| # ITE IT8718F SuperIO EC registers |
| { |
| # 00 Configuration register |
| "conf00_start" : 1, |
| "conf00_smien" : 1, |
| "conf00_irqen" : 1, |
| "conf00_irqclr" : 1, |
| "conf00_ro_one" : 1, |
| "conf00_copen" : 1, |
| "conf00_vbat" : 1, |
| "conf00_initreset" : 1, |
| |
| # 01 Interrupt Status register 1 |
| "irq1_maxfantac1" : 1, |
| "irq1_maxfantac2" : 1, |
| "irq1_maxfantac3" : 1, |
| "irq1_maxfantac4" : 1, |
| "irq1_copen" : 1, |
| "irq1_reserved0" : 1, |
| "irq1_maxfantac5" : 1, |
| "irq1_reserved1" : 1, |
| |
| # 02 Interrupt Status register 2 |
| "irq2_limit_vin"[8] : 1, |
| |
| # 03 Interrupt Status register 3 |
| "irq3_limit_temp1" : 1, |
| "irq3_limit_temp2" : 1, |
| "irq3_limit_temp3" : 1, |
| "irq3_reserved" : 5, |
| |
| # 04 SMI Mask register 1 |
| "smi1_dis_fantac1" : 1, |
| "smi1_dis_fantac2" : 1, |
| "smi1_dis_fantac3" : 1, |
| "smi1_dis_fantac4" : 1, |
| "smi1_dis_copen" : 1, |
| "smi1_reserved0" : 1, |
| "smi1_dis_fantac5" : 1, |
| "smi1_reserved1" : 1, |
| |
| # 05 SMI Mask register 2 |
| "smi2_dis_vin"[8] : 1, |
| |
| # 06 SMI Mask register 3 |
| "smi3_dis_temp1" : 1, |
| "smi3_dis_temp2" : 1, |
| "smi3_dis_temp3" : 1, |
| "smi3_reserved" : 5, |
| |
| # 07 Interrupt Mask register 1 |
| "irqmask1_fantac1" : 1, |
| "irqmask1_fantac2" : 1, |
| "irqmask1_fantac3" : 1, |
| "irqmask1_fantac4" : 1, |
| "irqmask1_copen" : 1, |
| "irqmask1_reserved0" : 1, |
| "irqmask1_fantac5" : 1, |
| "irqmask1_reserved1" : 1, |
| |
| # 08 Interrupt Mask register 2 |
| "irqmask2_vin"[8] : 1, |
| |
| # 09 Interrupt Mask register 3 |
| "irqmask3_temp1" : 1, |
| "irqmask3_temp2" : 1, |
| "irqmask3_temp3" : 1, |
| "irqmask3_reserved" : 4, |
| "irqmask3_extsensor" : 1, |
| |
| # 0a Interface Selection register |
| "iface_reserved" : 4, |
| "iface_extsensor_select": 3, |
| "iface_pseudo_eoc" : 1, |
| |
| # 0b Fan PWM smoothing step selection reg |
| "fanpwm_reserved" : 6, |
| "fanpwm_smoothing_step" : 2, |
| |
| # 0c Fan Tachometer 16 bit enable register |
| "fantach16_en_tac1" : 1, |
| "fantach16_en_tac2" : 1, |
| "fantach16_en_tac3" : 1, |
| "fantach16_tmpin1_enh" : 1, |
| "fantach16_en_tac4" : 1, |
| "fantach16_en_tac5" : 1, |
| "fantach16_tmpin2_enh" : 1, |
| "fantach16_tmpin3_enh" : 1, |
| |
| # 0d-0f Fan Tachmometer read registers |
| "fantach_lo_counts1" : 8, |
| "fantach_lo_counts2" : 8, |
| "fantach_lo_counts3" : 8, |
| |
| # 10-12 Fan Tachometer limit registers |
