// SPDX-License-Identifier: (GPL-2.0+ OR MIT)

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/rockchip.h>
#include <dt-bindings/clock/rk3036-cru.h>
#include <dt-bindings/soc/rockchip,boot-mode.h>

/ {
	#address-cells = <1>;
	#size-cells = <1>;

	compatible = "rockchip,rk3036";

	interrupt-parent = <&gic>;

	aliases {
		i2c0 = &i2c0;
		i2c1 = &i2c1;
		i2c2 = &i2c2;
		mshc0 = &emmc;
		mshc1 = &sdmmc;
		mshc2 = &sdio;
		serial0 = &uart0;
		serial1 = &uart1;
		serial2 = &uart2;
		spi = &spi;
	};

	cpus {
		#address-cells = <1>;
		#size-cells = <0>;
		enable-method = "rockchip,rk3036-smp";

		cpu0: cpu@f00 {
			device_type = "cpu";
			compatible = "arm,cortex-a7";
			reg = <0xf00>;
			resets = <&cru SRST_CORE0>;
			operating-points = <
				/* KHz    uV */
				 816000 1000000
			>;
			clock-latency = <40000>;
			clocks = <&cru ARMCLK>;
		};

		cpu1: cpu@f01 {
			device_type = "cpu";
			compatible = "arm,cortex-a7";
			reg = <0xf01>;
			resets = <&cru SRST_CORE1>;
		};
	};

	amba {
		compatible = "simple-bus";
		#address-cells = <1>;
		#size-cells = <1>;
		ranges;

		pdma: pdma@20078000 {
			compatible = "arm,pl330", "arm,primecell";
			reg = <0x20078000 0x4000>;
			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
			#dma-cells = <1>;
			arm,pl330-broken-no-flushp;
			clocks = <&cru ACLK_DMAC2>;
			clock-names = "apb_pclk";
		};
	};

	arm-pmu {
		compatible = "arm,cortex-a7-pmu";
		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-affinity = <&cpu0>, <&cpu1>;
	};

	display-subsystem {
		compatible = "rockchip,display-subsystem";
		ports = <&vop_out>;
	};

	timer {
		compatible = "arm,armv7-timer";
		arm,cpu-registers-not-fw-configured;
		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>,
			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>,
			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>,
			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
		clock-frequency = <24000000>;
	};

	xin24m: oscillator {
		compatible = "fixed-clock";
		clock-frequency = <24000000>;
		clock-output-names = "xin24m";
		#clock-cells = <0>;
	};

	bus_intmem@10080000 {
		compatible = "mmio-sram";
		reg = <0x10080000 0x2000>;
		#address-cells = <1>;
		#size-cells = <1>;
		ranges = <0 0x10080000 0x2000>;

		smp-sram@0 {
			compatible = "rockchip,rk3066-smp-sram";
			reg = <0x00 0x10>;
		};
	};

	gpu: gpu@10090000 {
		compatible = "rockchip,rk3036-mali", "arm,mali-400";
		reg = <0x10090000 0x10000>;
		interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-names = "gp",
				  "gpmmu",
				  "pp0",
				  "ppmmu0";
		assigned-clocks = <&cru SCLK_GPU>;
		assigned-clock-rates = <100000000>;
		clocks = <&cru SCLK_GPU>, <&cru SCLK_GPU>;
		clock-names = "bus", "core";
		resets = <&cru SRST_GPU>;
		status = "disabled";
	};

	vop: vop@10118000 {
		compatible = "rockchip,rk3036-vop";
		reg = <0x10118000 0x19c>;
		interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru ACLK_LCDC>, <&cru SCLK_LCDC>, <&cru HCLK_LCDC>;
		clock-names = "aclk_vop", "dclk_vop", "hclk_vop";
		resets = <&cru SRST_LCDC1_A>, <&cru SRST_LCDC1_H>, <&cru SRST_LCDC1_D>;
		reset-names = "axi", "ahb", "dclk";
		iommus = <&vop_mmu>;
		status = "disabled";

		vop_out: port {
			#address-cells = <1>;
			#size-cells = <0>;
			vop_out_hdmi: endpoint@0 {
				reg = <0>;
				remote-endpoint = <&hdmi_in_vop>;
			};
		};
	};

