chip soc/intel/apollolake

	device cpu_cluster 0 on
		device lapic 0 on end
	end

	register "pcie_rp4_clkreq_pin" = "0"    # wifi/bt

	# EMMC TX DATA Delay 1
	# Refer to EDS-Vol2-22.3.
	# [14:8] steps of delay for HS400, each 125ps.
	# [6:0] steps of delay for SDR104/HS200, each 125ps.
	register "emmc_tx_data_cntl1" = "0x0C16"

	# EMMC TX DATA Delay 2
	# Refer to EDS-Vol2-22.3.
	# [30:24] steps of delay for SDR50, each 125ps.
	# [22:16] steps of delay for DDR50, each 125ps.
	# [14:8] steps of delay for SDR25/HS50, each 125ps.
	# [6:0] steps of delay for SDR12, each 125ps.
	register "emmc_tx_data_cntl2" = "0x28162828"

	# EMMC RX CMD/DATA Delay 1
	# Refer to EDS-Vol2-22.3.
	# [30:24] steps of delay for SDR50, each 125ps.
	# [22:16] steps of delay for DDR50, each 125ps.
	# [14:8] steps of delay for SDR25/HS50, each 125ps.
	# [6:0] steps of delay for SDR12, each 125ps.
	register "emmc_rx_cmd_data_cntl1" = "0x00181717"

	# EMMC RX CMD/DATA Delay 2
	# Refer to EDS-Vol2-22.3.
	# [17:16] stands for Rx Clock before Output Buffer
	# [14:8] steps of delay for Auto Tuning Mode, each 125ps.
	# [6:0] steps of delay for HS200, each 125ps.
	register "emmc_rx_cmd_data_cntl2" = "0x10008"

	# Enable DPTF
	register "dptf_enable" = "1"

	# GPE configuration
	# Note that GPE events called out in ASL code rely on this
	# route, i.e., if this route changes then the affected GPE
	# offset bits also need to be changed. This sets the PMC register
	# GPE_CFG fields.
	register "gpe0_dw1" = "PMC_GPE_N_31_0"
	register "gpe0_dw2" = "PMC_GPE_N_63_32"
	register "gpe0_dw3" = "PMC_GPE_SW_31_0"

	# Enable I2C2 bus early for TPM access
	register "i2c[2].early_init" = "1"

	device domain 0 on
		device pci 00.0 on  end	# - Host Bridge
		device pci 00.1 on  end	# - DPTF
		device pci 00.2 on  end	# - NPK
		device pci 02.0 on  end	# - Gen
		device pci 03.0 on  end	# - Iunit
		device pci 0d.0 on  end	# - P2SB
		device pci 0d.1 on  end	# - PMC
		device pci 0d.2 on  end	# - SPI
		device pci 0d.3 on  end	# - Shared SRAM
		device pci 0e.0 on	# - Audio
			chip drivers/generic/max98357a
				register "sdmode_gpio" =  "ACPI_GPIO_OUTPUT(GPIO_76)"
				device generic 0 on end
			end
		end
		device pci 11.0 off end	# - ISH
		device pci 12.0 off end	# - SATA
		device pci 13.0 off end	# - Root Port 2 - PCIe-A 0
		device pci 13.1 off end	# - Root Port 3 - PCIe-A 1
		device pci 13.2 off end	# - Root Port 4 - PCIe-A 2
		device pci 13.3 off end	# - Root Port 5 - PCIe-A 3
		device pci 14.0 on  end	# - Root Port 0 - PCIe-B 0 - Wifi
		device pci 14.1 off end	# - Root Port 1 - PCIe-B 1
		device pci 15.0 on  end	# - XHCI
		device pci 15.1 off end # - XDCI
		device pci 16.0 on	# - I2C 0
			chip drivers/i2c/da7219
				register "irq" = "IRQ_LEVEL_LOW(GPIO_116_IRQ)"
				register "btn_cfg" = "50"
				register "mic_det_thr" = "500"
				register "jack_ins_deb" = "20"
				register "jack_det_rate" = ""32ms_64ms""
				register "jack_rem_deb" = "1"
				register "a_d_btn_thr" = "0xa"
				register "d_b_btn_thr" = "0x16"
				register "b_c_btn_thr" = "0x21"
				register "c_mic_btn_thr" = "0x3e"
				register "btn_avg" = "4"
				register "adc_1bit_rpt" = "1"
				register "micbias_lvl" = "2600"
				register "mic_amp_in_sel" = ""diff""
				device i2c 1a on end
			end
		end
		device pci 16.1 on  end	# - I2C 1
		device pci 16.2 on  end	# - I2C 2
		device pci 16.3 on
			chip drivers/i2c/generic
			     register "hid" = ""ELAN0001""
			     register "desc" = ""ELAN Touchscreen""
			     register "irq" = "IRQ_EDGE_LOW(GPIO_21_IRQ)"
			     device i2c 10 on end
			end
		end	# - I2C 3
		device pci 17.0 on
			chip drivers/i2c/generic
				register "hid" = ""ELAN0000""
				register "desc" = ""ELAN Touchpad""
				register "irq" = "IRQ_EDGE_LOW(GPIO_18_IRQ)"
				register "wake" = "GPE0_DW1_15"
				device i2c 15 on end
			end
		end # - I2C 4
		device pci 17.1 on  end	# - I2C 5
		device pci 17.2 on  end	# - I2C 6
		device pci 17.3 on  end	# - I2C 7
		device pci 18.0 on  end	# - UART 0
		device pci 18.1 on  end	# - UART 1
		device pci 18.2 on  end	# - UART 2
		device pci 18.3 on  end	# - UART 3
		device pci 19.0 on  end	# - SPI 0
		device pci 19.1 on  end	# - SPI 1
		device pci 19.2 on  end	# - SPI 2
		device pci 1a.0 on  end	# - PWM
		device pci 1b.0 on  end	# - SDCARD
		device pci 1c.0 on  end	# - eMMC
		device pci 1e.0 off end	# - SDIO
		device pci 1f.0 on	# - LPC
			chip ec/google/chromeec
				device pnp 0c09.0 on end
			end
		end
		device pci 1f.1 on  end	# - SMBUS
	end
end