| "fantach_lo_limit1" : 8, |
| "fantach_lo_limit2" : 8, |
| "fantach_lo_limit3" : 8, |
| |
| # 13 Fan controller main control register |
| "fanctlmain_mode1" : 1, |
| "fanctlmain_mode2" : 1, |
| "fanctlmain_mode3" : 1, |
| "fanctlmain_reserved0" : 1, |
| "fanctlmain_en_tac1" : 1, |
| "fanctlmain_en_tac2" : 1, |
| "fanctlmain_en_tac3" : 1, |
| "fanctlmain_reserved1" : 1, |
| |
| # 14 FAN_CTL control register |
| "fanctl_enable1" : 1, |
| "fanctl_enable2" : 1, |
| "fanctl_enable3" : 1, |
| "fanctl_minduty_sel" : 1, |
| # 000: 48Mhz (PWM Frequency 375Khz) |
| # 001: 24Mhz (PWM Frequency 187.5Khz) |
| # 010: 12Mhz (PWM Frequency 93.75Khz) |
| # 011: 8Mhz (PWM Frequency 62.5Khz) |
| # 100: 6Mhz (PWM Frequency 46.875Khz) |
| # 101: 3Mhz (PWM Frequency 23.43Khz) |
| # 110: 1.5Mhz (PWM Frequency 11.7Khz) |
| # 111: 0.75Mhz (PWM Frequency 5.86Khz) |
| "fanctl_pwm_base_clock" : 3, |
| "fanctl_allpolarity" : 1, |
| |
| # 15 FAN_CTL1 PWM control register |
| "fanctl1_tmpin_sel" : 2, |
| "fanctl1_steps" : 5, |
| "fanctl1_pwm_mode" : 1, |
| |
| # 16 FAN_CTL2 PWM control register |
| "fanctl2_tmpin_sel" : 2, |
| "fanctl2_steps" : 5, |
| "fanctl2_pwm_mode" : 1, |
| |
| # 17 FAN_CTL3 PWM control register |
| "fanctl3_tmpin_sel" : 2, |
| "fanctl3_steps" : 5, |
| "fanctl3_pwm_mode" : 1, |
| |
| # 18-1a Fan Tachometer extended read registers |
| "fantach_hi_counts1" : 8, |
| "fantach_hi_counts2" : 8, |
| "fantach_hi_counts3" : 8, |
| |
| # 1b-1d Fan Tachometer extended limit registers |
| "fantach_hi_limit1" : 8, |
| "fantach_hi_limit2" : 8, |
| "fantach_hi_limit3" : 8, |
| |
| "reserved1e" : 8, |
| "reserved1f" : 8, |
| |
| |
| # 20-27 Reading registers |
| "vin"[8] : 8, |
| |
| "vbat" : 8, |
| "tmpin1" : 8, |
| "tmpin2" : 8, |
| "tmpin3" : 8, |
| "reserved2c" : 8, |
| "reserved2d" : 8, |
| "reserved2e" : 8, |
| "reserved2f" : 8, |
| "limit_hi_vin0" : 8, |
| "limit_lo_vin0" : 8, |
| "limit_hi_vin1" : 8, |
| "limit_lo_vin1" : 8, |
| "limit_hi_vin2" : 8, |
| "limit_lo_vin2" : 8, |
| "limit_hi_vin3" : 8, |
| "limit_lo_vin3" : 8, |
| "limit_hi_vin4" : 8, |
| "limit_lo_vin4" : 8, |
| "limit_hi_vin5" : 8, |
| "limit_lo_vin5" : 8, |
| "limit_hi_vin6" : 8, |
| "limit_lo_vin6" : 8, |
| "limit_hi_vin7" : 8, |
| "limit_lo_vin7" : 8, |
| "limit_hi_tmpin1" : 8, |
| "limit_lo_tmpin1" : 8, |
| "limit_hi_tmpin2" : 8, |
| "limit_lo_tmpin2" : 8, |
| "limit_hi_tmpin3" : 8, |
| "limit_lo_tmpin3" : 8, |
| |
| "reserved46" : 8, |