	vop_mmu: iommu@10118300 {
		compatible = "rockchip,iommu";
		reg = <0x10118300 0x100>;
		interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-names = "vop_mmu";
		clocks = <&cru ACLK_LCDC>, <&cru HCLK_LCDC>;
		clock-names = "aclk", "iface";
		#iommu-cells = <0>;
		status = "disabled";
	};

	gic: interrupt-controller@10139000 {
		compatible = "arm,gic-400";
		interrupt-controller;
		#interrupt-cells = <3>;
		#address-cells = <0>;

		reg = <0x10139000 0x1000>,
		      <0x1013a000 0x2000>,
		      <0x1013c000 0x2000>,
		      <0x1013e000 0x2000>;
		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
	};

	usb_otg: usb@10180000 {
		compatible = "rockchip,rk3036-usb", "rockchip,rk3066-usb",
				"snps,dwc2";
		reg = <0x10180000 0x40000>;
		interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru HCLK_OTG0>;
		clock-names = "otg";
		dr_mode = "otg";
		g-np-tx-fifo-size = <16>;
		g-rx-fifo-size = <275>;
		g-tx-fifo-size = <256 128 128 64 64 32>;
		status = "disabled";
	};

	usb_host: usb@101c0000 {
		compatible = "rockchip,rk3036-usb", "rockchip,rk3066-usb",
				"snps,dwc2";
		reg = <0x101c0000 0x40000>;
		interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru HCLK_OTG1>;
		clock-names = "otg";
		dr_mode = "host";
		status = "disabled";
	};

	emac: ethernet@10200000 {
		compatible = "rockchip,rk3036-emac", "snps,arc-emac";
		reg = <0x10200000 0x4000>;
		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
		#address-cells = <1>;
		#size-cells = <0>;
		rockchip,grf = <&grf>;
		clocks = <&cru HCLK_MAC>, <&cru SCLK_MACREF>, <&cru SCLK_MAC>;
		clock-names = "hclk", "macref", "macclk";
		/*
		 * Fix the emac parent clock is DPLL instead of APLL.
		 * since that will cause some unstable things if the cpufreq
		 * is working. (e.g: the accurate 50MHz what mac_ref need)
		 */
		assigned-clocks = <&cru SCLK_MACPLL>;
		assigned-clock-parents = <&cru PLL_DPLL>;
		max-speed = <100>;
		phy-mode = "rmii";
		status = "disabled";
	};

	sdmmc: dwmmc@10214000 {
		compatible = "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc";
		reg = <0x10214000 0x4000>;
		clock-frequency = <37500000>;
		max-frequency = <37500000>;
		clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>;
		clock-names = "biu", "ciu";
		fifo-depth = <0x100>;
		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
		resets = <&cru SRST_MMC0>;
		reset-names = "reset";
		status = "disabled";
	};

	sdio: dwmmc@10218000 {
		compatible = "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc";
		reg = <0x10218000 0x4000>;
		max-frequency = <37500000>;
		clocks = <&cru HCLK_SDIO>, <&cru SCLK_SDIO>,
			 <&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>;
		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
		fifo-depth = <0x100>;
		interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
		resets = <&cru SRST_SDIO>;
		reset-names = "reset";
		status = "disabled";
	};

	emmc: dwmmc@1021c000 {
		compatible = "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc";
		reg = <0x1021c000 0x4000>;
		interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
		bus-width = <8>;
		cap-mmc-highspeed;
		clock-frequency = <37500000>;
		max-frequency = <37500000>;
		clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>,
			 <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
		default-sample-phase = <158>;
		disable-wp;
		dmas = <&pdma 12>;
		dma-names = "rx-tx";
		fifo-depth = <0x100>;
		mmc-ddr-1_8v;
		non-removable;
		pinctrl-names = "default";
		pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
		resets = <&cru SRST_EMMC>;
		reset-names = "reset";
		status = "disabled";
	};

