/*
 * Copyright 2003 Digi International (www.digi.com)
 *	Scott H Kilau <Scott_Kilau at digi dot com>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2, or (at your option)
 * any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY, EXPRESS OR IMPLIED; without even the
 * implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
 * PURPOSE.  See the GNU General Public License for more details.
 */

#ifndef _DGNC_NEO_H
#define _DGNC_NEO_H

#include "dgnc_driver.h"

/**
 * struct neo_uart_struct - Per channel/port NEO UART structure
 *
 * key - W = read write
 *     - R = read only
 *     - U = unused
 *
 * @txrx: (RW) Holding Register.
 * @ier: (RW) Interrupt Enable Register.
 * @isr_fcr: (RW) Interrupt Status Reg/Fifo Control Register.
 * @lcr: (RW) Line Control Register.
 * @mcr: (RW) Modem Control Register.
 * @lsr: (RW) Line Status Register.
 * @msr: (RW) Modem Status Register.
 * @spr: (RW) Scratch Pad Register.
 * @fctr: (RW) Feature Control Register.
 * @efr: (RW) Enhanced Function Register.
 * @tfifo: (RW) Transmit FIFO Register.
 * @rfifo: (RW) Receive  FIFO Register.
 * @xoffchar1: (RW) XOff Character 1 Register.
 * @xoffchar2: (RW) XOff Character 2 Register.
 * @xonchar1: (RW) Xon Character 1 Register.
 * @xonchar2: (RW) XOn Character 2 Register.
 * @reserved1: (U) Reserved by Exar.
 * @txrxburst: (RW)  64 bytes of RX/TX FIFO Data.
 * @reserved2: (U) Reserved by Exar.
 * @rxburst_with_errors: (R) bytes of RX FIFO Data + LSR.
 */
struct neo_uart_struct {
	u8 txrx;
	u8 ier;
	u8 isr_fcr;

	u8 lcr;
	u8 mcr;
	u8 lsr;
	u8 msr;
	u8 spr;
	u8 fctr;
	u8 efr;
	u8 tfifo;
	u8 rfifo;
	u8 xoffchar1;
	u8 xoffchar2;
	u8 xonchar1;
	u8 xonchar2;

	u8 reserved1[0x2ff - 0x200];
	u8 txrxburst[64];
	u8 reserved2[0x37f - 0x340];
	u8 rxburst_with_errors[64];
};

/* Where to read the extended interrupt register (32bits instead of 8bits) */
#define	UART_17158_POLL_ADDR_OFFSET	0x80

/* These are the current dvid's of the Neo boards */
#define UART_XR17C158_DVID 0x20
#define UART_XR17D158_DVID 0x20
#define UART_XR17E158_DVID 0x40

#define NEO_EECK  0x10		/* Clock */
#define NEO_EECS  0x20		/* Chip Select */
#define NEO_EEDI  0x40		/* Data In  is an Output Pin */
#define NEO_EEDO  0x80		/* Data Out is an Input Pin */
#define NEO_EEREG 0x8E		/* offset to EEPROM control reg */

#define NEO_VPD_IMAGESIZE 0x40	/* size of image to read from EEPROM in words */
#define NEO_VPD_IMAGEBYTES (NEO_VPD_IMAGESIZE * 2)

/*
 * These are the redefinitions for the FCTR on the XR17C158, since
 * Exar made them different than their earlier design. (XR16C854)
 */

/* These are only applicable when table D is selected */
#define UART_17158_FCTR_RTS_NODELAY	0x00
#define UART_17158_FCTR_RTS_4DELAY	0x01
#define UART_17158_FCTR_RTS_6DELAY	0x02
#define UART_17158_FCTR_RTS_8DELAY	0x03
#define UART_17158_FCTR_RTS_12DELAY	0x12
#define UART_17158_FCTR_RTS_16DELAY	0x05
#define UART_17158_FCTR_RTS_20DELAY	0x13
#define UART_17158_FCTR_RTS_24DELAY	0x06
#define UART_17158_FCTR_RTS_28DELAY	0x14
#define UART_17158_FCTR_RTS_32DELAY	0x07
#define UART_17158_FCTR_RTS_36DELAY	0x16
#define UART_17158_FCTR_RTS_40DELAY	0x08
#define UART_17158_FCTR_RTS_44DELAY	0x09
#define UART_17158_FCTR_RTS_48DELAY	0x10
#define UART_17158_FCTR_RTS_52DELAY	0x11

#define UART_17158_FCTR_RTS_IRDA	0x10
#define UART_17158_FCTR_RS485		0x20
#define UART_17158_FCTR_TRGA		0x00
#define UART_17158_FCTR_TRGB		0x40
#define UART_17158_FCTR_TRGC		0x80
#define UART_17158_FCTR_TRGD		0xC0

/* 17158 trigger table selects.. */
#define UART_17158_FCTR_BIT6		0x40
#define UART_17158_FCTR_BIT7		0x80

/* 17158 TX/RX memmapped buffer offsets */
#define UART_17158_RX_FIFOSIZE		64
#define UART_17158_TX_FIFOSIZE		64

/* 17158 Extended IIR's */
#define UART_17158_IIR_RDI_TIMEOUT	0x0C	/* Receiver data TIMEOUT */
#define UART_17158_IIR_XONXOFF		0x10	/* Received an XON/XOFF char */
#define UART_17158_IIR_HWFLOW_STATE_CHANGE 0x20	/* CTS/DSR or RTS/DTR
						 * state change
						 */
#define UART_17158_IIR_FIFO_ENABLED	0xC0	/* 16550 FIFOs are Enabled */

/*
 * These are the extended interrupts that get sent
 * back to us from the UART's 32bit interrupt register
 */
#define UART_17158_RX_LINE_STATUS	0x1	/* RX Ready */
#define UART_17158_RXRDY_TIMEOUT	0x2	/* RX Ready Timeout */
#define UART_17158_TXRDY		0x3	/* TX Ready */
#define UART_17158_MSR			0x4	/* Modem State Change */
#define UART_17158_TX_AND_FIFO_CLR	0x40	/* Transmitter Holding
						 * Reg Empty
						 */
#define UART_17158_RX_FIFO_DATA_ERROR	0x80	/* UART detected an RX FIFO
						 * Data error
						 */

/*
 * These are the EXTENDED definitions for the 17C158's Interrupt
 * Enable Register.
 */
#define UART_17158_EFR_ECB	0x10	/* Enhanced control bit */
#define UART_17158_EFR_IXON	0x2	/* Receiver compares Xon1/Xoff1 */
#define UART_17158_EFR_IXOFF	0x8	/* Transmit Xon1/Xoff1 */
#define UART_17158_EFR_RTSDTR	0x40	/* Auto RTS/DTR Flow Control Enable */
#define UART_17158_EFR_CTSDSR	0x80	/* Auto CTS/DSR Flow Control Enable */

#define UART_17158_XOFF_DETECT	0x1	/* Indicates whether chip saw an
					 * incoming XOFF char
					 */
#define UART_17158_XON_DETECT	0x2	/* Indicates whether chip saw an
					 * incoming XON char
					 */

#define UART_17158_IER_RSVD1	0x10	/* Reserved by Exar */
#define UART_17158_IER_XOFF	0x20	/* Xoff Interrupt Enable */
#define UART_17158_IER_RTSDTR	0x40	/* Output Interrupt Enable */
#define UART_17158_IER_CTSDSR	0x80	/* Input Interrupt Enable */

extern struct board_ops dgnc_neo_ops;

#endif	/* _DGNC_NEO_H */