| "reserved47" : 8, |
| "reserved48" : 8, |
| "reserved49" : 8, |
| "reserved4a" : 8, |
| "reserved4b" : 8, |
| "reserved4c" : 8, |
| "reserved4d" : 8, |
| "reserved4e" : 8, |
| "reserved4f" : 8, |
| |
| # 50 ADC Voltage channel enable register |
| "adc_scan_enable_vin"[8]: 1, |
| |
| # 51 ADC Temperature channel enable register |
| "therm_diode_tmpin1" : 1, |
| "therm_diode_tmpin2" : 1, |
| "therm_diode_tmpin3" : 1, |
| # Mututally exclusive settings |
| "therm_resistor_tmpin1" : 1, |
| "therm_resistor_tmpin2" : 1, |
| "therm_resistor_tmpin3" : 1, |
| "therm_reserved" : 2, |
| |
| "therm_limit_tmpin1" : 8, |
| "therm_limit_tmpin2" : 8, |
| "therm_limit_tmpin3" : 8, |
| |
| # 55 Temperature extra channel enable reg |
| "therm_resistor_vin4" : 1, |
| "therm_resistor_vin5" : 1, |
| "therm_resistor_vin6" : 1, |
| "adc_fanctl2_pwm_duty" : 1, |
| # 000: 48Mhz (PWM Frequency 375Khz) |
| # 001: 24Mhz (PWM Frequency 187.5Khz) |
| # 010: 12Mhz (PWM Frequency 93.75Khz) |
| # 011: 8Mhz (PWM Frequency 62.5Khz) |
| # 100: 6Mhz (PWM Frequency 46.875Khz) |
| # 101: 3Mhz (PWM Frequency 23.43Khz) |
| # 110: 1.5Mhz (PWM Frequency 11.7Khz) |
| # 111: 0.75Mhz (PWM Frequency 5.86Khz) |
| "adc_fanctl2_pwm_bclk" : 3, |
| "adc_tmpin3_ext_select" : 1, |
| |
| "thermal_zero_diode1" : 8, |
| "thermal_zero_diode2" : 8, |
| "ite_vendor_id" : 8, |
| "thermal_zero_diode3" : 8, |
| "reserved5a" : 8, |
| "ite_code_id" : 8, |
| |
| "beep_fantac" : 1, |
| "beep_vin" : 1, |
| "beep_tmpin" : 1, |
| "beep_reserved" : 1, |
| # ADC clock select |
| # 000: 500Khz (Default) |
| # 001: 250Khz |
| # 010: 125K |
| # 011: 62.5Khz |
| # 100: 31.25Khz |
| # 101: 24Mhz |
| # 110: 1Mhz |
| # 111: 2Mhz |
| "adc_clock_select" : 3, |
| "thermal_zero_adj_en" : 1, |
| |
| "beep_fan_freq_div" : 4, |
| "beep_fan_tone_div" : 4, |
| "beep_volt_freq_div" : 4, |
| "beep_volt_tone_div" : 4, |
| "beep_temp_freq_div" : 4, |
| "beep_temp_tone_div" : 4, |
| |
| # 60 SmartGuardian registers |
| "sguard1_temp_lim_off" : 8, |
| "sguard1_temp_lim_fan" : 8, |
| "reserved62" : 8, |
| "sguard1_pwm_start" : 7, |
| "sguard1_pwm_slope6" : 1, |
| "sguard1_pwm_slope05" : 6, |
| "sguard1_pwm_reserved" : 1, |
| "sguard1_fan_smooth_en" : 1, |
| "sguard1_temp_interval" : 5, |
| "sguard1_temp_reserved" : 2, |
| "sguard1_temp_pwm_lin" : 1, |
| "reserved66" : 8, |
| "reserved67" : 8, |
| "sguard2_temp_lim_off" : 8, |
| "sguard2_temp_lim_fan" : 8, |
| "reserved6a" : 8, |