	i2s: i2s@10220000 {
		compatible = "rockchip,rk3036-i2s", "rockchip,rk3066-i2s";
		reg = <0x10220000 0x4000>;
		interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
		#address-cells = <1>;
		#size-cells = <0>;
		clock-names = "i2s_clk", "i2s_hclk";
		clocks = <&cru SCLK_I2S>, <&cru HCLK_I2S>;
		dmas = <&pdma 0>, <&pdma 1>;
		dma-names = "tx", "rx";
		pinctrl-names = "default";
		pinctrl-0 = <&i2s_bus>;
		status = "disabled";
	};

	cru: clock-controller@20000000 {
		compatible = "rockchip,rk3036-cru";
		reg = <0x20000000 0x1000>;
		rockchip,grf = <&grf>;
		#clock-cells = <1>;
		#reset-cells = <1>;
		assigned-clocks = <&cru PLL_GPLL>;
		assigned-clock-rates = <594000000>;
	};

	grf: syscon@20008000 {
		compatible = "rockchip,rk3036-grf", "syscon", "simple-mfd";
		reg = <0x20008000 0x1000>;

		reboot-mode {
			compatible = "syscon-reboot-mode";
			offset = <0x1d8>;
			mode-normal = <BOOT_NORMAL>;
			mode-recovery = <BOOT_RECOVERY>;
			mode-bootloader = <BOOT_FASTBOOT>;
			mode-loader = <BOOT_BL_DOWNLOAD>;
		};
	};

	acodec: acodec-ana@20030000 {
		compatible = "rk3036-codec";
		reg = <0x20030000 0x4000>;
		rockchip,grf = <&grf>;
		clock-names = "acodec_pclk";
		clocks = <&cru PCLK_ACODEC>;
		status = "disabled";
	};

	hdmi: hdmi@20034000 {
		compatible = "rockchip,rk3036-inno-hdmi";
		reg = <0x20034000 0x4000>;
		interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru  PCLK_HDMI>;
		clock-names = "pclk";
		rockchip,grf = <&grf>;
		pinctrl-names = "default";
		pinctrl-0 = <&hdmi_ctl>;
		status = "disabled";

		hdmi_in: port {
			#address-cells = <1>;
			#size-cells = <0>;
			hdmi_in_vop: endpoint@0 {
				reg = <0>;
				remote-endpoint = <&vop_out_hdmi>;
			};
		};
	};

	timer: timer@20044000 {
		compatible = "rockchip,rk3036-timer", "rockchip,rk3288-timer";
		reg = <0x20044000 0x20>;
		interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&xin24m>, <&cru PCLK_TIMER>;
		clock-names = "timer", "pclk";
	};

	pwm0: pwm@20050000 {
		compatible = "rockchip,rk3036-pwm", "rockchip,rk2928-pwm";
		reg = <0x20050000 0x10>;
		#pwm-cells = <3>;
		clocks = <&cru PCLK_PWM>;
		clock-names = "pwm";
		pinctrl-names = "default";
		pinctrl-0 = <&pwm0_pin>;
		status = "disabled";
	};

	pwm1: pwm@20050010 {
		compatible = "rockchip,rk3036-pwm", "rockchip,rk2928-pwm";
		reg = <0x20050010 0x10>;
		#pwm-cells = <3>;
		clocks = <&cru PCLK_PWM>;
		clock-names = "pwm";
		pinctrl-names = "default";
		pinctrl-0 = <&pwm1_pin>;
		status = "disabled";
	};

	pwm2: pwm@20050020 {
		compatible = "rockchip,rk3036-pwm", "rockchip,rk2928-pwm";
		reg = <0x20050020 0x10>;
		#pwm-cells = <3>;
		clocks = <&cru PCLK_PWM>;
		clock-names = "pwm";
		pinctrl-names = "default";
		pinctrl-0 = <&pwm2_pin>;
		status = "disabled";
	};

	pwm3: pwm@20050030 {
		compatible = "rockchip,rk3036-pwm", "rockchip,rk2928-pwm";
		reg = <0x20050030 0x10>;
		#pwm-cells = <2>;
		clocks = <&cru PCLK_PWM>;
		clock-names = "pwm";
		pinctrl-names = "default";
		pinctrl-0 = <&pwm3_pin>;
		status = "disabled";
	};

