| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2010 LiPPERT Embedded Computers GmbH |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA |
| */ |
| |
| /* Based on mainboard.c from the SpaceRunner-LX mainboard. */ |
| |
| #include <stdlib.h> |
| #include <stdint.h> |
| #include <console/console.h> |
| #include <device/device.h> |
| #include <arch/io.h> |
| #include <device/pci.h> |
| #include <device/pci_ids.h> |
| |
| /* Bit1 switches Com1 to RS485, bit2 same for Com2. */ |
| #if CONFIG_ONBOARD_UARTS_RS485 |
| #define SIO_GP1X_CONFIG 0x06 |
| #else |
| #define SIO_GP1X_CONFIG 0x00 |
| #endif |
| |
| static const u16 ec_init_table[] = { /* hi=data, lo=index */ |
| 0x1900, /* Enable monitoring */ |
| 0x0351, /* TMPIN1,2 diode mode, TMPIN3 off */ |
| 0x805C, /* Unlock zero adjust */ |
| 0x7056, 0x3C57, /* Zero adjust TMPIN1,2 */ |
| 0x005C, /* Lock zero adjust */ |
| 0xD014 /* Also set FAN_CTL polarity to Active High */ |
| }; |
| |
| static void init(struct device *dev) |
| { |
| unsigned int gpio_base, i; |
| printk(BIOS_DEBUG, "LiPPERT Hurricane-LX ENTER %s\n", __func__); |
| |
| /* Init CS5536 GPIOs */ |
| gpio_base = pci_read_config32(dev_find_device(PCI_VENDOR_ID_AMD, |
| PCI_DEVICE_ID_AMD_CS5536_ISA, 0), PCI_BASE_ADDRESS_1) - 1; |
| |
| outl(0x00000040, gpio_base + 0x00); // GPIO6 value 1 - LAN_PD# |
| outl(0x00000040, gpio_base + 0x08); // GPIO6 open drain 1 - LAN_PD# (jumpered GPIO per default) |
| outl(0x00000040, gpio_base + 0x04); // GPIO6 output 1 - LAN_PD# |
| outl(0x00000400, gpio_base + 0x34); // GPIO10 in aux1 1 - THRM_ALRM# |
| outl(0x00000400, gpio_base + 0x20); // GPIO10 input 1 - THRM_ALRM# |
| #if !CONFIG_BOARD_OLD_REVISION |
| outl(0x00000800, gpio_base + 0x94); // GPIO27 out aux2 1 - 32kHz |
| outl(0x00000800, gpio_base + 0x84); // GPIO27 output 1 - 32kHz |
| #endif |
| outl(0x08000000, gpio_base + 0x98); // GPIO27 pull up 0 - 32kHz (new) / PM-LED (old) |
| |
| /* Init Environment Controller. */ |
| for (i = 0; i < ARRAY_SIZE(ec_init_table); i++) { |
| u16 val = ec_init_table[i]; |
| outb((u8)val, 0x0295); |
| outb(val >> 8, 0x0296); |
| } |
| |
| /* bit2 = RS485_EN2, bit1 = RS485_EN1 */ |
| outb(SIO_GP1X_CONFIG, 0x1220); /* Simple-I/O GP17-10 */ |
| |
| printk(BIOS_DEBUG, "LiPPERT Hurricane-LX EXIT %s\n", __func__); |
| } |
| |
| static void mainboard_enable(struct device *dev) |
| { |
| dev->ops->init = init; |
| } |
| |
| struct chip_operations mainboard_ops = { |
| .enable_dev = mainboard_enable, |
| }; |