| "sguard2_pwm_start" : 7, |
| "sguard2_pwm_slope6" : 1, |
| "sguard2_pwm_slope05" : 6, |
| "sguard2_pwm_reserved" : 1, |
| "sguard2_fan_smooth_en" : 1, |
| "sguard2_temp_interval" : 5, |
| "sguard2_temp_reserved" : 2, |
| "sguard2_temp_pwm_lin" : 1, |
| "reserved6e" : 8, |
| "reserved6f" : 8, |
| "sguard3_temp_lim_off" : 8, |
| "sguard3_temp_lim_fan" : 8, |
| "reserved72" : 8, |
| "sguard3_pwm_start" : 7, |
| "sguard3_pwm_slope6" : 1, |
| "sguard3_pwm_slope05" : 6, |
| "sguard3_pwm_reserved" : 1, |
| "sguard3_fan_smooth_en" : 1, |
| "sguard3_temp_interval" : 5, |
| "sguard3_temp_reserved" : 2, |
| "sguard3_temp_pwm_lin" : 1, |
| "reserved76" : 8, |
| "reserved77" : 8, |
| "reserved78" : 8, |
| "reserved79" : 8, |
| "reserved7a" : 8, |
| "reserved7b" : 8, |
| "reserved7c" : 8, |
| "reserved7d" : 8, |
| "reserved7e" : 8, |
| "reserved7f" : 8, |
| |
| # 80 Fan Tachometer 4-5 read registers |
| "fantach_lo_counts4" : 8, |
| "fantach_hi_counts4" : 8, |
| "fantach_lo_counts5" : 8, |
| "fantach_hi_counts5" : 8, |
| "fantach_lo_limit4" : 8, |
| "fantach_hi_limit4" : 8, |
| "fantach_lo_limit5" : 8, |
| "fantach_hi_limit5" : 8, |
| |
| # 88 External temperature sensor host status |
| "ext_host_busy" : 1, |
| "ext_host_fnsh" : 1, |
| "ext_host_r_fcs_error" : 1, |
| "ext_host_w_fcs_error" : 1, |
| "ext_host_peci_highz" : 1, |
| "ext_host_sst_slave" : 1, |
| "ext_host_sst_bus" : 1, |
| "ext_host_data_fifo_clr": 1, |
| |
| "ext_host_target_addr" : 8, |
| "ext_host_write_length" : 8, |
| "ext_host_read_length" : 8, |
| "ext_host_cmd" : 8, |
| "ext_host_writedata" : 8, |
| |
| "ext_hostctl_start" : 1, |
| "ext_hostctl_sst_amdsi" : 1, |
| "ext_hostctl_sst_ctl" : 1, |
| "ext_hostctl_resetfifo" : 1, |
| "ext_hostctl_fcs_abort" : 1, |
| "ext_hostctl_start_en" : 1, |
| # Auto-Start Control |
| # The host will start the transaction |
| # at a regular rate automatically. |
| # 00: 32 Hz |
| # 01: 16 Hz |
| # 10: 8 Hz |
| # 11: 4 Hz |
| "ext_hostctl_start_ctl" : 2, |
| |
| "ext_host_readdata" : 8, |
| |
| "fan1_temp_limit_start" : 8, |
| "fan1_slope_pwm" : 7, |
| "fan1_temp_input_sel0" : 1, |
| "fan1_ctlmode_temp_ivl" : 5, |
| "fan1_ctlmode_target" : 2, |
| "fan1_temp_input_sel1" : 1, |
| "reserved93" : 8, |
| "fan2_temp_limit_start" : 8, |
| "fan2_slope_pwm" : 7, |
| "fan2_temp_input_sel0" : 1, |
| "fan2_ctlmode_temp_ivl" : 5, |
| "fan2_ctlmode_target" : 2, |
| "fan2_temp_input_sel1" : 1 |
| } |