	i2c1: i2c@20056000 {
		compatible = "rockchip,rk3036-i2c", "rockchip,rk3288-i2c";
		reg = <0x20056000 0x1000>;
		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
		#address-cells = <1>;
		#size-cells = <0>;
		clock-names = "i2c";
		clocks = <&cru PCLK_I2C1>;
		pinctrl-names = "default";
		pinctrl-0 = <&i2c1_xfer>;
		status = "disabled";
	};

	i2c2: i2c@2005a000 {
		compatible = "rockchip,rk3036-i2c", "rockchip,rk3288-i2c";
		reg = <0x2005a000 0x1000>;
		interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
		#address-cells = <1>;
		#size-cells = <0>;
		clock-names = "i2c";
		clocks = <&cru PCLK_I2C2>;
		pinctrl-names = "default";
		pinctrl-0 = <&i2c2_xfer>;
		status = "disabled";
	};

	uart0: serial@20060000 {
		compatible = "rockchip,rk3036-uart", "snps,dw-apb-uart";
		reg = <0x20060000 0x100>;
		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
		reg-shift = <2>;
		reg-io-width = <4>;
		clock-frequency = <24000000>;
		clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
		clock-names = "baudclk", "apb_pclk";
		pinctrl-names = "default";
		pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
		status = "disabled";
	};

	uart1: serial@20064000 {
		compatible = "rockchip,rk3036-uart", "snps,dw-apb-uart";
		reg = <0x20064000 0x100>;
		interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
		reg-shift = <2>;
		reg-io-width = <4>;
		clock-frequency = <24000000>;
		clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
		clock-names = "baudclk", "apb_pclk";
		pinctrl-names = "default";
		pinctrl-0 = <&uart1_xfer>;
		status = "disabled";
	};

	uart2: serial@20068000 {
		compatible = "rockchip,rk3036-uart", "snps,dw-apb-uart";
		reg = <0x20068000 0x100>;
		interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
		reg-shift = <2>;
		reg-io-width = <4>;
		clock-frequency = <24000000>;
		clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
		clock-names = "baudclk", "apb_pclk";
		pinctrl-names = "default";
		pinctrl-0 = <&uart2_xfer>;
		status = "disabled";
	};

	i2c0: i2c@20072000 {
		compatible = "rockchip,rk3036-i2c", "rockchip,rk3288-i2c";
		reg = <0x20072000 0x1000>;
		interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
		#address-cells = <1>;
		#size-cells = <0>;
		clock-names = "i2c";
		clocks = <&cru PCLK_I2C0>;
		pinctrl-names = "default";
		pinctrl-0 = <&i2c0_xfer>;
		status = "disabled";
	};

	spi: spi@20074000 {
		compatible = "rockchip,rockchip-spi";
		reg = <0x20074000 0x1000>;
		interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
		clocks =<&cru PCLK_SPI>, <&cru SCLK_SPI>;
		clock-names = "apb-pclk","spi_pclk";
		dmas = <&pdma 8>, <&pdma 9>;
		dma-names = "tx", "rx";
		pinctrl-names = "default";
		pinctrl-0 = <&spi_txd &spi_rxd &spi_clk &spi_cs0>;
		#address-cells = <1>;
		#size-cells = <0>;
		status = "disabled";
	};

	pinctrl: pinctrl {
		compatible = "rockchip,rk3036-pinctrl";
		rockchip,grf = <&grf>;
		#address-cells = <1>;
		#size-cells = <1>;
		ranges;

		gpio0: gpio0@2007c000 {
			compatible = "rockchip,gpio-bank";
			reg = <0x2007c000 0x100>;
			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&cru PCLK_GPIO0>;

			gpio-controller;
			#gpio-cells = <2>;

			interrupt-controller;
			#interrupt-cells = <2>;
		};

		gpio1: gpio1@20080000 {
			compatible = "rockchip,gpio-bank";
			reg = <0x20080000 0x100>;
			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&cru PCLK_GPIO1>;

			gpio-controller;
			#gpio-cells = <2>;

			interrupt-controller;
			#interrupt-cells = <2>;
		};

		gpio2: gpio2@20084000 {
			compatible = "rockchip,gpio-bank";
			reg = <0x20084000 0x100>;
			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&cru PCLK_GPIO2>;

			gpio-controller;
			#gpio-cells = <2>;

