blob: 4b42ef3df2cb17d7091affe72eb7172507f54cde [file] [log] [blame]
/*
* This file is part of the coreboot project.
*
* Copyright (C) 2003 Eric Biederman
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; version 2 of the License.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#ifndef __UART8250_H__
#define __UART8250_H__
/* Data */
#define UART8250_RBR 0x00
#define UART8250_TBR 0x00
/* Control */
#define UART8250_IER 0x01
#define UART8250_IER_MSI 0x08 /* Enable Modem status interrupt */
#define UART8250_IER_RLSI 0x04 /* Enable receiver line status interrupt */
#define UART8250_IER_THRI 0x02 /* Enable Transmitter holding register int. */
#define UART8250_IER_RDI 0x01 /* Enable receiver data interrupt */
#define UART8250_IIR 0x02
#define UART8250_IIR_NO_INT 0x01 /* No interrupts pending */
#define UART8250_IIR_ID 0x06 /* Mask for the interrupt ID */
#define UART8250_IIR_MSI 0x00 /* Modem status interrupt */
#define UART8250_IIR_THRI 0x02 /* Transmitter holding register empty */
#define UART8250_IIR_RDI 0x04 /* Receiver data interrupt */
#define UART8250_IIR_RLSI 0x06 /* Receiver line status interrupt */
#define UART8250_FCR 0x02
#define UART8250_FCR_FIFO_EN 0x01 /* Fifo enable */
#define UART8250_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */
#define UART8250_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */
#define UART8250_FCR_DMA_SELECT 0x08 /* For DMA applications */
#define UART8250_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */
#define UART8250_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */
#define UART8250_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */
#define UART8250_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */
#define UART8250_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */
#define UART8250_FCR_RXSR 0x02 /* Receiver soft reset */
#define UART8250_FCR_TXSR 0x04 /* Transmitter soft reset */
#define UART8250_LCR 0x03
#define UART8250_LCR_WLS_MSK 0x03 /* character length select mask */
#define UART8250_LCR_WLS_5 0x00 /* 5 bit character length */
#define UART8250_LCR_WLS_6 0x01 /* 6 bit character length */
#define UART8250_LCR_WLS_7 0x02 /* 7 bit character length */
#define UART8250_LCR_WLS_8 0x03 /* 8 bit character length */
#define UART8250_LCR_STB 0x04 /* Number of stop Bits, off = 1, on = 1.5 or 2) */
#define UART8250_LCR_PEN 0x08 /* Parity eneble */
#define UART8250_LCR_EPS 0x10 /* Even Parity Select */
#define UART8250_LCR_STKP 0x20 /* Stick Parity */
#define UART8250_LCR_SBRK 0x40 /* Set Break */
#define UART8250_LCR_BKSE 0x80 /* Bank select enable */
#define UART8250_LCR_DLAB 0x80 /* Divisor latch access bit */
#define UART8250_MCR 0x04
#define UART8250_MCR_DTR 0x01 /* DTR */
#define UART8250_MCR_RTS 0x02 /* RTS */
#define UART8250_MCR_OUT1 0x04 /* Out 1 */
#define UART8250_MCR_OUT2 0x08 /* Out 2 */
#define UART8250_MCR_LOOP 0x10 /* Enable loopback test mode */
#define UART8250_MCR_DMA_EN 0x04
#define UART8250_MCR_TX_DFR 0x08
#define UART8250_DLL 0x00
#define UART8250_DLM 0x01
/* Status */
#define UART8250_LSR 0x05
#define UART8250_LSR_DR 0x01 /* Data ready */
#define UART8250_LSR_OE 0x02 /* Overrun */
#define UART8250_LSR_PE 0x04 /* Parity error */
#define UART8250_LSR_FE 0x08 /* Framing error */
#define UART8250_LSR_BI 0x10 /* Break */
#define UART8250_LSR_THRE 0x20 /* Xmit holding register empty */
#define UART8250_LSR_TEMT 0x40 /* Xmitter empty */
#define UART8250_LSR_ERR 0x80 /* Error */
#define UART8250_MSR 0x06
#define UART8250_MSR_DCD 0x80 /* Data Carrier Detect */
#define UART8250_MSR_RI 0x40 /* Ring Indicator */
#define UART8250_MSR_DSR 0x20 /* Data Set Ready */
#define UART8250_MSR_CTS 0x10 /* Clear to Send */
#define UART8250_MSR_DDCD 0x08 /* Delta DCD */
#define UART8250_MSR_TERI 0x04 /* Trailing edge ring indicator */
#define UART8250_MSR_DDSR 0x02 /* Delta DSR */
#define UART8250_MSR_DCTS 0x01 /* Delta CTS */
#define UART8250_SCR 0x07
#define UART8250_SPR 0x07
#if CONFIG_CONSOLE_SERIAL
#if ((115200 % CONFIG_TTYS0_BAUD) != 0)
#error Bad ttyS0 baud rate
#endif
#endif
/* Line Control Settings */
#define UART8250_LCS CONFIG_TTYS0_LCS
#if CONFIG_CONSOLE_SERIAL8250
unsigned char uart8250_rx_byte(unsigned base_port);
int uart8250_can_rx_byte(unsigned base_port);
void uart8250_tx_byte(unsigned base_port, unsigned char data);
void uart8250_tx_flush(unsigned base_port);
/* Yes it is silly to have three different uart init functions. But we used to
* have three different sets of uart code, so it's an improvement.
*/
void uart8250_init(unsigned base_port, unsigned divisor);
void uart_init(void);
#endif
#if CONFIG_CONSOLE_SERIAL8250MEM
void uartmem_init(void);
/* and the same for memory mapped uarts */
unsigned char uart8250_mem_rx_byte(unsigned base_port);
int uart8250_mem_can_rx_byte(unsigned base_port);
void uart8250_mem_tx_byte(unsigned base_port, unsigned char data);
void uart8250_mem_tx_flush(unsigned base_port);
void uart8250_mem_init(unsigned base_port, unsigned divisor);
u32 uart_mem_init(void);
#if defined(__PRE_RAM__) && CONFIG_DRIVERS_OXFORD_OXPCIE
/* and special init for OXPCIe based cards */
extern int oxford_oxpcie_present;
void oxford_init(void);
#endif
#endif
#endif /* __UART8250_H__ */