit mxs_auart_exit(void) |
| { |
| platform_driver_unregister(&mxs_auart_driver); |
| uart_unregister_driver(&auart_driver); |
| } |
| |
| module_init(mxs_auart_init); |
| module_exit(mxs_auart_exit); |
| MODULE_LICENSE("GPL"); |
| MODULE_DESCRIPTION("Freescale MXS application uart driver"); |
| MODULE_ALIAS("platform:mxs-auart"); |