			interrupt-controller;
			#interrupt-cells = <2>;
		};

		pcfg_pull_default: pcfg_pull_default {
			bias-pull-pin-default;
		};

		pcfg_pull_none: pcfg-pull-none {
			bias-disable;
		};

		pwm0 {
			pwm0_pin: pwm0-pin {
				rockchip,pins = <0 0 RK_FUNC_2 &pcfg_pull_none>;
			};
		};

		pwm1 {
			pwm1_pin: pwm1-pin {
				rockchip,pins = <0 1 RK_FUNC_2 &pcfg_pull_none>;
			};
		};

		pwm2 {
			pwm2_pin: pwm2-pin {
				rockchip,pins = <0 1 2 &pcfg_pull_none>;
			};
		};

		pwm3 {
			pwm3_pin: pwm3-pin {
				rockchip,pins = <0 27 1 &pcfg_pull_none>;
			};
		};

		sdmmc {
			sdmmc_clk: sdmmc-clk {
				rockchip,pins = <1 16 RK_FUNC_1 &pcfg_pull_none>;
			};

			sdmmc_cmd: sdmmc-cmd {
				rockchip,pins = <1 15 RK_FUNC_1 &pcfg_pull_default>;
			};

			sdmmc_cd: sdmmc-cd {
				rockchip,pins = <1 17 RK_FUNC_1 &pcfg_pull_default>;
			};

			sdmmc_bus1: sdmmc-bus1 {
				rockchip,pins = <1 18 RK_FUNC_1 &pcfg_pull_default>;
			};

			sdmmc_bus4: sdmmc-bus4 {
				rockchip,pins = <1 18 RK_FUNC_1 &pcfg_pull_default>,
						<1 19 RK_FUNC_1 &pcfg_pull_default>,
						<1 20 RK_FUNC_1 &pcfg_pull_default>,
						<1 21 RK_FUNC_1 &pcfg_pull_default>;
			};
		};

		sdio {
			sdio_bus1: sdio-bus1 {
				rockchip,pins = <0 11 RK_FUNC_1 &pcfg_pull_default>;
			};

			sdio_bus4: sdio-bus4 {
				rockchip,pins = <0 11 RK_FUNC_1 &pcfg_pull_default>,
						<0 12 RK_FUNC_1 &pcfg_pull_default>,
						<0 13 RK_FUNC_1 &pcfg_pull_default>,
						<0 14 RK_FUNC_1 &pcfg_pull_default>;
			};

			sdio_cmd: sdio-cmd {
				rockchip,pins = <0 8 RK_FUNC_1 &pcfg_pull_default>;
			};

			sdio_clk: sdio-clk {
				rockchip,pins = <0 9 RK_FUNC_1 &pcfg_pull_none>;
			};
		};

		emmc {
			/*
			 * We run eMMC at max speed; bump up drive strength.
			 * We also have external pulls, so disable the internal ones.
			 */
			emmc_clk: emmc-clk {
				rockchip,pins = <2 4 RK_FUNC_2 &pcfg_pull_none>;
			};

			emmc_cmd: emmc-cmd {
				rockchip,pins = <2 1 RK_FUNC_2 &pcfg_pull_default>;
			};

			emmc_bus8: emmc-bus8 {
				rockchip,pins = <1 24 RK_FUNC_2 &pcfg_pull_default>,
						<1 25 RK_FUNC_2 &pcfg_pull_default>,
						<1 26 RK_FUNC_2 &pcfg_pull_default>,
						<1 27 RK_FUNC_2 &pcfg_pull_default>,
						<1 28 RK_FUNC_2 &pcfg_pull_default>,
						<1 29 RK_FUNC_2 &pcfg_pull_default>,
						<1 30 RK_FUNC_2 &pcfg_pull_default>,
						<1 31 RK_FUNC_2 &pcfg_pull_default>;
			};
		};

