/* This file was generated by getpir.c, do not modify!
 * (but if you do, please run checkpir on it to verify)
 *
 * Contains the IRQ Routing Table dumped directly from your
 * memory, which BIOS sets up.
 *
 * Documentation at: http://www.microsoft.com/whdc/archive/pciirq.mspx
 */

#ifdef GETPIR
#include "pirq_routing.h"
#else
#include <arch/pirq_routing.h>
#endif

static const struct irq_routing_table intel_irq_routing_table = {
	PIRQ_SIGNATURE,  /* u32 signature */
	PIRQ_VERSION,    /* u16 version   */
	32+16*CONFIG_IRQ_SLOT_COUNT,	 /* There can be total CONFIG_IRQ_SLOT_COUNT devices on the bus */
	0x00,		 /* Where the interrupt router lies (bus) */
	(0x11<<3)|0x0,   /* Where the interrupt router lies (dev) */
	0x1c00,		 /* IRQs devoted exclusively to PCI usage */
	0x1106,		 /* Vendor */
	0x3227,		 /* Device */
	0,		 /* Miniport */
	{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
	0xf,		 /* u8 checksum. This has to be set to some
			    value that would give 0 after the sum of all
			    bytes for this structure (including checksum) */
	{
		/* bus,     dev|fn,   {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap},  slot, rfu */
		{0x00,(0x14<<3)|0x0, {{0x03, 0xdeb8}, {0x05, 0xdeb8}, {0x01, 0xdeb8}, {0x02, 0xdeb8}}, 0x1, 0x0},
		{0x00,(0x13<<3)|0x0, {{0x05, 0xdeb8}, {0x03, 0xdeb8}, {0x02, 0xdeb8}, {0x01, 0xdeb8}}, 0x2, 0x0},
		{0x00,(0x11<<3)|0x0, {{0x00, 0xdeb8}, {0x00, 0xdeb8}, {0x03, 0xdeb8}, {0x05, 0xdeb8}}, 0x0, 0x0},
		{0x00,(0x0f<<3)|0x0, {{0x01, 0xdeb8}, {0x02, 0xdeb8}, {0x03, 0xdeb8}, {0x05, 0xdeb8}}, 0x0, 0x0},
		{0x00,(0x01<<3)|0x0, {{0x01, 0xdeb8}, {0x02, 0xdeb8}, {0x03, 0xdeb8}, {0x05, 0xdeb8}}, 0x0, 0x0},
		{0x00,(0x10<<3)|0x0, {{0x01, 0xdeb8}, {0x02, 0xdeb8}, {0x03, 0xdeb8}, {0x05, 0xdeb8}}, 0x0, 0x0},
		{0x00,(0x12<<3)|0x0, {{0x01, 0xdeb8}, {0x00, 0xdeb8}, {0x00, 0xdeb8}, {0x00, 0xdeb8}}, 0x0, 0x0},
	}
};
#ifndef GETPIR

unsigned long write_pirq_routing_table(unsigned long addr)
{
	return copy_pirq_routing_table(addr, &intel_irq_routing_table);
}
#endif