		emac {
			emac_xfer: emac-xfer {
				rockchip,pins = <2 10 RK_FUNC_1 &pcfg_pull_default>, /* crs_dvalid */
						<2 13 RK_FUNC_1 &pcfg_pull_default>, /* tx_en */
						<2 14 RK_FUNC_1 &pcfg_pull_default>, /* mac_clk */
						<2 15 RK_FUNC_1 &pcfg_pull_default>, /* rx_err */
						<2 16 RK_FUNC_1 &pcfg_pull_default>, /* rxd1 */
						<2 17 RK_FUNC_1 &pcfg_pull_default>, /* rxd0 */
						<2 18 RK_FUNC_1 &pcfg_pull_default>, /* txd1 */
						<2 19 RK_FUNC_1 &pcfg_pull_default>; /* txd0 */
			};

			emac_mdio: emac-mdio {
				rockchip,pins = <2 12 RK_FUNC_1 &pcfg_pull_default>, /* mac_md */
						<2 25 RK_FUNC_1 &pcfg_pull_default>; /* mac_mdclk */
			};
		};

		i2c0 {
			i2c0_xfer: i2c0-xfer {
				rockchip,pins = <0 0 RK_FUNC_1 &pcfg_pull_none>,
						<0 1 RK_FUNC_1 &pcfg_pull_none>;
			};
		};

		i2c1 {
			i2c1_xfer: i2c1-xfer {
				rockchip,pins = <0 2 RK_FUNC_1 &pcfg_pull_none>,
						<0 3 RK_FUNC_1 &pcfg_pull_none>;
			};
		};

		i2c2 {
			i2c2_xfer: i2c2-xfer {
				rockchip,pins = <2 20 RK_FUNC_1 &pcfg_pull_none>,
						<2 21 RK_FUNC_1 &pcfg_pull_none>;
			};
		};

		i2s {
			i2s_bus: i2s-bus {
				rockchip,pins = <1 0 RK_FUNC_1 &pcfg_pull_default>,
						<1 1 RK_FUNC_1 &pcfg_pull_default>,
						<1 2 RK_FUNC_1 &pcfg_pull_default>,
						<1 3 RK_FUNC_1 &pcfg_pull_default>,
						<1 4 RK_FUNC_1 &pcfg_pull_default>,
						<1 5 RK_FUNC_1 &pcfg_pull_default>;
			};
		};

		hdmi {
			hdmi_ctl: hdmi-ctl {
				rockchip,pins = <1 8  RK_FUNC_1 &pcfg_pull_none>,
						<1 9  RK_FUNC_1 &pcfg_pull_none>,
						<1 10 RK_FUNC_1 &pcfg_pull_none>,
						<1 11 RK_FUNC_1 &pcfg_pull_none>;
			};
		};

		uart0 {
			uart0_xfer: uart0-xfer {
				rockchip,pins = <0 16 RK_FUNC_1 &pcfg_pull_default>,
						<0 17 RK_FUNC_1 &pcfg_pull_none>;
			};

			uart0_cts: uart0-cts {
				rockchip,pins = <0 18 RK_FUNC_1 &pcfg_pull_default>;
			};

			uart0_rts: uart0-rts {
				rockchip,pins = <0 19 RK_FUNC_1 &pcfg_pull_none>;
			};
		};

		uart1 {
			uart1_xfer: uart1-xfer {
				rockchip,pins = <2 22 RK_FUNC_1 &pcfg_pull_default>,
						<2 23 RK_FUNC_1 &pcfg_pull_none>;
			};
			/* no rts / cts for uart1 */
		};

		uart2 {
			uart2_xfer: uart2-xfer {
				rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_default>,
						<1 19 RK_FUNC_2 &pcfg_pull_none>;
			};
			/* no rts / cts for uart2 */
		};

		spi-pins {
			spi_txd:spi-txd {
				rockchip,pins = <1 29 RK_FUNC_3 &pcfg_pull_default>;
			};

			spi_rxd:spi-rxd {
				rockchip,pins = <1 28 RK_FUNC_3 &pcfg_pull_default>;
			};

			spi_clk:spi-clk {
				rockchip,pins = <2 0 RK_FUNC_2 &pcfg_pull_default>;
			};

			spi_cs0:spi-cs0 {
				rockchip,pins = <1 30 RK_FUNC_3 &pcfg_pull_default>;

			};

			spi_cs1:spi-cs1 {
				rockchip,pins = <1 31 RK_FUNC_3 &pcfg_pull_default>;

			};
		};
	};
};